This patch adds a USB GPIO based reset for dwc3-xilinx driver. The PHY
needs to be reset after the completion of phy initialization. As part
of the reset, check for gpio-reset binding before toggling the pin.
This feature is advantageous when the user toggle GPIO to trigger the
ULPI-PHY reset.

Delay of milliseconds is added in between low and high to meet the setup
and hold time requirement of the reset. The reset-gpio error handling is
added for error notification.

Some GPIO controllers must be accessed using message-based buses, like
I2C or SPI, to address this problem, updates GPIO access with sleep API.

This reset is specific to the zynqMp.
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Link: https://lore.kernel.org/r/20220504075309.6244-3-piyush.mehta@xilinx.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Added optional property support reset-gpios for the dwc3-Xilinx
glue driver.
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220504075309.6244-2-piyush.mehta@xilinx.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add devicetree binding for SDX65 USB controller based on
Qcom designware IP.
Signed-off-by: Rohit Agarwal <quic_rohiagar@quicinc.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/1651482395-29443-3-git-send-email-quic_rohiagar@quicinc.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The generic property, used in most of the drivers and defined in generic
dma-common DT bindings, is 'dma-channels'.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220503065201.51818-3-krzysztof.kozlowski@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The generic property, used in most of the drivers and defined in generic
dma-common DT bindings, is 'dma-channels'.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20220503065201.51818-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch removes a possible unnecessary out of memory message from
core.c as reported by checkpatch.pl:
   WARNING: Possible unnecessary 'out of memory' message
Signed-off-by: Kushagra Verma <kushagra765@outlook.com>
Link: https://lore.kernel.org/r/SI2PR01MB392926A7AFB821410770D7CFF8C19@SI2PR01MB3929.apcprd01.prod.exchangelabs.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It is no longer needed. The sysdev pointer is now used when
assigning the ACPI companions to the xHCI ports and USB
devices.

Assigning the ACPI companion here resulted in the
fwnode->secondary pointer to be replaced also for the parent
dwc3 device since the primary fwnode (the ACPI companion)
was shared. That was unintentional and it created potential
side effects like resource leaks.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220428111056.3558-3-heikki.krogerus@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The controller device (hcd) does not always have the ACPI
companion assigned to it at all. We can not rely on it when
finding the ACPI companion for the root hub. Instead we need
to use the sysdev pointer.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220428111056.3558-2-heikki.krogerus@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add binding to support the mtu3 driver on the MT8195 SoC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Link: https://lore.kernel.org/r/20220426134106.242353-2-fparent@baylibre.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

After moving the omap1 platform into generalized multiplatform
support on ARM, the kernel test robot points out a W=1 warning that
now shows up in more configurations:

drivers/usb/host/ehci-omap.c:64:19: warning: unused function 'ehci_read'

The function was last used 9 years ago and can just be removed.

Fixes: 87425ad3 ("USB: ehci-omap: Remove PHY reset handling code")
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20220428102314.950323-1-arnd@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently when driver->match_existing_only is true, the error return is
set to -EBUSY however ret is then set to 0 at the end of the if/else
statement. I believe the ret = 0 statement should be set in the else
part of the if statement and not at the end to ensure -EBUSY is being
returned correctly.

Detected by clang scan:
drivers/usb/gadget/udc/core.c:1558:4: warning: Value stored to 'ret' is
never read [deadcode.DeadStores]

Fixes: fc274c1e ("USB: gadget: Add a new bus for gadgets")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220504135840.232209-1-colin.i.king@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

