The laptop requires a quirk ID to enable its internal microphone. Add
it to the DMI quirk table.
Reported-by: Techno Mooney <techno.mooney@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218402
Cc: stable@vger.kernel.org
Signed-off-by: Techno Mooney <techno.mooney@gmail.com>
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Link: https://msgid.link/r/20240129081148.1044891-1-bagasdotme@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Johan Hovold <johan+linaro@kernel.org>:

To reduce the risk of speaker damage the PA gain needs to be limited on
machines like the Lenovo Thinkpad X13s until we have active speaker
protection in place.

Limit the gain to the current default setting provided by the UCM
configuration which most user have so far been using (due to a bug in
the configuration files which prevented hardware volume control [1]).

The wsa883x PA volume control also turned out to be broken, which meant
that the default setting used by UCM configuration is actually the
lowest level (-3 dB). With the codec driver fixed, hardware volume
control also works as expected.

Note that the new wsa884x driver most likely suffers from a similar bug,
I'll send a fix for that once I've got that confirmed.

Included is also a related fix for the LPASS WSA macro driver, which
was changing the digital gain setting behind the back of user space and
which can result in excessive (or too low) digital gain.

There are further Qualcomm codec drivers that similarly appear to
manipulate various gain settings, but on closer inspection it turns out
that they only write back the current settings. Tests reveal that these
writes are indeed needed for any prior updates to take effect (at least
for the WSA and RX macros).

[1] https://github.com/alsa-project/alsa-ucm-conf/pull/382

Merge series from Zhu Ning <zhuning0077@gmail.com>:

    We get some issues regarding crosstalk, THD+N performance and pop
    noise from customer's project.

The UCM configuration for the Lenovo ThinkPad X13s has up until now
been setting the speaker PA volume to the minimum -3 dB when enabling
the speakers, but this does not prevent the user from increasing the
volume further.

Limit the digital gain and PA volumes to a combined -3 dB in the machine
driver to reduce the risk of speaker damage until we have active speaker
protection in place (or higher safe levels have been established).

Note that the PA volume limit cannot be set lower than 0 dB or
PulseAudio gets confused when the first 16 levels all map to -3 dB.

Also note that this will probably need to be generalised using
machine-specific limits, but a common limit should do for now.

Cc:  <stable@vger.kernel.org>	# 6.5
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://msgid.link/r/20240122181819.4038-3-johan+linaro@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Remove the executable bit that was unintentionally turned on.

Fixes: ee09084f ("ASoC: codecs: ES8326: Add chip version flag")
Signed-off-by: Fei Shao <fshao@chromium.org>
Link: https://msgid.link/r/20240122062055.1673597-1-fshao@chromium.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Sound card on Qualcomm X1E80100 CRD board will use eight DAIs in one DAI
link, so increase the limit.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240117160144.1305127-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Driver does not use any regulator code, so drop redundant include of
regulator/consumer.h header.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240117151208.1219755-3-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Probe calls wcd938x_populate_dt_data() which already prints all the
error cases with dev_err_probe(), so skip the additional dev_err().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240117151208.1219755-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

WCD938x sound codec driver ignores return status of getting regulators
and returns EINVAL instead of EPROBE_DEFER.  If regulator provider
probes after the codec, system is left without probed audio:

  wcd938x_codec audio-codec: wcd938x_probe: Fail to obtain platform data
  wcd938x_codec: probe of audio-codec failed with error -22

Fixes: 16572522 ("ASoC: codecs: wcd938x-sdw: add SoundWire driver")
Cc:  <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240117151208.1219755-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Add condition check for cpu dai link initialization for amplifier
codec path, as same pcm id uses for both headset and speaker path
for RENOIR platforms.
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://msgid.link/r/20240118143023.1903984-3-venkataprasad.potturu@amd.comSigned-off-by: Mark Brown <broonie@kernel.org>

Update platform name for various boards based on rembrandt
and renoir platforms.
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://msgid.link/r/20240118143023.1903984-2-venkataprasad.potturu@amd.comSigned-off-by: Mark Brown <broonie@kernel.org>

Set and enable rt5682s codec bclk and lrclk rates when
acp is in slave mode.
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://msgid.link/r/20240118143023.1903984-1-venkataprasad.potturu@amd.comSigned-off-by: Mark Brown <broonie@kernel.org>

The lowest headphones volume setting does not mute so the leave the TLV
mute flag unset.

This is specifically needed to let the sound server use the lowest gain
setting.

Fixes: c03226ba ("ASoC: codecs: wcd938x: fix dB range for HPHL and HPHR")
Cc:  <stable@vger.kernel.org>      # 6.5
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://msgid.link/r/20240122091130.27463-1-johan+linaro@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The vendor driver appears to be modifying the gain settings behind the
back of user space but these hacks never made it upstream except for
some essentially dead code that adds a constant zero to the current gain
setting on DAPM events.

Note that the volume registers still need to be written after enabling
clocks in order for any prior updates to take effect.
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://msgid.link/r/20240119112420.7446-5-johan+linaro@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The LPASS WSA macro codec driver is updating the digital gain settings
behind the back of user space on DAPM events if companding has been
enabled.

As compander control is exported to user space, this can result in the
digital gain setting being incremented (or decremented) every time the
sound server is started and the codec suspended depending on what the
UCM configuration looks like.

Soon enough playback will become distorted (or too quiet).

This is specifically a problem on the Lenovo ThinkPad X13s as this
bypasses the limit for the digital gain setting that has been set by the
machine driver.

