Fix the following sparse warnings:
drivers/net/wireless/purelifi/plfxlc/chip.c:36:31: sparse: expected unsigned short [usertype] beacon_interval
drivers/net/wireless/purelifi/plfxlc/chip.c:36:31: sparse: got restricted __le16 [usertype]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Srinivasan Raju <srini.raju@purelifi.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502150133.6052-1-srini.raju@purelifi.com

Defining local versions of NAPI_POLL_WEIGHT with the same
values in the drivers just makes refactoring harder.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220429174643.196994-2-kuba@kernel.org

After scan aborts we still receive some hw scan c2h packets, and
processing these c2h commands will change current channel. If device
already connect to other AP, driver will set wrong op channel due
to current channel changed. The disconnection happens when hw scan back
to wrong op channel that device can't receive beacon from AP. To fix
this issue, we ignore the late c2h if we are not scanning, and set
current channel back to op channel after scan to align the FW behavior.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220428020521.8015-3-pkshih@realtek.com

Correct the judgment to let beacon filter disable after disconnection.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220428020521.8015-2-pkshih@realtek.com

Each chip have best ampdu density value, the correct setting can improve
throughput performance.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220428020521.8015-1-pkshih@realtek.com

Eliminate the follow versioncheck warning:

./drivers/net/wireless/purelifi/plfxlc/usb.c: 20 linux/version.h not
needed.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220429075459.72029-1-jiapeng.chong@linux.alibaba.com

Eliminate the following coccicheck warning:
./drivers/net/wireless/realtek/rtw89/rtw8852c.c:2556:2-3: Unneeded
semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220427003142.107916-1-yang.lee@linux.alibaba.com

Fix the following coccicheck warning:

drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a1ant.c:1604:2-4:
WARNING: possible condition with no effect (if == else).
Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220425031725.5808-1-guozhengkui@vivo.com

This uses ISO3166 country code and 0 rev on brcmfmac43602 chips.
Without this patch 80 MHz width is not selected on 5 GHz channels.

Commit a21bf90e ("brcmfmac: use ISO3166 country code and 0 rev as
fallback on some devices") provides a way to specify chips for using the
fallback case.

Before commit 151a7c12 ("Revert "brcmfmac: use ISO3166 country code
and 0 rev as fallback"") brcmfmac43602 devices works correctly and for
this specific case 80 MHz width is selected.
Signed-off-by: Hamid Zamani <hzamani.cs91@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220423111237.60892-1-hzamani.cs91@gmail.com

Using not existing queues can panic the kernel with rtl8180/rtl8185 cards.
Ignore the skb priority for those cards, they only have one tx queue. Pierre
Asselin (pa@panix.com) reported the kernel crash in the Gentoo forum:

https://forums.gentoo.org/viewtopic-t-1147832-postdays-0-postorder-asc-start-25.html

He also confirmed that this patch fixes the issue. In summary this happened:

After updating wpa_supplicant from 2.9 to 2.10 the kernel crashed with a
"divide error: 0000" when connecting to an AP. Control port tx now tries to
use IEEE80211_AC_VO for the priority, which wpa_supplicants starts to use in
2.10.

Since only the rtl8187se part of the driver supports QoS, the priority
of the skb is set to IEEE80211_AC_BE (2) by mac80211 for rtl8180/rtl8185
cards.

rtl8180 is then unconditionally reading out the priority and finally crashes on
drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c line 544 without this
patch:
	idx = (ring->idx + skb_queue_len(&ring->queue)) % ring->entries

"ring->entries" is zero for rtl8180/rtl8185 cards, tx_ring[2] never got
initialized.

Cc: stable@vger.kernel.org
Reported-by: pa@panix.com
Tested-by: pa@panix.com
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220422145228.7567-1-alexander@wetzel-home.de

Write the BIT_USB_SUS_DIS bit rather than BIT_BT_DIG_CLK_EN to the
REG_HCI_OPT_CTRL register for fixing failure to PCIe power on.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/YmLAzuyPr0P4Y6BP@ns.kevlo.org

With a recent change now it is possible to detect the strapping
option on SD8997, which allows to pick up a correct firmware
for either SDIO-SDIO or SDIO-UART.

This commit enables SDIO-UART firmware on SD8997.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220422090313.125857-3-andrejs.cainikovs@toradex.com

Some WiFi/Bluetooth modules might have different host connection
options, allowing to either use SDIO for both WiFi and Bluetooth,
or SDIO for WiFi and UART for Bluetooth. It is possible to detect
whether a module has SDIO-SDIO or SDIO-UART connection by reading
its host strap register.