UDC driver should not touch gadget's driver internals, especially it
should not reset driver->bus. This wasn't harmful so far, but since
commit fc274c1e ("USB: gadget: Add a new bus for gadgets") gadget
subsystem got it's own bus and messing with ->bus triggers the
following NULL pointer dereference:

dwc2 12480000.hsotg: bound driver g_ether
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in: ...
CPU: 0 PID: 620 Comm: modprobe Not tainted 5.18.0-rc5-next-20220504 #11862
Hardware name: Samsung Exynos (Flattened Device Tree)
PC is at module_add_driver+0x44/0xe8
LR is at sysfs_do_create_link_sd+0x84/0xe0
...
Process modprobe (pid: 620, stack limit = 0x(ptrval))
...
 module_add_driver from bus_add_driver+0xf4/0x1e4
 bus_add_driver from driver_register+0x78/0x10c
 driver_register from usb_gadget_register_driver_owner+0x40/0xb4
 usb_gadget_register_driver_owner from do_one_initcall+0x44/0x1e0
 do_one_initcall from do_init_module+0x44/0x1c8
 do_init_module from load_module+0x19b8/0x1b9c
 load_module from sys_finit_module+0xdc/0xfc
 sys_finit_module from ret_fast_syscall+0x0/0x54
Exception stack(0xf1771fa8 to 0xf1771ff0)
...
dwc2 12480000.hsotg: new device is high-speed
---[ end trace 0000000000000000 ]---

Fix this by removing driver->bus entry reset.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20220505104618.22729-1-m.szyprowski@samsung.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 8e8b1195.

The series still has built errors as reported in linux-next, so revert
it for now.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20220502210728.0b36f3cd@canb.auug.org.au
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 0298b4b9.

The series still has built errors as reported in linux-next, so revert
it for now.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20220502210728.0b36f3cd@canb.auug.org.au
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit c40b6221.

The series still has built errors as reported in linux-next, so revert
it for now.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20220502210728.0b36f3cd@canb.auug.org.au
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We need the USB fixes in here, and this resolves a merge issue in
drivers/usb/dwc3/drd.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull kvm fixes from Paolo Bonzini:
 "ARM:

   - Take care of faults occuring between the PARange and IPA range by
     injecting an exception

   - Fix S2 faults taken from a host EL0 in protected mode

   - Work around Oops caused by a PMU access from a 32bit guest when PMU
     has been created. This is a temporary bodge until we fix it for
     good.

  x86:

   - Fix potential races when walking host page table

   - Fix shadow page table leak when KVM runs nested

   - Work around bug in userspace when KVM synthesizes leaf 0x80000021
     on older (pre-EPYC) or Intel processors

  Generic (but affects only RISC-V):

   - Fix bad user ABI for KVM_EXIT_SYSTEM_EVENT"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: work around QEMU issue with synthetic CPUID leaves
  Revert "x86/mm: Introduce lookup_address_in_mm()"
  KVM: x86/mmu: fix potential races when walking host page table
  KVM: fix bad user ABI for KVM_EXIT_SYSTEM_EVENT
  KVM: x86/mmu: Do not create SPTEs for GFNs that exceed host.MAXPHYADDR
  KVM: arm64: Inject exception on out-of-IPA-range translation fault
  KVM/arm64: Don't emulate a PMU for 32-bit guests if feature not set
  KVM: arm64: Handle host stage-2 faults from 32-bit EL0

Pull x86 fixes from Borislav Petkov:

 - A fix to disable PCI/MSI[-X] masking for XEN_HVM guests as that is
   solely controlled by the hypervisor

 - A build fix to make the function prototype (__warn()) as visible as
   the definition itself

 - A bunch of objtool annotation fixes which have accumulated over time

 - An ORC unwinder fix to handle bad input gracefully

 - Well, we thought the microcode gets loaded in time in order to
   restore the microcode-emulated MSRs but we thought wrong. So there's
   a fix for that to have the ordering done properly

