This patch adds bindings for r8a77990 (R-Car E3).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Document RZ/G2M (R8A774A1) SoC bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

If the "workaround_for_vbus" is true, the driver will not call
usb_disconnect(). So, since the controller keeps some registers'
value, the driver doesn't re-enumarate suitable speed after
the b-device mode is disabled. To fix the issue, this patch
adds usb_disconnect() calling in renesas_usb3_b_device_write()
if workaround_for_vbus is true.

Fixes: 43ba968b ("usb: gadget: udc: renesas_usb3: add debugfs to set the b-device mode")
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Added interrupt handler for WkupAlert interrupt.

This interrupt should initiate Remote Wake up.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

WKUP_ALERT interrupt should be unmask when lpm mode is enabled.

This interrupt is asserted when the device is in L1 for the duration
mentioned in GREFCLK.SOF_CNN_WKUP_ALERT. This is used to alert SW to
initiate Remote wake up so that the device resumes in time in order not
to lose sync with the host frame number.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Added dwc2_gadget_program_ref_clk function to program GREFCLK
register in device mode.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Added ref_clk_per and sof_cnt_wkup_alert parameters in
dwc2_core_params struct and set default values.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

New registers were added to dwc otg core.

GREFCLK - This register used to control ref_clk parameters.

GINTSTS2 - New WKUP_ALERT interrupt was added.

GINTMSK2 - Mask register for GINTSTS2.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In service interval based scheduling target (u)frame must be
set as a last frame in this the service interval.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Added dwc2_gadget_dec_frame_num_by_one() function in gadget.c.
This function will be used to calculate descriptor frame number field
value. For service interval mode frame number in descriptor should point
to last (u)frame in the interval.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Added core parameter for service interval based scheduling.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Added GHWCFG4_SERVICE_INTERVAL_SUPPORTED and
DCTL_SERVICE_INTERVAL_SUPPORTED bits definitions to support
service interval based scheduling.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds support for R-Car E3. This SoC needs to release
the PLL reset by the UGCTRL register like R-Car D3. So, this patch
adds a usbhs_of_match entry for this SoC with
"USBHS_TYPE_RCAR_GEN3_WITH_PLL".
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds bindings for r8a77990 (R-Car E3).
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Since R-Car D3 can use OTG mode, this patch changes the UGCTRL2
value to UGCTRL2_USB0SEL_OTG and UGCTRL2_VBUSSEL like other R-Car
Gen3 SoCs.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This reverts commit cd14247d.

R-Car D3 can use OTG mode in fact. So, the commit doesn't need anymore.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Via p_chmask/c_chmask the user can define whether uac2 shall support
playback and/or capture. This has only effect on the created ALSA device,
but not on the USB descriptor. This patch adds playback/capture descriptors
dependent on that parameter.
Signed-off-by: Andreas Pape <apape@de.adit-jv.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The gadget documentation doesn't state clearly whether a gadget
driver's ->disconnect() callback should be invoked when the D+ pullup
is turned off.  Some UDC drivers do this and some don't.  This patch
settles the issue by making the core function usb_gadget_disconnect()
issue the callback, so that UDC drivers don't need to worry about it.

A description of the new behavior is added to the function's
kerneldoc.  Also, the patch removes a few superseded callbacks from
other core routines.

Future patches will remove the ->disconnect() calls from the UDC
drivers that make them, as they are now unnecessary.  Until all those
patches are merged gadget drivers may receive extra ->disconnect()
callbacks, but this should be harmless.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

'optimizations' was misspelled as 'optmizations'. Fixed it. It is a
coding style change which should have no impact on runtime execution of code.
Signed-off-by: Faisal Mehmood <f.m3hm00d@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The name is always non-NULL and then is not used anywhere in this function,
so remove it.

Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-usb@vger.kernel.org
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The original implementation from commit b504882d
("USB: add Freescale high-speed USB SOC device controller driver")
returned NULL on failure and an allocated + initialized struct fsl_udc on
success. The current code introduced in commit 4365831d
("USB: fsl_usb2_udc: Get max ep number from DCCPARAMS register") only
provides partial initialization as well as returning 0 on success and -1
on failures. The function documentation is updated accordingly.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 4365831d ("USB: fsl_usb2_udc: Get max ep number from DCCPARAMS register")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The allocation with fsl_alloc_request() and kmalloc() were unchecked
fixed this up with a NULL check and appropriate cleanup.

Additionally udc->ep_qh_size was reset to 0 on failure of allocation.
Similar udc->phy_mode is initially 0 (as udc_controller was
allocated with kzalloc in fsl_udc_probe()) so reset it to 0 as well
so that this function is side-effect free on failure. Not clear if
this is necessary or sensible as fsl_udc_release() probably can not
be called if fsl_udc_probe() failed - but it should not hurt.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: b504882d ("USB: add Freescale high-speed USB SOC device controller driver")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The vbus rise & fall interrupts are used to enable and disable
U3 function of device automatically, this cause some issues when
class driver is initialized as deactivated, and will skip over
software-controlled connect by pullup(), but UDC wants to keep
disconnect until usb_gadget_activate() is called which calls
pullup() if needed. So we disable vbus rise & fall interrupts
and just use pullup() to enable & disable U3 function, and reset
mtu3 state when disconnect instead when vbus fall.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

R-Car Gen3 needs to enable clocks of both host and peripheral.
Since [eo]hci-platform disables the reset(s) when the drivers are
removed, renesas_usbhs driver doesn't work correctly. To fix this
issue, this patch adds multiple clocks management on this
renesas_usbhs driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

R-Car Gen3 needs to enable clocks of both host and peripheral.
Otherwise, other side device cannot work correctly. So, this patch
adds a property of clock-names for R-Car Gen3 as an optional.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

R-Car Gen3 needs to deassert resets of both host and peripheral.
Since [eo]hci-platform is possible to assert the reset(s) when
the probing failed, renesas_usbhs driver doesn't work correctly
regardless of finished probing. To fix this issue, this patch adds
reset_control on this renesas_usbhs driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When operating in USB 2.0 speeds (HS/FS), if GUSB2PHYCFG.ENBLSLPM or
GUSB2PHYCFG.SUSPHY is set, it must be cleared before issuing an endpoint
command.

