- 06 Jul, 2022 2 commits
-
-
Bo-Chen Chen authored
MediaTek dpi supports direct connection to dpi panels while dp_intf does not support. Therefore, add a config "support_direct_pin" to control this. Signed-off-by:
Bo-Chen Chen <rex-bc.chen@mediatek.com> Reviewed-by:
AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220705102530.1344-3-rex-bc.chen@mediatek.com/Signed-off-by:
Chun-Kuang Hu <chunkuang.hu@kernel.org>
-
Bo-Chen Chen authored
Dp_intf supports YUV422 as output format. In MT8195 Chrome project, YUV422 output format is used for 4K resolution. To support this, it is also needed to support color format transfer. Color format transfer is a new feature for both dpi and dpintf of MT8195. The input format could be RGB888 and output format for dp_intf should be YUV422. Therefore, we add a mtk_dpi_matrix_sel() helper to update the DPI_MATRIX_SET register depending on the color format. Signed-off-by:
Guillaume Ranquet <granquet@baylibre.com> Signed-off-by:
-
- 04 Jul, 2022 14 commits
-
-
Guillaume Ranquet authored
Add flexibility by moving the csc_enable bit to SoC specific config Signed-off-by:
-
Guillaume Ranquet authored
Add flexibility by moving the yuv422 en bit to SoC specific config Signed-off-by:
-
Guillaume Ranquet authored
Add flexibility by moving the swap shift value to SoC specific config. Signed-off-by:
-
Guillaume Ranquet authored
Add flexibility by moving the hvsize mask to SoC specific config. Signed-off-by:
-
Guillaume Ranquet authored
Add flexibility by moving the dimension mask to the SoC config Signed-off-by:
-
Guillaume Ranquet authored
The hardware design of dp_intf does not support input swap, so we add a bit of flexibility to support SoCs without swap_input support. We also add a warning message if the hardware is not supported and it needs to swap input. Signed-off-by:
-
Guillaume Ranquet authored
Dp_intf does not support CK/DE polarity because the polarity information is not used for eDP and DP while dp_intf is only for eDP and DP. Therefore, we add a bit of flexibility to support SoCs without CK/DE pol support. Signed-off-by:
-
Bo-Chen Chen authored
For RGB colorimetry, CTA-861 support both limited and full range data when receiving video with RGB color space. We use drm_default_rgb_quant_range() to determine the correct setting. Signed-off-by:
-
Guillaume Ranquet authored
Enabling the dpi too early causes glitches on screen. Move the call to mtk_dpi_enable() at the end of the bridge_enable callback to ensure everything is setup properly before enabling dpi. Fixes: 9e629c17 ("drm/mediatek: Add DPI sub driver") Signed-off-by:
-
Bo-Chen Chen authored
DPI is not support output format as YUV, but there is the setting of configuring output YUV. Therefore, remove them in this patch. Fixes: 9e629c17 ("drm/mediatek: Add DPI sub driver") Signed-off-by:
-
Bo-Chen Chen authored
This driver will support dp_intf and there are many configs between dpi and dp_intf. Therefore, we will add many configs in "struct mtk_dpi_conf". To let this structure more readable, we add this kernel doc. Signed-off-by:
-
Bo-Chen Chen authored
Strings replacement: - s/mediatek/MediaTek/ in title. - s/Mediatek/MediaTek/ in description. Signed-off-by:
Rob Herring <robh@kernel.org> Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220701035845.16458-3-rex-bc.chen@mediatek.com/Signed-off-by:
-
Markus Schneider-Pargmann authored
DP_INTF is similar to DPI but does not have the exact same feature set or register layouts. DP_INTF is the sink of the display pipeline that is connected to the DisplayPort controller and encoder unit. It takes the same clocks as DPI. Signed-off-by:
Markus Schneider-Pargmann <msp@baylibre.com> Signed-off-by:
-
Hsin-Yi Wang authored
Make sure bridge_disable will be called before suspend by calling drm_mode_config_helper_suspend() in .prepare callback. Signed-off-by:
Hsin-Yi Wang <hsinyi@chromium.org> Reviewed-by:
-
- 03 Jul, 2022 1 commit
-
-
Allen-KH Cheng authored
