- 05 Jul, 2017 40 commits
-
-
Ivan Vecera authored
[ Upstream commit 34393529 ] During interface opening MAC address stored in netdev->dev_addr is programmed in the HW with exception of BE3 VFs where the initial MAC is programmed by parent PF. This is OK when MAC address is not changed when an interfaces is down. In this case the requested MAC is stored to netdev->dev_addr and later is stored into HW during opening. But this is not done for all BE3 VFs so the NIC HW does not know anything about this change and all traffic is filtered. This is the case of bonding if fail_over_mac == 0 where the MACs of the slaves are changed while they are down. The be2net behavior is too restrictive because if a BE3 VF has the FILTMGMT privilege then it is able to modify its MAC without any restriction. To solve the described problem the driver should take care about these privileged BE3 VFs so the MAC is programmed during opening. And by contrast unpriviled BE3 VFs should not be allowed to change its MAC in any case. Cc: Sathya Perla <sathya.perla@broadcom.com> Cc: Ajit Khaparde <ajit.khaparde@broadcom.com> Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com> Cc: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by:
Ivan Vecera <cera@cera.cz> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <alexander.levin@verizon.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ivan Vecera authored
[ Upstream commit 6d928ae5 ] BE3 VFs without FILTMGMT privilege are not allowed to modify its MAC, VLAN table and UC/MC lists. So don't try to delete MAC on such VFs. Cc: Sathya Perla <sathya.perla@broadcom.com> Cc: Ajit Khaparde <ajit.khaparde@broadcom.com> Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com> Cc: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by:
-
Ivan Vecera authored
[ Upstream commit fe68d8bf ] Return value from be_mcc_notify_wait() contains a base completion status together with an additional status. The base_status() macro need to be used to access base status. Fixes: e3a7ae2c be2net: Changing MAC Address of a VF was broken Cc: Sathya Perla <sathya.perla@broadcom.com> Cc: Ajit Khaparde <ajit.khaparde@broadcom.com> Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com> Cc: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by:
-
Amelie Delaunay authored
[ Upstream commit ca02954a ] USBTrdTim must be programmed to 0x5 when phy has a UTMI+ 16-bit wide interface or 0x9 when it has a 8-bit wide interface. GUSBCFG reset value (Value After Reset: 0x1400) sets USBTrdTim to 0x5. In case of 8-bit UTMI+, without clearing GUSBCFG.USBTRDTIM mask, USBTrdTim results in 0xD (0x5 | 0x9). That's why we need to clear GUSBCFG.USBTRDTIM mask before setting USBTrdTim value, to ensure USBTrdTim is correctly set in case of 8-bit UTMI+. Signed-off-by:
Amelie Delaunay <amelie.delaunay@st.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Heiko Carstens authored
[ Upstream commit e991c24d ] We have quite a lot of code that depends on the order of the __ctl_load inline assemby and subsequent memory accesses, like e.g. disabling lowcore protection and the writing to lowcore. Since the __ctl_load macro does not have memory barrier semantics, nor any other dependencies the compiler is, theoretically, free to shuffle code around. Or in other words: storing to lowcore could happen before lowcore protection is disabled. In order to avoid this class of potential bugs simply add a full memory barrier to the __ctl_load macro. Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Nikita Yushchenko authored
[ Upstream commit 602d9858 ] Some drivers do depend on page mappings to be page aligned. Swiotlb already enforces such alignment for mappings greater than page, extend that to page-sized mappings as well. Without this fix, nvme hits BUG() in nvme_setup_prps(), because that routine assumes page-aligned mappings. Signed-off-by:
Nikita Yushchenko <nikita.yoush@cogentembedded.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
Sagi Grimberg <sagi@grimberg.me> Signed-off-by:
Konrad Rzeszutek Wilk <konrad@kernel.org> Signed-off-by:
-
Dave Kleikamp authored
[ Upstream commit 4d22c75d ] If the last section of a core file ends with an unmapped or zero page, the size of the file does not correspond with the last dump_skip() call. gdb complains that the file is truncated and can be confusing to users. After all of the vma sections are written, make sure that the file size is no smaller than the current file position. This problem can be demonstrated with gdb's bigcore testcase on the sparc architecture. Signed-off-by:
Dave Kleikamp <dave.kleikamp@oracle.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: linux-fsdevel@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Shaohua Li authored
[ Upstream commit a12f1ae6 ] lockdep reports a warnning. file_start_write/file_end_write only acquire/release the lock for regular files. So checking the files in aio side too. [ 453.532141] ------------[ cut here ]------------ [ 453.533011] WARNING: CPU: 1 PID: 1298 at ../kernel/locking/lockdep.c:3514 lock_release+0x434/0x670 [ 453.533011] DEBUG_LOCKS_WARN_ON(depth <= 0) [ 453.533011] Modules linked in: [ 453.533011] CPU: 1 PID: 1298 Comm: fio Not tainted 4.9.0+ #964 [ 453.533011] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.0-1.fc24 04/01/2014 [ 453.533011] ffff8803a24b7a70 ffffffff8196cffb ffff8803a24b7ae8 0000000000000000 [ 453.533011] ffff8803a24b7ab8 ffffffff81091ee1 ffff8803a5dba700 00000dba00000008 [ 453.533011] ffffed0074496f59 ffff8803a5dbaf54 ffff8803ae0f8488 fffffffffffffdef [ 453.533011] Call Trace: [ 453.533011] [<ffffffff8196cffb>] dump_stack+0x67/0x9c [ 453.533011] [<ffffffff81091ee1>] __warn+0x111/0x130 [ 453.533011] [<ffffffff81091f97>] warn_slowpath_fmt+0x97/0xb0 [ 453.533011] [<ffffffff81091f00>] ? __warn+0x130/0x130 [ 453.533011] [<ffffffff8191b789>] ? blk_finish_plug+0x29/0x60 [ 453.533011] [<ffffffff811205d4>] lock_release+0x434/0x670 [ 453.533011] [<ffffffff8198af94>] ? import_single_range+0xd4/0x110 [ 453.533011] [<ffffffff81322195>] ? rw_verify_area+0x65/0x140 [ 453.533011] [<ffffffff813aa696>] ? aio_write+0x1f6/0x280 [ 453.533011] [<ffffffff813aa6c9>] aio_write+0x229/0x280 [ 453.533011] [<ffffffff813aa4a0>] ? aio_complete+0x640/0x640 [ 453.533011] [<ffffffff8111df20>] ? debug_check_no_locks_freed+0x1a0/0x1a0 [ 453.533011] [<ffffffff8114793a>] ? debug_lockdep_rcu_enabled.part.2+0x1a/0x30 [ 453.533011] [<ffffffff81147985>] ? debug_lockdep_rcu_enabled+0x35/0x40 [ 453.533011] [<ffffffff812a92be>] ? __might_fault+0x7e/0xf0 [ 453.533011] [<ffffffff813ac9bc>] do_io_submit+0x94c/0xb10 [ 453.533011] [<ffffffff813ac2ae>] ? do_io_submit+0x23e/0xb10 [ 453.533011] [<ffffffff813ac070>] ? SyS_io_destroy+0x270/0x270 [ 453.533011] [<ffffffff8111d7b3>] ? mark_held_locks+0x23/0xc0 [ 453.533011] [<ffffffff8100201a>] ? trace_hardirqs_on_thunk+0x1a/0x1c [ 453.533011] [<ffffffff813acb90>] SyS_io_submit+0x10/0x20 [ 453.533011] [<ffffffff824f96aa>] entry_SYSCALL_64_fastpath+0x18/0xad [ 453.533011] [<ffffffff81119190>] ? trace_hardirqs_off_caller+0xc0/0x110 [ 453.533011] ---[ end trace b2fbe664d1cc0082 ]--- Cc: Dmitry Monakhov <dmonakhov@openvz.org> Cc: Jan Kara <jack@suse.cz> Cc: Christoph Hellwig <hch@lst.de> Cc: Al Viro <viro@zeniv.linux.org.uk> Reviewed-by:
Shaohua Li <shli@fb.com> Signed-off-by:
-
Jiri Olsa authored
[ Upstream commit 18e7a45a ] As Peter suggested [1] rejecting non sampling PEBS events, because they dont make any sense and could cause bugs in the NMI handler [2]. [1] http://lkml.kernel.org/r/20170103094059.GC3093@worktop [2] http://lkml.kernel.org/r/1482931866-6018-3-git-send-email-jolsa@kernel.orgSigned-off-by:
Jiri Olsa <jolsa@redhat.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vince@deater.net> Cc: Vince Weaver <vincent.weaver@maine.edu> Link: http://lkml.kernel.org/r/20170103142454.GA26251@kravaSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Peter Zijlstra authored
[ Upstream commit 63cae12b ] There is problem with installing an event in a task that is 'stuck' on an offline CPU. Blocked tasks are not dis-assosciated from offlined CPUs, after all, a blocked task doesn't run and doesn't require a CPU etc.. Only on wakeup do we ammend the situation and place the task on a available CPU. If we hit such a task with perf_install_in_context() we'll loop until either that task wakes up or the CPU comes back online, if the task waking depends on the event being installed, we're stuck. While looking into this issue, I also spotted another problem, if we hit a task with perf_install_in_context() that is in the middle of being migrated, that is we observe the old CPU before sending the IPI, but run the IPI (on the old CPU) while the task is already running on the new CPU, things also go sideways. Rework things to rely on task_curr() -- outside of rq->lock -- which is rather tricky. Imagine the following scenario where we're trying to install the first event into our task 't': CPU0 CPU1 CPU2 (current == t) t->perf_event_ctxp[] = ctx; smp_mb(); cpu = task_cpu(t); switch(t, n); migrate(t, 2); switch(p, t); ctx = t->perf_event_ctxp[]; // must not be NULL smp_function_call(cpu, ..); generic_exec_single() func(); spin_lock(ctx->lock); if (task_curr(t)) // false add_event_to_ctx(); spin_unlock(ctx->lock); perf_event_context_sched_in(); spin_lock(ctx->lock); // sees event So its CPU0's store of t->perf_event_ctxp[] that must not go 'missing'. Because if CPU2's load of that variable were to observe NULL, it would not try to schedule the ctx and we'd have a task running without its counter, which would be 'bad'. As long as we observe !NULL, we'll acquire ctx->lock. If we acquire it first and not see the event yet, then CPU0 must observe task_curr() and retry. If the install happens first, then we must see the event on sched-in and all is well. I think we can translate the first part (until the 'must not be NULL') of the scenario to a litmus test like: C C-peterz { } P0(int *x, int *y) { int r1; WRITE_ONCE(*x, 1); smp_mb(); r1 = READ_ONCE(*y); } P1(int *y, int *z) { WRITE_ONCE(*y, 1); smp_store_release(z, 1); } P2(int *x, int *z) { int r1; int r2; r1 = smp_load_acquire(z); smp_mb(); r2 = READ_ONCE(*x); } exists (0:r1=0 /\ 2:r1=1 /\ 2:r2=0) Where: x is perf_event_ctxp[], y is our tasks's CPU, and z is our task being placed on the rq of CPU2. The P0 smp_mb() is the one added by this patch, ordering the store to perf_event_ctxp[] from find_get_context() and the load of task_cpu() in task_function_call(). The smp_store_release/smp_load_acquire model the RCpc locking of the rq->lock and the smp_mb() of P2 is the context switch switching from whatever CPU2 was running to our task 't'. This litmus test evaluates into: Test C-peterz Allowed States 7 0:r1=0; 2:r1=0; 2:r2=0; 0:r1=0; 2:r1=0; 2:r2=1; 0:r1=0; 2:r1=1; 2:r2=1; 0:r1=1; 2:r1=0; 2:r2=0; 0:r1=1; 2:r1=0; 2:r2=1; 0:r1=1; 2:r1=1; 2:r2=0; 0:r1=1; 2:r1=1; 2:r2=1; No Witnesses Positive: 0 Negative: 7 Condition exists (0:r1=0 /\ 2:r1=1 /\ 2:r2=0) Observation C-peterz Never 0 7 Hash=e427f41d9146b2a5445101d3e2fcaa34 And the strong and weak model agree. Reported-by:
Mark Rutland <mark.rutland@arm.com> Tested-by:
-
Tobias Klauser authored
