- 29 Oct, 2019 31 commits
-
-
Cédric Le Goater authored
[ Upstream commit 11d49ce9 ] pSeries machines on POWER9 processors can run with the XICS (legacy) interrupt mode or with the XIVE exploitation interrupt mode. These interrupt contollers have different interfaces for interrupt management : XICS uses hcalls and XIVE loads and stores on a page. H_EOI being a XICS interface the enable_scrq_irq() routine can fail when the machine runs in XIVE mode. Fix that by calling the EOI handler of the interrupt chip. Fixes: f23e0643 ("ibmvnic: Clear pending interrupt after device reset") Signed-off-by:
Cédric Le Goater <clg@kaod.org> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Thomas Bogendoerfer authored
[ Upstream commit 61c1d33d ] Commit 7f683b92 ("i825xx: switch to switch to dma_alloc_attrs") switched dma allocation over to dma_alloc_attr, but didn't convert the SNI part to request consistent DMA memory. This broke sni_82596 since driver doesn't do dma_cache_sync for performance reasons. Fix this by using different DMA_ATTRs for lasi_82596 and sni_82596. Fixes: 7f683b92 ("i825xx: switch to switch to dma_alloc_attrs") Signed-off-by:
Thomas Bogendoerfer <tbogendoerfer@suse.de> Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit 92696286 ] phydev->dev_flags is entirely dependent on the PHY device driver which is going to be used, setting the internal GENET PHY revision in those bits only makes sense when drivers/net/phy/bcm7xxx.c is the PHY driver being used. Fixes: 487320c5 ("net: bcmgenet: communicate integrated PHY revision to PHY driver") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Acked-by:
Doug Berger <opendmb@gmail.com> Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit efb86fed ] The RGMII_MODE_EN bit value was 0 for GENET versions 1 through 3, and became 6 for GENET v4 and above, account for that difference. Fixes: aa09677c ("net: bcmgenet: add MDIO routines") Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 39f13ea2 ] tc_ctl_action() has the ability to loop forever if tcf_action_add() returns -EAGAIN. This special case has been done in case a module needed to be loaded, but it turns out that tcf_add_notify() could also return -EAGAIN if the socket sk_rcvbuf limit is hit. We need to separate the two cases, and only loop for the module loading case. While we are at it, add a limit of 10 attempts since unbounded loops are always scary. syzbot repro was something like : socket(PF_NETLINK, SOCK_RAW|SOCK_NONBLOCK, NETLINK_ROUTE) = 3 write(3, ..., 38) = 38 setsockopt(3, SOL_SOCKET, SO_RCVBUF, [0], 4) = 0 sendmsg(3, {msg_name(0)=NULL, msg_iov(1)=[{..., 388}], msg_controllen=0, msg_flags=0x10}, ...) NMI backtrace for cpu 0 CPU: 0 PID: 1054 Comm: khungtaskd Not tainted 5.4.0-rc1+ #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x172/0x1f0 lib/dump_stack.c:113 nmi_cpu_backtrace.cold+0x70/0xb2 lib/nmi_backtrace.c:101 nmi_trigger_cpumask_backtrace+0x23b/0x28b lib/nmi_backtrace.c:62 arch_trigger_cpumask_backtrace+0x14/0x20 arch/x86/kernel/apic/hw_nmi.c:38 trigger_all_cpu_backtrace include/linux/nmi.h:146 [inline] check_hung_uninterruptible_tasks kernel/hung_task.c:205 [inline] watchdog+0x9d0/0xef0 kernel/hung_task.c:289 kthread+0x361/0x430 kernel/kthread.c:255 ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352 Sending NMI from CPU 0 to CPUs 1: NMI backtrace for cpu 1 CPU: 1 PID: 8859 Comm: syz-executor910 Not tainted 5.4.0-rc1+ #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:arch_local_save_flags arch/x86/include/asm/paravirt.h:751 [inline] RIP: 0010:lockdep_hardirqs_off+0x1df/0x2e0 kernel/locking/lockdep.c:3453 Code: 5c 08 00 00 5b 41 5c 41 5d 5d c3 48 c7 c0 58 1d f3 88 48 ba 00 00 00 00 00 fc ff df 48 c1 e8 03 80 3c 10 00 0f 85 d3 00 00 00 <48> 83 3d 21 9e 99 07 00 0f 84 b9 00 00 00 9c 58 0f 1f 44 00 00 f6 RSP: 0018:ffff8880a6f3f1b8 EFLAGS: 00000046 RAX: 1ffffffff11e63ab RBX: ffff88808c9c6080 RCX: 0000000000000000 RDX: dffffc0000000000 RSI: 0000000000000000 RDI: ffff88808c9c6914 RBP: ffff8880a6f3f1d0 R08: ffff88808c9c6080 R09: fffffbfff16be5d1 R10: fffffbfff16be5d0 R11: 