Fix this by simply dropping the compander gain offset hack. If someone
cares about modelling the impact of the compander setting this can
possibly be done by exporting it as a volume control later.

Note that the volume registers still need to be written after enabling
clocks in order for any prior updates to take effect.

Fixes: 2c4066e5 ("ASoC: codecs: lpass-wsa-macro: add dapm widgets and route")
Cc: stable@vger.kernel.org      # 5.11
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://msgid.link/r/20240119112420.7446-4-johan+linaro@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The PA gain can be set in steps of 1.5 dB from -3 dB to 18 dB, that is,
in 15 levels.

Fix the dB values for the PA volume control as experiments using wsa8835
show that the first 16 levels all map to the same lowest gain while the
last three map to the highest gain.

These values specifically need to be correct for the sound server to
provide proper volume control.

Note that level 0 (-3 dB) does not mute the PA so the mute flag should
also not be set.

Fixes: cdb09e62 ("ASoC: codecs: wsa883x: add control, dapm widgets and map")
Cc: stable@vger.kernel.org      # 6.0
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://msgid.link/r/20240119112420.7446-2-johan+linaro@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

We get a noise issue during the startup of recording. We update the
register setting and dapm widgets to fix this issue.
we change callback type of es8326_mute function to mute_stream.
ES8326_ADC_MUTE is moved to es8326_mute function so it can
be turned on at last and turned off at first.
Signed-off-by: Zhu Ning <zhuning0077@gmail.com>
Link: https://msgid.link/r/20240120101240.12496-6-zhuning0077@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

We modify the register settings to minimize headphone pop noise
during ES8326 power-up and music start/stop.
Signed-off-by: Zhu Ning <zhuning0077@gmail.com>
Link: https://msgid.link/r/20240120101240.12496-5-zhuning0077@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

We update the values of some registers in the initialization
sequence in es8326_resume function to improve THD+N performance.
THD+N performance decreases if the output level on headphone is
close to full scale. So we change the register setting in
es8326_jack_detect_handler function to improve THD+N performance
if headphone pulgged. Also, the register setting should be restored
when the headset is unplugged
Signed-off-by: Zhu Ning <zhuning0077@gmail.com>
Link: https://msgid.link/r/20240120101240.12496-3-zhuning0077@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

We change the crosstalk parameter in es8326_resume function
to improve crosstalk performance.
Adding crosstalk kcontrol to enhance the flexibility of crosstalk
debugging in machine.
Adding ES8326_DAC_CROSSTALK macro to declare the crosstalk register.
Signed-off-by: Zhu Ning <zhuning0077@gmail.com>
Link: https://msgid.link/r/20240120101240.12496-2-zhuning0077@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Pull more bcachefs updates from Kent Overstreet:
 "Some fixes, Some refactoring, some minor features:

   - Assorted prep work for disk space accounting rewrite

   - BTREE_TRIGGER_ATOMIC: after combining our trigger callbacks, this
     makes our trigger context more explicit

   - A few fixes to avoid excessive transaction restarts on
     multithreaded workloads: fstests (in addition to ktest tests) are
     now checking slowpath counters, and that's shaking out a few bugs

   - Assorted tracepoint improvements

   - Starting to break up bcachefs_format.h and move on disk types so
     they're with the code they belong to; this will make room to start
     documenting the on disk format better.

   - A few minor fixes"

* tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs: (46 commits)
  bcachefs: Improve inode_to_text()
  bcachefs: logged_ops_format.h
  bcachefs: reflink_format.h
  bcachefs; extents_format.h
  bcachefs: ec_format.h
  bcachefs: subvolume_format.h
  bcachefs: snapshot_format.h
  bcachefs: alloc_background_format.h
  bcachefs: xattr_format.h
  bcachefs: dirent_format.h
  bcachefs: inode_format.h
  bcachefs; quota_format.h
  bcachefs: sb-counters_format.h
  bcachefs: counters.c -> sb-counters.c
  bcachefs: comment bch_subvolume
  bcachefs: bch_snapshot::btime
  bcachefs: add missing __GFP_NOWARN
  bcachefs: opts->compression can now also be applied in the background
  bcachefs: Prep work for variable size btree node buffers
  bcachefs: grab s_umount only if snapshotting
  ...

Pull timer updates from Thomas Gleixner:
 "Updates for time and clocksources:

   - A fix for the idle and iowait time accounting vs CPU hotplug.

     The time is reset on CPU hotplug which makes the accumulated
     systemwide time jump backwards.

   - Assorted fixes and improvements for clocksource/event drivers"

* tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug
  clocksource/drivers/ep93xx: Fix error handling during probe
  clocksource/drivers/cadence-ttc: Fix some kernel-doc warnings
  clocksource/drivers/timer-ti-dm: Fix make W=n kerneldoc warnings
  clocksource/timer-riscv: Add riscv_clock_shutdown callback
  dt-bindings: timer: Add StarFive JH8100 clint
  dt-bindings: timer: thead,c900-aclint-mtimer: separate mtime and mtimecmp regs

Pull powerpc fixes from Aneesh Kumar:

 - Increase default stack size to 32KB for Book3S

Thanks to Michael Ellerman.

* tag 'powerpc-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: Increase default stack size to 32KB

Add line breaks - inode_to_text() is now much easier to read.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs_format.h has gotten too big; let's do some organizing.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Add a field to bch_snapshot for creation time; this will be important
when we start exposing the snapshot tree to userspace.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>