 - Add new Intel model numbers

 - A spelling fix

* tag 'x86_urgent_for_v5.18_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/pci/xen: Disable PCI/MSI[-X] masking for XEN_HVM guests
  bug: Have __warn() prototype defined unconditionally
  x86/Kconfig: fix the spelling of 'becoming' in X86_KERNEL_IBT config
  objtool: Use offstr() to print address of missing ENDBR
  objtool: Print data address for "!ENDBR" data warnings
  x86/xen: Add ANNOTATE_NOENDBR to startup_xen()
  x86/uaccess: Add ENDBR to __put_user_nocheck*()
  x86/retpoline: Add ANNOTATE_NOENDBR for retpolines
  x86/static_call: Add ANNOTATE_NOENDBR to static call trampoline
  objtool: Enable unreachable warnings for CLANG LTO
  x86,objtool: Explicitly mark idtentry_body()s tail REACHABLE
  x86,objtool: Mark cpu_startup_entry() __noreturn
  x86,xen,objtool: Add UNWIND hint
  lib/strn*,objtool: Enforce user_access_begin() rules
  MAINTAINERS: Add x86 unwinding entry
  x86/unwind/orc: Recheck address range after stack info was updated
  x86/cpu: Load microcode during restore_processor_state()
  x86/cpu: Add new Alderlake and Raptorlake CPU model numbers

Pull objtool fixes from Borislav Petkov:
 "A bunch of objtool fixes to improve unwinding, sibling call detection,
  fallthrough detection and relocation handling of weak symbols when the
  toolchain strips section symbols"

* tag 'objtool_urgent_for_v5.18_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Fix code relocs vs weak symbols
  objtool: Fix type of reloc::addend
  objtool: Fix function fallthrough detection for vmlinux
  objtool: Fix sibling call detection in alternatives
  objtool: Don't set 'jump_dest' for sibling calls
  x86/uaccess: Don't jump between functions

Pull irq fix from Borislav Petkov:

 - Fix locking when accessing device MSI descriptors

* tag 'irq_urgent_for_v5.18_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  bus: fsl-mc-msi: Fix MSI descriptor mutex lock for msi_first_desc()

Merge tag 'driver-core-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core fixes from Greg KH:
 "Here are some small driver core and kernfs fixes for some reported
  problems. They include:

   - kernfs regression that is causing oopses in 5.17 and newer releases

   - topology sysfs fixes for a few small reported problems.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'driver-core-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  kernfs: fix NULL dereferencing in kernfs_remove
  topology: Fix up build warning in topology_is_visible()
  arch_topology: Do not set llc_sibling if llc_id is invalid
  topology: make core_mask include at least cluster_siblings
  topology/sysfs: Hide PPIN on systems that do not support it.

Pull char/misc driver fixes from Greg KH:
 "Here are a small number of char/misc/other driver fixes for 5.18-rc5

  Nothing major in here, this is mostly IIO driver fixes along with some
  other small things:

   - at25 driver fix for systems without a dma-able stack

   - phy driver fixes for reported issues

   - binder driver fixes for reported issues

  All of these have been in linux-next without any reported problems"

* tag 'char-misc-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (31 commits)
  eeprom: at25: Use DMA safe buffers
  binder: Gracefully handle BINDER_TYPE_FDA objects with num_fds=0
  binder: Address corner cases in deferred copy and fixup
  phy: amlogic: fix error path in phy_g12a_usb3_pcie_probe()
  iio: imu: inv_icm42600: Fix I2C init possible nack
  iio: dac: ltc2688: fix voltage scale read
  interconnect: qcom: sdx55: Drop IP0 interconnects
  interconnect: qcom: sc7180: Drop IP0 interconnects
  phy: ti: Add missing pm_runtime_disable() in serdes_am654_probe
  phy: mapphone-mdm6600: Fix PM error handling in phy_mdm6600_probe
  phy: ti: omap-usb2: Fix error handling in omap_usb2_enable_clocks
  bus: mhi: host: pci_generic: Flush recovery worker during freeze
  bus: mhi: host: pci_generic: Add missing poweroff() PM callback
  phy: ti: tusb1210: Fix an error handling path in tusb1210_probe()
  phy: samsung: exynos5250-sata: fix missing device put in probe error paths
  phy: samsung: Fix missing of_node_put() in exynos_sata_phy_probe
  phy: ti: Fix missing of_node_put in ti_pipe3_get_sysctrl()
  phy: ti: tusb1210: Make tusb1210_chg_det_states static
  iio:dac:ad3552r: Fix an IS_ERR() vs NULL check
  iio: sx9324: Fix default precharge internal resistance register
  ...

