- 26 Jan, 2019 40 commits
-
-
Maciej W. Rozycki authored
[ Upstream commit e4849aff ] The Broadcom SiByte BCM1250, BCM1125, and BCM1125H SOCs have an onchip DRAM controller that supports memory amounts of up to 16GiB, and due to how the address decoder has been wired in the SOC any memory beyond 1GiB is actually mapped starting from 4GiB physical up, that is beyond the 32-bit addressable limit[1]. Consequently if the maximum amount of memory has been installed, then it will span up to 19GiB. Many of the evaluation boards we support that are based on one of these SOCs have their memory soldered and the amount present fits in the 32-bit address range. The BCM91250A SWARM board however has actual DIMM slots and accepts, depending on the peripherals revision of the SOC, up to 4GiB or 8GiB of memory in commercially available JEDEC modules[2]. I believe this is also the case with the BCM91250C2 LittleSur board. This means that up to either 3GiB or 7GiB of memory requires 64-bit addressing to access. I believe the BCM91480B BigSur board, which has the BCM1480 SOC instead, accepts at least as much memory, although I have no documentation or actual hardware available to verify that. Both systems have PCI slots installed for use by any PCI option boards, including ones that only support 32-bit addressing (additionally the 32-bit PCI host bridge of the BCM1250, BCM1125, and BCM1125H SOCs limits addressing to 32-bits), and there is no IOMMU available. Therefore for PCI DMA to work in the presence of memory beyond enable swiotlb for the affected systems. All the other SOC onchip DMA devices use 40-bit addressing and therefore can address the whole memory, so only enable swiotlb if PCI support and support for DMA beyond 4GiB have been both enabled in the configuration of the kernel. This shows up as follows: Broadcom SiByte BCM1250 B2 @ 800 MHz (SB1 rev 2) Board type: SiByte BCM91250A (SWARM) Determined physical RAM map: memory: 000000000fe7fe00 @ 0000000000000000 (usable) memory: 000000001ffffe00 @ 0000000080000000 (usable) memory: 000000000ffffe00 @ 00000000c0000000 (usable) memory: 0000000087fffe00 @ 0000000100000000 (usable) software IO TLB: mapped [mem 0xcbffc000-0xcfffc000] (64MB) in the bootstrap log and removes failures like these: defxx 0000:02:00.0: dma_direct_map_page: overflow 0x0000000185bc6080+4608 of device mask ffffffff bus mask 0 fddi0: Receive buffer allocation failed fddi0: Adapter open failed! IP-Config: Failed to open fddi0 defxx 0000:09:08.0: dma_direct_map_page: overflow 0x0000000185bc6080+4608 of device mask ffffffff bus mask 0 fddi1: Receive buffer allocation failed fddi1: Adapter open failed! IP-Config: Failed to open fddi1 when memory beyond 4GiB is handed out to devices that can only do 32-bit addressing. This updates commit cce335ae ("[MIPS] 64-bit Sibyte kernels need DMA32."). References: [1] "BCM1250/BCM1125/BCM1125H User Manual", Revision 1250_1125-UM100-R, Broadcom Corporation, 21 Oct 2002, Section 3: "System Overview", "Memory Map", pp. 34-38 [2] "BCM91250A User Manual", Revision 91250A-UM100-R, Broadcom Corporation, 18 May 2004, Section 3: "Physical Description", "Supported DRAM", p. 23 Signed-off-by:
Maciej W. Rozycki <macro@linux-mips.org> [paul.burton@mips.com: Remove GPL text from dma.c; SPDX tag covers it] Signed-off-by:
Paul Burton <paul.burton@mips.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Patchwork: https://patchwork.linux-mips.org/patch/21108/ References: cce335ae ("[MIPS] 64-bit Sibyte kernels need DMA32.") Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Anders Roxell authored
[ Upstream commit 347a28b5 ] This happened while running in qemu-system-aarch64, the AMBA PL011 UART driver when enabling CONFIG_DEBUG_TEST_DRIVER_REMOVE. arch_initcall(pl011_init) came before subsys_initcall(default_bdi_init), devtmpfs' handle_remove() crashes because the reference count is a NULL pointer only because wb->bdi hasn't been initialized yet. Rework so that wb_put have an extra check if wb->bdi before decrement wb->refcnt and also add a WARN_ON_ONCE to get a warning if it happens again in other drivers. Fixes: 52ebea74 ("writeback: make backing_dev_info host cgroup-specific bdi_writebacks") Co-developed-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Anders Roxell <anders.roxell@linaro.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Miroslav Lichvar authored
[ Upstream commit e1f65b0d ] It seems with some NICs supported by the e1000e driver a SYSTIM reading may occasionally be few microseconds before the previous reading and if enabled also pass e1000e_sanitize_systim() without reaching the maximum number of rereads, even if the function is modified to check three consecutive readings (i.e. it doesn't look like a double read error). This causes an underflow in the timecounter and the PHC time jumps hours ahead. This was observed on 82574, I217 and I219. The fastest way to reproduce it is to run a program that continuously calls the PTP_SYS_OFFSET ioctl on the PHC. Modify e1000e_phc_gettime() to use timecounter_cyc2time() instead of timecounter_read() in order to allow non-monotonic SYSTIM readings and prevent the PHC from jumping. Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by:
Miroslav Lichvar <mlichvar@redhat.com> Acked-by:
Jacob Keller <jacob.e.keller@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
João Paulo Rechi Vita authored
[ Upstream commit 78f3ac76 ] In the past, Asus firmwares would change the panel backlight directly through the EC when the display off hotkey (Fn+F7) was pressed, and only notify the OS of such change, with 0x33 when the LCD was ON and 0x34 when the LCD was OFF. These are currently mapped to KEY_DISPLAYTOGGLE and KEY_DISPLAY_OFF, respectively. Most recently the EC on Asus most machines lost ability to toggle the LCD backlight directly, but unless the OS informs the firmware it is going to handle the display toggle hotkey events, the firmware still tries change the brightness through the EC, to no effect. The end result is a long list (at Endless we counted 11) of Asus laptop models where the display toggle hotkey does not perform any action. Our firmware engineers contacts at Asus were surprised that there were still machines out there with the old behavior. Calling WMNB(ASUS_WMI_DEVID_BACKLIGHT==0x00050011, 2) on the _WDG device tells the firmware that it should let the OS handle the display toggle event, in which case it will simply notify the OS of a key press with 0x35, as shown by the DSDT excerpts