Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ERROR: code indent should use tabs where possible: fix 2.
ERROR: do not use assignment in if condition: fix 5.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Just follow the Joe Perches's opinion, it is a better way to fix the
style errors.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool core will lower the requested length to the one returned by
get_regs_len, therefore no additional check is needed in the get_regs
function.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch generates a hardware crash notification (NETDEV_REBOOT)
during reset. After a hardware crash, ENIC resets all its resources
including queue pair filters programmed by USNIC. USNIC registers for
this notification, and on receiving it, reprograms the queue pair
filters.
Signed-off-by: Neel Patel <neepatel@cisco.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds an interface for USNIC to proxy firmware commands
through ENIC.
Signed-off-by: Neel Patel <neepatel@cisco.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch,
    - Adds new firmware commands for the new Cisco Low Latency NIC
      (aka. USNIC).
Signed-off-by: Neel Patel <neepatel@cisco.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	net/netfilter/nf_conntrack_proto_tcp.c

The conflict had to do with overlapping changes dealing with
fixing the use of an "s32" to hold the value returned by
NAT_OFFSET().

Pablo Neira Ayuso says:

====================
The following batch contains Netfilter/IPVS updates for your net-next tree.
More specifically, they are:

* Trivial typo fix in xt_addrtype, from Phil Oester.

* Remove net_ratelimit in the conntrack logging for consistency with other
  logging subsystem, from Patrick McHardy.

* Remove unneeded includes from the recently added xt_connlabel support, from
  Florian Westphal.

* Allow to update conntracks via nfqueue, don't need NFQA_CFG_F_CONNTRACK for
  this, from Florian Westphal.

* Remove tproxy core, now that we have socket early demux, from Florian
  Westphal.

* A couple of patches to refactor conntrack event reporting to save a good
  bunch of lines, from Florian Westphal.

* Fix missing locking in NAT sequence adjustment, it did not manifested in
  any known bug so far, from Patrick McHardy.

* Change sequence number adjustment variable to 32 bits, to delay the
  possible early overflow in long standing connections, also from Patrick.

* Comestic cleanups for IPVS, from Dragos Foianu.

* Fix possible null dereference in IPVS in the SH scheduler, from Daniel
  Borkmann.

* Allow to attach conntrack expectations via nfqueue. Before this patch, you
  had to use ctnetlink instead, thus, we save the conntrack lookup.

* Export xt_rpfilter and xt_HMARK header files, from Nicolas Dichtel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexander Aring says:

====================
6lowpan: address uncompression fixes

The current implementation to uncompress addresses in a 6lowpan header
is completely broken.

This patch series fixes the parsing of addresses in a 6lowpan header.
It contains a major rewrite of the uncompress address function to parse
the address in a correct way.

Tested with the ravenusbstick(contiki 6LoWPAN stack) and beaglebone
(linux 6LoWPAN Stack) on the other side. The linux side contains all
possible addresses for the uncompression cases. Then I type a ping6 for
each case and lookup in wireshark and dmesg the correct reconstruction.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Handle context based address when an unspecified address is given.
For other context based address we print a warning and drop the packet
because we don't support it right now.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch drops the pre and postcount calculation from the
lowpan_uncompress_addr function.We use instead a switch/case
over address_mode value. The original implementation has several
bugs in this function and it was hard to decrypt how it works.
To make it maintainable and fix these bugs this patch basically
reimplements lowpan_uncompress_addr from scratch.

A list of bugs we found in the current implementation:

1) Properly support uncompression of short-address based IPv6 addresses
   (instead of basically copying garbage)

2) Fix use and uncompression of long-addresses based IPv6 addresses

3) Add missing ff:fe00 in the case of SAM/DAM = 2 and M = 0
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add function to uncompress multicast address.
This function split the uncompress function for a multicast address
in a seperate function.

To uncompress a multicast address is different than a other
non-multicasts addresses according to rfc6282.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a helper function to parse the ipv6 header to a
6lowpan header in stream.

This function checks first if we can pull data with a specific
length from a skb. If this seems to be okay, we copy skb data to
a destination pointer and run skb_pull.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a new 6lowpan fragment is received, a skbuff is allocated for
the reassembled packet. However when a 6lowpan packet compresses
link-local addresses based on link-layer addresses, the processing
function relies on the skb mac control block to find the related
link-layer address.

This patch copies the control block from the first fragment into
the newly allocated skb to keep a trace of the link-layer addresses
in case of a link-local compressed address.

Edit: small changes on comment issue
Signed-off-by: David Hauweele <david@hauweele.net>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch simplify the handling to set fields inside of struct ipv6hdr
to zero. Instead of setting some memory regions with memset to zero we
initialize the whole ipv6hdr to zero.

This is a simplification for parsing the 6lowpan header for the upcomming
patches.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Use appropriate firmware image file name based on device IDs.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Loopback initiator function drivers should process loopback time extend AEN.
  These AENs are triggered by the loopback time extend mailbox command
  issued by the target function drivers.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o 84xx adapters support VLAN stripping for PVID. Packets don't have
  VLAN tag inserted in case of PVID. So packet should follow non vlan path.

o Use capability bit to set PVID mode.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pravin B Shelar says:

====================
openvswitch: VXLAN tunneling.

First four vxlan patches extends vxlan so that openvswitch
can share vxlan recv code. Rest of patches refactors vxlan
data plane so that ovs can share that code with vxlan module.
Last patch adds vxlan-vport to openvswitch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Following patch adds vxlan vport type for openvswitch using
vxlan api. So now there is vxlan dependency for openvswitch.

CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Following patch allows transmit side vlan offload for vxlan
devices.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rather than having static headroom calculation, adjust headroom
according to target device.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Following patch allows more code sharing between vxlan and ovs-vxlan.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Following patch adds data field to vxlan socket and export
vxlan handler api.
vh->data is required to store private data per vxlan handler.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Once we have ovs-vxlan functionality, one UDP port can be assigned
to kernel-vxlan or ovs-vxlan port.  Therefore following patch adds
vxlan demux functionality, so that vxlan or ovs module can
register for particular port.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use iptunnel_pull_header() for better code sharing.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Restructure vxlan-socket management APIs so that it can be
shared between vxlan and ovs modules.
This patch does not change any functionality.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
v6-v7:
 - get rid of zero refcnt vs from hashtable.
Signed-off-by: David S. Miller <davem@davemloft.net>

Add comments.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Split some parts of code into another function to simplify
tx_bottom(). Use while loop to replace the goto loop.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move some declearation of variables in rx_bottom().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- Use r8152_get_tx_agg for getting tx agg list
- Replace submit rx with goto submit
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace lockflags with flags.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the type of contex of tx_agg and rx_agg from void * to
staruc r8152 *.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove memset(tp, 0, sizeof(*tp));
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull clock controller fixes from Michael Turquette:
 "Two small fixes for the Zynq clock controller introduced in 3.11-rc1
  and another Exynos clock patch which fixes a regression that prevents
  the video pipeline from functioning on that platform"

* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
  clk: exynos4: Add CLK_GET_RATE_NOCACHE flag for the Exynos4x12 ISP clocks
  clk/zynq/clkc: Add CLK_SET_RATE_PARENT flag to ethernet muxes
  clk/zynq/clkc: Add dedicated spinlock for the SWDT