Allocate msis such that each time a new interrupt is requested,
the SRS (MSIR register select) to be used is allocated in a
round-robin fashion.
The end result is that the msi interrupts will be spread across
distinct MSIRs with the main benefit that now users can set
affinity to each msi int through the mpic irq backing up the
MSIR register.
This is achieved with the help of a newly introduced msi bitmap
api that allows specifying the starting point when searching
for a free msi interrupt.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

Rename the irq controller associated with a MSI
interrupt to fsl-msi-<V>, where <V> is the virq
of the cascade irq backing up this MSI interrupt.
This way, one can set the affinity of a MSI
through the cascade irq associated with said MSI
interrupt.
Given this example /proc/interrupts snippet:

           CPU0       CPU1       CPU2       CPU3
 16:          0          0          0          0   OpenPIC    16 Edge      mpic-error-int
 17:          0          4          0          0  fsl-msi-224   0 Edge      eth0-rx-0
 18:          0          5          0          0  fsl-msi-225   1 Edge      eth0-tx-0
 19:          0          2          0          0  fsl-msi-226   2 Edge      eth0
 [...]
224:          0         11          0          0   OpenPIC   224 Edge      fsl-msi-cascade
225:          0          0          0          0   OpenPIC   225 Edge      fsl-msi-cascade
226:          0          0          0          0   OpenPIC   226 Edge      fsl-msi-cascade
 [...]

To change the affinity of MSI interrupt 17
(having the irq controller named "fsl-msi-224")
instead of writing /proc/irq/17/smp_affinity, use
the associated MSI cascade irq, in this case,
interrupt 224, e.g.:

   echo 6 > /proc/irq/224/smp_affinity

Note that a MSI cascade irq covers several MSI
interrupts, so changing the affinity on the
cascade will impact all of the associated MSI
interrupts.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

As we do for other fsl-mpic related cascaded irqchips
(e.g. error ints, mpic timers), use a normal irq handler
for msi irqs too.
This brings some advantages such as mask/unmask/ack/eoi
and irq state taken care behind the scenes, kstats
updates a.s.o plus access to features provided by mpic,
such as affinity.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

Store cascade_data in an array inside the driver
data for later use.
Get rid of the msi_virq array since now we can
encapsulate the virqs in the cascade_data
directly and access them through the array
mentioned earlier.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

Change USB controller version to 2.5 in compatible string for T4240
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

The following commit prevents the MPC8548E on the XPedite5200 PrPMC
module from enumerating its PCI/PCI-X bus:

    powerpc/fsl-pci: use 'Header Type' to identify PCIE mode

The previous patch prevents any Freescale PCI-X bridge from enumerating
the bus, if it is hardware strapped into Agent mode.

In PCI-X, the Host is responsible for driving the PCI-X initialization
pattern to devices on the bus, so that they know whether to operate in
conventional PCI or PCI-X mode as well as what the bus timing will be.
For a PCI-X PrPMC, the pattern is driven by the mezzanine carrier it is
installed onto. Therefore, PrPMCs are PCI-X Agents, but one per system
may still enumerate the bus.

This patch causes the device node of any PCI/PCI-X bridge strapped into
Agent mode to be checked for the fsl,pci-agent-force-enum property. If
the property is present in the node, the bridge will be allowed to
enumerate the bus.

Cc: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

Add CONFIG_NLS_CODEPAGE_437, CONFIG_NLS_CODEPAGE_850,
CONFIG_NLS_ISO8859_1 in default configs for 85xx
and 86xx socs. Required for mounting vfat file-systems
on USB devices
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

According to Freescale manuals, the IFC_CSORn_EXT register is located
immediately _after_ the bank's IFC_CSORn register.

This patch adjusts the csor_ext member of and reserved register arrays
immediately surrounding the csor_cs structure to provide proper access
to this register.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Acked-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

The new MSI block in MPIC 4.3 added the MSIIR1 register,
with a different layout, in order to support 16 MSIR
registers. The msi binding was also updated so that
the "reg" reflects the newly introduced MSIIR1 register.
Virtual machines advertise these msi nodes by using the
compatible "fsl,vmpic-msi-v4.3" so add support for it.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

FSL PCI cannot directly address the whole lower 4 GiB due to
conflicts with PCICSRBAR and outbound windows.  By the time
max_direct_dma_addr is set to the precise limit, it will be too late to
alter the zone limits, but we should always have at least 2 GiB mapped
(unless RAM is smaller than that).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>

A DMA zone is still needed with swiotlb, for coherent allocations.
This doesn't affect platforms that don't use swiotlb or that don't call
swiotlb_detect_4g().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>

FSL PCI cannot directly address the whole lower 4 GiB due to
conflicts with PCICSRBAR and outbound windows, and thus
max_direct_dma_addr is less than 4GiB.  Honor that limit in
dma_direct_alloc_coherent().