Pull tty/serial fixes from Greg KH:
 "Here are some small serial driver fixes, and a larger number of GSM
  line discipline fixes for 5.18-rc5.

  These include:

   - lots of tiny n_gsm fixes for issues to resolve a number of reported
     problems. Seems that people are starting to actually use this code
     again.

   - 8250 driver fixes for some devices

   - imx serial driver fix

   - amba-pl011 driver fix

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'tty-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (27 commits)
  tty: n_gsm: fix sometimes uninitialized warning in gsm_dlci_modem_output()
  serial: 8250: Correct the clock for EndRun PTP/1588 PCIe device
  serial: 8250: Also set sticky MCR bits in console restoration
  tty: n_gsm: fix software flow control handling
  tty: n_gsm: fix invalid use of MSC in advanced option
  tty: n_gsm: fix broken virtual tty handling
  Revert "serial: sc16is7xx: Clear RS485 bits in the shutdown"
  tty: n_gsm: fix missing update of modem controls after DLCI open
  serial: 8250: Fix runtime PM for start_tx() for empty buffer
  serial: imx: fix overrun interrupts in DMA mode
  serial: amba-pl011: do not time out prematurely when draining tx fifo
  tty: n_gsm: fix incorrect UA handling
  tty: n_gsm: fix reset fifo race condition
  tty: n_gsm: fix missing tty wakeup in convergence layer type 2
  tty: n_gsm: fix wrong signal octets encoding in MSC
  tty: n_gsm: fix wrong command frame length field encoding
  tty: n_gsm: fix wrong command retry handling
  tty: n_gsm: fix missing explicit ldisc flush
  tty: n_gsm: fix wrong DLCI release order
  tty: n_gsm: fix insufficient txframe size
  ...

Pull USB fixes from Greg KH:
 "Here are a number of small USB driver fixes for 5.18-rc5 for some
  reported issues and new quirks. They include:

   - dwc3 driver fixes

   - xhci driver fixes

   - typec driver fixes

   - new usb-serial driver ids

   - added new USB devices to existing quirk tables

   - other tiny fixes

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (31 commits)
  usb: phy: generic: Get the vbus supply
  usb: dwc3: gadget: Return proper request status
  usb: dwc3: pci: add support for the Intel Meteor Lake-P
  usb: dwc3: core: Only handle soft-reset in DCTL
  usb: gadget: configfs: clear deactivation flag in configfs_composite_unbind()
  usb: misc: eud: Fix an error handling path in eud_probe()
  usb: core: Don't hold the device lock while sleeping in do_proc_control()
  usb: dwc3: Try usb-role-switch first in dwc3_drd_init
  usb: dwc3: core: Fix tx/rx threshold settings
  usb: mtu3: fix USB 3.0 dual-role-switch from device to host
  xhci: Enable runtime PM on second Alderlake controller
  usb: dwc3: fix backwards compat with rockchip devices
  dt-bindings: usb: samsung,exynos-usb2: add missing required reg
  usb: misc: fix improper handling of refcount in uss720_probe()
  USB: Fix ehci infinite suspend-resume loop issue in zhaoxin
  usb: typec: tcpm: Fix undefined behavior due to shift overflowing the constant
  usb: typec: rt1719: Fix build error without CONFIG_POWER_SUPPLY
  usb: typec: ucsi: Fix role swapping
  usb: typec: ucsi: Fix reuse of completion structure
  usb: xhci: tegra:Fix PM usage reference leak of tegra_xusb_unpowergate_partitions
  ...