bellow. Scope (_SB) { (...) Device (ATKD) { (...) Name (_WDG, Buffer (0x28) { /* 0000 */ 0xD0, 0x5E, 0x84, 0x97, 0x6D, 0x4E, 0xDE, 0x11, /* 0008 */ 0x8A, 0x39, 0x08, 0x00, 0x20, 0x0C, 0x9A, 0x66, /* 0010 */ 0x4E, 0x42, 0x01, 0x02, 0x35, 0xBB, 0x3C, 0x0B, /* 0018 */ 0xC2, 0xE3, 0xED, 0x45, 0x91, 0xC2, 0x4C, 0x5A, /* 0020 */ 0x6D, 0x19, 0x5D, 0x1C, 0xFF, 0x00, 0x01, 0x08 }) Method (WMNB, 3, Serialized) { CreateDWordField (Arg2, Zero, IIA0) CreateDWordField (Arg2, 0x04, IIA1) Local0 = (Arg1 & 0xFFFFFFFF) (...) If ((Local0 == 0x53564544)) { (...) If ((IIA0 == 0x00050011)) { If ((IIA1 == 0x02)) { ^^PCI0.SBRG.EC0.SPIN (0x72, One) ^^PCI0.SBRG.EC0.BLCT = One } Return (One) } } (...) } (...) } (...) } (...) Scope (_SB.PCI0.SBRG.EC0) { (...) Name (BLCT, Zero) (...) Method (_Q10, 0, NotSerialized) // _Qxx: EC Query { If ((BLCT == Zero)) { Local0 = One Local0 = RPIN (0x72) Local0 ^= One SPIN (0x72, Local0) If (ATKP) { Local0 = (0x34 - Local0) ^^^^ATKD.IANE (Local0) } } ElseIf ((BLCT == One)) { If (ATKP) { ^^^^ATKD.IANE (0x35) } } } (...) } Signed-off-by:
João Paulo Rechi Vita <jprvita@endlessm.com> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Darrick J. Wong authored
commit 7b38460d upstream. Kanda Motohiro reported that expanding a tiny xattr into a large xattr fails on XFS because we remove the tiny xattr from a shortform fork and then try to re-add it after converting the fork to extents format having not removed the ATTR_REPLACE flag. This fails because the attr is no longer present, causing a fs shutdown. This is derived from the patch in his bug report, but we really shouldn't ignore a nonzero retval from the remove call. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199119 Reported-by: kanda.motohiro@gmail.com Reviewed-by:
Dave Chinner <dchinner@redhat.com> Reviewed-by:
Darrick J. Wong <darrick.wong@oracle.com> Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by:
-
David Ahern authored
[ Upstream commit d4a7e9bb ] I realized the last patch calls dev_get_by_index_rcu in a branch not holding the rcu lock. Add the calls to rcu_read_lock and rcu_read_unlock. Fixes: ec90ad33 ("ipv6: Consider sk_bound_dev_if when binding a socket to a v4 mapped address") Signed-off-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
David Ahern authored
[ Upstream commit ec90ad33 ] Similar to c5ee0663 ("ipv6: Consider sk_bound_dev_if when binding a socket to an address"), binding a socket to v4 mapped addresses needs to consider if the socket is bound to a device. This problem also exists from the beginning of git history. Signed-off-by:
-
Kai-Heng Feng authored
[ Upstream commit 36352991 ] There are two new Realtek Ethernet devices which are re-branded r8168h. Add the IDs to to support them. Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Reviewed-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
commit c06ef2e9 upstream. As reported by smatch: drivers/media/common/videobuf2/videobuf2-core.c: drivers/media/common/videobuf2/videobuf2-core.c:2159 vb2_mmap() warn: inconsistent returns 'mutex:&q->mmap_lock'. Locked on: line 2148 Unlocked on: line 2100 line 2108 line 2113 line 2118 line 2156 line 2159 There is one error condition that doesn't unlock a mutex. Fixes: cd26d1c4 ("media: vb2: vb2_mmap: move lock up") Reviewed-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by:
-
Ivan Mironov authored
commit 66a8d5bf upstream. Strict requirement of pixclock to be zero breaks support of SDL 1.2 which contains hardcoded table of supported video modes with non-zero pixclock values[1]. To better understand which pixclock values are considered valid and how driver should handle these values, I briefly examined few existing fbdev drivers and documentation in Documentation/fb/. And it looks like there are no strict rules on that and actual behaviour varies: * some drivers treat (pixclock == 0) as "use defaults" (uvesafb.c); * some treat (pixclock == 0) as invalid value which leads to -EINVAL (clps711x-fb.c); * some pass converted pixclock value to hardware (uvesafb.c); * some are trying to find nearest value from predefined table (vga16fb.c, video_gx.c). Given this, I believe that it should be safe to just ignore this value if changing is not supported. It seems that any portable fbdev application which was not written only for one specific device working under one specific kernel version should not rely on any particular behaviour of pixclock anyway. However, while enabling SDL1 applications to work out of the box when there is no /etc/fb.modes with valid settings, this change affects the video mode choosing logic in SDL. Depending on current screen resolution, contents of /etc/fb.modes and resolution requested by application, this may lead to user-visible difference (not always): image will be displayed in a right way, but it will be aligned to the left instead of center. There is no "right behaviour" here as well, as emulated fbdev, opposing to old fbdev drivers, simply ignores any requsts of video mode changes with resolutions smaller than current. The easiest way to reproduce this problem is to install sdl-sopwith[2], remove /etc/fb.modes file if it exists, and then try to run sopwith from console without X. At least in Fedora 29, sopwith may be simply installed from standard repositories. [1] SDL 1.2.15 source code, src/video/fbcon/SDL_fbvideo.c, vesa_timings [2] http://sdl-sopwith.sourceforge.net/Signed-off-by:
Ivan Mironov <mironov.ivan@gmail.com> Cc: stable@vger.kernel.org Fixes: 79e53945 ("DRM: i915: add mode setting support") Fixes: 771fe6b9 ("drm/radeon: introduce kernel modesetting for radeon hardware") Fixes: 785b93ef ("drm/kms: move driver specific fb common code to helper functions (v2)") Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20190108072353.28078-3-mironov.ivan@gmail.comSigned-off-by:
-
Tetsuo Handa authored
commit 628bd859 upstream. Commit 0a42e99b ("loop: Get rid of loop_index_mutex") forgot to remove mutex_unlock(&loop_ctl_mutex) from loop_control_ioctl() when replacing loop_index_mutex with loop_ctl_mutex. Fixes: 0a42e99b ("loop: Get rid of loop_index_mutex") Reported-by:
syzbot <syzbot+c0138741c2290fc5e63f@syzkaller.appspotmail.com> Reviewed-by:
Ming Lei <ming.lei@redhat.com> Reviewed-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Jan Kara authored
commit 0a42e99b upstream. Now that loop_ctl_mutex is global, just get rid of loop_index_mutex as there is no good reason to keep these two separate and it just complicates the locking. Signed-off-by:
-