0000000000000003 R12: ffffffff8746591f R13: ffff88808c9c6080 R14: ffffffff8746591f R15: 0000000000000003 FS: 00000000011e4880(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffff600400 CR3: 00000000a8920000 CR4: 00000000001406e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: trace_hardirqs_off+0x62/0x240 kernel/trace/trace_preemptirq.c:45 __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:108 [inline] _raw_spin_lock_irqsave+0x6f/0xcd kernel/locking/spinlock.c:159 __wake_up_common_lock+0xc8/0x150 kernel/sched/wait.c:122 __wake_up+0xe/0x10 kernel/sched/wait.c:142 netlink_unlock_table net/netlink/af_netlink.c:466 [inline] netlink_unlock_table net/netlink/af_netlink.c:463 [inline] netlink_broadcast_filtered+0x705/0xb80 net/netlink/af_netlink.c:1514 netlink_broadcast+0x3a/0x50 net/netlink/af_netlink.c:1534 rtnetlink_send+0xdd/0x110 net/core/rtnetlink.c:714 tcf_add_notify net/sched/act_api.c:1343 [inline] tcf_action_add+0x243/0x370 net/sched/act_api.c:1362 tc_ctl_action+0x3b5/0x4bc net/sched/act_api.c:1410 rtnetlink_rcv_msg+0x463/0xb00 net/core/rtnetlink.c:5386 netlink_rcv_skb+0x177/0x450 net/netlink/af_netlink.c:2477 rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5404 netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline] netlink_unicast+0x531/0x710 net/netlink/af_netlink.c:1328 netlink_sendmsg+0x8a5/0xd60 net/netlink/af_netlink.c:1917 sock_sendmsg_nosec net/socket.c:637 [inline] sock_sendmsg+0xd7/0x130 net/socket.c:657 ___sys_sendmsg+0x803/0x920 net/socket.c:2311 __sys_sendmsg+0x105/0x1d0 net/socket.c:2356 __do_sys_sendmsg net/socket.c:2365 [inline] __se_sys_sendmsg net/socket.c:2363 [inline] __x64_sys_sendmsg+0x78/0xb0 net/socket.c:2363 do_syscall_64+0xfa/0x760 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x440939 Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by: syzbot+cf0adbb9c28c8866c788@syzkaller.appspotmail.com Signed-off-by:
-
Stefano Brivio authored
[ Upstream commit 595e0651 ] ...instead of -EINVAL. An issue was found with older kernel versions while unplugging a NFS client with pending RPCs, and the wrong error code here prevented it from recovering once link is back up with a configured address. Incidentally, this is not an issue anymore since commit 4f8943f8 ("SUNRPC: Replace direct task wakeups from softirq context"), included in 5.2-rc7, had the effect of decoupling the forwarding of this error by using SO_ERROR in xs_wake_error(), as pointed out by Benjamin Coddington. To the best of my knowledge, this isn't currently causing any further issue, but the error code doesn't look appropriate anyway, and we might hit this in other paths as well. In detail, as analysed by Gonzalo Siero, once the route is deleted because the interface is down, and can't be resolved and we return -EINVAL here, this ends up, courtesy of inet_sk_rebuild_header(), as the socket error seen by tcp_write_err(), called by tcp_retransmit_timer(). In turn, tcp_write_err() indirectly calls xs_error_report(), which wakes up the RPC pending tasks with a status of -EINVAL. This is then seen by call_status() in the SUN RPC implementation, which aborts the RPC call calling rpc_exit(), instead of handling this as a potentially temporary condition, i.e. as a timeout. Return -EINVAL only if the input parameters passed to ip_route_output_key_hash_rcu() are actually invalid (this is the case if the specified source address is multicast, limited broadcast or all zeroes), but return -ENETUNREACH in all cases where, at the given moment, the given source address doesn't allow resolving the route. While at it, drop the initialisation of err to -ENETUNREACH, which was added to __ip_route_output_key() back then by commit 0315e382 ("net: Fix behaviour of unreachable, blackhole and prohibit routes"), but actually had no effect, as it was, and is, overwritten by the fib_lookup() return code assignment, and anyway ignored in all other branches, including the if (fl4->saddr) one: I find this rather confusing, as it would look like -ENETUNREACH is the "default" error, while that statement has no effect. Also note that after commit fc75fc83 ("ipv4: dont create routes on down devices"), we would get -ENETUNREACH if the device is down, but -EINVAL if the source address is specified and we can't resolve the route, and this appears to be rather inconsistent. Reported-by:
Stefan Walter <walteste@inf.ethz.ch> Analysed-by:
Benjamin Coddington <bcodding@redhat.com> Analysed-by:
Gonzalo Siero <gsierohu@redhat.com> Signed-off-by:
Stefano Brivio <sbrivio@redhat.com> Signed-off-by:
-
Wei Wang authored
[ Upstream commit 5018c596 ] Jesse and Ido reported the following race condition: <CPU A, t0> - Received packet A is forwarded and cached dst entry is taken from the nexthop ('nhc->nhc_rth_input'). Calls skb_dst_set() <t1> - Given Jesse has busy routers ("ingesting full BGP routing tables from multiple ISPs"), route is added / deleted and rt_cache_flush() is called <CPU B, t2> - Received packet B tries to use the same cached dst entry from t0, but rt_cache_valid() is no longer true and it is replaced in rt_cache_route() by the newer one. This calls dst_dev_put() on the original dst entry which assigns the blackhole netdev to 'dst->dev' <CPU A, t3> - dst_input(skb) is called on packet A and it is dropped due to 'dst->dev' being the blackhole netdev There are 2 issues in the v4 routing code: 1. A per-netns counter is used to do the validation of the route. That means whenever a route is changed in the netns, users of all routes in the netns needs to redo lookup. v6 has an implementation of only updating fn_sernum for routes that are affected. 2. When rt_cache_valid() returns false, rt_cache_route() is called to throw away the current cache, and create a new one. This seems unnecessary because as long as this route does not change, the route cache does not need to be recreated. To fully solve the above 2 issues, it probably needs quite some code changes and requires careful testing, and does not suite for net branch. So this patch only tries to add the deleted cached rt into the uncached list, so user could still be able to use it to receive packets until it's done. Fixes: 95c47f9c ("ipv4: call dst_dev_put() properly") Signed-off-by:
Wei Wang <weiwan@google.com> Reported-by:
Ido Schimmel <idosch@idosch.org> Reported-by:
Jesse Hathaway <jesse@mbuki-mvuki.org> Tested-by:
Martin KaFai Lau <kafai@fb.com> Cc: David Ahern <dsahern@gmail.com> Reviewed-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
Yi Li authored
commit b918c430 upstream. mount.ocfs2 failed when reading ocfs2 filesystem superblock encounters an error. ocfs2_initialize_super() returns before allocating ocfs2_wq. ocfs2_dismount_volume() triggers the following panic. Oct 15 16:09:27 cnwarekv-205120 kernel: On-disk corruption discovered.Please run fsck.ocfs2 once the filesystem is unmounted. Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_read_locked_inode:537 ERROR: status = -30 Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_init_global_system_inodes:458 ERROR: status = -30 Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_init_global_system_inodes:491 ERROR: status = -30 Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_initialize_super:2313 ERROR: status = -30 Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_fill_super:1033 ERROR: status = -30 ------------[ cut here ]------------ Oops: 0002 [#1] SMP NOPTI CPU: 1 PID: 11753 Comm: mount.ocfs2 Tainted: G E 4.14.148-200.ckv.x86_64 #1 Hardware name: Sugon H320-G30/35N16-US, BIOS 0SSDX017 12/21/2018 task: ffff967af0520000 task.stack: ffffa5f05484000 RIP: 0010:mutex_lock+0x19/0x20 Call Trace: flush_workqueue+0x81/0x460 ocfs2_shutdown_local_alloc+0x47/0x440 [ocfs2] ocfs2_dismount_volume+0x84/0x400 [ocfs2] ocfs2_fill_super+0xa4/0x1270 [ocfs2] ? ocfs2_initialize_super.isa.211+0xf20/0xf20 [ocfs2] mount_bdev+0x17f/0x1c0 mount_fs+0x3a/0x160 Link: http://lkml.kernel.org/r/1571139611-24107-1-git-send-email-yili@winhong.comSigned-off-by:
Yi Li <yilikernel@gmail.com> Reviewed-by:
Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Alex Deucher authored