The compatible “mediatek,mt8192-disp-rdma” is being used for reading the data into DMA for back-end panel driver in mt8192 but there is no difference between mt8183 and mt8192 in rdma driver. Remove compatible “mediatek,mt8192-disp-rdma” from the driver and should use “mediatek,mt8183-disp-rdma” as fallback in 8192 DTS according to the mediatek,rdma.yaml. Signed-off-by:
Allen-KH Cheng <allen-kh.cheng@mediatek.com> Reviewed-by:
Chen-Yu Tsai <wenst@chromium.org> Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220701090547.21429-2-allen-kh.cheng@mediatek.com/Signed-off-by:
-
- 27 Jun, 2022 7 commits
-
-
Nancy.Lin authored
Add plane color encoding information for color space conversion. It's a preparation for adding support for mt8195 ovl_adaptor mdp_rdma csc control. Signed-off-by:
Nancy.Lin <nancy.lin@mediatek.com> Reviewed-by:
-
Nancy.Lin authored
Add merge async reset control in mtk_merge_stop. Async hw doesn't do self reset on each sof signal(start of frame), so need to reset the async to clear the hw status for the next merge start. Signed-off-by:
-
Nancy.Lin authored
Add merge mute/unmute setting for MT8195. MT8195 Vdosys1 merge1~merge4 support HW mute function. Signed-off-by:
-
Nancy.Lin authored
Add merge start/stop API for cmdq support. The ovl_adaptor merges are configured with each drm plane update. Need to enable/disable merge with cmdq making sure all the settings taken effect in the same vblank. Signed-off-by:
-
Nancy.Lin authored
Add merge new advance config API. The original merge API is mtk_ddp_comp_funcs function prototype. The API interface parameters cannot be modified, so add a new config API for extension. This is the preparation for ovl_adaptor merge control. Signed-off-by:
-
Nancy.Lin authored
Add MDP_RDMA driver for MT8195. MDP_RDMA is the DMA engine of the ovl_adaptor component. Signed-off-by:
-
Nancy.Lin authored
Add vdosys1 RDMA definition. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Tested-by:
-
- 09 Jun, 2022 4 commits
-
-
Rex-BC Chen authored
The compatible "mediatek,mt8186-dsi" is used by MT8186 DSI, so add it to mtk_ddp_comp_dt_ids in mtk_drm_drv.c. Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220504091923.2219-5-rex-bc.chen@mediatek.com/Signed-off-by:
-
Xinlei Lee authored
Add the compatible because use different cmdq addresses in mt8186. Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220504091923.2219-4-rex-bc.chen@mediatek.com/Signed-off-by:
Xinlei Lee <xinlei.lee@mediatek.com> Reviewed-by:
-
Xinlei Lee authored
Add dt-binding documentation of dsi for MediaTek MT8186 SoC. Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220504091923.2219-3-rex-bc.chen@mediatek.com/Signed-off-by:
-
Xinlei Lee authored
Convert mediatek,dsi.txt to mediatek,dsi.yaml format Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220504091923.2219-2-rex-bc.chen@mediatek.com/Signed-off-by:
-
- 06 Jun, 2022 11 commits
-
-
Xinlei Lee authored
In the dsi_enable function, mtk_dsi_rxtx_control is to pull up the MIPI signal operation. Before dsi_disable, MIPI should also be pulled down by writing a register instead of disabling dsi. If disable dsi without pulling the mipi signal low, the value of the register will still maintain the setting of the mipi signal being pulled high. After resume, even if the mipi signal is not pulled high, it will still be in the high state. Fixes: 2e54c14e ("drm/mediatek: Add DSI sub driver") Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1653012007-11854-5-git-send-email-xinlei.lee@mediatek.com/Signed-off-by:
Jitao Shi <jitao.shi@mediatek.com> Signed-off-by:
-
Jitao Shi authored
To comply with the panel sequence, hold the mipi signal to LP00 before the dcs cmds transmission, and pull the mipi signal high from LP00 to LP11 until the start of the dcs cmds transmission. The normal panel timing is : (1) pp1800 DC pull up (2) avdd & avee AC pull high (3) lcm_reset pull high -> pull low -> pull high (4) Pull MIPI signal high (LP11) -> initial code -> send video data (HS mode) The power-off sequence is reversed. If dsi is not in cmd mode, then dsi will pull the mipi signal high in the mtk_output_dsi_enable function. The delay in lane_ready func is the reaction time of dsi_rx after pulling up the mipi signal. Fixes: 2dd8075d ("drm/mediatek: mtk_dsi: Use the drm_panel_bridge API") Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1653012007-11854-4-git-send-email-xinlei.lee@mediatek.com/ Cc: <stable@vger.kernel.org> # 5.10.x: 7f6335c6: drm/mediatek: Modify dsi funcs to atomic operations Cc: <stable@vger.kernel.org> # 5.10.x: cde7e2e3: drm/mediatek: Separate poweron/poweroff from enable/disable and define new funcs Cc: <stable@vger.kernel.org> # 5.10.x Signed-off-by: -
