Print the function name in which MPT command got timed out. This will
facilitate debugging in which path corresponding MPT command got timeout in
first failure instance of log itself.

Link: https://lore.kernel.org/r/20191226111333.26131-9-sreekanth.reddy@broadcom.comSigned-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This improves mpt3sas driver default debug information collection and
allows for a higher percentage of issues being able to be resolved with a
first-time data capture.  However, this improvement to balance the amount
of debug data captured with the performance of driver.

Enabled below print messages with out affecting the IO performance,

1. When task abort TM is received then print IO commands's timeout value
   and how much time this command has been outstanding.

2. Whenever hard reset occurs then print from where this hard reset has
   been issued.

3. Failure message should be displayed for failure scenarios without any
   logging level.

4. Added a print after driver successfully register or unregistered a
   target drive with the SML. This print will be useful for debugging the
   issue where the drive addition or deletion is hanging at SML.

5. During driver load time print request, reply, sense and config page
   pool's information such as its address, length and size. Also printed
   sg_tablesize information.

Link: https://lore.kernel.org/r/20191226111333.26131-8-sreekanth.reddy@broadcom.comSigned-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

When Firmware fault occurs then print in which path firmware fault has
occurred. This will be useful while debugging the firmware fault issues.

Link: https://lore.kernel.org/r/20191226111333.26131-7-sreekanth.reddy@broadcom.comSigned-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Watchdog thread polls for IOC state every 1 second.  If it detects that IOC
state is in CoreDump state then it immediately stops the IOs and also
clears the outstanding commands issued to the HBA firmware and then it will
poll for IOC state to be out of CoreDump state and once it detects that IOC
state is changed from CoreDump state to Fault state (or) CoreDumpTOSec
number of seconds are elapsed then it will issue host reset operation and
moves the IOC state to Operational state and resumes the IOs.

Whenever any TM is received from SML then if driver detects the IOC state
is in CoreDump state then it will wait for CoreDump state to be cleared and
will host reset operation.

Link: https://lore.kernel.org/r/20191226111333.26131-6-sreekanth.reddy@broadcom.comSigned-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

New feature is added in HBA firmware where it copies the collected firmware
logs in flash region named 'CoreDump' whenever HBA firmware faults occur.

For copying the logs to CoreDump flash region firmware needs some time and
hence it has introduced a new IOC state named "CoreDump" State.

Whenever driver detects the CoreDump state then it means that some firmware
fault has occurred and firmware is copying the logs to the coredump flash
region. During this time driver should not perform any operation with the
HBA, driver should wait for HBA firmware to move the IOC state from
'CoreDump' state to 'Fault' state once it's done with copying the logs to
coredump region. Once driver detects the Fault state then it will issue the
diag reset/host reset operation to move the IOC state from Fault to
Operational state.

Here the valid IOC state transactions w.r.t to this CoreDump state feature,

Operational -> Fault:
The IOC transitions to the Fault state when an operational error occurs AND
CoreDump is not supported (or disabled) by the firmware(FW).

Operational -> CoreDump:
The IOC transitions to the CoreDump state when an operational error occurs
AND CoreDump is supported & enabled by the FW.

CoreDump -> Fault:
A transition from CoreDump state to Fault state happens when the FW
completes the CoreDump collection.

CoreDump -> Reset:
A transition out of the CoreDump state happens when the host sets the Reset
Adapter bit in the System Diagnostic Register (Hard Reset). This reset
action indicates that CoreDump took longer than the host time out.

Firmware informs the driver about the maximum time that driver has to wait
for firmware to transition the IOC state from 'CoreDump' to 'FAULT' state
through 'CoreDumpTOSec' field of ManufacturingPage11 page. if this
'CoreDumpTOSec' field value is zero then driver will wait for max 15
seconds.

Driver informs the HBA firmware that it supports this new IOC state named
'CoreDump' state by enabling COREDUMP_ENABLE flag in ConfigurationFlags
field of ioc init request message.

Current patch handles the CoreDump state only during HBA initialization and
release scenarios where watchdog thread (which polls the IOC state in every
one second) is disabled.  Next subsequent patch handle the CoreDump state
when watchdog thread is enabled.

During HBA initialization or release execution time if driver detects the
CoreDump state then driver will wait for maximum CoreDumpTOSec value
seconds for FW to copy the logs. After that it will issue the diag reset
operation to move the IOC state to Operational state.