[ Upstream commit 8d13c187 ] This reverts commit 6f7fe9a9. This breaks some boards. Maybe just enable this on PPC for now? Bug: https://bugzilla.kernel.org/show_bug.cgi?id=205147Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Song Liu authored
[ Upstream commit 3874d73e ] The message should match the parameter, i.e. raid0.default_layout. Fixes: c84a1372 ("md/raid0: avoid RAID0 data corruption due to layout confusion.") Cc: NeilBrown <neilb@suse.de> Reported-by:
Ivan Topolsky <doktor.yak@gmail.com> Signed-off-by:
Song Liu <songliubraving@fb.com> Signed-off-by:
-
Dan Williams authored
[ Upstream commit 09d6ac8d ] Commit c312ef17 "libata/ahci: Drop PCS quirk for Denverton and beyond" got the polarity wrong on the check for which board-ids should have the quirk applied. The board type board_ahci_pcs7 is defined at the end of the list such that "pcs7" boards can be special cased in the future if they need the quirk. All prior Intel board ids "< board_ahci_pcs7" should proceed with applying the quirk. Reported-by:
Andreas Friedrich <afrie@gmx.net> Reported-by:
Stephen Douthit <stephend@silicom-usa.com> Fixes: c312ef17 ("libata/ahci: Drop PCS quirk for Denverton and beyond") Cc: <stable@vger.kernel.org> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Jacob Keller authored
[ Upstream commit 82fdd12b ] The namespace.pl script does not work properly if objtree is not set to an absolute path. The do_nm function is run from within the find function, which changes directories. Because of this, appending objtree, $File::Find::dir, and $source, will return a path which is not valid from the current directory. This used to work when objtree was set to an absolute path when using "make namespacecheck". It appears to have not worked when calling ./scripts/namespace.pl directly. This behavior was changed in 7e1c0477 ("kbuild: Use relative path for $(objtree)", 2014-05-14) Rather than fixing the Makefile to set objtree to an absolute path, just fix namespace.pl to work when srctree and objtree are relative. Also fix the script to use an absolute path for these by default. Use the File::Spec module for this purpose. It's been part of perl 5 since 5.005. The curdir() function is used to get the current directory when the objtree and srctree aren't set in the environment. rel2abs() is used to convert possibly relative objtree and srctree environment variables to absolute paths. Finally, the catfile() function is used instead of string appending paths together, since this is more robust when joining paths together. Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Acked-by:
Randy Dunlap <rdunlap@infradead.org> Tested-by:
Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by:
-
Kai-Heng Feng authored
[ Upstream commit a54cdeeb ] r8152 may fail to establish network connection after resume from system suspend. If the USB port connects to r8152 lost its power during system suspend, the MAC address was written before is lost. The reason is that The MAC address doesn't get written again in its reset_resume callback. So let's set MAC address again in reset_resume callback. Also remove unnecessary lock as no other locking attempt will happen during reset_resume. Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by:
-
Randy Dunlap authored
[ Upstream commit 2105b52e ] This textsearch code example does not need the '\' escapes and they can be misleading to someone reading the example. Also, gcc and sparse warn that the "\%d" is an unknown escape sequence. Fixes: 5968a70d ("textsearch: fix kernel-doc warnings and add kernel-api section") Signed-off-by:
-
Yizhuo authored
[ Upstream commit 53de429f ] In function mdio_sc_cfg_reg_write(), variable "reg_value" could be uninitialized if regmap_read() fails. However, "reg_value" is used to decide the control flow later in the if statement, which is potentially unsafe. Signed-off-by:
Yizhuo <yzhai003@ucr.edu> Signed-off-by:
-
Christophe JAILLET authored
[ Upstream commit 25b69a88 ] 'exit' functions should be marked as __exit, not __init. Fixes: 85cc0288 ("mips: make loongsoon serial driver explicitly modular") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