Pull SCSI fix from James Bottomley:
 "One fix for an endless error loop with the target driver affecting
  tapes"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: target: pscsi: Set SCF_TREAT_READ_AS_NORMAL flag only if there is valid data

Pull ARM SoC fixes from Arnd Bergmann:

 - A fix for a regression caused by the previous set of bugfixes
   changing tegra and at91 pinctrl properties.

   More work is needed to figure out what this should actually be, but a
   revert makes it work for the moment.

 - Defconfig regression fixes for tegra after renamed symbols

 - Build-time warning and static checker fixes for imx, op-tee, sunxi,
   meson, at91, and omap

 - More at91 DT fixes for audio, regulator and spi nodes

 - A regression fix for Renesas Hyperflash memory probe

 - A stability fix for amlogic boards, modifying the allowed cpufreq
   states

 - Multiple fixes for system suspend on omap2+

 - DT fixes for various i.MX bugs

 - A probe error fix for imx6ull-colibri MMC

 - A MAINTAINERS file entry for samsung bug reports

* tag 'soc-fixes-5.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
  Revert "arm: dts: at91: Fix boolean properties with values"
  bus: sunxi-rsb: Fix the return value of sunxi_rsb_device_create()
  Revert "arm64: dts: tegra: Fix boolean properties with values"
  arm64: dts: imx8mn-ddr4-evk: Describe the 32.768 kHz PMIC clock
  ARM: dts: imx6ull-colibri: fix vqmmc regulator
  MAINTAINERS: add Bug entry for Samsung and memory controller drivers
  memory: renesas-rpc-if: Fix HF/OSPI data transfer in Manual Mode
  ARM: dts: logicpd-som-lv: Fix wrong pinmuxing on OMAP35
  ARM: dts: am3517-evm: Fix misc pinmuxing
  ARM: dts: am33xx-l4: Add missing touchscreen clock properties
  ARM: dts: Fix mmc order for omap3-gta04
  ARM: dts: at91: fix pinctrl phandles
  ARM: dts: at91: sama5d4_xplained: fix pinctrl phandle name
  ARM: dts: at91: Describe regulators on at91sam9g20ek
  ARM: dts: at91: Map MCLK for wm8731 on at91sam9g20ek
  ARM: dts: at91: Fix boolean properties with values
  ARM: dts: at91: use generic node name for dataflash
  ARM: dts: at91: align SPI NOR node name with dtschema
  ARM: dts: at91: sama7g5ek: Align the impedance of the QSPI0's HSIO and PCB lines
  ARM: dts: at91: sama7g5ek: enable pull-up on flexcom3 console lines
  ...

Pull clk fixes from Stephen Boyd:
 "A semi-large pile of clk driver fixes this time around.

  Nothing is touching the core so these fixes are fairly well contained
  to specific devices that use these clk drivers.

   - Some Allwinner SoC fixes to gracefully handle errors and mark an
     RTC clk as critical so that the RTC keeps ticking.

   - Fix AXI bus clks and RTC clk design for Microchip PolarFire SoC
     driver introduced this cycle. This has some devicetree bits acked
     by riscv maintainers. We're fixing it now so that the prior
     bindings aren't released in a major kernel version.

   - Remove a reset on Microchip PolarFire SoCs that broke when enabling
     CONFIG_PM.

   - Set a min/max for the Qualcomm graphics clk. This got broken by the
     clk rate range patches introduced this cycle"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: sunxi: sun9i-mmc: check return value after calling platform_get_resource()
  clk: sunxi-ng: sun6i-rtc: Mark rtc-32k as critical
  riscv: dts: microchip: reparent mpfs clocks
  clk: microchip: mpfs: add RTCREF clock control
  clk: microchip: mpfs: re-parent the configurable clocks
  dt-bindings: rtc: add refclk to mpfs-rtc
  dt-bindings: clk: mpfs: add defines for two new clocks
  dt-bindings: clk: mpfs document msspll dri registers
  riscv: dts: microchip: fix usage of fic clocks on mpfs
  clk: microchip: mpfs: mark CLK_ATHENA as critical
  clk: microchip: mpfs: fix parents for FIC clocks
  clk: qcom: clk-rcg2: fix gfx3d frequency calculation
  clk: microchip: mpfs: don't reset disabled peripherals
  clk: sunxi-ng: fix not NULL terminated coccicheck error