Link: https://lore.kernel.org/r/20191226111333.26131-5-sreekanth.reddy@broadcom.comSigned-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Renamed _base_after_reset_handler function to
_base_clear_outstanding_commands so that it can be used in multiple
scenarios with suitable name which matches with the operation it does.

Also renamed its child functions. No functional changes.

Link: https://lore.kernel.org/r/20191226111333.26131-4-sreekanth.reddy@broadcom.comSigned-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Introduce function _scsih_nvme_shutdown() to issue IO Unit Control message
to IOC firmware with operation code 'shutdown'. This causes IOC firmware to
issue NVMe shutdown commands to all NVMe drives attached to it.

NVMe Shutdown:

NVMe devices need to have a specific shutdown sequence performed before
power is removed. For this, the IOC firmware needs to be notified when the
system is being shutdown. So during the system shutdown time, driver issues
an IO Unit Control request with operation code MPI26_CTRL_OP_SHUTDOWN to
inform firmware that a shutdown is initiated.

This shutdown command is issued only if NVMe devices are attached to the
controller.

During each NVMe device addition, driver reads pcie device page2 to get
shutdown latency (e.g. drive's RTD3 Entry Latency) and updates the max
latency value among the added NVMe drives in ioc->max_shutdown_latency.
This is used as the timeout value for IO Unit Control command at the time
of shutdown.

When a NVMe drive is removed and its shutdown latency matches which
ioc->max_shutdown_latency then ioc->max_shutdown_latency is updated to next
max value (by iterating over the list of available devices).  If the
shutdown latency is 0, then default timeout is set to six seconds.

Link: https://lore.kernel.org/r/20191226111333.26131-3-sreekanth.reddy@broadcom.comSigned-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Update MPI Headers to version 02.00.57.

Link: https://lore.kernel.org/r/20191226111333.26131-2-sreekanth.reddy@broadcom.comSigned-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Enable clk-gating with customized delayed timer value in MediaTek Chipsets.

Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1577683950-1702-7-git-send-email-stanley.chu@mediatek.comReviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Configure customized auto-hibern8 timer in MediaTek Chipsets.

Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1577683950-1702-6-git-send-email-stanley.chu@mediatek.comReviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Export ufshcd_auto_hibern8_update to allow vendors to use common interface
to customize auto-hibernate timer.

Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1577683950-1702-5-git-send-email-stanley.chu@mediatek.comReviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Introduce reference clock control in MediaTek Chipset in order to disable
it if it is not necessary by UFS device to save system power.

Currently reference clock can be disabled during system suspend, runtime
suspend and clock-gating after link enters hibernate state.

Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1577683950-1702-4-git-send-email-stanley.chu@mediatek.comReviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Add device reset vops implementation in MediaTek UFS driver.

Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1577683950-1702-3-git-send-email-stanley.chu@mediatek.comReviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Add a common header for the SiP service interface in MediaTek Chipsets.

Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1577683950-1702-2-git-send-email-stanley.chu@mediatek.comSigned-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This patch corrects the SPDX License Identifier style in header file
related to UFS Host Controller. It assigns explicit block comment to the
SPDX License Identifier.

Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.

Link: https://lore.kernel.org/r/5ca6287665fe52d8f40062e0eab8561d2b7a5b40.1577511720.git.nishadkamdar@gmail.comSuggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This patch corrects the SPDX License Identifier style in header files
related to Mylex DAC960/DAC1100 PCI RAID Controllers. It assigns explicit
block comment to the SPDX License Identifier.

Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.

Link: https://lore.kernel.org/r/88332ad390f985bdebb9f2adaf2d499b0a639753.1577511720.git.nishadkamdar@gmail.comSuggested-by: Joe Perches <joe@perches.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The UFS SCSI timeout handler was needed to compensate that
ufshcd_queuecommand() could return SCSI_MLQUEUE_HOST_BUSY for a long
time. Commit a276c19e3e98 ("scsi: ufs: Avoid busy-waiting by eliminating
tag conflicts") fixed this so the timeout handler is no longer necessary.

See also commit f550c65b ("scsi: ufs: implement scsi host timeout handler").

Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20191224220248.30138-7-bvanassche@acm.orgReviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Starting execution of a command before tracing a command may cause the
completion handler to free data while it is being traced. Fix this race by
tracing a command before it is submitted.

Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20191224220248.30138-5-bvanassche@acm.orgReviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Since the lrbp->cmd expression occurs multiple times, introduce a new local
variable to hold that pointer. This patch does not change any
functionality.

Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20191224220248.30138-4-bvanassche@acm.orgReviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Since the lrbp->cmd expression occurs multiple times, introduce a new local
variable to hold that pointer. This patch does not change any
functionality.

Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20191224220248.30138-3-bvanassche@acm.orgReviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Remove a space that occurs after a tab.

Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20191224220248.30138-2-bvanassche@acm.orgReviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Alim Akhar <alim.akhtar@samsung.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

We already have ufshcd_vops_dbg_register_dump() thus all
"hba->vops->dbg_register_dump" references can be replaced by it.

Link: https://lore.kernel.org/r/1577192466-20762-3-git-send-email-stanley.chu@mediatek.comReviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Currently UFS driver has ufshcd_scsi_block_requests() with reference
counter mechanism to avoid possible racing of blocking and unblocking
requests flow. Unify all users in UFS driver to use the same function.

Link: https://lore.kernel.org/r/1577192466-20762-2-git-send-email-stanley.chu@mediatek.comReviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Now that the block layer implement zone checks on revalidate,
sd_zbc_check_zones() is reduced getting the zone size and verifying the
device capacity for device with RC_BASIS=0. Be clear about this by renaming
sd_zbc_check_zones() to sd_zbc_check_capacity() and updating the function
description and comments.

Link: https://lore.kernel.org/r/20191220075823.400072-3-damien.lemoal@wdc.comSigned-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Now that the block layer generic zone revalidation code in
blk_revalidate_disk_zones() checks for power of 2 zone size, there is no
need to do it in sd_zbc_check_zones(). Remove this check.

Link: https://lore.kernel.org/r/20191220075823.400072-2-damien.lemoal@wdc.comSigned-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This patch improves readability and does not change any functionality.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Daniel Wagner <dwagner@suse.de>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Link: https://lore.kernel.org/r/20191219005050.40193-1-bvanassche@acm.orgReviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Since qla82xx_get_fw_size() returns a number in CPU-endian format, change
its return type from __le32 into u32. This patch does not change any
functionality.

Fixes: 9c2b2975 ("[SCSI] qla2xxx: Support for loading Unified ROM Image (URI) format firmware file.")
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Daniel Wagner <dwagner@suse.de>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Link: https://lore.kernel.org/r/20191219004905.39586-1-bvanassche@acm.orgReviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Declare qla_hw_data.flt as a qla_flt_header pointer instead of as a void
pointer. Add a zero-length array at the end of struct qla_flt_header to
make it clear that qla_flt_header and qla_flt_region are contiguous. This
patch removes several casts but does not change any functionality.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Daniel Wagner <dwagner@suse.de>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Link: https://lore.kernel.org/r/20191219004706.39039-1-bvanassche@acm.orgReviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Currently we use a mixture of %016llx, %llx, and %16llx when printing a SAS
address.

Since the most significant nibble of the SAS address is always 5 - as per
standard - this formatting is not so important; but some fake SAS addresses
for SATA devices may not be. And we have mangled/invalid address to
consider also. And it's better to be consistent in the code, so use a fixed
format.

The SAS address is a fixed size at 64b, so we want to 0 byte extend to 16
nibbles, so use %016llx globally.

Also make some prints to be explicitly hex, and tidy some whitespace issue.

Link: https://lore.kernel.org/r/1576758957-227350-1-git-send-email-john.garry@huawei.comSigned-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Update lpfc version to 12.6.0.3

Link: https://lore.kernel.org/r/20191218235808.31922-11-jsmart2021@gmail.comSigned-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Current driver code looks at iocb types and uses a "==" comparison on the
flags to determine type. If another flag were set, it would disrupt the
comparison.

Fix by converting to a bitwise & operation.

Link: https://lore.kernel.org/r/20191218235808.31922-10-jsmart2021@gmail.comSigned-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

When running Cisco-MDS diagnostics which perform driver-level frame loop
back, the switch is reporting errors. Diagnostic has a limit on latency
that is not being met by the driver.

The requirement of Latency frames is that they should be responded back by
the host with a maximum delay of few hundreds of microseconds. If the
switch doesn't get response frames within this time frame, it fails the
test.

Test is failing as the lpfc-wq workqueue was overwhelmed by the packet rate
and in some cases, the work element yielded to other kernel elements.

To resolve, reduce the outstanding load allowed by the adapter. This
ensures the driver spends a reasonable amount of time doing loopback and
can do so such that latency values can be met.  Load is managed by reducing
the number of receive buffers posted such that the link can be
backpressured to reduce load.