Paul Burton <paul.burton@mips.com> Cc: chenhc@lemote.com Cc: ralf@linux-mips.org Cc: jhogan@kernel.org Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: kernel-janitors@vger.kernel.org Signed-off-by:
-
Wen Yang authored
[ Upstream commit f32eb9d8 ] of_node_put needs to be called when the device node which is got from of_get_child_by_name finished using. irq_domain_add_linear() also calls of_node_get() to increase refcount, so irq_domain will not be affected when it is released. Fixes: d8652956 ("net: dsa: realtek-smi: Add Realtek SMI driver") Signed-off-by:
Wen Yang <wenyang@linux.alibaba.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Vivien Didelot <vivien.didelot@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Pablo Neira Ayuso authored
[ Upstream commit 34a4c95a ] BH must be disabled when invoking nf_conncount_gc_list() to perform garbage collection, otherwise deadlock might happen. nf_conncount_add+0x1f/0x50 [nf_conncount] nft_connlimit_eval+0x4c/0xe0 [nft_connlimit] nft_dynset_eval+0xb5/0x100 [nf_tables] nft_do_chain+0xea/0x420 [nf_tables] ? sch_direct_xmit+0x111/0x360 ? noqueue_init+0x10/0x10 ? __qdisc_run+0x84/0x510 ? tcp_packet+0x655/0x1610 [nf_conntrack] ? ip_finish_output2+0x1a7/0x430 ? tcp_error+0x130/0x150 [nf_conntrack] ? nf_conntrack_in+0x1fc/0x4c0 [nf_conntrack] nft_do_chain_ipv4+0x66/0x80 [nf_tables] nf_hook_slow+0x44/0xc0 ip_rcv+0xb5/0xd0 ? ip_rcv_finish_core.isra.19+0x360/0x360 __netif_receive_skb_one_core+0x52/0x70 netif_receive_skb_internal+0x34/0xe0 napi_gro_receive+0xba/0xe0 e1000_clean_rx_irq+0x1e9/0x420 [e1000e] e1000e_poll+0xbe/0x290 [e1000e] net_rx_action+0x149/0x3b0 __do_softirq+0xde/0x2d8 irq_exit+0xba/0xc0 do_IRQ+0x85/0xd0 common_interrupt+0xf/0xf </IRQ> RIP: 0010:nf_conncount_gc_list+0x3b/0x130 [nf_conncount] Fixes: 2f971a8f ("netfilter: nf_conncount: move all list iterations under spinlock") Reported-by:
Laura Garcia Liebana <nevola@gmail.com> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Miaoqing Pan authored
[ Upstream commit 8ed31a26 ] If the interface type is P2P_DEVICE or NAN, read the file of '/sys/kernel/debug/ieee80211/phyx/netdev:wlanx/aqm' will get a NULL pointer dereference. As for those interface type, the pointer sdata->vif.txq is NULL. Unable to handle kernel NULL pointer dereference at virtual address 00000011 CPU: 1 PID: 30936 Comm: cat Not tainted 4.14.104 #1 task: ffffffc0337e4880 task.stack: ffffff800cd20000 PC is at ieee80211_if_fmt_aqm+0x34/0xa0 [mac80211] LR is at ieee80211_if_fmt_aqm+0x34/0xa0 [mac80211] [...] Process cat (pid: 30936, stack limit = 0xffffff800cd20000) [...] [<ffffff8000b7cd00>] ieee80211_if_fmt_aqm+0x34/0xa0 [mac80211] [<ffffff8000b7c414>] ieee80211_if_read+0x60/0xbc [mac80211] [<ffffff8000b7ccc4>] ieee80211_if_read_aqm+0x28/0x30 [mac80211] [<ffffff80082eff94>] full_proxy_read+0x2c/0x48 [<ffffff80081eef00>] __vfs_read+0x2c/0xd4 [<ffffff80081ef084>] vfs_read+0x8c/0x108 [<ffffff80081ef494>] SyS_read+0x40/0x7c Signed-off-by:
Miaoqing Pan <miaoqing@codeaurora.org> Acked-by:
Toke Høiland-Jørgensen <toke@redhat.com> Link: https://lore.kernel.org/r/1569549796-8223-1-git-send-email-miaoqing@codeaurora.org [trim useless data from commit message] Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Miaoqing Pan authored
[ Upstream commit b501426c ] If the interface is not in MESH mode, the command 'iw wlanx mpath del' will cause kernel panic. The root cause is null pointer access in mpp_flush_by_proxy(), as the pointer 'sdata->u.mesh.mpp_paths' is NULL for non MESH interface. Unable to handle kernel NULL pointer dereference at virtual address 00000068 [...] PC is at _raw_spin_lock_bh+0x20/0x5c LR is at mesh_path_del+0x1c/0x17c [mac80211] [...] Process iw (pid: 4537, stack limit = 0xd83e0238) [...] [<c021211c>] (_raw_spin_lock_bh) from [<bf8c7648>] (mesh_path_del+0x1c/0x17c [mac80211]) [<bf8c7648>] (mesh_path_del [mac80211]) from [<bf6cdb7c>] (extack_doit+0x20/0x68 [compat]) [<bf6cdb7c>] (extack_doit [compat]) from [<c05c309c>] (genl_rcv_msg+0x274/0x30c) [<c05c309c>] (genl_rcv_msg) from [<c05c25d8>] (netlink_rcv_skb+0x58/0xac) [<c05c25d8>] (netlink_rcv_skb) from [<c05c2e14>] (genl_rcv+0x20/0x34) [<c05c2e14>] (genl_rcv) from [<c05c1f90>] (netlink_unicast+0x11c/0x204) [<c05c1f90>] (netlink_unicast) from [<c05c2420>] (netlink_sendmsg+0x30c/0x370) [<c05c2420>] (netlink_sendmsg) from [<c05886d0>] (sock_sendmsg+0x70/0x84) [<c05886d0>] (sock_sendmsg) from [<c0589f4c>] (___sys_sendmsg.part.3+0x188/0x228) [<c0589f4c>] (___sys_sendmsg.part.3) from [<c058add4>] (__sys_sendmsg+0x4c/0x70) [<c058add4>] (__sys_sendmsg) from [<c0208c80>] (ret_fast_syscall+0x0/0x44) Code: e2822c02 e2822001 e5832004 f590f000 (e1902f9f) ---[ end trace bbd717600f8f884d ]--- Signed-off-by:
-
Ross Lagerwall authored
[ Upstream commit df359f0d ] Other parts of the kernel expect these nonblocking EFI callbacks to exist and crash when running under Xen. Since the implementations of xen_efi_set_variable() and xen_efi_query_variable_info() do not take any locks, use them for the nonblocking callbacks too. Signed-off-by:
Ross Lagerwall <ross.lagerwall@citrix.com> Reviewed-by:
Juergen Gross <jgross@suse.com> Signed-off-by:
-
Oleksij Rempel authored
[ Upstream commit 0889d07f ] It is two registers each of 4 byte. Signed-off-by:
Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by:
-
Michal Vokáč authored
[ Upstream commit 7ae6d93c ] The QCA8K family supports up to 7 ports. So use the existing QCA8K_NUM_PORTS define to allocate the switch structure and limit all operations with the switch ports. This was not an issue until commit 0394a63a ("net: dsa: enable and disable all ports") disabled all unused ports. Since the unused ports 7-11 are outside of the correct register range on this switch some registers were rewritten with invalid content. Fixes: 6b93fb46 ("net-next: dsa: add new driver for qca8xxx family") Fixes: a0c02161 ("net: dsa: variable number of ports") Fixes: 0394a63a ("net: dsa: enable and disable all ports") Signed-off-by:
Michal Vokáč <michal.vokac@ysoft.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Peter Ujfalusi authored
[ Upstream commit f90ec6cd ] Set memory bandwidth limit to filter out resolutions above 720p@60Hz to avoid underflow errors due to the bandwidth needs of higher resolutions. am43xx can not provide enough bandwidth to DISPC to correctly handle 'high' resolutions. Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Navid Emamdoost authored
[ Upstream commit 6402939e ] In ca8210_probe the allocated pdata needs to be assigned to spi_device->dev.platform_data before calling ca8210_get_platform_data. Othrwise when ca8210_get_platform_data fails pdata cannot be released. Signed-off-by:
Navid Emamdoost <navid.emamdoost@gmail.com> Link: https://lore.kernel.org/r/20190917224713.26371-1-navid.emamdoost@gmail.comSigned-off-by:
Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by:
-
Tony Lindgren authored
[ Upstream commit cf395f7d ] This code is currently unable to find the dts opp tables as ti-cpufreq needs to set them up first based on speed binning. We stopped initializing the opp tables with platform code years ago for device tree based booting with commit 92d51856 ("ARM: OMAP3+: do not register non-dt OPP tables for device tree boot"), and all of mach-omap2 is now booting using device tree. We currently get the following errors on init: omap2_set_init_voltage: unable to find boot up OPP for vdd_mpu omap2_set_init_voltage: unable to set vdd_mpu omap2_set_init_voltage: unable to find boot up OPP for vdd_core omap2_set_init_voltage: unable to set vdd_core omap2_set_init_voltage: unable to find boot up OPP for vdd_iva omap2_set_init_voltage: unable to set vdd_iva Let's just drop the unused code. Nowadays ti-cpufreq should be used to to initialize things properly. Cc: Adam Ford <aford173@gmail.com> Cc: André Roth <neolynx@gmail.com> Cc: "H. Nikolaus Schaller" <hns@goldelico.com> Cc: Nishanth Menon <nm@ti.com> Cc: Tero Kristo <t-kristo@ti.com> Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit Signed-off-by:
-
Tony Lindgren authored
