Currently the MPLSoUDP encap builds the MPLS header using encap action
information (tunnel id, ttl and tos) instead of the MPLS action
information (label, ttl, tc and bos) which is wrong.

Fix by storing the MPLS action information during the flow action
parse and later using it to create the encap MPLS header.

Fixes: f828ca6a ("net/mlx5e: Add support for hw encapsulation of MPLS over UDP")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Fec counters support is checked via the PCAM feature_cap_mask,
bit 0: PPCNT_counter_group_Phy_statistical_counter_group.
Add feature check to avoid faulty behavior.

Fixes: 0a1498eb ("net/mlx5e: Expose FEC counters via ethtool")
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Offload of ct clear action is just resetting the reg_c register.
It's done by allocating modify hdr resources which is limited.
Doing it multiple times is redundant and wasting modify hdr resources
and if resources depleted the driver will fail offloading the rule.
Ignore redundant ct clear actions after the first one.

Fixes: 806401c2 ("net/mlx5e: CT, Fix multiple allocations and memleak of mod acts")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Such rules are redundant but allowed and passed to the driver.
The driver does not support offloading such rules so return an error.

Fixes: 03a9d11e ("net/mlx5e: Add TC drop and mirred/redirect action parsing for SRIOV offloads")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

This kind of action is not supported by firmware and generates a
syndrome.

kernel: mlx5_core 0000:08:00.0: mlx5_cmd_check:777:(pid 102063): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x8708c3)

Fixes: d7e75a32 ("net/mlx5e: Add offloading of E-Switch TC pedit (header re-write) actions")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

For RX TLS device-offloaded packets, the HW spec guarantees checksum
validation for the offloaded packets, but does not define whether the
CQE.checksum field matches the original packet (ciphertext) or
the decrypted one (plaintext). This latitude allows architetctural
improvements between generations of chips, resulting in different decisions
regarding the value type of CQE.checksum.

Hence, for these packets, the device driver should not make use of this CQE
field. Here we block CHECKSUM_COMPLETE usage for RX TLS device-offloaded
packets, and use CHECKSUM_UNNECESSARY instead.

Value of the packet's tcp_hdr.csum is not modified by the HW, and it always
matches the original ciphertext.

Fixes: 1182f365 ("net/mlx5e: kTLS, Add kTLS RX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The ioctl EEPROM query wrongly returns success on read failures, fix
that by returning the appropriate error code.

Fixes: bb64143e ("net/mlx5e: Add ethtool support for dump module EEPROM")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Add missing call to up_write_ref_node() which releases the semaphore
in case the FTE doesn't have destinations, such in drop rule case.

Fixes: 465e7baa ("net/mlx5: Fix deletion of duplicate rules")
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Only prio 1 is supported if firmware doesn't support ignore flow
level for nic mode. The offending commit removed the check wrongly.
Add it back.

Fixes: 9a99c8f1 ("net/mlx5e: E-Switch, Offload all chain 0 priorities when modify header and forward action is not supported")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Match metadata support check returns false for ecpf device.
However, this support does exist for ecpf and therefore this
limitation should be removed to allow feature such as stacked
devices and internal port offloaded to be supported.

Fixes: 92ab1eb3 ("net/mlx5: E-Switch, Enable vport metadata matching if firmware supports it")
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently, log_max_qp value is dependent on what FW reports as its max capability.
In reality, due to a bug, some FWs report a value greater than 17, even though they
don't support log_max_qp > 17.

This FW issue led the driver to exhaust memory on startup.
Thus, log_max_qp value is set to be no more than 17 regardless
of what FW reports, as it was before the cited commit.

Fixes: f79a609e ("net/mlx5: Update log_max_qp value to FW max capability")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Avihai Horon <avihaih@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

When deciding whether to start syncing and actually free all the "hot"
ICM chunks, we need to consider the type of the ICM chunks that we're
dealing with. For instance, the amount of available ICM for MODIFY_ACTION
is significantly lower than the usual STE ICM, so the threshold should
account for that - otherwise we can deplete MODIFY_ACTION memory just by
creating and deleting the same modify header action in a continuous loop.

This patch replaces the hard-coded threshold with a dynamic value.

Fixes: 1c586514 ("net/mlx5: DR, ICM memory pools sync optimization")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently SMFS allows adding rule with matching on src/dst IP w/o matching
on full ethertype or ip_version, which is not supported by HW.
This patch fixes this issue and adds the check as it is done in DMFS.

