- 27 Jan, 2020 40 commits
-
-
Navid Emamdoost authored
[ Upstream commit 450c3d41 ] In affs_remount if data is provided it is duplicated into new_opts. The allocated memory for new_opts is only released if parse_options fails. There's a bit of history behind new_options, originally there was save/replace options on the VFS layer so the 'data' passed must not change (thus strdup), this got cleaned up in later patches. But not completely. There's no reason to do the strdup in cases where the filesystem does not need to reuse the 'data' again, because strsep would modify it directly. Fixes: c8f33d0b ("affs: kstrdup() memory handling") Signed-off-by:
Navid Emamdoost <navid.emamdoost@gmail.com> [ update changelog ] Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
H. Nikolaus Schaller authored
[ Upstream commit 16568b4a ] wl1251 and wl1271 have different vendor id and device id. So we need to handle both with sdio quirks. Fixes: 884f3860 ("mmc: core: move some sdio IDs out of quirks file") Signed-off-by:
H. Nikolaus Schaller <hns@goldelico.com> Cc: <stable@vger.kernel.org> # v4.11+ Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
H. Nikolaus Schaller authored
[ Upstream commit e5db673e ] v4.11-rc1 did introduce a patch series that rearranged the sdio quirks into a header file. Unfortunately this did forget to handle SDIO_VENDOR_ID_TI differently between wl1251 and wl1271 with the result that although the wl1251 was found on the sdio bus, the firmware did not load any more and there was no interface registration. This patch defines separate constants to be used by sdio quirks and drivers. Fixes: 884f3860 ("mmc: core: move some sdio IDs out of quirks file") Signed-off-by:
-
Alain Volmat authored
[ Upstream commit d77eceb2 ] Distinguish between the case where dma information is not provided within the DT and the case of an error during the dma init. Exit the probe with error in case of an error during dma init. Fixes: bb8822cb ("i2c: i2c-stm32: Add generic DMA API") Signed-off-by:
Alain Volmat <alain.volmat@st.com> Reviewed-by:
Pierre-Yves MORDRET <pierre-yves.mordret@st.com> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit b756ad92 ] KCSAN reported the following data-race [1] Adding a couple of READ_ONCE()/WRITE_ONCE() should silence it. Since the report hinted about multiple cpus using the history concurrently, I added a test avoiding writing on it if the victim slot already contains the desired value. [1] BUG: KCSAN: data-race in fanout_demux_rollover / fanout_demux_rollover read to 0xffff8880b01786cc of 4 bytes by task 18921 on cpu 1: fanout_flow_is_huge net/packet/af_packet.c:1303 [inline] fanout_demux_rollover+0x33e/0x3f0 net/packet/af_packet.c:1353 packet_rcv_fanout+0x34e/0x490 net/packet/af_packet.c:1453 deliver_skb net/core/dev.c:1888 [inline] dev_queue_xmit_nit+0x15b/0x540 net/core/dev.c:1958 xmit_one net/core/dev.c:3195 [inline] dev_hard_start_xmit+0x3f5/0x430 net/core/dev.c:3215 __dev_queue_xmit+0x14ab/0x1b40 net/core/dev.c:3792 dev_queue_xmit+0x21/0x30 net/core/dev.c:3825 neigh_direct_output+0x1f/0x30 net/core/neighbour.c:1530 neigh_output include/net/neighbour.h:511 [inline] ip6_finish_output2+0x7a2/0xec0 net/ipv6/ip6_output.c:116 __ip6_finish_output net/ipv6/ip6_output.c:142 [inline] __ip6_finish_output+0x2d7/0x330 net/ipv6/ip6_output.c:127 ip6_finish_output+0x41/0x160 net/ipv6/ip6_output.c:152 NF_HOOK_COND include/linux/netfilter.h:294 [inline] ip6_output+0xf2/0x280 net/ipv6/ip6_output.c:175 dst_output include/net/dst.h:436 [inline] ip6_local_out+0x74/0x90 net/ipv6/output_core.c:179 ip6_send_skb+0x53/0x110 net/ipv6/ip6_output.c:1795 udp_v6_send_skb.isra.0+0x3ec/0xa70 net/ipv6/udp.c:1173 udpv6_sendmsg+0x1906/0x1c20 net/ipv6/udp.c:1471 inet6_sendmsg+0x6d/0x90 net/ipv6/af_inet6.c:576 sock_sendmsg_nosec net/socket.c:637 [inline] sock_sendmsg+0x9f/0xc0 net/socket.c:657 ___sys_sendmsg+0x2b7/0x5d0 net/socket.c:2311 __sys_sendmmsg+0x123/0x350 net/socket.c:2413 __do_sys_sendmmsg net/socket.c:2442 [inline] __se_sys_sendmmsg net/socket.c:2439 [inline] __x64_sys_sendmmsg+0x64/0x80 net/socket.c:2439 do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x44/0xa9 write to 0xffff8880b01786cc of 4 bytes by task 18922 on cpu 0: fanout_flow_is_huge net/packet/af_packet.c:1306 [inline] fanout_demux_rollover+0x3a4/0x3f0 net/packet/af_packet.c:1353 packet_rcv_fanout+0x34e/0x490 net/packet/af_packet.c:1453 deliver_skb net/core/dev.c:1888 [inline] dev_queue_xmit_nit+0x15b/0x540 net/core/dev.c:1958 xmit_one net/core/dev.c:3195 [inline] dev_hard_start_xmit+0x3f5/0x430 net/core/dev.c:3215 __dev_queue_xmit+0x14ab/0x1b40 net/core/dev.c:3792 dev_queue_xmit+0x21/0x30 net/core/dev.c:3825 neigh_direct_output+0x1f/0x30 net/core/neighbour.c:1530 neigh_output include/net/neighbour.h:511 [inline] ip6_finish_output2+0x7a2/0xec0 net/ipv6/ip6_output.c:116 __ip6_finish_output net/ipv6/ip6_output.c:142 [inline] __ip6_finish_output+0x2d7/0x330 net/ipv6/ip6_output.c:127 ip6_finish_output+0x41/0x160 net/ipv6/ip6_output.c:152 NF_HOOK_COND include/linux/netfilter.h:294 [inline] ip6_output+0xf2/0x280 net/ipv6/ip6_output.c:175 dst_output include/net/dst.h:436 [inline] ip6_local_out+0x74/0x90 net/ipv6/output_core.c:179 ip6_send_skb+0x53/0x110 net/ipv6/ip6_output.c:1795 udp_v6_send_skb.isra.0+0x3ec/0xa70 net/ipv6/udp.c:1173 udpv6_sendmsg+0x1906/0x1c20 net/ipv6/udp.c:1471 inet6_sendmsg+0x6d/0x90 net/ipv6/af_inet6.c:576 sock_sendmsg_nosec net/socket.c:637 [inline] sock_sendmsg+0x9f/0xc0 net/socket.c:657 ___sys_sendmsg+0x2b7/0x5d0 net/socket.c:2311 __sys_sendmmsg+0x123/0x350 net/socket.c:2413 __do_sys_sendmmsg net/socket.c:2442 [inline] __se_sys_sendmmsg net/socket.c:2439 [inline] __x64_sys_sendmmsg+0x64/0x80 net/socket.c:2439 do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Reported by Kernel Concurrency Sanitizer on: CPU: 0 PID: 18922 Comm: syz-executor.3 Not tainted 5.4.0-rc6+ #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Fixes: 3b3a5b0a ("packet: rollover huge flows before small flows") Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 9d027e3a ] A difference of two unsigned long needs long storage. Fixes: c7fb64db ("[NETLINK]: Neighbour table configuration and statistics via rtnetlink") Signed-off-by:
-
Stephen Hemminger authored
[ Upstream commit df9f540c ] When the driver needs to create a hash value because it was not done at higher level, then the hash should be marked as a software not hardware hash. Fixes: f72860af ("hv_netvsc: Exclude non-TCP port numbers from vRSS hashing") Signed-off-by:
Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by:
-
Tiezhu Yang authored
[ Upstream commit dece3c2a ] When call function hwmon_device_register failed, use the actual return value instead of always -ENOMEM. Fixes: 64f09aa9 ("MIPS: Loongson-3: Add CPU Hwmon platform driver") Signed-off-by:
Tiezhu Yang <yangtiezhu@loongson.cn> Signed-off-by:
Paul Burton <paulburton@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: Huacai Chen <chenhc@lemote.com> Cc: Jiaxun Yang <jiaxun.yang@flygoat.com> Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
-
Madalin Bucur authored
[ Upstream commit 9a4f4f3a ] The dpaa_cleanup_tx_fd() function is called by the frame transmit confirmation callback but also on several error paths. This function is reading the transmit timestamp value. Avoid reading an invalid timestamp value on the error paths. Fixes: 4664856e ("dpaa_eth: add support for hardware timestamping") Signed-off-by:
Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by:
-
Madalin Bucur authored
[ Upstream commit c70fd318 ] DMA unmapping is required before accessing the HW provided timestamping information. Fixes: 4664856e ("dpaa_eth: add support for hardware timestamping") Signed-off-by:
-
Tony Lindgren authored