[ Upstream commit 8ad8041b ] For ti,sysc-omap4 compatible devices with no sysstatus register, we do have reset done status available in the SOFTRESET bit that clears when the reset is done. This is documented for example in am437x TRM for DMTIMER_TIOCP_CFG register. The am335x TRM just says that SOFTRESET bit value 1 means reset is ongoing, but it behaves the same way clearing after reset is done. With the ti-sysc driver handling this automatically based on no sysstatus register defined, we see warnings if SYSC_HAS_RESET_STATUS is missing in the legacy platform data: ti-sysc 48042000.target-module: sysc_flags 00000222 != 00000022 ti-sysc 48044000.target-module: sysc_flags 00000222 != 00000022 ti-sysc 48046000.target-module: sysc_flags 00000222 != 00000022 ... Let's fix these warnings by adding SYSC_HAS_RESET_STATUS. Let's also remove the useless parentheses while at it. If it turns out we do have ti,sysc-omap4 compatible devices without a working SOFTRESET bit we can set up additional quirk handling for it. Signed-off-by:
-
Quinn Tran authored
[ Upstream commit c3b6a1d3 ] There are instances, though rare, where a LOGO request cannot be sent out and the thread in free session done can wait indefinitely. Fix this by putting an upper bound to sleep. Link: https://lore.kernel.org/r/20190912180918.6436-3-hmadhani@marvell.comSigned-off-by:
Quinn Tran <qutran@marvell.com> Signed-off-by:
Himanshu Madhani <hmadhani@marvell.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Xiang Chen authored
[ Upstream commit 70054aa3 ] For pci device, need to disable device when probe failed after enabled device. Link: https://lore.kernel.org/r/1567818450-173315-1-git-send-email-chenxiang66@hisilicon.comSigned-off-by:
Xiang Chen <chenxiang66@hisilicon.com> Reviewed-by:
John Garry <john.garry@huawei.com> Signed-off-by:
-
Stanley Chu authored
[ Upstream commit f51913ee ] In some cases, hba may go through shutdown flow without successful initialization and then make system hang. For example, if ufshcd_change_power_mode() gets error and leads to ufshcd_hba_exit() to release resources of the host, future shutdown flow may hang the system since the host register will be accessed in unpowered state. To solve this issue, simply add checking to skip shutdown for above kind of situation. Link: https://lore.kernel.org/r/1568780438-28753-1-git-send-email-stanley.chu@mediatek.comSigned-off-by:
Stanley Chu <stanley.chu@mediatek.com> Acked-by:
Bean Huo <beanhuo@micron.com> Signed-off-by:
-
Balbir Singh authored
[ Upstream commit b224726d ] User space programs like udevd may try to read to partitions at the same time the driver detects a namespace is unusable, and may deadlock if revalidate_disk() is called while such a process is waiting to enter the frozen queue. On detecting a dead namespace, move the disk revalidate after unblocking dispatchers that may be holding bd_butex. changelog Suggested-by: Keith Busch <kbusch@kernel.org> Signed-off-by:
Balbir Singh <sblbir@amzn.com> Reviewed-by:
Keith Busch <kbusch@kernel.org> Signed-off-by:
Sagi Grimberg <sagi@grimberg.me> Signed-off-by:
-
- 17 Oct, 2019 9 commits
-
-
Greg Kroah-Hartman authored
-
Mark-PK Tsai authored
commit 310aa0a2 upstream. If we disable the compiler's auto-initialization feature, if -fplugin-arg-structleak_plugin-byref or -ftrivial-auto-var-init=pattern are disabled, arch_hw_breakpoint may be used before initialization after: 9a4903dd ("perf/hw_breakpoint: Split attribute parse and commit") On our ARM platform, the struct step_ctrl in arch_hw_breakpoint, which used to be zero-initialized by kzalloc(), may be used in arch_install_hw_breakpoint() without initialization. Signed-off-by:
Mark-PK Tsai <mark-pk.tsai@mediatek.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alix Wu <alix.wu@mediatek.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: YJ Chiang <yj.chiang@mediatek.com> Link: https://lkml.kernel.org/r/20190906060115.9460-1-mark-pk.tsai@mediatek.com [ Minor edits. ] Signed-off-by:
Ingo Molnar <mingo@kernel.org> Cc: Doug Anderson <dianders@chromium.org> Signed-off-by:
-
Jon Derrick authored