Fixes: 26d688e3 ("net/mlx5: DR, Add Steering entry (STE) utilities")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

When adding a rule with 32 destinations, we hit the following out-of-band
access issue:

  BUG: KASAN: slab-out-of-bounds in mlx5_cmd_dr_create_fte+0x18ee/0x1e70

This patch fixes the issue by both increasing the allocated buffers to
accommodate for the needed actions and by checking the number of actions
to prevent this issue when a rule with too many actions is provided.

Fixes: 1ffd4989 ("net/mlx5: DR, Increase supported num of actions to 32")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

During rule insertion on each ICM memory chunk we also allocate shadow memory
used for management. This includes the hw_ste, dr_ste and miss list per entry.
Since the scale of these allocations is large we noticed a performance hiccup
that happens once malloc and free are stressed.
In extreme usecases when ~1M chunks are freed at once, it might take up to 40
seconds to complete this, up to the point the kernel sees this as self-detected
stall on CPU:

 rcu: INFO: rcu_sched self-detected stall on CPU

To resolve this we will increase the reuse of shadow memory.
Doing this we see that a time in the aforementioned usecase dropped from ~40
seconds to ~8-10 seconds.

Fixes: 29cf8feb ("net/mlx5: DR, ICM pool memory allocator")
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Add the upcoming BlueField-4 and ConnectX-8 device IDs.

Fixes: 2e9d3e83 ("net/mlx5: Update the list of the PCI supported devices")
Signed-off-by: Meir Lichtinger <meirl@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Heyi Guo says:

====================
drivers/net/ftgmac100: fix occasional DHCP failure

This patch set is to fix the issues discussed in the mail thread:
https://lore.kernel.org/netdev/51f5b7a7-330f-6b3c-253d-10e45cdb6805@linux.alibaba.com/
and follows the advice from Andrew Lunn.

The first 2 patches refactors the code to enable adjust_link calling reset
function directly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

DHCP failures were observed with systemd 247.6. The issue could be
reproduced by rebooting Aspeed 2600 and then running ifconfig ethX
down/up.

It is caused by below procedures in the driver:

1. ftgmac100_open() enables net interface and call phy_start()
2. When PHY is link up, it calls netif_carrier_on() and then
adjust_link callback
3. ftgmac100_adjust_link() will schedule the reset task
4. ftgmac100_reset_task() will then reset the MAC in another schedule

After step 2, systemd will be notified to send DHCP discover packet,
while the packet might be corrupted by MAC reset operation in step 4.

Call ftgmac100_reset() directly instead of scheduling task to fix the
issue.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is to prepare for ftgmac100_adjust_link() to call
ftgmac100_reset() directly. Only code places are changed.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is to prepare for ftgmac100_adjust_link() to call reset function
directly, instead of task schedule.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix following coccicheck warning:
./net/sched/act_api.c:277:7-49: WARNING avoid newline at end of message
in NL_SET_ERR_MSG_MOD
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding myself (Alvin Šipraga) as another maintainer for the Realtek DSA
switch drivers. I intend to help Linus out with reviewing and testing
changes to these drivers, particularly the rtl8365mb driver which I
authored and have hardware access to.

Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

These tests are supposed to check if the loop exited via a break or not.
However the tests are wrong because if we did not exit via a break then
"p" is not a valid pointer.  In that case, it's the equivalent of
"if (*(u32 *)sr == *last_key) {".  That's going to work most of the time,
but there is a potential for those to be equal.

Fixes: 1593123a ("tipc: add name table dump to new netlink api")
Fixes: 1a1a143d ("tipc: add publication dump to new netlink api")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This test is checking if we exited the list via break or not.  However
if it did not exit via a break then "node" does not point to a valid
udp_tunnel_nic_shared_node struct.  It will work because of the way
the structs are laid out it's the equivalent of
"if (info->shared->udp_tunnel_nic_info != dev)" which will always be
true, but it's not the right way to test.

Fixes: 74cc6d18 ("udp_tunnel: add the ability to share port tables")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vhost_vsock_stop() calls vhost_dev_check_owner() to check the device
ownership. It expects current->mm to be valid.

vhost_vsock_stop() is also called by vhost_vsock_dev_release() when
the user has not done close(), so when we are in do_exit(). In this
case current->mm is invalid and we're releasing the device, so we
should clean it anyway.

Let's check the owner only when vhost_vsock_stop() is called
by an ioctl.