Pull block fixes from Jens Axboe:

 - Revert of a patch that caused timestamp issues (Tejun)

 - iocost warning fix (Tejun)

 - bfq warning fix (Jan)

* tag 'block-5.18-2022-04-29' of git://git.kernel.dk/linux-block:
  bfq: Fix warning in bfqq_request_over_limit()
  Revert "block: inherit request start time from bio for BLK_CGROUP"
  iocost: don't reset the inuse weight of under-weighted debtors

Pull io_uring fixes from Jens Axboe:
 "Pretty boring:

   - three patches just adding reserved field checks (me, Eugene)

   - Fixing a potential regression with IOPOLL caused by a block change
     (Joseph)"

Boring is good.

* tag 'io_uring-5.18-2022-04-29' of git://git.kernel.dk/linux-block:
  io_uring: check that data field is 0 in ringfd unregister
  io_uring: fix uninitialized field in rw io_kiocb
  io_uring: check reserved fields for recv/recvmsg
  io_uring: check reserved fields for send/sendmsg

Pull random number generator fixes from Jason Donenfeld:

 - Eric noticed that the memmove() in crng_fast_key_erasure() was bogus,
   so this has been changed to a memcpy() and the confusing situation
   clarified with a detailed comment.

 - [Half]SipHash documentation updates from Bagas and Eric, after Eric
   pointed out that the use of HalfSipHash in random.c made a bit of the
   text potentially misleading.

* tag 'random-5.18-rc5-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
  Documentation: siphash: disambiguate HalfSipHash algorithm from hsiphash functions
  Documentation: siphash: enclose HalfSipHash usage example in the literal block
  Documentation: siphash: convert danger note to warning for HalfSipHash
  random: document crng_fast_key_erasure() destination possibility

Pull ceph client fixes from Ilya Dryomov:
 "A fix for a NULL dereference that turns out to be easily triggerable
  by fsync (marked for stable) and a false positive WARN and snap_rwsem
  locking fixups"

* tag 'ceph-for-5.18-rc5' of https://github.com/ceph/ceph-client:
  ceph: fix possible NULL pointer dereference for req->r_session
  ceph: remove incorrect session state check
  ceph: get snap_rwsem read lock in handle_cap_export for ceph_add_cap
  libceph: disambiguate cluster/pool full log message

This reverts commit 0dc23d1a, which caused another regression
as the pinctrl code actually expects an integer value of 0 or 1
rather than a simple boolean property.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Synthesizing AMD leaves up to 0x80000021 caused problems with QEMU,
which assumes the *host* CPUID[0x80000000].EAX is higher or equal
to what KVM_GET_SUPPORTED_CPUID reports.

This causes QEMU to issue bogus host CPUIDs when preparing the input
to KVM_SET_CPUID2.  It can even get into an infinite loop, which is
only terminated by an abort():

   cpuid_data is full, no space for cpuid(eax:0x8000001d,ecx:0x3e)

To work around this, only synthesize those leaves if 0x8000001d exists
on the host.  The synthetic 0x80000021 leaf is mostly useful on Zen2,
which satisfies the condition.

Fixes: f144c49e ("KVM: x86: synthesize CPUID leaf 0x80000021h if useful")
Reported-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Merge tag 'perf-tools-fixes-for-v5.18-2022-04-29' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux

Pull perf tools fixes from Arnaldo Carvalho de Melo:

 - Fix Intel PT (Processor Trace) timeless decoding with perf.data
   directory.