[ Upstream commit 0c0ef9ea ] Commit 0ed266d7 ("clk: ti: omap3: cleanup unnecessary clock aliases") removed old omap3 clock framework aliases but caused omap3-rom-rng to stop working with clock not found error. Based on discussions on the mailing list it was requested by Tero Kristo that it would be best to fix this issue by probing omap3-rom-rng using device tree to provide a proper clk property. The other option would be to add back the missing clock alias, but that does not help moving things forward with removing old legacy platform_data. Let's also add a proper device tree binding and keep it together with the fix. Cc: devicetree@vger.kernel.org Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Adam Ford <aford173@gmail.com> Cc: Pali Rohár <pali.rohar@gmail.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Sebastian Reichel <sre@kernel.org> Cc: Tero Kristo <t-kristo@ti.com> Fixes: 0ed266d7 ("clk: ti: omap3: cleanup unnecessary clock aliases") Reported-by:
Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by:
Tony Lindgren <tony@atomide.com> Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit fb2ee9bf ] The "lvds->backlight" pointer could be NULL in situations where of_parse_phandle() returns NULL. This code is cleaner if we use the managed devm_of_find_backlight() so the clean up is automatic. Fixes: 7c9dff5b ("drm: panels: Add LVDS panel driver") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190911104928.GA15930@mwandaSigned-off-by:
-
Marc Dionne authored
[ Upstream commit b485275f ] By default s_maxbytes is set to MAX_NON_LFS, which limits the usable file size to 2GB, enforced by the vfs. Commit b9b1f8d5 ("AFS: write support fixes") added support for the 64-bit fetch and store server operations, but did not change this value. As a result, attempts to write past the 2G mark result in EFBIG errors: $ dd if=/dev/zero of=foo bs=1M count=1 seek=2048 dd: error writing 'foo': File too large Set s_maxbytes to MAX_LFS_FILESIZE. Fixes: b9b1f8d5 ("AFS: write support fixes") Signed-off-by:
Marc Dionne <marc.dionne@auristor.com> Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Haiyang Zhang authored
[ Upstream commit 171c1fd9 ] If negotiated NVSP version <= NVSP_PROTOCOL_VERSION_6, the offset may be wrong (too small) due to a host bug. This can cause missing the end of the send indirection table, and add multiple zero entries from leading zeros before the data region. This bug adds extra burden on channel 0. So fix the offset by computing it from the data structure sizes. This will ensure netvsc driver runs normally on unfixed hosts, and future fixed hosts. Fixes: 5b54dac8 ("hyperv: Add support for virtual Receive Side Scaling (vRSS)") Signed-off-by:
Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by:
-
Haiyang Zhang authored
[ Upstream commit 71f21959 ] To reach the data region, the existing code adds offset in struct nvsp_5_send_indirect_table on the beginning of this struct. But the offset should be based on the beginning of its container, struct nvsp_message. This bug causes the first table entry missing, and adds an extra zero from the zero pad after the data region. This can put extra burden on the channel 0. So, correct the offset usage. Also add a boundary check to ensure not reading beyond data region. Fixes: 5b54dac8 ("hyperv: Add support for virtual Receive Side Scaling (vRSS)") Signed-off-by:
-
Stefan Wahren authored
[ Upstream commit bc19c329 ] The reset counter is specific for every QCA700x chip. So move this into the private driver struct. Otherwise we get unpredictable reset behavior in setups with multiple QCA700x chips. Fixes: 291ab06e (net: qualcomm: new Ethernet over SPI driver for QCA7000) Signed-off-by:
Stefan Wahren <stefan.wahren@in-tech.com> Signed-off-by:
Stefan Wahren <wahrenst@gmx.net> Signed-off-by:
-
David Howells authored