When invoked from release we can not fail so we don't check return
code of vhost_vsock_stop(). We need to stop vsock even if it's not
the owner.

Fixes: 433fc58e ("VSOCK: Introduce vhost_vsock.ko")
Cc: stable@vger.kernel.org
Reported-by: syzbot+1e3ea63db39f2b4440e0@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+3140b17cb44a7b174008@syzkaller.appspotmail.com
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If client is unable to initiate a failover reset via H_VIOCTL hcall, then
it should schedule a failover reset as a last resort. Otherwise, there is
no need to do a last resort.

Fixes: 334c4241 ("ibmvnic: improve failover sysfs entry")
Reported-by: Cris Forno <cforno12@outlook.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Link: https://lore.kernel.org/r/20220221210545.115283-1-drt@linux.ibm.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If a bridged port is not offloaded to the hardware - either because the
underlying driver does not implement the port_bridge_{join,leave} ops,
or because the operation failed - then its dp->bridge pointer will be
NULL when dsa_port_bridge_leave() is called. Avoid dereferncing NULL.

This fixes the following splat when removing a port from a bridge:

 Unable to handle kernel access to user memory outside uaccess routines at virtual address 0000000000000000
 Internal error: Oops: 96000004 [#1] PREEMPT_RT SMP
 CPU: 3 PID: 1119 Comm: brctl Tainted: G           O      5.17.0-rc4-rt4 #1
 Call trace:
  dsa_port_bridge_leave+0x8c/0x1e4
  dsa_slave_changeupper+0x40/0x170
  dsa_slave_netdevice_event+0x494/0x4d4
  notifier_call_chain+0x80/0xe0
  raw_notifier_call_chain+0x1c/0x24
  call_netdevice_notifiers_info+0x5c/0xac
  __netdev_upper_dev_unlink+0xa4/0x200
  netdev_upper_dev_unlink+0x38/0x60
  del_nbp+0x1b0/0x300
  br_del_if+0x38/0x114
  add_del_if+0x60/0xa0
  br_ioctl_stub+0x128/0x2dc
  br_ioctl_call+0x68/0xb0
  dev_ifsioc+0x390/0x554
  dev_ioctl+0x128/0x400
  sock_do_ioctl+0xb4/0xf4
  sock_ioctl+0x12c/0x4e0
  __arm64_sys_ioctl+0xa8/0xf0
  invoke_syscall+0x4c/0x110
  el0_svc_common.constprop.0+0x48/0xf0
  do_el0_svc+0x28/0x84
  el0_svc+0x1c/0x50
  el0t_64_sync_handler+0xa8/0xb0
  el0t_64_sync+0x17c/0x180
 Code: f9402f00 f0002261 f9401302 913cc021 (a9401404)
 ---[ end trace 0000000000000000 ]---

Fixes: d3eed0e5 ("net: dsa: keep the bridge_dev and bridge_num as part of the same structure")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220221203539.310690-1-alvin@pqrs.dkSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Whenever one of these functions pull all data from an skb in a frag_list,
use consume_skb() instead of kfree_skb() to avoid polluting drop
monitoring.

Fixes: 6fa01ccd ("skbuff: Add pskb_extract() helper function")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220220154052.1308469-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

This is fixing up the use without proper initialization in patch 5/5

-o-

Hi,

The following patchset contains Netfilter fixes for net:

1) Missing #ifdef CONFIG_IP6_NF_IPTABLES in recent xt_socket fix.

2) Fix incorrect flow action array size in nf_tables.

3) Unregister flowtable hooks from netns exit path.

4) Fix missing limit object release, from Florian Westphal.

5) Memleak in nf_tables object update path, also from Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

stateful objects can be updated from the control plane.
The transaction logic allocates a temporary object for this purpose.

The ->init function was called for this object, so plain kfree() leaks
resources. We must call ->destroy function of the object.

nft_obj_destroy does this, but it also decrements the module refcount,
but the update path doesn't increment it.

To avoid special-casing the update object release, do module_get for
the update case too and release it via nft_obj_destroy().

Fixes: d62d0ba9 ("netfilter: nf_tables: Introduce stateful object update operation")
Cc: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

We need to provide a destroy callback to release the extra fields.

Fixes: 3b9e2ea6 ("netfilter: nft_limit: move stateful fields out of expression data")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Unregister flowtable hooks before they are releases via
nf_tables_flowtable_destroy() otherwise hook core reports UAF.