Jan Kara authored
commit 967d1dc1 upstream. __loop_release() has a single call site. Fold it there. This is currently not a huge win but it will make following replacement of loop_index_mutex more obvious. Signed-off-by:
-
Tetsuo Handa authored
commit 310ca162 upstream. syzbot is reporting NULL pointer dereference [1] which is caused by race condition between ioctl(loop_fd, LOOP_CLR_FD, 0) versus ioctl(other_loop_fd, LOOP_SET_FD, loop_fd) due to traversing other loop devices at loop_validate_file() without holding corresponding lo->lo_ctl_mutex locks. Since ioctl() request on loop devices is not frequent operation, we don't need fine grained locking. Let's use global lock in order to allow safe traversal at loop_validate_file(). Note that syzbot is also reporting circular locking dependency between bdev->bd_mutex and lo->lo_ctl_mutex [2] which is caused by calling blkdev_reread_part() with lock held. This patch does not address it. [1] https://syzkaller.appspot.com/bug?id=f3cfe26e785d85f9ee259f385515291d21bd80a3 [2] https://syzkaller.appspot.com/bug?id=bf154052f0eea4bc7712499e4569505907d15889Signed-off-by:
syzbot <syzbot+bf89c128e05dd6c62523@syzkaller.appspotmail.com> Reviewed-by:
-
Ying Xue authored
commit 2753ca5d upstream. BUG: KMSAN: uninit-value in tipc_nl_compat_doit+0x404/0xa10 net/tipc/netlink_compat.c:335 CPU: 0 PID: 4514 Comm: syz-executor485 Not tainted 4.16.0+ #87 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:17 [inline] dump_stack+0x185/0x1d0 lib/dump_stack.c:53 kmsan_report+0x142/0x240 mm/kmsan/kmsan.c:1067 __msan_warning_32+0x6c/0xb0 mm/kmsan/kmsan_instr.c:683 tipc_nl_compat_doit+0x404/0xa10 net/tipc/netlink_compat.c:335 tipc_nl_compat_recv+0x164b/0x2700 net/tipc/netlink_compat.c:1153 genl_family_rcv_msg net/netlink/genetlink.c:599 [inline] genl_rcv_msg+0x1686/0x1810 net/netlink/genetlink.c:624 netlink_rcv_skb+0x378/0x600 net/netlink/af_netlink.c:2447 genl_rcv+0x63/0x80 net/netlink/genetlink.c:635 netlink_unicast_kernel net/netlink/af_netlink.c:1311 [inline] netlink_unicast+0x166b/0x1740 net/netlink/af_netlink.c:1337 netlink_sendmsg+0x1048/0x1310 net/netlink/af_netlink.c:1900 sock_sendmsg_nosec net/socket.c:630 [inline] sock_sendmsg net/socket.c:640 [inline] ___sys_sendmsg+0xec0/0x1310 net/socket.c:2046 __sys_sendmsg net/socket.c:2080 [inline] SYSC_sendmsg+0x2a3/0x3d0 net/socket.c:2091 SyS_sendmsg+0x54/0x80 net/socket.c:2087 do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287 entry_SYSCALL_64_after_hwframe+0x3d/0xa2 RIP: 0033:0x43fda9 RSP: 002b:00007ffd0c184ba8 EFLAGS: 00000213 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 000000000043fda9 RDX: 0000000000000000 RSI: 0000000020023000 RDI: 0000000000000003 RBP: 00000000006ca018 R08: 00000000004002c8 R09: 00000000004002c8 R10: 00000000004002c8 R11: 0000000000000213 R12: 00000000004016d0 R13: 0000000000401760 R14: 0000000000000000 R15: 0000000000000000 Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:278 [inline] kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:188 kmsan_kmalloc+0x94/0x100 mm/kmsan/kmsan.c:314 kmsan_slab_alloc+0x11/0x20 mm/kmsan/kmsan.c:321 slab_post_alloc_hook mm/slab.h:445 [inline] slab_alloc_node mm/slub.c:2737 [inline] __kmalloc_node_track_caller+0xaed/0x11c0 mm/slub.c:4369 __kmalloc_reserve net/core/skbuff.c:138 [inline] __alloc_skb+0x2cf/0x9f0 net/core/skbuff.c:206 alloc_skb include/linux/skbuff.h:984 [inline] netlink_alloc_large_skb net/netlink/af_netlink.c:1183 [inline] netlink_sendmsg+0x9a6/0x1310 net/netlink/af_netlink.c:1875 sock_sendmsg_nosec net/socket.c:630 [inline] sock_sendmsg net/socket.c:640 [inline] ___sys_sendmsg+0xec0/0x1310 net/socket.c:2046 __sys_sendmsg net/socket.c:2080 [inline] SYSC_sendmsg+0x2a3/0x3d0 net/socket.c:2091 SyS_sendmsg+0x54/0x80 net/socket.c:2087 do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287 entry_SYSCALL_64_after_hwframe+0x3d/0xa2 In tipc_nl_compat_recv(), when the len variable returned by nlmsg_attrlen() is 0, the message is still treated as a valid one, which is obviously unresonable. When len is zero, it means the message not only doesn't contain any valid TLV payload, but also TLV header is not included. Under this stituation, tlv_type field in TLV header is still accessed in tipc_nl_compat_dumpit() or tipc_nl_compat_doit(), but the field space is obviously illegal. Of course, it is not initialized. Reported-by: syzbot+bca0dc46634781f08b38@syzkaller.appspotmail.com Reported-by: syzbot+6bdb590321a7ae40c1a6@syzkaller.appspotmail.com Signed-off-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
-
Ying Xue authored
commit 974cb0e3 upstream. syzbot reported: BUG: KMSAN: uninit-value in __arch_swab32 arch/x86/include/uapi/asm/swab.h:10 [inline] BUG: KMSAN: uninit-value in __fswab32 include/uapi/linux/swab.h:59 [inline] BUG: KMSAN: uninit-value in tipc_nl_compat_name_table_dump+0x4a8/0xba0 net/tipc/netlink_compat.c:826 CPU: 0 PID: 6290 Comm: syz-executor848 Not tainted 4.19.0-rc8+ #70 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x306/0x460 lib/dump_stack.c:113 kmsan_report+0x1a2/0x2e0 mm/kmsan/kmsan.c:917 __msan_warning+0x7c/0xe0 mm/kmsan/kmsan_instr.c:500 __arch_swab32 arch/x86/include/uapi/asm/swab.h:10 [inline] __fswab32 include/uapi/linux/swab.h:59 [inline] tipc_nl_compat_name_table_dump+0x4a8/0xba0 net/tipc/netlink_compat.c:826 __tipc_nl_compat_dumpit+0x59e/0xdb0 net/tipc/netlink_compat.c:205 tipc_nl_compat_dumpit+0x63a/0x820 net/tipc/netlink_compat.c:270 tipc_nl_compat_handle net/tipc/netlink_compat.c:1151 [inline] tipc_nl_compat_recv+0x1402/0x2760 net/tipc/netlink_compat.c:1210 genl_family_rcv_msg net/netlink/genetlink.c:601 [inline] genl_rcv_msg+0x185c/0x1a20 net/netlink/genetlink.c:626 netlink_rcv_skb+0x394/0x640 net/netlink/af_netlink.c:2454 genl_rcv+0x63/0x80 net/netlink/genetlink.c:637 netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline] netlink_unicast+0x166d/0x1720 net/netlink/af_netlink.c:1343 netlink_sendmsg+0x1391/0x1420 net/netlink/af_netlink.c:1908 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg net/socket.c:631 [inline] ___sys_sendmsg+0xe47/0x1200 net/socket.c:2116 __sys_sendmsg net/socket.c:2154 [inline] __do_sys_sendmsg net/socket.c:2163 [inline] __se_sys_sendmsg+0x307/0x460 net/socket.c:2161 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2161 do_syscall_64+0xbe/0x100 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 RIP: 0033:0x440179 Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 fb 13 fc ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007ffecec49318 EFLAGS: 