[ Upstream commit c74386d5 ] In afs_wait_for_call_to_complete(), rather than immediately aborting an operation if a signal occurs, the code attempts to wait for it to complete, using a schedule timeout of 2*RTT (or min 2 jiffies) and a check that we're still receiving relevant packets from the server before we consider aborting the call. We may even ping the server to check on the status of the call. However, there's a missing timeout reset in the event that we do actually get a packet to process, such that if we then get a couple of short stalls, we then time out when progress is actually being made. Fix this by resetting the timeout any time we get something to process. If it's the failure of the call then the call state will get changed and we'll exit the loop shortly thereafter. A symptom of this is data fetches and stores failing with EINTR when they really shouldn't. Fixes: bc5e3a54 ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals") Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit d0fbb51d ] We need to drop the bpf_devs_lock on error before returning. Fixes: 9fd7c555 ("bpf: offload: aggregate offloads per-device") Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Link: https://lore.kernel.org/bpf/20191104091536.GB31509@mwandaSigned-off-by:
-
Magnus Karlsson authored
[ Upstream commit 2afd23f7 ] Having Rx-only AF_XDP sockets can potentially lead to a crash in the system by a NULL pointer dereference in xsk_umem_consume_tx(). This function iterates through a list of all sockets tied to a umem and checks if there are any packets to send on the Tx ring. Rx-only sockets do not have a Tx ring, so this will cause a NULL pointer dereference. This will happen if you have registered one or more Rx-only sockets to a umem and the driver is checking the Tx ring even on Rx, or if the XDP_SHARED_UMEM mode is used and there is a mix of Rx-only and other sockets tied to the same umem. Fixed by only putting sockets with a Tx component on the list that xsk_umem_consume_tx() iterates over. Fixes: ac98d8aa ("xsk: wire upp Tx zero-copy functions") Reported-by:
Kal Cutter Conley <kal.conley@dectris.com> Signed-off-by:
Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by:
Alexei Starovoitov <ast@kernel.org> Acked-by:
Jonathan Lemon <jonathan.lemon@gmail.com> Link: https://lore.kernel.org/bpf/1571645818-16244-1-git-send-email-magnus.karlsson@intel.comSigned-off-by:
-
Jakub Kicinski authored
[ Upstream commit e0ad032e ] If packet corruption failed we jump to finish_segs and return NET_XMIT_SUCCESS. Seeing success will make the parent qdisc increment its backlog, that's incorrect - we need to return NET_XMIT_DROP. Fixes: 6071bd1a ("netem: Segment GSO packets on enqueue") Signed-off-by:
Simon Horman <simon.horman@netronome.com> Signed-off-by:
-
Jakub Kicinski authored
[ Upstream commit a7fa12d1 ] To corrupt a GSO frame we first perform segmentation. We then proceed using the first segment instead of the full GSO skb and requeue the rest of the segments as separate packets. If there are any issues with processing the first segment we still want to process the rest, therefore we jump to the finish_segs label. Commit 177b8007 ("net: netem: fix backlog accounting for corrupted GSO frames") started using the pointer to the first segment in the "rest of segments processing", but as mentioned above the first segment may had already been freed at this point. Backlog corrections for parent qdiscs have to be adjusted. Fixes: 177b8007 ("net: netem: fix backlog accounting for corrupted GSO frames") Reported-by:
kbuild test robot <lkp@intel.com> Reported-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Pavel Tatashin authored
[ Upstream commit 8c551f91 ] There is a bug in create_safe_exec_page(), when page table is allocated it is not checked that table is allocated successfully: But it is dereferenced in: pgd_none(READ_ONCE(*pgdp)). Check that allocation was successful. Fixes: 82869ac5 ("arm64: kernel: Add support for hibernate/suspend-to-disk") Reviewed-by:
James Morse <james.morse@arm.com> Signed-off-by:
Pavel Tatashin <pasha.tatashin@soleen.com> Signed-off-by:
Will Deacon <will@kernel.org> Signed-off-by:
-
Jean Delvare authored
[ Upstream commit 81dde26d ] Before reading the Extended Size field, we should ensure it fits in the DMI record. There is already a record length check but it does not cover that field. It would take a seriously corrupted DMI table to hit that bug, so no need to worry, but we should still fix it. Signed-off-by:
Jean Delvare <jdelvare@suse.de> Fixes: 6deae96b ("firmware, DMI: Add function to look up a handle and return DIMM size") Cc: Tony Luck <tony.luck@intel.com> Cc: Borislav Petkov <bp@suse.de> Signed-off-by:
-
Robin Gong authored
[ Upstream commit bd73dfab ] Illegal memory will be touch if SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V3 (41) exceed the size of structure sdma_script_start_addrs(40), thus cause memory corrupt such as slob block header so that kernel trap into while() loop forever in slob_free(). Please refer to below code piece in imx-sdma.c: for (i = 0; i < sdma->script_number; i++) if (addr_arr[i] > 0) saddr_arr[i] = addr_arr[i]; /* memory corrupt here */ That issue was brought by commit a572460b ("dmaengine: imx-sdma: Add support for version 3 firmware") because SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V3 (38->41 3 scripts added) not align with script number added in sdma_script_start_addrs(2 scripts). Fixes: a572460b ("dmaengine: imx-sdma: Add support for version 3 firmware") Cc: stable@vger.kernel Link: https://www.spinics.net/lists/arm-kernel/msg754895.htmlSigned-off-by:
Robin Gong <yibin.gong@nxp.com> Reported-by:
Jurgen Lambrecht <J.Lambrecht@TELEVIC.com> Link: https://lore.kernel.org/r/1569347584-3478-1-git-send-email-yibin.gong@nxp.com [vkoul: update the patch title] Signed-off-by:
Vinod Koul <vkoul@kernel.org> Signed-off-by:
-
Michael S. Tsirkin authored
[ Upstream commit 245cdd9f ] When device stop was moved out of reset, test device wasn't updated to stop before reset, this resulted in a use after free. Fix by invoking stop appropriately. Fixes: b211616d ("vhost: move -net specific code out") Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Jeffrey Hugo authored
[ Upstream commit 78e31c42 ] On msm8998, vblank timeouts are observed because the DSI controller is not reset properly, which ends up stalling the MDP. This is because the reset logic is not correct per the hardware documentation. The documentation states that after asserting reset, software should wait some time (no indication of how long), or poll the status register until it returns 0 before deasserting reset. wmb() is insufficient for this purpose since it just ensures ordering, not timing between writes. Since asserting and deasserting reset occurs on the same register, ordering is already guaranteed by the architecture, making the wmb extraneous. Since we would define a timeout for polling the status register to avoid a possible infinite loop, lets just use a static delay of 20 ms, since 16.666 ms is the time available to process one frame at 60 fps. Fixes: a689554b ("drm/msm: Initial add DSI connector support") Cc: Hai Li <hali@codeaurora.org> Cc: Rob Clark <robdclark@gmail.com> Signed-off-by:
Jeffrey Hugo <jeffrey.l.hugo@gmail.com> Reviewed-by:
Sean Paul <sean@poorly.run> [seanpaul renamed RESET_DELAY to DSI_RESET_TOGGLE_DELAY_MS] Signed-off-by:
Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191011133939.16551-1-jeffrey.l.hugo@gmail.comSigned-off-by:
-
Karsten Graul authored
[ Upstream commit 107529e3 ] smc_rx_recvmsg() first checks if data is available, and then if RCV_SHUTDOWN is set. There is a race when smc_cdc_msg_recv_action() runs in between these 2 checks, receives data and sets RCV_SHUTDOWN. In that case smc_rx_recvmsg() would return from receive without to process the available data. Fix that with a final check for data available if RCV_SHUTDOWN is set. Move the check for data into a function and call it twice. And use the existing helper smc_rx_data_available(). Fixes: 952310cc ("smc: receive data from RMBE") Reviewed-by:
Ursula Braun <ubraun@linux.ibm.com> Signed-off-by:
Karsten Graul <kgraul@linux.ibm.com> Signed-off-by:
-
Karsten Graul authored