Note that setting the DMA mask to 31 bits is not an option, since many
PCI drivers would fail if we reject 32-bit DMA in dma_supported(), and
we have no control over the setting of coherent_dma_mask if
dma_supported() returns true.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>

Platform code can call limit_zone_pfn() to set appropriate limits
for ZONE_DMA and ZONE_DMA32, and dma_direct_alloc_coherent() will
select a suitable zone based on a device's mask and the pfn limits that
platform code has configured.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>

T2080PCIe-RDB is a Freescale Reference Design Board that hosts T2080 SoC.
The board feature overview:
Processor:
 - T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
DDR Memory:
 - Single memory controller capable of supporting DDR3 and DDR3-LP devices
 - 72bit 4GB DDR3-LP SODIMM in slot
Ethernet interfaces:
 - Two 1Gbps RGMII ports on-board
 - Two 10Gbps SFP+ ports on-board
 - Two 10Gbps Base-T ports on-board
Accelerator:
 - DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
IFC/Local Bus
 - NOR:  128MB 16-bit NOR flash
 - NAND: 1GB 8-bit NAND flash
 - CPLD: for system controlling with programable header on-board
eSPI:
 - 64MB N25Q512 SPI flash
USB:
 - Two USB2.0 ports with internal PHY (both Type-A)
PCIe:
 - One PCIe x4 goldfinger(support SR-IOV)
 - One PCIe x4 slot
 - One PCIe x2 end-point device (C293 crypto co-processor)
SATA:
 - Two SATA 2.0 ports on-board
SDHC:
 - support a MicroSD/TF card on-board
I2C:
 - Four I2C controllers.
UART:
 - Dual 4-pins UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

Some Freescale boards like T1040RDB have an on board CPLD connected on
the IFC bus. Add binding for cpld in board.txt file
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

In commit ae91d60b, a bug was fixed that
involved converting !x & y to !(x & y).  The code below shows the same
pattern, and thus should perhaps be fixed in the same way.

This is not tested and clearly changes the semantics, so it is only
something to consider.

The Coccinelle semantic patch that makes this change is as follows:

// <smpl>
@@ expression E1,E2; @@
(
  !E1 & !E2
|
- !E1 & E2
+ !(E1 & E2)
)
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

mpic_msgrs has type struct mpic_msgr **, not struct mpic_msgr *, so the
elements of the array should have pointer type, not structure type.
The advantage of kcalloc is, that will prevent integer overflows which
could result from the multiplication of number of elements and size and
it is also a bit nicer to read.

The Coccinelle semantic patch that makes the first change is as follows:

// <smpl>
@disable sizeof_type_expr@
type T;
T **x;
@@

  x =
  <+...sizeof(
- T
+ *x
  )...+>
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>

The CoreNet Coherency Fabric is part of the memory subsystem on
some Freescale QorIQ chips.  It can report coherency violations (e.g.
due to misusing memory that is mapped noncoherent) as well as
transactions that do not hit any local access window, or which hit a
local access window with an invalid target ID.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Bharat Bhushan <bharat.bhushan@freescale.com>

Erratum A-008139 can cause duplicate TLB entries if an indirect
entry is overwritten using tlbwe while the other thread is using it to
do a lookup.  Work around this by using tlbilx to invalidate prior
to overwriting.

To avoid the need to save another register to hold MAS1 during the
workaround code, TID clearing has been moved from tlb_miss_kernel_e6500
until after the SMT section.
Signed-off-by: Scott Wood <scottwood@freescale.com>

The general idea is that each core will release all of its
threads into the secondary thread startup code, which will
eventually wait in the secondary core holding area, for the
appropriate bit in the PACA to be set. The kick_cpu function
pointer will set that bit in the PACA, and thus "release"
the core/thread to boot. We also need to do a few things that
U-Boot normally does for CPUs (like enable branch prediction).
Signed-off-by: Andy Fleming <afleming@freescale.com>
[scottwood@freescale.com: various changes, including only enabling
 threads if Linux wants to kick them]
Signed-off-by: Scott Wood <scottwood@freescale.com>

This ensures that all MSR definitions are consistently unsigned long,
and that MSR_CM does not become 0xffffffff80000000 (this is usually
harmless because MSR is 32-bit on booke and is mainly noticeable when
debugging, but still I'd rather avoid it).
Signed-off-by: Scott Wood <scottwood@freescale.com>

They're almost a duplicate of the boards array
and we can build them at run-time.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

Add support for Freescale T2080/T2081 QDS Development System Board.