Link: https://lore.kernel.org/r/20191218235808.31922-9-jsmart2021@gmail.comSigned-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

When unattaching, the driver did not unmap the DPP bar. This caused the
next load of the driver, which attempts to enable wc, to not work correctly
and wc to be disabled due to an address mapping overlap.

Fix by unmapping on unattach.

Link: https://lore.kernel.org/r/20191218235808.31922-8-jsmart2021@gmail.comSigned-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The order of the flags/checks for adapters where FC-AL is supported
erroneously excluded lpe35000 adapter models.  Also noted that the G7 flags
for Loop and Persistent topology are incorrect. They should follow the
rules as G6.

Rework the logic to enable LPe35000 FC-AL support.  Collapse G7 support
logic to the same rules as G6.

Link: https://lore.kernel.org/r/20191218235808.31922-7-jsmart2021@gmail.comSigned-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

/sys/kernel/debug/lpfc/fn0/ras_log always shows the same ras_log even if
there are link bounce events triggered via issue_lip

Dynamic FW logging had logic that prematurely breaks from the buffer
filling loop.

Fix the check for buffer overrun by looking before copying and restricting
copy length to the remaining buffer.  When copying, ensure space for NULL
character is left in the buffer.  While in the routine - ensure the buffer
is cleared before adding elements.

Link: https://lore.kernel.org/r/20191218235808.31922-6-jsmart2021@gmail.comSigned-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

There are reports of multiple ports on the same system displaying different
hostnames in fabric FDMI displays.

Currently, the driver registers the hostname at initialization and obtains
the hostname via init_utsname()->nodename queried at the time the FC link
comes up. Unfortunately, if the machine hostname is updated after
initialization, such as via DHCP or admin command, the value registered
initially will be incorrect.

Fix by having the driver save the hostname that was registered with FDMI.
The driver then runs a heartbeat action that will check the hostname.  If
the name changes, reregister the FMDI data.

The hostname is used in RSNN_NN, FDMI RPA and FDMI RHBA.

Link: https://lore.kernel.org/r/20191218235808.31922-5-jsmart2021@gmail.comSigned-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

When the WriteObject mailbox response has change_status set to is 0x2
(Firmware Reset) or 0x04 (Port Migration Reset), the CSF field should also
be checked to see if a fw reset is sufficient to enable all new features in
the updated firmware image. If not, a fw reset would start the new
firmware, but with a feature level equal to existing firmware.  To enable
the new features, a chip reset/pci slot reset would be required.

Check the CSF bit when change_status is 0x2 or 0x4 to know whether to
perform a pci bus reset or fw reset.

Link: https://lore.kernel.org/r/20191218235808.31922-4-jsmart2021@gmail.comSigned-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This patch reworks the fdmi symbolic node name data for the following two
issues:

 - Correcting extraneous periods following the DV and HN fdmi data fields.

 - Avoiding buffer overflow issues when formatting the data.

The fix to the fist issue is to just remove the characters.

The fix to the second issue has all data being staged in temporary storage
before being moved to the real buffer.

Link: https://lore.kernel.org/r/20191218235808.31922-3-jsmart2021@gmail.comSigned-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

NVMe device re-discovery does not complete. Dev_loss_tmo messages seen on
initiator after recovery from a link disturbance.

The failing case is the following:

When the driver (as a NVME target) receives a PLOGI, the driver initiates
an "unreg rpi" mailbox command. While the mailbox command is in progress,
the driver requests that an ACC be sent to the initiator. The target's ACC
is received by the initiator and the initiator then transmits a PLOGI. The
driver receives the PLOGI prior to receiving the completion for the PLOGI
response WQE that sent the ACC. (Different delivery sources from the hw so
the race is very possible). Given the PLOGI is prior to the ACC completion
(signifying PLOGI exchange complete), the driver LS_RJT's the PRLI. The
"unreg rpi" mailbox then completes. Since PRLI has been received, the
driver transmits a PLOGI to restart discovery, which the initiator then
ACC's.  If the driver processes the (re)PLOGI ACC prior to the completing
the handling for the earlier ACC it sent the intiators original PLOGI,
there is no state change for completion of the (re)PLOGI. The ndlp remains
in "PLOGI Sent" and the initiator continues sending PRLI's which are
rejected by the target until timeout or retry is reached.

Fix by: When in target mode, defer sending an ACC for the received PLOGI
until unreg RPI completes.

Link: https://lore.kernel.org/r/20191218235808.31922-2-jsmart2021@gmail.comSigned-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Link: https://lore.kernel.org/r/20191217220617.28084-15-hmadhani@marvell.comSigned-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>