[ Upstream commit 882dcfe5 ] smc_cdc_rxed_any_close_or_senddone() is used as an end condition for the receive loop. This conflicts with smc_cdc_msg_recv_action() which could run in parallel and set the bits checked by smc_cdc_rxed_any_close_or_senddone() before the receive is processed. In that case we could return from receive with no data, although data is available. The same applies to smc_rx_wait(). Fix this by checking for RCV_SHUTDOWN only, which is set in smc_cdc_msg_recv_action() after the receive was actually processed. Fixes: 952310cc ("smc: receive data from RMBE") Reviewed-by:
-
Eric Dumazet authored
[ Upstream commit 1f142c17 ] tcp_memory_pressure is read without holding any lock, and its value could be changed on other cpus. Use READ_ONCE() to annotate these lockless reads. The write side is already using atomic ops. Fixes: b8da51eb ("tcp: introduce tcp_under_memory_pressure()") Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 60b173ca ] reqsk_queue_empty() is called from inet_csk_listen_poll() while other cpus might write ->rskq_accept_head value. Use {READ|WRITE}_ONCE() to avoid compiler tricks and potential KCSAN splats. Fixes: fff1f300 ("tcp: add a spinlock to protect struct request_sock_queue") Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 503978ac ] As mentioned in https://github.com/google/ktsan/wiki/READ_ONCE-and-WRITE_ONCE#it-may-improve-performance a C compiler can legally transform : if (memory_pressure && *memory_pressure) *memory_pressure = 0; to : if (memory_pressure) *memory_pressure = 0; Fixes: 06044751 ("tcp: add TCPMemoryPressuresChrono counter") Fixes: 180d8cd9 ("foundations of per-cgroup memory pressure controlling.") Fixes: 3ab224be ("[NET] CORE: Introducing new memory accounting interface.") Signed-off-by:
-
YueHaibing authored
[ Upstream commit 11c9a7d3 ] If tcf_register_action failed, mirred_device_notifier should be unregistered. Fixes: 3b87956e ("net sched: fix race in mirred device removal") Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
Alexandra Winter authored
[ Upstream commit be40a86c ] Without this patch, a command bit in the supported commands mask is only ever set to unsupported during set online. If a command is ever marked as unsupported (e.g. because of error during qeth_l2_vnicc_query_cmds), subsequent successful initialization (offline/online) would not bring it back. Fixes: caa1f0b1 ("s390/qeth: add VNICC enable/disable support") Signed-off-by:
Alexandra Winter <wintera@linux.ibm.com> Signed-off-by:
Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by:
-
Alexandra Winter authored
[ Upstream commit b528965b ] Smatch discovered the use of uninitialized variable sup_cmds in error paths. Fixes: caa1f0b1 ("s390/qeth: add VNICC enable/disable support") Signed-off-by:
-
Xin Long authored
[ Upstream commit 819be810 ] This patch is to fix a NULL-ptr deref in selinux_socket_connect_helper: [...] kasan: GPF could be caused by NULL-ptr deref or user memory access [...] RIP: 0010:selinux_socket_connect_helper+0x94/0x460 [...] Call Trace: [...] selinux_sctp_bind_connect+0x16a/0x1d0 [...] security_sctp_bind_connect+0x58/0x90 [...] sctp_process_asconf+0xa52/0xfd0 [sctp] [...] sctp_sf_do_asconf+0x785/0x980 [sctp] [...] sctp_do_sm+0x175/0x5a0 [sctp] [...] sctp_assoc_bh_rcv+0x285/0x5b0 [sctp] [...] sctp_backlog_rcv+0x482/0x910 [sctp] [...] __release_sock+0x11e/0x310 [...] release_sock+0x4f/0x180 [...] sctp_accept+0x3f9/0x5a0 [sctp] [...] inet_accept+0xe7/0x720 It was caused by that the 'newsk' sk_socket was not set before going to security sctp hook when processing asconf chunk with SCTP_PARAM_ADD_IP or SCTP_PARAM_SET_PRIMARY: inet_accept()-> sctp_accept(): lock_sock(): lock listening 'sk' do_softirq(): sctp_rcv(): <-- [1] asconf chunk arrives and enqueued in 'sk' backlog sctp_sock_migrate(): set asoc's sk to 'newsk' release_sock(): sctp_backlog_rcv(): lock 'newsk' sctp_process_asconf() <-- [2] unlock 'newsk' sock_graft(): set sk_socket <-- [3] As it shows, at [1] the asconf chunk would be put into the listening 'sk' backlog, as accept() was holding its sock lock. Then at [2] asconf would get processed with 'newsk' as asoc's sk had been set to 'newsk'. However, 'newsk' sk_socket is not set until [3], while selinux_sctp_bind_connect() would deref it, then kernel crashed. Here to fix it by adding the chunk to sk_backlog until newsk sk_socket is set when .accept() is done. Note that sk->sk_socket can be NULL when the sock is closed, so SOCK_DEAD flag is also needed to check in sctp_newsk_ready(). Thanks to Ondrej for reviewing the code. Fixes: d452930f ("selinux: Add SCTP support") Reported-by:
Ying Xu <yinxu@redhat.com> Suggested-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Antonio Borneo authored
[ Upstream commit 520cf600 ] Accordingly to Synopsys documentation [1] and [2], when bit PPSEN0 in register MAC_PPS_CONTROL is set it selects the functionality command in the same register, otherwise selects the functionality control. Command functionality is required to either enable (command 0x2) and disable (command 0x5) the flexible PPS output, but the bit PPSEN0 is currently set only for enabling. Set the bit PPSEN0 to properly disable flexible PPS output. Tested on STM32MP15x, based on dwmac 4.10a. [1] DWC Ethernet QoS Databook 4.10a October 2014 [2] DWC Ethernet QoS Databook 5.00a September 2017 Signed-off-by:
Antonio Borneo <antonio.borneo@st.com> Fixes: 9a8a02c9 ("net: stmmac: Add Flexible PPS support") Signed-off-by:
-
Antonio Borneo authored
[ Upstream commit 5da202c8 ] The field "name" in struct ptp_clock_info has a fixed size of 16 chars and is used as zero terminated string by clock_name_show() in drivers/ptp/ptp_sysfs.c The current initialization value requires 17 chars to fit also the null termination, and this causes overflow to the next bytes in the struct when the string is read as null terminated: hexdump -C /sys/class/ptp/ptp0/clock_name 00000000 73 74 6d 6d 61 63 5f 70 74 70 5f 63 6c 6f 63 6b |stmmac_ptp_clock| 00000010 a0 ac b9 03 0a |.....| where the extra 4 bytes (excluding the newline) after the string represent the integer 0x03b9aca0 = 62500000 assigned to the field "max_adj" that follows "name" in the same struct. There is no strict requirement for the "name" content and in the comment in ptp_clock_kernel.h it's reported it should just be 'A short "friendly name" to identify the clock'. Replace it with "stmmac ptp". Signed-off-by:
-
Haishuang Yan authored
[ Upstream commit 4123f637 ] ip6erspan driver calls ether_setup(), after commit 61e84623 ("net: centralize net_device min/max MTU checking"), the range of mtu is [min_mtu, max_mtu], which is [68, 1500] by default. It causes the dev mtu of the erspan device to not be greater than 1500, this limit value is not correct for ip6erspan tap device. Fixes: 61e84623 ("net: centralize net_device min/max MTU checking") Signed-off-by:
Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Acked-by:
William Tu <u9012063@gmail.com> Signed-off-by:
-
Eric Biggers authored
[ Upstream commit 36453c85 ] If llc_conn_state_process() sees that llc_conn_service() put the skb on a list, it will drop one fewer references to it. This is wrong because the current behavior is that llc_conn_service() never consumes a reference to the skb. The code also makes the number of skb references being dropped conditional on which of ind_prim and cfm_prim are nonzero, yet neither of these affects how many references are *acquired*. So there is extra code that tries to fix this up by sometimes taking another reference. Remove the unnecessary/broken refcounting logic and instead just add an skb_get() before the only two places where an extra reference is actually consumed. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
-
Eric Biggers authored
[ Upstream commit fc8d5db1 ] All callers of llc_conn_state_process() except llc_build_and_send_pkt() (via llc_ui_sendmsg() -> llc_ui_send_data()) assume that it always consumes a reference to the skb. Fix this caller to do the same. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