Jitao Shi authored
In order to match the changes of "Use the drm_panel_bridge API", the poweron/poweroff of dsi is extracted from enable/disable and defined as new funcs (atomic_pre_enable/atomic_post_disable). Since dsi_poweron is moved from dsi_enable to pre_enable function, in order to avoid poweron failure, the operation of dsi register fails to cause bus hang. Therefore, the protection mechanism is added to the dsi_enable function. Fixes: 2dd8075d ("drm/mediatek: mtk_dsi: Use the drm_panel_bridge API") Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1653012007-11854-3-git-send-email-xinlei.lee@mediatek.com/Signed-off-by:
-
Xinlei Lee authored
Because .enable & .disable are deprecated. Use .atomic_enable & .atomic_disable instead. Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1653012007-11854-2-git-send-email-xinlei.lee@mediatek.com/Signed-off-by:
-
jason-jh.lin authored
Because mt8195 vdosys0 has 2 DITHER components, so the suffix 0 need to be added to DDP_COMPONENT_DITHER. Then DITHER enum will become: DDP_COMPONENT_DITHER0 and DDP_COMPONENT_DITHER1. Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220526102126.19756-5-jason-jh.lin@mediatek.com/Signed-off-by:
jason-jh.lin <jason-jh.lin@mediatek.com> Reviewed-by:
-
jason-jh.lin authored
1. Add driver data of mt8195 vdosys0 to mediatek-drm and the sub driver. 2. Add get driver data function to identify which vdosys by io_start. Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220526102126.19756-4-jason-jh.lin@mediatek.com/Signed-off-by:
-
jason-jh.lin authored
Add MERGE engine file: MERGE module is used to merge two slice-per-line inputs into one side-by-side output. Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220526102126.19756-3-jason-jh.lin@mediatek.com/Signed-off-by:
-
jason-jh.lin authored
DSC is designed for real-time systems with real-time compression, transmission, decompression and display. The DSC standard is a specification of the algorithms used for compressing and decompressing image display streams, including the specification of the syntax and semantics of the compressed video bit stream. Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220526102126.19756-2-jason-jh.lin@mediatek.com/Signed-off-by:
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull file descriptor fix from Al Viro: "Fix for breakage in #work.fd this window" * tag 'pull-work.fd-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: fix the breakage in close_fd_get_file() calling conventions change
-
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mmLinus Torvalds authored
Pull mm hotfixes from Andrew Morton: "Fixups for various recently-added and longer-term issues and a few minor tweaks: - fixes for material merged during this merge window - cc:stable fixes for more longstanding issues - minor mailmap and MAINTAINERS updates" * tag 'mm-hotfixes-stable-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: mm/oom_kill.c: fix vm_oom_kill_table[] ifdeffery x86/kexec: fix memory leak of elf header buffer mm/memremap: fix missing call to untrack_pfn() in pagemap_range() mm: page_isolation: use compound_nr() correctly in isolate_single_pageblock() mm: hugetlb_vmemmap: fix CONFIG_HUGETLB_PAGE_FREE_VMEMMAP_DEFAULT_ON MAINTAINERS: add maintainer information for z3fold mailmap: update Josh Poimboeuf's email
-
- 05 Jun, 2022 1 commit
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mmLinus Torvalds authored
Pull delay-accounting update from Andrew Morton: "A single featurette for delay accounting. Delayed a bit because, unusually, it had dependencies on both the mm-stable and mm-nonmm-stable queues" * tag 'mm-nonmm-stable-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: delayacct: track delays from write-protect copy
-