The T2080QDS Development System is a high-performance computing,
evaluation, and development platform that supports T2080 QorIQ
Power Architecture processor, with following major features:

T2080QDS feature overview:
Processor:
 - T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
Memory:
 - Single memory controller capable of supporting DDR3 and DDR3-LP
 - Dual DIMM slots up 2133MT/s with ECC
Ethernet interfaces:
 - Two 1Gbps RGMII on-board ports
 - Four 10Gbps XFI on-board cages
 - 1Gbps/2.5Gbps SGMII Riser card
 - 10Gbps XAUI Riser card
Accelerator:
 - DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes:
 - 16 lanes up to 10.3125GHz
 - Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, XFI and XAUI
IFC:
 - 128MB NOR Flash, 512MB NAND Flash, PromJet debug port and FPGA
eSPI:
 - Three SPI flash (16MB N25Q128A + 8MB EN25S64 + 512KB SST25WF040)
USB:
 - Two USB2.0 ports with internal PHY (one Type-A + one micro Type-AB)
PCIE:
 - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0, SR-IOV)
SATA:
 - Two SATA 2.0 ports on-board
SRIO:
 - Two Serial RapidIO 2.0 ports up to 5 GHz
eSDHC:
 - Supports SD/MMC/eMMC Card
DMA:
 - Three 8-channels DMA controllers
I2C:
 - Four I2C controllers.
UART:
 - Dual 4-pins UART serial ports
System Logic:
 - QIXIS-II FPGA system controll

T2081QDS board shares the same PCB with T1040QDS with some differences.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

The T2080 QorIQ multicore processor combines four dual-threaded e6500 Power
Architecture processor cores with high-performance datapath acceleration
logic and network and peripheral bus interfaces required for networking,
telecom/datacom, wireless infrastructure, and mil/aerospace applications.

The T2080 SoC includes the following function and features:
- Four dual-threaded 64-bit Power architecture e6500 cores, up to 1.8GHz
- 2MB L2 cache and 512KB CoreNet platform cache (CPC)
- Hierarchical interconnect fabric
- One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- 16 SerDes lanes up to 10.3125 GHz
- 8 Ethernet interfaces (multiple 1G/2.5G/10G MACs)
- High-speed peripheral interfaces
  - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0)
  - Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz
- Additional peripheral interfaces
  - Two serial ATA (SATA 2.0) controllers
  - Two high-speed USB 2.0 controllers with integrated PHY
  - Enhanced secure digital host controller (SD/SDXC/eMMC)
  - Enhanced serial peripheral interface (eSPI)
  - Four I2C controllers
  - Four 2-pin UARTs or two 4-pin UARTs
  - Integrated Flash Controller supporting NAND and NOR flash
- Three eight-channel DMA engines
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0

T2081 is a reduced personality of T2080 with following difference:
Feature               T2080 T2081
1G Ethernet numbers:  8     6
10G Ethernet numbers: 4     2
SerDes lanes:         16    8
Serial RapidIO,RMan:  2     no
SATA Controller:      2     no
Aurora:               yes   no
SoC Package:          896-pins 780-pins
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[scottwood@freescale.com: added fsl,qoriq-pci-v3.0 for U-Boot compat]
Signed-off-by: Scott Wood <scottwood@freescale.com>

m8xx_pcmcia_ops was the only thing in this file (other than a comment
that describes a usage that doesn't match the file's contents); now
that m8xx_pcmcia_ops is gone, remove the empty file.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Pantelis Antoniou <pantelis.antoniou@gmail.com>
Cc: Vitaly Bordug <vitb@kernel.crashing.org>
Cc: netdev@vger.kernel.org

This driver doesn't build, and apparently has not built since
arch/ppc was removed in 2008 (when mk_int_int_mask was removed
from asm/irq.h, among other build errors).

A few weeks ago I asked whether anyone was actively maintaining
this code, and got no positive response:
http://patchwork.ozlabs.org/patch/352082/

So, let's remove it.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Vitaly Bordug <vitb@kernel.crashing.org>
Cc: linux-pcmcia@lists.infradead.org
Cc: Paul Bolle <pebolle@tiscali.nl>

This fixes below compilation error on SOCs where CONFIG_PHYS_64BIT
is not defined:

 arch/powerpc/kvm/e500_mmu_host.c: In function 'kvmppc_e500_shadow_map':
| arch/powerpc/kvm/e500_mmu_host.c:631:20: error: 'PTE_WIMGE_SHIFT' undeclared (first use in this function)
|    wimg = (*ptep >> PTE_WIMGE_SHIFT) & MAS2_WIMGE_MASK;
|                     ^
| arch/powerpc/kvm/e500_mmu_host.c:631:20: note: each undeclared identifier is reported only once for each function it appears in
| make[1]: *** [arch/powerpc/kvm/e500_mmu_host.o] Error 1
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