00000213 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 0000000000440179 RDX: 0000000000000000 RSI: 0000000020000100 RDI: 0000000000000003 RBP: 00000000006ca018 R08: 0000000000000000 R09: 00000000004002c8 R10: 0000000000000000 R11: 0000000000000213 R12: 0000000000401a00 R13: 0000000000401a90 R14: 0000000000000000 R15: 0000000000000000 Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:255 [inline] kmsan_internal_poison_shadow+0xc8/0x1d0 mm/kmsan/kmsan.c:180 kmsan_kmalloc+0xa4/0x120 mm/kmsan/kmsan_hooks.c:104 kmsan_slab_alloc+0x10/0x20 mm/kmsan/kmsan_hooks.c:113 slab_post_alloc_hook mm/slab.h:446 [inline] slab_alloc_node mm/slub.c:2727 [inline] __kmalloc_node_track_caller+0xb43/0x1400 mm/slub.c:4360 __kmalloc_reserve net/core/skbuff.c:138 [inline] __alloc_skb+0x422/0xe90 net/core/skbuff.c:206 alloc_skb include/linux/skbuff.h:996 [inline] netlink_alloc_large_skb net/netlink/af_netlink.c:1189 [inline] netlink_sendmsg+0xcaf/0x1420 net/netlink/af_netlink.c:1883 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg net/socket.c:631 [inline] ___sys_sendmsg+0xe47/0x1200 net/socket.c:2116 __sys_sendmsg net/socket.c:2154 [inline] __do_sys_sendmsg net/socket.c:2163 [inline] __se_sys_sendmsg+0x307/0x460 net/socket.c:2161 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2161 do_syscall_64+0xbe/0x100 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 We cannot take for granted the thing that the length of data contained in TLV is longer than the size of struct tipc_name_table_query in tipc_nl_compat_name_table_dump(). Reported-by: syzbot+06e771a754829716a327@syzkaller.appspotmail.com Signed-off-by:
-
Ying Xue authored
commit edf5ff04 upstream. syzbot reports following splat: BUG: KMSAN: uninit-value in strlen+0x3b/0xa0 lib/string.c:486 CPU: 1 PID: 9306 Comm: syz-executor172 Not tainted 4.20.0-rc7+ #2 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x173/0x1d0 lib/dump_stack.c:113 kmsan_report+0x12e/0x2a0 mm/kmsan/kmsan.c:613 __msan_warning+0x82/0xf0 mm/kmsan/kmsan_instr.c:313 strlen+0x3b/0xa0 lib/string.c:486 nla_put_string include/net/netlink.h:1154 [inline] __tipc_nl_compat_link_set net/tipc/netlink_compat.c:708 [inline] tipc_nl_compat_link_set+0x929/0x1220 net/tipc/netlink_compat.c:744 __tipc_nl_compat_doit net/tipc/netlink_compat.c:311 [inline] tipc_nl_compat_doit+0x3aa/0xaf0 net/tipc/netlink_compat.c:344 tipc_nl_compat_handle net/tipc/netlink_compat.c:1107 [inline] tipc_nl_compat_recv+0x14d7/0x2760 net/tipc/netlink_compat.c:1210 genl_family_rcv_msg net/netlink/genetlink.c:601 [inline] genl_rcv_msg+0x185f/0x1a60 net/netlink/genetlink.c:626 netlink_rcv_skb+0x444/0x640 net/netlink/af_netlink.c:2477 genl_rcv+0x63/0x80 net/netlink/genetlink.c:637 netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline] netlink_unicast+0xf40/0x1020 net/netlink/af_netlink.c:1336 netlink_sendmsg+0x127f/0x1300 net/netlink/af_netlink.c:1917 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg net/socket.c:631 [inline] ___sys_sendmsg+0xdb9/0x11b0 net/socket.c:2116 __sys_sendmsg net/socket.c:2154 [inline] __do_sys_sendmsg net/socket.c:2163 [inline] __se_sys_sendmsg+0x305/0x460 net/socket.c:2161 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2161 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 The uninitialised access happened in nla_put_string(skb, TIPC_NLA_LINK_NAME, lc->name) This is because lc->name string is not validated before it's used. Reported-by: syzbot+d78b8a29241a195aefb8@syzkaller.appspotmail.com Signed-off-by:
-
Ying Xue authored
commit 0762216c upstream. syzbot reported: BUG: KMSAN: uninit-value in strlen+0x3b/0xa0 lib/string.c:484 CPU: 1 PID: 6371 Comm: syz-executor652 Not tainted 4.19.0-rc8+ #70 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x306/0x460 lib/dump_stack.c:113 kmsan_report+0x1a2/0x2e0 mm/kmsan/kmsan.c:917 __msan_warning+0x7c/0xe0 mm/kmsan/kmsan_instr.c:500 strlen+0x3b/0xa0 lib/string.c:484 nla_put_string include/net/netlink.h:1011 [inline] tipc_nl_compat_bearer_enable+0x238/0x7b0 net/tipc/netlink_compat.c:389 __tipc_nl_compat_doit net/tipc/netlink_compat.c:311 [inline] tipc_nl_compat_doit+0x39f/0xae0 net/tipc/netlink_compat.c:344 tipc_nl_compat_recv+0x147c/0x2760 net/tipc/netlink_compat.c:1107 genl_family_rcv_msg net/netlink/genetlink.c:601 [inline] genl_rcv_msg+0x185c/0x1a20 net/netlink/genetlink.c:626 netlink_rcv_skb+0x394/0x640 net/netlink/af_netlink.c:2454 genl_rcv+0x63/0x80 net/netlink/genetlink.c:637 netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline] netlink_unicast+0x166d/0x1720 net/netlink/af_netlink.c:1343 netlink_sendmsg+0x1391/0x1420 net/netlink/af_netlink.c:1908 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg net/socket.c:631 [inline] ___sys_sendmsg+0xe47/0x1200 net/socket.c:2116 __sys_sendmsg net/socket.c:2154 [inline] __do_sys_sendmsg net/socket.c:2163 [inline] __se_sys_sendmsg+0x307/0x460 net/socket.c:2161 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2161 do_syscall_64+0xbe/0x100 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 RIP: 0033:0x440179 Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 fb 13 fc ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007fffef7beee8 EFLAGS: 00000213 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 0000000000440179 RDX: 0000000000000000 RSI: 0000000020000100 RDI: 0000000000000003 RBP: 00000000006ca018 R08: 0000000000000000 R09: 00000000004002c8 R10: 0000000000000000 R11: 0000000000000213 R12: 0000000000401a00 R13: 0000000000401a90 R14: 0000000000000000 R15: 0000000000000000 Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:255 [inline] kmsan_internal_poison_shadow+0xc8/0x1d0 mm/kmsan/kmsan.c:180 kmsan_kmalloc+0xa4/0x120 mm/kmsan/kmsan_hooks.c:104 kmsan_slab_alloc+0x10/0x20 mm/kmsan/kmsan_hooks.c:113 slab_post_alloc_hook mm/slab.h:446 [inline] slab_alloc_node mm/slub.c:2727 [inline] __kmalloc_node_track_caller+0xb43/0x1400 mm/slub.c:4360 __kmalloc_reserve net/core/skbuff.c:138 [inline] __alloc_skb+0x422/0xe90 net/core/skbuff.c:206 alloc_skb include/linux/skbuff.h:996 [inline] netlink_alloc_large_skb net/netlink/af_netlink.c:1189 [inline] netlink_sendmsg+0xcaf/0x1420 net/netlink/af_netlink.c:1883 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg net/socket.c:631 [inline] ___sys_sendmsg+0xe47/0x1200 net/socket.c:2116 __sys_sendmsg net/socket.c:2154 [inline] __do_sys_sendmsg net/socket.c:2163 [inline] __se_sys_sendmsg+0x307/0x460 net/socket.c:2161 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2161 do_syscall_64+0xbe/0x100 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 The root cause is that we don't validate whether bear name is a valid string in tipc_nl_compat_bearer_enable(). Meanwhile, we also fix the same issue in the following functions: tipc_nl_compat_bearer_disable() tipc_nl_compat_link_stat_dump() tipc_nl_compat_media_set() tipc_nl_compat_bearer_set() Reported-by: syzbot+b33d5cae0efd35dbfe77@syzkaller.appspotmail.com Signed-off-by:
-
Ying Xue authored
commit 8b66fee7 upstream. syzbot reports following splat: BUG: KMSAN: uninit-value in strlen+0x3b/0xa0 lib/string.c:486 CPU: 1 PID: 11057 Comm: syz-executor0 Not tainted 4.20.0-rc7+ #2 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x173/0x1d0 lib/dump_stack.c:113 kmsan_report+0x12e/0x2a0 mm/kmsan/kmsan.c:613 __msan_warning+0x82/0xf0 mm/kmsan/kmsan_instr.c:295 strlen+0x3b/0xa0 lib/string.c:486 nla_put_string include/net/netlink.h:1154 [inline] tipc_nl_compat_link_reset_stats+0x1f0/0x360 net/tipc/netlink_compat.c:760 __tipc_nl_compat_doit net/tipc/netlink_compat.c:311 [inline] tipc_nl_compat_doit+0x3aa/0xaf0 net/tipc/netlink_compat.c:344 tipc_nl_compat_handle net/tipc/netlink_compat.c:1107 [inline] tipc_nl_compat_recv+0x14d7/0x2760 net/tipc/netlink_compat.c:1210 genl_family_rcv_msg net/netlink/genetlink.c:601 [inline] genl_rcv_msg+0x185f/0x1a60 net/netlink/genetlink.c:626 netlink_rcv_skb+0x444/0x640 net/netlink/af_netlink.c:2477 genl_rcv+0x63/0x80 net/netlink/genetlink.c:637 netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline] netlink_unicast+0xf40/0x1020 net/netlink/af_netlink.c:1336 netlink_sendmsg+0x127f/0x1300 net/netlink/af_netlink.c:1917 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg net/socket.c:631 [inline] ___sys_sendmsg+0xdb9/0x11b0 net/socket.c:2116 __sys_sendmsg net/socket.c:2154 [inline] __do_sys_sendmsg net/socket.c:2163 [inline] __se_sys_sendmsg+0x305/0x460 net/socket.c:2161 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2161 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 RIP: 0033:0x457ec9 Code: 6d b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 3b b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007f2557338c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000457ec9 RDX: 0000000000000000 RSI: 00000000200001c0 RDI: 0000000000000003 RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f25573396d4 R13: 00000000004cb478 R14: 00000000004d86c8 R15: 00000000ffffffff Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:204 [inline] kmsan_internal_poison_shadow+0x92/0x150 mm/kmsan/kmsan.c:158 kmsan_kmalloc+0xa6/0x130 mm/kmsan/kmsan_hooks.c:176 kmsan_slab_alloc+0xe/0x10 mm/kmsan/kmsan_hooks.c:185 slab_post_alloc_hook mm/slab.h:446 [inline] slab_alloc_node mm/slub.c:2759 [inline] __kmalloc_node_track_caller+0xe18/0x1030 mm/slub.c:4383 __kmalloc_reserve net/core/skbuff.c:137 [inline] __alloc_skb+0x309/0xa20 net/core/skbuff.c:205 alloc_skb include/linux/skbuff.h:998 [inline] netlink_alloc_large_skb net/netlink/af_netlink.c:1182 [inline] netlink_sendmsg+0xb82/0x1300 net/netlink/af_netlink.c:1892 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg net/socket.c:631 [inline] ___sys_sendmsg+0xdb9/0x11b0 net/socket.c:2116 __sys_sendmsg net/socket.c:2154 [inline] __do_sys_sendmsg net/socket.c:2163 [inline] __se_sys_sendmsg+0x305/0x460 net/socket.c:2161 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2161 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 The uninitialised access happened in tipc_nl_compat_link_reset_stats: nla_put_string(skb, TIPC_NLA_LINK_NAME, name) This is because name string is not validated before it's used. Reported-by: syzbot+e01d94b5a4c266be6e4c@syzkaller.appspotmail.com Signed-off-by:
-
Xin Long authored
commit 400b8b9a upstream. The similar issue as fixed in Commit 4a2eb0c3 ("sctp: initialize sin6_flowinfo for ipv6 addrs in sctp_inet6addr_event") also exists in sctp_inetaddr_event, as Alexander noticed. To fix it, allocate sctp_sockaddr_entry with kzalloc for both sctp ipv4 and ipv6 addresses, as does in sctp_v4/6_copy_addrlist(). Reported-by:
Alexander Potapenko <glider@google.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Reported-by: syzbot+ae0c70c0c2d40c51bb92@syzkaller.appspotmail.com Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Stephen Smalley authored
commit 5b0e7310 upstream. levdatum->level can be NULL if we encounter an error while loading the policy during sens_read prior to initializing it. Make sure sens_destroy handles that case correctly. Reported-by: syzbot+6664500f0f18f07a5c0e@syzkaller.appspotmail.com Signed-off-by:
Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
-
J. Bruce Fields authored
commit 81c88b18 upstream. If we ignore the error we'll hit a null dereference a little later. Reported-by: syzbot+4b98281f2401ab849f4b@syzkaller.appspotmail.com Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by:
-
Hans Verkuil authored
commit cd26d1c4 upstream. If a filehandle is dup()ped, then it is possible to close it from one fd and call mmap from the other. This creates a race condition in vb2_mmap where it is using queue data that __vb2_queue_free (called from close()) is in the process of releasing. By moving up the mutex_lock(mmap_lock) in vb2_mmap this race is avoided since __vb2_queue_free is called with the same mutex locked. So vb2_mmap now reads consistent buffer data. Signed-off-by:
Hans Verkuil <hverkuil@xs4all.nl> Reported-by: syzbot+be93025dd45dccd8923c@syzkaller.appspotmail.com Signed-off-by:
Hans Verkuil <hansverk@cisco.com> Signed-off-by:
-
James Morris authored
commit a5795fd3 upstream. From: Casey Schaufler <casey@schaufler-ca.com> Check that the cred security blob has been set before trying to clean it up. There is a case during credential initialization that could result in this. Signed-off-by:
Casey Schaufler <casey@schaufler-ca.com> Acked-by:
John Johansen <john.johansen@canonical.com> Signed-off-by:
James Morris <james.morris@microsoft.com> Reported-by: syzbot+69ca07954461f189e808@syzkaller.appspotmail.com Signed-off-by:
-
Hans Verkuil authored
commit 9729d6d2 upstream. The capture DV timings capabilities allowed for a minimum width and height of 0. So passing a timings struct with 0 values is allowed and will later cause a division by zero. Ensure that the width and height must be >= 16 to avoid this. Signed-off-by:
-
Hans Verkuil authored
commit 701f49bc upstream. kthread_run returns an error pointer, but elsewhere in the code dev->kthread_vid_cap/out is checked against NULL. If kthread_run returns an error, then set the pointer to NULL. I chose this method over changing all kthread_vid_cap/out tests elsewhere since this is more robust. Signed-off-by:
-
Vlad Tsyrklevich authored
commit a01421e4 upstream. Using [1] for static analysis I found that the OMAPFB_QUERY_PLANE, OMAPFB_GET_COLOR_KEY, OMAPFB_GET_DISPLAY_INFO, and OMAPFB_GET_VRAM_INFO cases could all leak uninitialized stack memory--either due to uninitialized padding or 'reserved' fields. Fix them by clearing the shared union used to store copied out data. [1] https://github.com/vlad902/kernel-uninitialized-memory-checkerSigned-off-by:
Vlad Tsyrklevich <vlad@tsyrklevich.net> Reviewed-by:
Kees Cook <keescook@chromium.org> Fixes: b39a982d ("OMAP: DSS2: omapfb driver") Cc: security@kernel.org [b.zolnierkie: prefix patch subject with "omap2fb: "] Signed-off-by:
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by:
-
YunQiang Su authored
commit a214720c upstream. Octeon has an boot-time option to disable pcie. Since MSI depends on PCI-E, we should also disable MSI also with this option is on in order to avoid inadvertently accessing PCIe registers. Signed-off-by:
YunQiang Su <ysu@wavecomp.com> Signed-off-by:
-
Jonathan Hunter authored
commit ac4ca4b9 upstream. The tps6586x driver creates an irqchip that is used by its various child devices for managing interrupts. The tps6586x-rtc device is one of its children that uses the tps6586x irqchip. When using the tps6586x-rtc as a wake-up device from suspend, the following is seen: PM: Syncing filesystems ... done. Freezing user space processes ... (elapsed 0.001 seconds) done. OOM killer disabled. Freezing remaining freezable tasks ... (elapsed 0.000 seconds) done. Disabling non-boot CPUs ... Entering suspend state LP1 Enabling non-boot CPUs ... CPU1 is up tps6586x 3-0034: failed to read interrupt status tps6586x 3-0034: failed to read interrupt status The reason why the tps6586x interrupt status cannot be read is because the tps6586x interrupt is not masked during suspend and when the tps6586x-rtc interrupt occurs, to wake-up the device, the interrupt is seen before the i2c controller has been resumed in order to read the tps6586x interrupt status. The tps6586x-rtc driver sets it's interrupt as a wake-up source during suspend, which gets propagated to the parent tps6586x interrupt. However, the tps6586x-rtc driver cannot disable it's interrupt during suspend otherwise we would never be woken up and so the tps6586x must disable it's interrupt instead. Prevent the tps6586x interrupt handler from executing on exiting suspend before the i2c controller has been resumed by disabling the tps6586x interrupt on entering suspend and re-enabling it on resuming from suspend. Cc: stable@vger.kernel.org Signed-off-by:
Jon Hunter <jonathanh@nvidia.com> Reviewed-by:
Dmitry Osipenko <digetx@gmail.com> Tested-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Arnd Bergmann authored
commit 5a9372f7 upstream. While reading through the sysvipc implementation, I noticed that the n32 semctl/shmctl/msgctl system calls behave differently based on whether o32 support is enabled or not: Without o32, the IPC_64 flag passed by user space is rejected but calls without that flag get IPC_64 behavior. As far as I can tell, this was inadvertently changed by a cleanup patch but never noticed by anyone, possibly nobody has tried using sysvipc on n32 after linux-3.19. Change it back to the old behavior now. Fixes: 78aaf956 ("MIPS: Compat: Fix build error if CONFIG_MIPS32_COMPAT but no compat ABI.") Signed-off-by:
-
Ivan Mironov authored
commit 44759979 upstream. Changing of caching mode via /sys/devices/.../scsi_disk/.../cache_type may fail if device responds to MODE SENSE command with DPOFUA flag set, and then checks this flag to be not set on MODE SELECT command. In this scenario, when trying to change cache_type, write always fails: # echo "none" >cache_type bash: echo: write error: Invalid argument And following appears in dmesg: [13007.865745] sd 1:0:1:0: [sda] Sense Key : Illegal Request [current] [13007.865753] sd 1:0:1:0: [sda] Add. Sense: Invalid field in parameter list From SBC-4 r15, 6.5.1 "Mode pages overview", description of DEVICE-SPECIFIC PARAMETER field in the mode parameter header: ... The write protect (WP) bit for mode data sent with a MODE SELECT command shall be ignored by the device server. ... The DPOFUA bit is reserved for mode data sent with a MODE SELECT command. ... The remaining bits in the DEVICE-SPECIFIC PARAMETER byte are also reserved and shall be set to zero. [mkp: shuffled commentary to commit description] Cc: stable@vger.kernel.org Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Kees Cook authored
commit 9474f4e7 upstream. It's possible that a pid has died before we take the rcu lock, in which case we can't walk the ancestry list as it may be detached. Instead, check for death first before doing the walk. Reported-by: syzbot+a9ac39bf55329e206219@syzkaller.appspotmail.com Fixes: 2d514487 ("security: Yama LSM") Cc: stable@vger.kernel.org Suggested-by:
Oleg Nesterov <oleg@redhat.com> Signed-off-by:
-
Josef Bacik authored
commit 74d5d229 upstream. If we flip read-only before we initiate writeback on all dirty pages for ordered extents we've created then we'll have ordered extents left over on umount, which results in all sorts of bad things happening. Fix this by making sure we wait on ordered extents if we have to do the aborted transaction cleanup stuff. generic/475 can produce this warning: [ 8531.177332] WARNING: CPU: 2 PID: 11997 at fs/btrfs/disk-io.c:3856 btrfs_free_fs_root+0x95/0xa0 [btrfs] [ 8531.183282] CPU: 2 PID: 11997 Comm: umount Tainted: G W 5.0.0-rc1-default+ #394 [ 8531.185164] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),BIOS rel-1.11.2-0-gf9626cc-prebuilt.qemu-project.org 04/01/2014 [ 8531.187851] RIP: 0010:btrfs_free_fs_root+0x95/0xa0 [btrfs] [ 8531.193082] RSP: 0018:ffffb1ab86163d98 EFLAGS: 00010286 [ 8531.194198] RAX: ffff9f3449494d18 RBX: ffff9f34a2695000 RCX:0000000000000000 [ 8531.195629] RDX: 0000000000000002 RSI: 0000000000000001 RDI:0000000000000000 [ 8531.197315] RBP: ffff9f344e930000 R08: 0000000000000001 R09:0000000000000000 [ 8531.199095] R10: 0000000000000000 R11: ffff9f34494d4ff8 R12:ffffb1ab86163dc0 [ 8531.200870] R13: ffff9f344e9300b0 R14: ffffb1ab86163db8 R15:0000000000000000 [ 8531.202707] FS: 00007fc68e949fc0(0000) GS:ffff9f34bd800000(0000)knlGS:0000000000000000 [ 8531.204851] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 8531.205942] CR2: 00007ffde8114dd8 