BUG: KASAN: use-after-free in nf_hook_entries_grow+0x5a7/0x700 net/netfilter/core.c:142 net/netfilter/core.c:142
Read of size 4 at addr ffff8880736f7438 by task syz-executor579/3666

CPU: 0 PID: 3666 Comm: syz-executor579 Not tainted 5.16.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 <TASK>
 __dump_stack lib/dump_stack.c:88 [inline]
 __dump_stack lib/dump_stack.c:88 [inline] lib/dump_stack.c:106
 dump_stack_lvl+0x1dc/0x2d8 lib/dump_stack.c:106 lib/dump_stack.c:106
 print_address_description+0x65/0x380 mm/kasan/report.c:247 mm/kasan/report.c:247
 __kasan_report mm/kasan/report.c:433 [inline]
 __kasan_report mm/kasan/report.c:433 [inline] mm/kasan/report.c:450
 kasan_report+0x19a/0x1f0 mm/kasan/report.c:450 mm/kasan/report.c:450
 nf_hook_entries_grow+0x5a7/0x700 net/netfilter/core.c:142 net/netfilter/core.c:142
 __nf_register_net_hook+0x27e/0x8d0 net/netfilter/core.c:429 net/netfilter/core.c:429
 nf_register_net_hook+0xaa/0x180 net/netfilter/core.c:571 net/netfilter/core.c:571
 nft_register_flowtable_net_hooks+0x3c5/0x730 net/netfilter/nf_tables_api.c:7232 net/netfilter/nf_tables_api.c:7232
 nf_tables_newflowtable+0x2022/0x2cf0 net/netfilter/nf_tables_api.c:7430 net/netfilter/nf_tables_api.c:7430
 nfnetlink_rcv_batch net/netfilter/nfnetlink.c:513 [inline]
 nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:634 [inline]
 nfnetlink_rcv_batch net/netfilter/nfnetlink.c:513 [inline] net/netfilter/nfnetlink.c:652
 nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:634 [inline] net/netfilter/nfnetlink.c:652
 nfnetlink_rcv+0x10e6/0x2550 net/netfilter/nfnetlink.c:652 net/netfilter/nfnetlink.c:652

__nft_release_hook() calls nft_unregister_flowtable_net_hooks() which
only unregisters the hooks, then after RCU grace period, it is
guaranteed that no packets add new entries to the flowtable (no flow
offload rules and flowtable hooks are reachable from packet path), so it
is safe to call nf_flow_table_free() which cleans up the remaining
entries from the flowtable (both software and hardware) and it unbinds
the flow_block.

Fixes: ff4bf2f4 ("netfilter: nf_tables: add nft_unregister_flowtable_hook()")
Reported-by: syzbot+e918523f77e62790d6d9@syzkaller.appspotmail.com
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Experimentation shows that PHY detect might fail when the code attempts
MDIO bus read immediately after clock enable. Add delay to stabilize the
clock before bus access.

PHY detect failure started to show after commit 7590fc6f ("net:
mdio: Demote probed message to debug print") that removed coincidental
delay between clock enable and bus access.

10ms is meant to match the time it take to send the probed message over
UART at 115200 bps. This might be a far overshoot.

Fixes: 23a890d4 ("net: mdio: Add the reset function for IPQ MDIO driver")
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

We encounter a tcp drop issue in our cloud environment. Packet GROed in
host forwards to a VM virtio_net nic with net_failover enabled. VM acts
as a IPVS LB with ipip encapsulation. The full path like:
host gro -> vm virtio_net rx -> net_failover rx -> ipvs fullnat
 -> ipip encap -> net_failover tx -> virtio_net tx

When net_failover transmits a ipip pkt (gso_type = 0x0103, which means
SKB_GSO_TCPV4, SKB_GSO_DODGY and SKB_GSO_IPXIP4), there is no gso
did because it supports TSO and GSO_IPXIP4. But network_header points to
inner ip header.

Call Trace:
 tcp4_gso_segment        ------> return NULL
 inet_gso_segment        ------> inner iph, network_header points to
 ipip_gso_segment
 inet_gso_segment        ------> outer iph
 skb_mac_gso_segment

Afterwards virtio_net transmits the pkt, only inner ip header is modified.
And the outer one just keeps unchanged. The pkt will be dropped in remote
host.