Current implementation only save and restore GUSB2PHYCFG.SUSPHY
configuration. We must save and clear both GUSB2PHYCFG.ENBLSLPM and
GUSB2PHYCFG.SUSPHY settings. Restore them after the command is
completed.

DWC_usb3 3.30a and DWC_usb31 1.90a programming guide section 3.2.2
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When using external vbus supply regulator, it should be enabled
synchronously with PWR bit in HPRT register. This also fixes
unbalanced use of this optional regulator (This can be reproduced
easily when unbinding the driver).

Fixes: 531ef5eb ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

dwc2_vbus_supply_exit() may call regulator_disable(). It shouldn't be
called with interrupts disabled as it might sleep.
This is seen with DEBUG_ATOMIC_SLEEP=y.

Fixes: 531ef5eb ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

There's a race with root hub resume, when using external vbus supply.
Root hub gets resumed, but runtime pm autosuspend runs as external vbus
supply isn't enabled. So, host never exit from power down properly.
Initialize vbus external supply before, rater that after hub resume.

Fixes: 531ef5eb ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Move devm_regulator_get_optional() call to probe routine. This avoids
'vbus-supply' regulator to be requested lots of times, upon each call
to dwc2_vbus_supply_init(), e.g. like with runtime pm.

Fixes: 531ef5eb ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Like the omap back-end, we get a link error with CONFIG_EXTCON=m
when building the qcom back-end into the kernel:

drivers/usb/dwc3/dwc3-qcom.o: In function `dwc3_qcom_probe':
dwc3-qcom.c:(.text+0x13dc): undefined reference to `extcon_get_edev_by_phandle'
dwc3-qcom.c:(.text+0x1b18): undefined reference to `devm_extcon_register_notifier'
dwc3-qcom.c:(.text+0x1b9c): undefined reference to `extcon_get_state'

Do the same thing as OMAP and add an explicit dependency on
EXTCON.

Fixes: a4333c3a ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The at91sam9rl PMC is not quite the same as the at91sam9g45 one and now has
its own compatible string. Add support for that.

Fixes: 217bace8e548 ("ARM: dts: fix PMC compatible")
Acked-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The driver may sleep in an interrupt handler.
The function call path (from bottom to top) in Linux-4.17 is:

[FUNC] fotg210_ep_queue(GFP_KERNEL)
drivers/usb/gadget/udc/fotg210-udc.c, 744:
	fotg210_ep_queue in fotg210_get_status
drivers/usb/gadget/udc/fotg210-udc.c, 768:
	fotg210_get_status in fotg210_setup_packet
drivers/usb/gadget/udc/fotg210-udc.c, 949:
	fotg210_setup_packet in fotg210_irq (interrupt handler)

To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC.
If possible, spin_unlock() and spin_lock() around fotg210_ep_queue()
can be also removed.

This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Disabling all EP's allow to reset EP's to initial state.
On disconnect disable all EP's instead of just killing
all requests. Because of some platform didn't catch
disconnect event, same stuff added to
dwc2_hsotg_core_init_disconnected() function when USB
reset detected on the bus.

Changed from version 1:
Changed lock acquire flow in dwc2_hsotg_ep_disable()
function.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

DWC3 variant found in Exynos5433 SoCs requires keeping all DRD30/UHOST30
clocks enabled all the time the driver does any access to DWC3 registers,
otherwise external abort happens. So far DWC3 hardware module worked with
samsung,exynos5250-dwusb3 compatible only by luck when built into kernel:
all DRD30 clocks were left enabled by bootloader and later kept enabled
by the DRD PHY driver. However, if one tried to use Exnos DWC3 driver as
a module or performed system suspend/resume cycle, external abort
happened. This patch finally fixes this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add per-variant list of clocks and manage them all together in
the single array. This is a preparation for adding new variants
of Exynos SoCs. No functional changes for existing Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

All supported Exynos variants provide respective generic PHY framework
based drivers for controlling USB PHYs, so there is no point
creating fake USB PHYs based on platform devices. While removing useless
code, remove calls to runtime PM, which have no effect.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Trivial fix to spelling mistake in dev_dbg message
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Clang warns when multiple pairs of parentheses are used for a single
conditional statement.

drivers/usb/gadget/udc/mv_udc_core.c:188:33: warning: equality
comparison with extraneous parentheses [-Wparentheses-equality]
        while ((curr_dqh->curr_dtd_ptr == curr_dtd->td_dma)) {
                ~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~
drivers/usb/gadget/udc/mv_udc_core.c:188:33: note: remove extraneous
parentheses around the comparison to silence this warning
        while ((curr_dqh->curr_dtd_ptr == curr_dtd->td_dma)) {
               ~                       ^                  ~
drivers/usb/gadget/udc/mv_udc_core.c:188:33: note: use '=' to turn this
equality comparison into an assignment
        while ((curr_dqh->curr_dtd_ptr == curr_dtd->td_dma)) {
                                       ^~
                                       =
1 warning generated.

Link: https://github.com/ClangBuiltLinux/linux/issues/120Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>