[ Upstream commit 45382862 ] info->si_addr is of type void __user *, so it should be compared against something from the same address space. This fixes the following sparse error: arch/x86/mm/mpx.c:296:27: error: incompatible types in comparison expression (different address spaces) Signed-off-by:
Tobias Klauser <tklauser@distanz.ch> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by:
-
Len Brown authored
[ Upstream commit 695085b4 ] The Intel Denverton microserver uses a 25 MHz TSC crystal, so we can derive its exact [*] TSC frequency using CPUID and some arithmetic, eg.: TSC: 1800 MHz (25000000 Hz * 216 / 3 / 1000000) [*] 'exact' is only as good as the crystal, which should be +/- 20ppm Signed-off-by:
Len Brown <len.brown@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/306899f94804aece6d8fa8b4223ede3b48dbb59c.1484287748.git.len.brown@intel.comSigned-off-by:
-
Felix Fietkau authored
[ Upstream commit 43071d8f ] ibss and mesh modes copy the ht capabilites from the band without overriding the SMPS state. Unfortunately the default value 0 for the SMPS field means static SMPS instead of disabled. This results in HT ibss and mesh setups using only single-stream rates, even though SMPS is not supposed to be active. Initialize SMPS to disabled for all bands on ieee80211_hw_register to ensure that the value is sane where it is not overriden with the real SMPS state. Reported-by:
Elektra Wagenrad <onelektra@gmx.net> Signed-off-by:
Felix Fietkau <nbd@nbd.name> [move VHT TODO comment to a better place] Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Stefan Hajnoczi authored
[ Upstream commit d47d1d27 ] The read_pmem() function uses memcpy_mcsafe() on x86 where an EFAULT error code indicates a failed read. Block I/O should use EIO to indicate failure. Other pmem code paths (like bad blocks) already use EIO so let's be consistent. This fixes compatibility with consumers like btrfs that try to parse the specific error code rather than treat all errors the same. Reviewed-by:
Jeff Moyer <jmoyer@redhat.com> Signed-off-by:
Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
-
Rex Zhu authored
[ Upstream commit ab8db87b ] Program HardMin based on the vce_arbiter.ecclk if ecclk is 0, disable ECLK DPM 0. Otherwise VCE could hang if switching SCLK from DPM 0 to 6/7 Signed-off-by:
Rex Zhu <Rex.Zhu@amd.com> Acked-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Rex Zhu authored
[ Upstream commit 3731d12d ] can fix Bug 191281: vce ib test failed. when vce idle, set vce clock gate, so the clock in vce domain will be disabled. when need to encode, disable vce clock gate, enable the clocks to vce engine. Signed-off-by:
-
Alex Deucher authored
[ Upstream commit ef736d39 ] Special MC ucode is required for these memory configurations. Acked-by:
Edward O'Callaghan <funfunctor@folklore1984.net> Signed-off-by:
-
Vadim Lomovtsev authored
[ Upstream commit 7aa48655 ] While probing BGX we requesting appropriate QLM for it's configuration and get LMAC count by that request. Then, while reading configured MAC values from SSDT table we need to save them in proper mapping: BGX[i]->lmac[j].mac = <MAC value> to later provide for initialization stuff. In order to fill such mapping properly we need to add lmac index to be used while acpi initialization since at this moment bgx->lmac_count already contains actual value. Signed-off-by:
Vadim Lomovtsev <Vadim.Lomovtsev@caviumnetworks.com> Signed-off-by:
-
Ard Biesheuvel authored
[ Upstream commit 41c066f2 ] When CONFIG_RANDOMIZE_MODULE_REGION_FULL=y, the offset between loaded modules and the core kernel may exceed 4 GB, putting symbols exported by the core kernel out of the reach of the ordinary adrp/add instruction pairs used to generate relative symbol references. So make the adr_l macro emit a movz/movk sequence instead when executing in module context. While at it, remove the pointless special case for the stack pointer. Acked-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Kevin Hilman authored