 - ARM SPE (Statistical Profiling Extensions) address fixes, for
   synthesized events and for SPE events with physical addresses. Add a
   simple 'perf test' entry to make sure this doesn't regress.

 - Remove arch specific processing of kallsyms data to fixup symbol end
   address, fixing excessive memory consumption in the annotation code.

* tag 'perf-tools-fixes-for-v5.18-2022-04-29' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
  perf symbol: Remove arch__symbols__fixup_end()
  perf symbol: Update symbols__fixup_end()
  perf symbol: Pass is_kallsyms to symbols__fixup_end()
  perf test: Add perf_event_attr test for Arm SPE
  perf arm-spe: Fix SPE events with phys addresses
  perf arm-spe: Fix addresses of synthesized SPE events
  perf intel-pt: Fix timeless decoding with perf.data directory

Pull RISC-V fixes from Palmer Dabbelt:

 - A fix to properly ensure a single CPU is running during patch_text().

 - A defconfig update to include RPMSG_CTRL when RPMSG_CHAR was set,
   necessary after a recent refactoring.

* tag 'riscv-for-linus-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  RISC-V: configs: Configs that had RPMSG_CHAR now get RPMSG_CTRL
  riscv: patch_text: Fixup last cpu should be master

Pull arm64 fix from Will Deacon:
 "Rename and reallocate the PT_ARM_MEMTAG_MTE ELF segment type.

  This is a fix to the MTE ELF ABI for a bug that was added during the
  most recent merge window as part of the coredump support.

  The issue is that the value assigned to the new PT_ARM_MEMTAG_MTE
  segment type has already been allocated to PT_AARCH64_UNWIND by the
  ELF ABI, so we've bumped the value and changed the name of the
  identifier to be better aligned with the existing one"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  elf: Fix the arm64 MTE ELF segment name and value

Drop lookup_address_in_mm() now that KVM is providing it's own variant
of lookup_address_in_pgd() that is safe for use with user addresses, e.g.
guards against page tables being torn down.  A variant that provides a
non-init mm is inherently dangerous and flawed, as the only reason to use
an mm other than init_mm is to walk a userspace mapping, and
lookup_address_in_pgd() does not play nice with userspace mappings, e.g.
doesn't disable IRQs to block TLB shootdowns and doesn't use READ_ONCE()
to ensure an upper level entry isn't converted to a huge page between
checking the PAGE_SIZE bit and grabbing the address of the next level
down.

This reverts commit 13c72c06.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <YmwIi3bXr/1yhYV/@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Fixes for (relatively) old bugs, to be merged in both the -rc and next
development trees:

* Fix potential races when walking host page table

* Fix bad user ABI for KVM_EXIT_SYSTEM_EVENT

* Fix shadow page table leak when KVM runs nested

KVM uses lookup_address_in_mm() to detect the hugepage size that the host
uses to map a pfn.  The function suffers from several issues:

 - no usage of READ_ONCE(*). This allows multiple dereference of the same
   page table entry. The TOCTOU problem because of that may cause KVM to
   incorrectly treat a newly generated leaf entry as a nonleaf one, and
   dereference the content by using its pfn value.

 - the information returned does not match what KVM needs; for non-present
   entries it returns the level at which the walk was terminated, as long
   as the entry is not 'none'.  KVM needs level information of only 'present'
   entries, otherwise it may regard a non-present PXE entry as a present
   large page mapping.

 - the function is not safe for mappings that can be torn down, because it
   does not disable IRQs and because it returns a PTE pointer which is never
   safe to dereference after the function returns.

So implement the logic for walking host page tables directly in KVM, and
stop using lookup_address_in_mm().

Cc: Sean Christopherson <seanjc@google.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Mingwei Zhang <mizhang@google.com>
Message-Id: <20220429031757.2042406-1-mizhang@google.com>
[Inline in host_pfn_mapping_level, ensure no semantic change for its
 callers. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>