CR3: 000000002dfbd000 CR4:00000000000006e0 [ 8531.207516] Call Trace: [ 8531.208175] btrfs_free_fs_roots+0xdb/0x170 [btrfs] [ 8531.210209] ? wait_for_completion+0x5b/0x190 [ 8531.211303] close_ctree+0x157/0x350 [btrfs] [ 8531.212412] generic_shutdown_super+0x64/0x100 [ 8531.213485] kill_anon_super+0x14/0x30 [ 8531.214430] btrfs_kill_super+0x12/0xa0 [btrfs] [ 8531.215539] deactivate_locked_super+0x29/0x60 [ 8531.216633] cleanup_mnt+0x3b/0x70 [ 8531.217497] task_work_run+0x98/0xc0 [ 8531.218397] exit_to_usermode_loop+0x83/0x90 [ 8531.219324] do_syscall_64+0x15b/0x180 [ 8531.220192] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 8531.221286] RIP: 0033:0x7fc68e5e4d07 [ 8531.225621] RSP: 002b:00007ffde8116608 EFLAGS: 00000246 ORIG_RAX:00000000000000a6 [ 8531.227512] RAX: 0000000000000000 RBX: 00005580c2175970 RCX:00007fc68e5e4d07 [ 8531.229098] RDX: 0000000000000001 RSI: 0000000000000000 RDI:00005580c2175b80 [ 8531.230730] RBP: 0000000000000000 R08: 00005580c2175ba0 R09:00007ffde8114e80 [ 8531.232269] R10: 0000000000000000 R11: 0000000000000246 R12:00005580c2175b80 [ 8531.233839] R13: 00007fc68eac61c4 R14: 00005580c2175a68 R15:0000000000000000 Leaving a tree in the rb-tree: 3853 void btrfs_free_fs_root(struct btrfs_root *root) 3854 { 3855 iput(root->ino_cache_inode); 3856 WARN_ON(!RB_EMPTY_ROOT(&root->inode_tree)); CC: stable@vger.kernel.org Reviewed-by:
Nikolay Borisov <nborisov@suse.com> Signed-off-by:
Josef Bacik <josef@toxicpanda.com> [ add stacktrace ] Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
Eric Biggers authored
commit 8f9c4693 upstream. Keys for "authenc" AEADs are formatted as an rtattr containing a 4-byte 'enckeylen', followed by an authentication key and an encryption key. crypto_authenc_extractkeys() parses the key to find the inner keys. However, it fails to consider the case where the rtattr's payload is longer than 4 bytes but not 4-byte aligned, and where the key ends before the next 4-byte aligned boundary. In this case, 'keylen -= RTA_ALIGN(rta->rta_len);' underflows to a value near UINT_MAX. This causes a buffer overread and crash during crypto_ahash_setkey(). Fix it by restricting the rtattr payload to the expected size. Reproducer using AF_ALG: #include <linux/if_alg.h> #include <linux/rtnetlink.h> #include <sys/socket.h> int main() { int fd; struct sockaddr_alg addr = { .salg_type = "aead", .salg_name = "authenc(hmac(sha256),cbc(aes))", }; struct { struct rtattr attr; __be32 enckeylen; char keys[1]; } __attribute__((packed)) key = { .attr.rta_len = sizeof(key), .attr.rta_type = 1 /* CRYPTO_AUTHENC_KEYA_PARAM */, }; fd = socket(AF_ALG, SOCK_SEQPACKET, 0); bind(fd, (void *)&addr, sizeof(addr)); setsockopt(fd, SOL_ALG, ALG_SET_KEY, &key, sizeof(key)); } It caused: BUG: unable to handle kernel paging request at ffff88007ffdc000 PGD 2e01067 P4D 2e01067 PUD 2e04067 PMD 2e05067 PTE 0 Oops: 0000 [#1] SMP CPU: 0 PID: 883 Comm: authenc Not tainted 4.20.0-rc1-00108-g00c9fe37 #13 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-20181126_142135-anatol 04/01/2014 RIP: 0010:sha256_ni_transform+0xb3/0x330 arch/x86/crypto/sha256_ni_asm.S:155 [...] Call Trace: sha256_ni_finup+0x10/0x20 arch/x86/crypto/sha256_ssse3_glue.c:321 crypto_shash_finup+0x1a/0x30 crypto/shash.c:178 shash_digest_unaligned+0x45/0x60 crypto/shash.c:186 crypto_shash_digest+0x24/0x40 crypto/shash.c:202 hmac_setkey+0x135/0x1e0 crypto/hmac.c:66 crypto_shash_setkey+0x2b/0xb0 crypto/shash.c:66 shash_async_setkey+0x10/0x20 crypto/shash.c:223 crypto_ahash_setkey+0x2d/0xa0 crypto/ahash.c:202 crypto_authenc_setkey+0x68/0x100 crypto/authenc.c:96 crypto_aead_setkey+0x2a/0xc0 crypto/aead.c:62 aead_setkey+0xc/0x10 crypto/algif_aead.c:526 alg_setkey crypto/af_alg.c:223 [inline] alg_setsockopt+0xfe/0x130 crypto/af_alg.c:256 __sys_setsockopt+0x6d/0xd0 net/socket.c:1902 __do_sys_setsockopt net/socket.c:1913 [inline] __se_sys_setsockopt net/socket.c:1910 [inline] __x64_sys_setsockopt+0x1f/0x30 net/socket.c:1910 do_syscall_64+0x4a/0x180 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe Fixes: e236d4a8 ("[CRYPTO] authenc: Move enckeylen into key itself") Cc: <stable@vger.kernel.org> # v2.6.25+ Signed-off-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Harsh Jain authored
commit a7773363 upstream. Authencesn template in decrypt path unconditionally calls aead_request_complete after ahash_verify which leads to following kernel panic in after decryption. [ 338.539800] BUG: unable to handle kernel NULL pointer dereference at 0000000000000004 [ 338.548372] PGD 0 P4D 0 [ 338.551157] Oops: 0000 [#1] SMP PTI [ 338.554919] CPU: 0 PID: 0 Comm: swapper/0 Kdump: loaded Tainted: G W I 4.19.7+ #13 [ 338.564431] Hardware name: Supermicro X8ST3/X8ST3, BIOS 2.0 07/29/10 [ 338.572212] RIP: 0010:esp_input_done2+0x350/0x410 [esp4] [ 338.578030] Code: ff 0f b6 68 10 48 8b 83 c8 00 00 00 e9 8e fe ff ff 8b 04 25 04 00 00 00 83 e8 01 48 98 48 8b 3c c5 10 00 00 00 e9 f7 fd ff ff <8b> 04 25 04 00 00 00 83 e8 01 48 98 4c 8b 24 c5 10 00 00 00 e9 3b [ 338.598547] RSP: 0018:ffff911c97803c00 EFLAGS: 00010246 [ 338.604268] RAX: 0000000000000002 RBX: ffff911c4469ee00 RCX: 0000000000000000 [ 338.612090] RDX: 0000000000000000 RSI: 0000000000000130 RDI: ffff911b87c20400 [ 338.619874] RBP: 0000000000000000 R08: ffff911b87c20498 R09: 000000000000000a [ 338.627610] R10: 0000000000000001 R11: 0000000000000004 R12: 0000000000000000 [ 338.635402] R13: ffff911c89590000 R14: ffff911c91730000 R15: 0000000000000000 [ 338.643234] FS: 0000000000000000(0000) GS:ffff911c97800000(0000) knlGS:0000000000000000 [ 338.652047] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 338.658299] CR2: 0000000000000004 CR3: 00000001ec20a000 CR4: 00000000000006f0 [ 338.666382] Call Trace: [ 338.669051] <IRQ> [ 338.671254] esp_input_done+0x12/0x20 [esp4] [ 338.675922] chcr_handle_resp+0x3b5/0x790 [chcr] [ 338.680949] cpl_fw6_pld_handler+0x37/0x60 [chcr] [ 338.686080] chcr_uld_rx_handler+0x22/0x50 [chcr] [ 338.691233] uldrx_handler+0x8c/0xc0 [cxgb4] [ 338.695923] process_responses+0x2f0/0x5d0 [cxgb4] [ 338.701177] ? bitmap_find_next_zero_area_off+0x3a/0x90 [ 338.706882] ? matrix_alloc_area.constprop.7+0x60/0x90 [ 338.712517] ? apic_update_irq_cfg+0x82/0xf0 [ 338.717177] napi_rx_handler+0x14/0xe0 [cxgb4] [ 338.722015] net_rx_action+0x2aa/0x3e0 [ 338.726136] __do_softirq+0xcb/0x280 [ 338.730054] irq_exit+0xde/0xf0 [ 338.733504] do_IRQ+0x54/0xd0 [ 338.736745] common_interrupt+0xf/0xf Fixes: 104880a6 ("crypto: authencesn - Convert to new AEAD...") Signed-off-by:
Harsh Jain <harsh@chelsio.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Willem de Bruijn authored
[ Upstream commit 4a06fa67 ] Commit 2efd4fca ("ip: in cmsg IP(V6)_ORIGDSTADDR call pskb_may_pull") avoided a read beyond the end of the skb linear segment by calling pskb_may_pull. That function can trigger a BUG_ON in pskb_expand_head if the skb is shared, which it is when when peeking. It can also return ENOMEM. Avoid both by switching to safer skb_header_pointer. Fixes: 2efd4fca ("ip: in cmsg IP(V6)_ORIGDSTADDR call pskb_may_pull") Reported-by:
syzbot <syzkaller@googlegroups.com> Suggested-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Jason Gunthorpe authored
[ Upstream commit d972f3dc ] 'dev' is non NULL when the addr_len check triggers so it must goto a label that does the dev_put otherwise dev will have a leaked refcount. This bug causes the ib_ipoib module to become unloadable when using systemd-network as it triggers this check on InfiniBand links. Fixes: 99137b78 ("packet: validate address length") Reported-by:
Leon Romanovsky <leonro@mellanox.com> Signed-off-by:
Jason Gunthorpe <jgg@mellanox.com> Acked-by:
-
JianJhen Chen authored
[ Upstream commit 4c84edc1 ] When handling DNAT'ed packets on a bridge device, the neighbour cache entry from lookup was used without checking its state. It means that a cache entry in the NUD_STALE state will be used directly instead of entering the NUD_DELAY state to confirm the reachability of the neighbor. This problem becomes worse after commit 2724680b ("neigh: Keep neighbour cache entries if number of them is small enough."), since all neighbour cache entries in the NUD_STALE state will be kept in the neighbour table as long as the number of cache entries does not exceed the value specified in gc_thresh1. This commit validates the state of a neighbour cache entry before using the entry. Signed-off-by:
JianJhen Chen <kchen@synology.com> Reviewed-by:
JinLin Chen <jlchen@synology.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 7d033c9f ] This patch makes sure the flow label in the IPv6 header forged in ipv6_local_error() is initialized. BUG: KMSAN: kernel-infoleak in _copy_to_user+0x16b/0x1f0 lib/usercopy.c:32 CPU: 1 PID: 24675 Comm: syz-executor1 Not tainted 4.20.0-rc7+ #4 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x173/0x1d0 lib/dump_stack.c:113 kmsan_report+0x12e/0x2a0 mm/kmsan/kmsan.c:613 kmsan_internal_check_memory+0x455/0xb00 mm/kmsan/kmsan.c:675 kmsan_copy_to_user+0xab/0xc0 mm/kmsan/kmsan_hooks.c:601 _copy_to_user+0x16b/0x1f0 lib/usercopy.c:32 copy_to_user include/linux/uaccess.h:177 [inline] move_addr_to_user+0x2e9/0x4f0 net/socket.c:227 ___sys_recvmsg+0x5d7/0x1140 net/socket.c:2284 __sys_recvmsg net/socket.c:2327 [inline] __do_sys_recvmsg net/socket.c:2337 [inline] __se_sys_recvmsg+0x2fa/0x450 net/socket.c:2334 __x64_sys_recvmsg+0x4a/0x70 net/socket.c:2334 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 RIP: 0033:0x457ec9 Code: 6d b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 3b b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007f8750c06c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002f RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000457ec9 RDX: 0000000000002000 RSI: 0000000020000400 RDI: 0000000000000005 RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f8750c076d4 R13: 00000000004c4a60 R14: 00000000004d8140 R15: 00000000ffffffff Uninit was stored to memory at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:204 [inline] kmsan_save_stack mm/kmsan/kmsan.c:219 [inline] kmsan_internal_chain_origin+0x134/0x230 mm/kmsan/kmsan.c:439 __msan_chain_origin+0x70/0xe0 mm/kmsan/kmsan_instr.c:200 ipv6_recv_error+0x1e3f/0x1eb0 net/ipv6/datagram.c:475 udpv6_recvmsg+0x398/0x2ab0 net/ipv6/udp.c:335 inet_recvmsg+0x4fb/0x600 net/ipv4/af_inet.c:830 sock_recvmsg_nosec net/socket.c:794 [inline] sock_recvmsg+0x1d1/0x230 net/socket.c:801 ___sys_recvmsg+0x4d5/0x1140 net/socket.c:2278 __sys_recvmsg net/socket.c:2327 [inline] __do_sys_recvmsg net/socket.c:2337 [inline] __se_sys_recvmsg+0x2fa/0x450 net/socket.c:2334 __x64_sys_recvmsg+0x4a/0x70 net/socket.c:2334 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:204 [inline] kmsan_internal_poison_shadow+0x92/0x150 mm/kmsan/kmsan.c:158 kmsan_kmalloc+0xa6/0x130 mm/kmsan/kmsan_hooks.c:176 kmsan_slab_alloc+0xe/0x10 mm/kmsan/kmsan_hooks.c:185 slab_post_alloc_hook mm/slab.h:446 [inline] slab_alloc_node mm/slub.c:2759 [inline] __kmalloc_node_track_caller+0xe18/0x1030 mm/slub.c:4383 __kmalloc_reserve net/core/skbuff.c:137 [inline] __alloc_skb+0x309/0xa20 net/core/skbuff.c:205 alloc_skb include/linux/skbuff.h:998 [inline] ipv6_local_error+0x1a7/0x9e0 net/ipv6/datagram.c:334 __ip6_append_data+0x129f/0x4fd0 net/ipv6/ip6_output.c:1311 ip6_make_skb+0x6cc/0xcf0 net/ipv6/ip6_output.c:1775 udpv6_sendmsg+0x3f8e/0x45d0 net/ipv6/udp.c:1384 inet_sendmsg+0x54a/0x720 net/ipv4/af_inet.c:798 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg net/socket.c:631 [inline] __sys_sendto+0x8c4/0xac0 net/socket.c:1788 __do_sys_sendto net/socket.c:1800 [inline] __se_sys_sendto+0x107/0x130 net/socket.c:1796 __x64_sys_sendto+0x6e/0x90 net/socket.c:1796 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 Bytes 4-7 of 28 are uninitialized Memory access of size 28 starts at ffff8881937bfce0 Data copied to user address 0000000020000000 Signed-off-by:
-
Mark Rutland authored
[ Backport of upstream commit b3669b1e ] To allow EL0 (and/or EL1) to use pointer authentication functionality, we must ensure that pointer authentication instructions and accesses to pointer authentication keys are not trapped to EL2. This patch ensures that HCR_EL2 is configured appropriately when the kernel is booted at EL2. For non-VHE kernels we set HCR_EL2.{API,APK}, ensuring that EL1 can access keys and permit EL0 use of instructions. For VHE kernels host EL0 (TGE && E2H) is unaffected by these settings, and it doesn't matter how we configure HCR_EL2.{API,APK}, so we don't bother setting them. This does not enable support for KVM guests, since KVM manages HCR_EL2 itself when running VMs. Reviewed-by:
Richard Henderson <richard.henderson@linaro.org> Signed-off-by:
Mark Rutland <mark.rutland@arm.com> Acked-by:
Christoffer Dall <christoffer.dall@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: kvmarm@lists.cs.columbia.edu Signed-off-by:
Will Deacon <will.deacon@arm.com> [kristina: backport to 4.4.y: adjust context] Signed-off-by:
Kristina Martsenko <kristina.martsenko@arm.com> Signed-off-by:
-