[ Upstream commit c5a2a394 ] The correct error checking for dma_map_single() is to use dma_mapping_error(). Signed-off-by:
Kevin Hilman <khilman@baylibre.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Roberto Sassu authored
[ Upstream commit cd60be49 ] Set variables initialized in lpfc_sli4_alloc_resource_identifiers() to NULL if an error occurred. Otherwise, lpfc_sli4_driver_resource_unset() attempts to free the memory again. Signed-off-by:
Roberto Sassu <rsassu@suse.de> Signed-off-by:
Johannes Thumshirn <jthumshirn@suse.de> Acked-by:
James Smart <james.smart@broadcom.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Brendan McGrath authored
[ Upstream commit a89af4ab ] Support for the Asus Touchpad was recently added. It turns out this device can fail initialisation (and become unusable) when the RESET command is sent too soon after the POWER ON command. Unfortunately the i2c-hid specification does not specify the need for a delay between these two commands. But it was discovered the Windows driver has a 1ms delay. As a result, this patch modifies the i2c-hid module to add a sleep inbetween the POWER ON and RESET commands which lasts between 1ms and 5ms. See https://github.com/vlasenko/hid-asus-dkms/issues/24 for further details. Signed-off-by:
Brendan McGrath <redmcg@redmandi.dyndns.org> Reviewed-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Colin King authored
[ Upstream commit ad5013d5 ] When x86_pmu.num_counters is 32 the shift of the integer constant 1 is exceeding 32bit and therefor undefined behaviour. Fix this by shifting 1ULL instead of 1. Reported-by: CoverityScan CID#1192105 ("Bad bit shift operation") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Kan Liang <kan.liang@intel.com> Cc: Stephane Eranian <eranian@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Link: http://lkml.kernel.org/r/20170111114310.17928-1-colin.king@canonical.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Johannes Berg authored
[ Upstream commit d2941df8 ] When an associated station changes its VHT operating mode this can/will affect the bandwidth it's using, and consequently we must recalculate the minimum bandwidth we need to use. Failure to do so can lead to one of two scenarios: 1) we use a too high bandwidth, this is benign 2) we use a too narrow bandwidth, causing rate control and actual PHY configuration to be out of sync, which can in turn cause problems/crashes Signed-off-by:
-
Russell King authored
[ Upstream commit a13c0652 ] When an Marvell 88E1512 PHY is connected to a nic in SGMII mode, the fiber page is used for the SGMII host-side connection. The PHY driver notices that SUPPORTED_FIBRE is set, so it tries reading the fiber page for the link status, and ends up reading the MAC-side status instead of the outgoing (copper) link. This leads to incorrect results reported via ethtool. If the PHY is connected via SGMII to the host, ignore the fiber page. However, continue to allow the existing power management code to suspend and resume the fiber page. Fixes: 6cfb3bcc ("Marvell phy: check link status in case of fiber link.") Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Andy Shevchenko authored
[ Upstream commit 17fab473 ] There are two bits in the PADCFG0 register to configure direction, one per TX/RX buffers. For now we wrongly assume that the GPIO is always requested before it is being used, which is not true when the GPIO is used through irqchip. In this case the GPIO is never requested and we never enable RX buffer for it. Fix this by setting both bits accordingly. Reported-by:
Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Prarit Bhargava authored
[ Upstream commit 6d6daa20 ] hswep_uncore_cpu_init() uses a hardcoded physical package id 0 for the boot cpu. This works as long as the boot CPU is actually on the physical package 0, which is normaly the case after power on / reboot. But it fails with a NULL pointer dereference when a kdump kernel is started on a secondary socket which has a different physical package id because the locigal package translation for physical package 0 does not exist. Use the logical package id of the boot cpu instead of hard coded 0. [ tglx: Rewrote changelog once more ] Fixes: cf6d445f ("perf/x86/uncore: Track packages, not per CPU data") Signed-off-by:
Prarit Bhargava <prarit@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Borislav Petkov <bp@suse.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Harish Chegondi <harish.chegondi@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Kan Liang <kan.liang@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1483628965-2890-1-git-send-email-prarit@redhat.comSigned-off-by:
-
Lucas Stach authored
[ Upstream commit 3546fb0c ] After rollover of the IOVA space, we want to get a low IOVA address, otherwise the the games we play by remembering the last IOVA are pointless. When we search for a free hole with DRM_MM_SEARCH_DEFAULT, drm_mm will pop the next entry from the free holes stack, which will likely be a high IOVA. By using DRM_MM_SEARCH_BELOW we can trick drm_mm into reversing the search and provide us with a low IOVA. Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Reviewed-by:
Wladimir van der Laan <laanwj@gmail.com> Signed-off-by:
-
John Crispin authored
[ Upstream commit 61976fff ] When the binding was defined, I was not aware that mt2701 was an earlier version of the SoC. For sake of consistency, the ethernet driver should use mt2701 inside the compat string as this is the earliest SoC with the ethernet core. The ethernet driver is currently of no real use until we finish and upstream the DSA driver. There are no users of this binding yet. It should be safe to fix this now before it is too late and we need to provide backward compatibility for the mt7623-eth compat string. Reported-by:
Sean Wang <sean.wang@mediatek.com> Signed-off-by:
John Crispin <john@phrozen.org> Reviewed-by:
Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by:
-
Jiri Slaby authored
[ Upstream commit ff7a28a0 ] When a system panics, the "Rebooting in X seconds.." message is never printed because it lacks a new line. Fix it. Link: http://lkml.kernel.org/r/20170119114751.2724-1-jslaby@suse.czSigned-off-by:
Jiri Slaby <jslaby@suse.cz> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Thomas Huth authored
[ Upstream commit 23d28a85 ] When using the ibmveth driver in a KVM/QEMU based VM, it currently always prints out a scary error message like this when it is started: ibmveth 71000003 (unregistered net_device): unable to change checksum offload settings. 1 rc=-2 ret_attr=71000003 This happens because the driver always tries to enable the checksum offloading without checking for the availability of this feature first. QEMU does not support checksum offloading for the spapr-vlan device, thus we always get the error message here. According to the LoPAPR specification, the "ibm,illan-options" property of the corresponding device tree node should be checked first to see whether the H_ILLAN_ATTRIUBTES hypercall and thus the checksum offloading feature is available. Thus let's do this in the ibmveth driver, too, so that the error message is really only limited to cases where something goes wrong, and does not occur if the feature is just missing. Signed-off-by:
Thomas Huth <thuth@redhat.com> Signed-off-by:
-
Balakrishnan Raman authored