In machine_check_e500 exception handler is a wrong indication
in case of MCSR_BUS_WBERR - so print "Write" instead of "Read".
Signed-off-by: Wladislav Wiebe <wladislav.kw@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

T4240RDB board Specification
----------------------------
Memory subsystem:
     6GB DDR3
     128MB NOR flash
     2GB NAND flash
Ethernet:
     Eight 1G SGMII ports
     Four 10Gbps SFP+ ports
PCIe:
     Two PCIe slots
USB:
     Two USB2.0 Type A ports
SDHC:
     One SD-card port
SATA:
     One SATA port
UART:
     Dual RJ45 ports
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

The mux2 node is missing the clock-output-names field that is required
by the clk-ppc-corenet driver.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

About a year ago I began taking patches, technically as Kumar's
assistant -- but since then all of the pull requests for this area have
come from me, and I've been doing most of the reviews.  Update
MAINTAINERS to reflect this.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Virtualized environments may expose a e6500 dual-threaded core
as two single-threaded e6500 cores. Take advantage of this
and get rid of the tlb lock and the trap-causing tlbsx in
the htw miss handler by guarding with CPU_FTR_SMT, as it's
already being done in the bolted tlb1 miss handler.

As seen in the results below, measurements done with lmbench
random memory access latency test running under Freescale's
Embedded Hypervisor, there is a ~34% improvement.

Memory latencies in nanoseconds - smaller is better
    (WARNING - may not be correct, check graphs)
----------------------------------------------------
Host       Mhz   L1 $   L2 $    Main mem    Rand mem
---------  ---   ----   ----    --------    --------
smt       1665 1.8020   13.2    83.0         1149.7
nosmt     1665 1.8020   13.2    83.0          758.1
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
[scottwood@freescale.com: commit message tweak]
Signed-off-by: Scott Wood <scottwood@freescale.com>

Not involved in 8xx activities for years, update MAINTAINERS
to reflect it.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

T4240 has a third DMA engine controller, so add the corresponding DMA
node into the dts file.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
[scottwood@freescale.com: reword commit message]
Signed-off-by: Scott Wood <scottwood@freescale.com>

- remove CONFIG_RTC_DRV_CMOS in corenet32_smp_defconfig(it's unused),
  reserve CONFIG_RTC_DRV_CMOS in mpc85xx_defconfig(needed on some CDS boards)

- enable CONFIG_RTC_DRV_DS1307, CONFIG_RTC_DRV_DS1374,
  CONFIG_RTC_DRV_DS3232 in mpc85xx_defconfig, mpc85xx_smp_defconfig

- enable RTC support in  corenet64_smp_defconfig
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

Signed-off-by: Scott Wood <scottwood@freescale.com>
Reported-by: Ed Swarthout <ed.swarthout@freescale.com>

Commit 82d86de2 "TLB lock recursive"
introduced a bug whereby cpu 0 uses the same value for "lock held" as
is used to indicate that the lock is free.  This means that cpu 1 can
acquire the lock whenever it wants, regardless of whether cpu 0 has it
locked, which in turn means we can get duplicate TLB entries.

Add one to the CPU value to ensure we do not use zero as a "lock held"
value.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reported-by: Ed Swarthout <ed.swarthout@freescale.com>

Previously TID was being cleared before the tlbsx, but not after.  This
can lead to a multiway hit between a TLB entry with TID=0 (previously
inserted when PID=0) and a TLB entry with TID!=0 that matches PID.
This can theoretically result in undefined behavior, though we probably
get lucky due to the details of the overlap.  It also results in the
inability to use multihit detection to detect other conflicting TLB
entries, as well as poorer TLB utilization due to duplicating kernel
TLB entries.

Rather than try to patch up MAS1 after tlbsx, the entire value is
saved/restored as with MAS2.

I observed a slight improvement in TLB miss performance with this patch
applied.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reported-by: Ed Swarthout <ed.swarthout@freescale.com>

This reverts commit e1edf18b.

This patch was a misguided attempt at fixing offb for LE ppc64
kernels on BE qemu but is just wrong ... it breaks real LE/LE
setups, LE with real HW, and existing mixed endian systems
that did the fight thing with the appropriate device-tree
property. Bad reviewing on my part, sorry.

The right fix is to either make qemu change its endian when
the guest changes endian (working on that) or to use the
existing foreign endian support.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.13+]
---