commit e3dffa4f upstream. VMD maps child device config spaces to the VMD Config BAR linearly regardless of the starting bus offset. Because of this, the config address decode must ignore starting bus offsets when mapping the BDF to the config space address. Fixes: 2a5a9c9a ("PCI: vmd: Add offset to bus numbers if necessary") Signed-off-by:
Jon Derrick <jonathan.derrick@intel.com> Signed-off-by:
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: stable@vger.kernel.org # v5.2+ Signed-off-by:
Sushma Kalakota <sushmax.kalakota@intel.com> Signed-off-by:
-
Janakarajan Natarajan authored
commit 454de1e7 upstream. As per "AMD64 Architecture Programmer's Manual Volume 3: General-Purpose and System Instructions", MWAITX EAX[7:4]+1 specifies the optional hint of the optimized C-state. For C0 state, EAX[7:4] should be set to 0xf. Currently, a value of 0xf is set for EAX[3:0] instead of EAX[7:4]. Fix this by changing MWAITX_DISABLE_CSTATES from 0xf to 0xf0. This hasn't had any implications so far because setting reserved bits in EAX is simply ignored by the CPU. [ bp: Fixup comment in delay_mwaitx() and massage. ] Signed-off-by:
Janakarajan Natarajan <Janakarajan.Natarajan@amd.com> Signed-off-by:
Borislav Petkov <bp@suse.de> Cc: Frederic Weisbecker <frederic@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "x86@kernel.org" <x86@kernel.org> Cc: Zhenzhong Duan <zhenzhong.duan@oracle.com> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/20191007190011.4859-1-Janakarajan.Natarajan@amd.comSigned-off-by:
-
Nuno Sá authored
commit 30945d31 upstream. Both HWMON_P_MIN_ALARM and HWMON_P_MAX_ALARM were using BIT(hwmon_power_max_alarm). Fixes: aa7f29b0 ("hwmon: Add support for power min, lcrit, min_alarm and lcrit_alarm") CC: <stable@vger.kernel.org> Signed-off-by:
Nuno Sá <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20190924124945.491326-2-nuno.sa@analog.comSigned-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Steven Rostedt (VMware) authored
commit 194c2c74 upstream. As instances may have different tracers available, we need to look at the trace_array descriptor that shows the list of the available tracers for the instance. But there's a race between opening the file and an admin deleting the instance. The trace_array_get() needs to be called before accessing the trace_array. Cc: stable@vger.kernel.org Fixes: 607e2ea1 ("tracing: Set up infrastructure to allow tracers for instances") Signed-off-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
-
Steven Rostedt (VMware) authored
commit 9ef16693 upstream. The ftrace set_ftrace_filter and set_ftrace_notrace files are specific for an instance now. They need to take a reference to the instance otherwise there could be a race between accessing the files and deleting the instance. It wasn't until the :mod: caching where these file operations started referencing the trace_array directly. Cc: stable@vger.kernel.org Fixes: 673feb9d ("ftrace: Add :mod: caching infrastructure to trace_array") Signed-off-by:
-
Srivatsa S. Bhat (VMware) authored
commit fc64e4ad upstream. max_latency is intended to record the maximum ever observed hardware latency, which may occur in either part of the loop (inner/outer). So we need to also consider the outer-loop sample when updating max_latency. Link: http://lkml.kernel.org/r/157073345463.17189.18124025522664682811.stgit@srivatsa-ubuntu Fixes: e7c15cd8 ("tracing: Added hardware latency tracer") Cc: stable@vger.kernel.org Signed-off-by:
Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu> Signed-off-by:
-
Srivatsa S. Bhat (VMware) authored
commit 98dc19c1 upstream. nmi_total_ts is supposed to record the total time spent in *all* NMIs that occur on the given CPU during the (active portion of the) sampling window. However, the code seems to be overwriting this variable for each NMI, thereby only recording the time spent in the most recent NMI. Fix it by accumulating the duration instead. Link: http://lkml.kernel.org/r/157073343544.17189.13911783866738671133.stgit@srivatsa-ubuntu Fixes: 7b2c8625 ("tracing: Add NMI tracing in hwlat detector") Cc: stable@vger.kernel.org Signed-off-by:
-