[ Upstream commit efb5f68f ] Mac aging is applicable only for dynamically learnt remote mac entries. Check for user configured static remote mac entries and skip aging. Signed-off-by:
Balakrishnan Raman <ramanb@cumulusnetworks.com> Signed-off-by:
Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 21b995a9 ] Since ip6_tnl_parse_tlv_enc_lim() can call pskb_may_pull(), we must reload any pointer that was related to skb->head (or skb->data), or risk use after free. Fixes: c12b395a ("gre: Support GRE over IPv6") Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Dmitry Kozlov <xeb@mail.ru> Signed-off-by:
-
Michael S. Tsirkin authored
[ Upstream commit d0fa28f0 ] I don't have any guests with PAGE_SIZE > 64k but the code seems to be clearly broken in that case as PAGE_SIZE / MERGEABLE_BUFFER_ALIGN will need more than 8 bit and so the code in mergeable_ctx_to_buf_address does not give us the actual true size. Cc: John Fastabend <john.fastabend@gmail.com> Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Ido Schimmel authored
[ Upstream commit a59b7e02 ] mlxsw_sp_nexthop_group_mac_update() is called in one of two cases: 1) When the MAC of a nexthop needs to be updated 2) When the size of a nexthop group has changed In the second case the adjacency entries for the nexthop group need to be reallocated from the adjacency table. In this case we must write to the entries the MAC addresses of all the nexthops that should be offloaded and not only those whose MAC changed. Otherwise, these entries would be filled with garbage data, resulting in packet loss. Fixes: a7ff87ac ("mlxsw: spectrum_router: Implement next-hop routing") Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Greg Kurz authored
[ Upstream commit bd00fdf1 ] The recently added mediated VFIO driver doesn't know about powerpc iommu. It thus doesn't register a struct iommu_table_group in the iommu group upon device creation. The iommu_data pointer hence remains null. This causes a kernel oops when userspace tries to set the iommu type of a container associated with a mediated device to VFIO_SPAPR_TCE_v2_IOMMU. [ 82.585440] mtty mtty: MDEV: Registered [ 87.655522] iommu: Adding device 83b8f4f2-509f-382f-3c1e-e6bfe0fa1001 to group 10 [ 87.655527] vfio_mdev 83b8f4f2-509f-382f-3c1e-e6bfe0fa1001: MDEV: group_id = 10 [ 116.297184] Unable to handle kernel paging request for data at address 0x00000030 [ 116.297389] Faulting instruction address: 0xd000000007870524 [ 116.297465] Oops: Kernel access of bad area, sig: 11 [#1] [ 116.297611] SMP NR_CPUS=2048 [ 116.297611] NUMA [ 116.297627] PowerNV ... [ 116.297954] CPU: 33 PID: 7067 Comm: qemu-system-ppc Not tainted 4.10.0-rc5-mdev-test #8 [ 116.297993] task: c000000e7718b680 task.stack: c000000e77214000 [ 116.298025] NIP: d000000007870524 LR: d000000007870518 CTR: 0000000000000000 [ 116.298064] REGS: c000000e77217990 TRAP: 0300 Not tainted (4.10.0-rc5-mdev-test) [ 116.298103] MSR: 9000000000009033 <SF,HV,EE,ME,IR,DR,RI,LE> [ 116.298107] CR: 84004444 XER: 00000000 [ 116.298154] CFAR: c00000000000888c DAR: 0000000000000030 DSISR: 40000000 SOFTE: 1 GPR00: d000000007870518 c000000e77217c10 d00000000787b0ed c000000eed2103c0 GPR04: 0000000000000000 0000000000000000 c000000eed2103e0 0000000f24320000 GPR08: 0000000000000104 0000000000000001 0000000000000000 d0000000078729b0 GPR12: c00000000025b7e0 c00000000fe08400 0000000000000001 000001002d31d100 GPR16: 000001002c22c850 00003ffff315c750 0000000043145680 0000000043141bc0 GPR20: ffffffffffffffed fffffffffffff000 0000000020003b65 d000000007706018 GPR24: c000000f16cf0d98 d000000007706000 c000000003f42980 c000000003f42980 GPR28: c000000f1575ac00 c000000003f429c8 0000000000000000 c000000eed2103c0 [ 116.298504] NIP [d000000007870524] tce_iommu_attach_group+0x10c/0x360 [vfio_iommu_spapr_tce] [ 116.298555] LR [d000000007870518] tce_iommu_attach_group+0x100/0x360 [vfio_iommu_spapr_tce] [ 116.298601] Call Trace: [ 116.298610] [c000000e77217c10] [d000000007870518] tce_iommu_attach_group+0x100/0x360 [vfio_iommu_spapr_tce] (unreliable) [ 116.298671] [c000000e77217cb0] [d0000000077033a0] vfio_fops_unl_ioctl+0x278/0x3e0 [vfio] [ 116.298713] [c000000e77217d40] [c0000000002a3ebc] do_vfs_ioctl+0xcc/0x8b0 [ 116.298745] [c000000e77217de0] [c0000000002a4700] SyS_ioctl+0x60/0xc0 [ 116.298782] [c000000e77217e30] [c00000000000b220] system_call+0x38/0xfc [ 116.298812] Instruction dump: [ 116.298828] 7d3f4b78 409effc8 3d220000 e9298020 3c800140 38a00018 608480c0 e8690028 [ 116.298869] 4800249d e8410018 7c7f1b79 41820230 <e93e0030> 2fa90000 419e0114 e9090020 [ 116.298914] ---[ end trace 1e10b0ced08b9120 ]--- This patch fixes the oops. Reported-by:
Vaibhav Jain <vaibhav@linux.vnet.ibm.com> Signed-off-by:
Greg Kurz <groug@kaod.org> Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
-
Ding Pixel authored
[ Upstream commit c5f21c9f ] Return success when the ring is properly initialized, otherwise return failure. Tonga SRIOV VF doesn't have UVD and VCE engines, the initialization of these IPs is bypassed. The system crashes if application submit IB to their rings which are not ready to use. It could be a common issue if IP having ring buffer is disabled for some reason on specific ASIC, so it should check the ring being ready to use. Bug: amdgpu_test crashes system on Tonga VF. Signed-off-by:
Ding Pixel <Pixel.Ding@amd.com> Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit 4078b76c ] We need to check the return value of phy_connect_direct() in dsa_slave_phy_connect() otherwise we may be continuing the initialization of a slave network device with a PHY that already attached somewhere else and which will soon be in error because the PHY device is in error. The conditions for such an error to occur are that we have a port of our switch that is not disabled, and has the same port number as a PHY address (say both 5) that can be probed using the DSA slave MII bus. We end-up having this slave network device find a PHY at the same address as our port number, and we try to attach to it. A slave network (e.g: port 0) has already attached to our PHY device, and we try to re-attach it with a different network device, but since we ignore the error we would end-up initializating incorrect device references by the time the slave network interface is opened. The code has been (re)organized several times, making it hard to provide an exact Fixes tag, this is a bugfix nonetheless. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Lendacky, Thomas authored
[ Upstream commit 738f7f64 ] The xgbe_init() routine returns a return code indicating success or failure, but the return code is not checked. Add code to xgbe_init() to issue a message when failures are seen and add code to check the xgbe_init() return code. Signed-off-by:
Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
-
Zach Ploskey authored
[ Upstream commit cfee5d63 ] On Ideapad laptops, ACPI event 1 is currently not handled. Many models log "ideapad_laptop: Unknown event: 1" every 20 seconds or so while running on battery power. Some convertible laptops receive this event when switching in and out of tablet mode. This adds and additional case for event 1 in ideapad_acpi_notify to call ideapad_input_report(priv, vpc_bit), so that the event is reported to userspace and we avoid unnecessary logging. Fixes bug #107481 (https://bugzilla.kernel.org/show_bug.cgi?id=107481) Fixes bug #65751 (https://bugzilla.kernel.org/show_bug.cgi?id=65751) Signed-off-by:
Zach Ploskey <zach@ploskey.com> Signed-off-by:
-