Call Trace:
 inet_gso_segment        ------> inner iph, outer iph is skipped
 skb_mac_gso_segment
 __skb_gso_segment
 validate_xmit_skb
 validate_xmit_skb_list
 sch_direct_xmit
 __qdisc_run
 __dev_queue_xmit        ------> virtio_net
 dev_hard_start_xmit
 __dev_queue_xmit        ------> net_failover
 ip_finish_output2
 ip_output
 iptunnel_xmit
 ip_tunnel_xmit
 ipip_tunnel_xmit        ------> ipip
 dev_hard_start_xmit
 __dev_queue_xmit
 ip_finish_output2
 ip_output
 ip_forward
 ip_rcv
 __netif_receive_skb_one_core
 netif_receive_skb_internal
 napi_gro_receive
 receive_buf
 virtnet_poll
 net_rx_action

The root cause of this issue is specific with the rare combination of
SKB_GSO_DODGY and a tunnel device that adds an SKB_GSO_ tunnel option.
SKB_GSO_DODGY is set from external virtio_net. We need to reset network
header when callbacks.gso_segment() returns NULL.

This patch also includes ipv6_gso_segment(), considering SIT, etc.

Fixes: cb32f511 ("ipip: add GSO/TSO support")
Signed-off-by: Tao Liu <thomas.liu@ucloud.cn>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Bug fixes

This series contains bug fixes for FEC reporting, ethtool self test,
multicast setup, devlink health reporting and live patching, and
a firmware response timeout.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

To install a livepatch, first flash the package to NVM, and then
activate the patch through the "HWRM_FW_LIVEPATCH" fw command.
To uninstall a patch from NVM, flash the removal package and then
activate it through the "HWRM_FW_LIVEPATCH" fw command.

The "HWRM_FW_LIVEPATCH" fw command has to consider following scenarios:

1. no patch in NVM and no patch active. Do nothing.
2. patch in NVM, but not active. Activate the patch currently in NVM.
3. patch is not in NVM, but active. Deactivate the patch.
4. patch in NVM and the patch active. Do nothing.

Fix the code to handle these scenarios during devlink "fw_activate".

To install and activate a live patch:
devlink dev flash pci/0000:c1:00.0 file thor_patch.pkg
devlink -f dev reload pci/0000:c1:00.0 action fw_activate limit no_reset

To remove and deactivate a live patch:
devlink dev flash pci/0000:c1:00.0 file thor_patch_rem.pkg
devlink -f dev reload pci/0000:c1:00.0 action fw_activate limit no_reset

Fixes: 3c415339 ("bnxt_en: implement firmware live patching")
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When polling for the firmware message response, we first poll for the
response message header.  Once the valid length is detected in the
header, we poll for the valid bit at the end of the message which
signals DMA completion.  Normally, this poll time for DMA completion
is extremely short (0 to a few usec).  But on some devices under some
rare conditions, it can be up to about 20 msec.

Increase this delay to 50 msec and use udelay() for the first 10 usec
for the common case, and usleep_range() beyond that.

Also, change the error message to include the above delay time when
printing the timeout value.

Fixes: 3c8c20db ("bnxt_en: move HWRM API implementation into separate file")
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During ifdown, we call bnxt_inv_fw_health_reg() which will clear
both the status_reliable and resets_reliable flags if these
registers are mapped.  This is correct because a FW reset during
ifdown will clear these register mappings.  If we detect that FW
has gone through reset during the next ifup, we will remap these
registers.

But during normal ifup with no FW reset, we need to restore the
resets_reliable flag otherwise we will not show the reset counter
during devlink diagnose.

Fixes: 8cc95ceb ("bnxt_en: improve fw diagnose devlink health messages")
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should setup multicast only when net_device flags explicitly
has IFF_MULTICAST set. Otherwise we will incorrectly turn it on
even when not asked.  Fix it by only passing the multicast table
to the firmware if IFF_MULTICAST is set.

Fixes: 7d2837dd ("bnxt_en: Setup multicast properly after resetting device.")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the current code, we setup the port to PHY or MAC loopback mode
and then transmit a test broadcast packet for the loopback test.  This
scheme fails sometime if the port is shared with management firmware
that can also send packets.  The driver may receive the management
firmware's packet and the test will fail when the contents don't
match the test packet.

Change the test packet to use it's own MAC address as the destination
and setup the port to only receive it's own MAC address.  This should
filter out other packets sent by management firmware.

Fixes: 91725d89 ("bnxt_en: Add PHY loopback to ethtool self-test.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>