- 13 Dec, 2011 40 commits
-
-
Arend van Spriel authored
The code in aiutils.c now uses the BCMA function for control the registers in the device cores. Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by:
Alwin Beukers <alwin@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
Franky Lin <frankyl@broadcom.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Arend van Spriel authored
The code in pmu.c now uses the functions provided by BCMA to access the core registers. Reviewed-by:
-
Arend van Spriel authored
The code in srom.c now uses the core access function provided by BCMA so no need to pass __iomem pointer any longer. Reviewed-by:
-
Arend van Spriel authored
The code in otp.c now uses the bcma core access functions to read the OTP information from the device. Reviewed-by:
-
Arend van Spriel authored
Instead of returning the core index the function now returns the bcma device for the requested core id. This function is now exposed in the header file. Reviewed-by:
-
Rafał Miłecki authored
Specs were updated. Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Rafał Miłecki authored
The order is different than on older PHYs. Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Eliad Peller authored
The ip address of the vif can be set even before the vif is up. requiring the vif to be up in the vif notifier makes the notifer ignore this event, which causes wrong arp filter configuration later on. Reported-by:
Eyal Shapira <eyal@wizery.com> Signed-off-by:
Eliad Peller <eliad@wizery.com> Signed-off-by:
-
Eliad Peller authored
Configure arp filtering on sta reconfiguration. Signed-off-by:
-
Dmitry TARNYAGIN authored
ieee80211_configure_filter code used local->scanning as a boolean value when it was a bit mask. Bits SCAN_COMPLETED, SCAN_ABORTED should not set FIF_BCN_PRBRESP_PROMISC filter. SCAN_HW_SCANNING should not set FIF_BCN_PRBRESP_PROMISC either, as there is no explicit filter configuration request from scan code. If a driver requires FIF_BCN_PRBRESP_PROMISC mode during HW scanning, it's up to the driver to temporary enable it. Similar mistake was fixed also in ieee80211_hw_config (power configuration code). Verified-by:
Vitaly Wool <vitaly.wool@sonyericsson.com> Signed-off-by:
Dmitry Tarnyagin <dmitry.tarnyagin@stericsson.com> Signed-off-by:
-
Stanislaw Gruszka authored
With previous patch "rtlwifi: use work for lps" we can now use mutex for protecting ps mode changing critical sections. This fixes running system with interrupts disabled for long time. Merge ips_lock and lps_lock as they seems to protect the same data structures (accessed in rtl_ps_set_rf_state() function). Reported-by:
Philipp Dreimann <philipp@dreimann.net> Tested-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Mike McCormack <mikem@ring3k.org> Cc: Chaoming Li <chaoming_li@realsil.com.cn> Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
Tim Gardner <tim.gardner@canonical.com> Signed-off-by:
-
Stanislaw Gruszka authored
Leaving leisure power save mode can take some time, so it's better to perform that action in process context with interrupts enabled. This patch changes lps_leave tasklet to work. Reported-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Rafał Miłecki authored
Changes were obtained from MMIO dump from 5.100.82.112. Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
-
Rafał Miłecki authored
bcma used to lock up machine without enabling PCI or initializing CC. Cc: stable@vger.kernel.org Signed-off-by:
-
Avinash Patil authored
replace single queue function calls with equivalent multiple queue functions. Wakeup queue and stop queue calls are guarded by spin lock. Signed-off-by:
Avinash Patil <patila@marvell.com> Signed-off-by:
Kiran Divekar <dkiran@marvell.com> Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
-
Avinash Patil authored
Free SKBs allocated during multiport aggrgation setup when RX multiport aggregation fails in the middle. With this handling freeing SKB in mwifiex_process_int_status() for failure case is removed. Also handles single RX transaction failure. Signed-off-by:
-
Amitkumar Karwar authored
Event buffers for PCIe interface are allocated during driver initialisation, and respective physical addresses are sent to FW in *_PCIE_DESC_DETAILS command so that FW can do DMA. These buffers will be freed while unloading the driver. Therefore we should not free them in event handling error path. Also we should skip next pending events in failure case. Also fixed 'returning -1 instead of -ENOMEM is sloppy' warnings. Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
-
Arend van Spriel authored
Code in nicpci.c now uses the PCI(E) core as provided by the BCMA bus driver to configure that core. Reviewed-by:
-
Arend van Spriel authored
BCMA provides functions to control the state of the cores so using that and remove similar implementation from the driver. Reviewed-by:
-
Arend van Spriel authored
Several functions provided by aiutils.c are not used in brcmsmac driver and have been removed. Reviewed-by:
-
Arend van Spriel authored
The ai_corereg() function is only used in the driver to safely access the chipcommon core. The function has been renamed to ai_cc_reg() removing the need to provide a core index parameter. Reviewed-by:
-
Arend van Spriel authored
The use of SI_FAST() macro interferes with the BCMA integration as it causes BCMA and aiutils.c to get out of sync on what the current core is. When everything is using BCMA we will try to add SI_FAST functionality to BCMA to avoid unnecessary core switching. Reviewed-by:
-
Arend van Spriel authored
This adds the use of bcma functions to access the registers within the phy source code. Reviewed-by:
-
Arend van Spriel authored
The dma.c source file now uses the register access functions provided by bcma. Reviewed-by:
-
Arend van Spriel authored
Using BCMA hides the specifics about the host interface. The driver is now using the DMA-API to do dma related calls. BCMA provides the device object to use in the DMA-API calls. Reviewed-by:
-
Arend van Spriel authored
The driver now uses the bcma register access functions to read and write the registers on the 802.11 core. The dma and phy code need to be modified next and access to the other cores. That will be done in coming patches. Reviewed-by:
-
Arend van Spriel authored
The core enumeration rom is already parsed by the bcma bus driver and there is no need to repeat the exercise. The ai_scan() function still exists but is targetted for removal as well. Reviewed-by:
-
Arend van Spriel authored
The ai_attach now takes a bcma_bus object as its parameter to obtain all required information needed for chip control. Reviewed-by:
-
Arend van Spriel authored
When moving to bcma usage there are two busses in play. The pci bus connecting the device to the host and the bcma bus connecting the cores in the device. To distinguish this the attribute pbus has been renamed to a more explicit name, ie. pcibus. Reviewed-by:
-
Arend van Spriel authored
The driver is probed through bcma which provides a device representing the core. This device is now passed in brcms_c_attach and brcms_b_attach functions. Reviewed-by:
-
Arend van Spriel authored
A new bus driver called "bcma" has been introduced into the kernel tree which considers the Broadcom AMBA chip interconnect as a bus. Each core in the chip is a bcma device. This commit changes brcms_mac80211.c into a bcma device driver. Reviewed-by:
-