This change introduces a way to automatically select appropriate
firmware depending of the connection method, and removes a need
of symlinking or overwriting the original firmware file with a
required one.

Host strap register used in this commit comes from the NXP driver [1]
hosted at Code Aurora.

[1] https://source.codeaurora.org/external/imx/linux-imx/tree/drivers/net/wireless/nxp/mxm_wifiex/wlan_src/mlinux/moal_sdio_mmc.c?h=rel_imx_5.4.70_2.3.2&id=688b67b2c7220b01521ffe560da7eee33042c7bd#n1274Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220422090313.125857-2-andrejs.cainikovs@toradex.com

This is a driver for pureLiFi X, XL, XC devices which use light to transmit
data, so they are not compatible with normal Wi-Fi devices. The driver uses
separate NL80211_BAND_LC band to distinguish from Wi-Fi.  The driver is based
on 802.11 softMAC Architecture and uses native 802.11 for configuration and
management. Station and Ad-Hoc modes are supported.

The driver is compiled and tested in ARM, x86 architectures and compiled in
powerpc architecture. This driver implementation has been based on the zd1211rw
driver.
Signed-off-by: Srinivasan Raju <srini.raju@purelifi.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220224182042.132466-3-srini.raju@purelifi.com

Add some chip_ops to support BT coexistence to work properly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-15-pkshih@realtek.com

Hardware reports PPDU status containing encoded channel index to driver,
so we decode it and then fill freq and band.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-14-pkshih@realtek.com

Read thermal value, and then we can use EWMA thermal value to do RF
calibrations if the value is changed over a threshold.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-13-pkshih@realtek.com

Three chip_ops are implemented in this patch. The ::set_txpwr_ctrl and
::init_txpwr_unit are called when we up interface and then configure TX
power registers to initial values. The ::set_txpwr_ctrl is to configure
'txpwr_ref' to make basic output TX power of OFDM and CCK rate to be the
same. The ::init_txpwr_unit is to initialize TSSI (a method to do TX power
compensation depends on thermal value) control and bandedge.

The ::set_txpwr is called once switching channel. First, it sets TX power
for each rate section (e.g. CCK, OFDM), and then sets TX power offset
between 1SS and 2SS rate. Finally, it sets TX power limit to prevent
power over regulation.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-12-pkshih@realtek.com

8852c propose new API to configure BB TX/RX path. Without fix patch, it
can't transmit any packet.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-11-pkshih@realtek.com

IQK results in hardware has two copies that are used by firmware to switch
these two to support MCC.

This H2C tell firmware the corresponding channel and band of each IQK
results, and currrent one.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-10-pkshih@realtek.com

When disconnecting, it warns somethings after power is off, and we can't
do HCI IO. So, add this patch to avoid below messages:

  rtw89_8852ce 0000:03:00.0: timed out to flush pci txch: 11
  rtw89_8852ce 0000:03:00.0: failed to pre-release fwcmd
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-9-pkshih@realtek.com

RPP is to report certain skb(s) can be freed, and TX BD indicates which
TX descriptors can be freed. Normally, TX BD is happened before RPP.
In low power mode, RPP can happen ahead, so change flow to handle this
case.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-8-pkshih@realtek.com

In low power mode, we need to pause PCI to configure IMR and PCI ring
index registers accordingly, because the regular registers are power-off
in this mode.

In the transition moment named paused in code, we can't touch ring index,
so don't kick off DMA immediately. Instead, queue them into pending queue,
and kick off after the moment.

There are three low power modes, which are RF off/clock gate/power gate,
but PCI enter low power mode in later two modes only. So, add a mask
to achieve this.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-7-pkshih@realtek.com

Normally, we re-enable interrupt by napi_poll, but for this special
situation, we must turn it on immediately because napi_poll isn't
scheduled.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-6-pkshih@realtek.com

In lower power mode, there are very low amount of RX, and it must process
in a separated function instead of schedule_napi(), because the existing
napi_poll does many things to optimize performance, but not all registers
can access in low power mode. The simple way is to use threadfn to process
the simple thing.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-5-pkshih@realtek.com

To reclaim TX BD, we need to read hardware reading index to determine if
any DMA is complete. Since this IO spends time, do this thing only if we
really need it when TX BD has no free buffer corresponding to target skb.

The experimental result shows that reading counter decreases from 26,000
to 130 per second.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-4-pkshih@realtek.com

RPWM/CPWM are registers that can set and check low power mode. Since chips
use different address, add a field to access them in common flow.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-3-pkshih@realtek.com

8852CE uses different but similar IMR/ISR registers, and its masks are also
different in various states, so add config_intr_mask ops to configure masks
according to under_recovery or low_power states.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-2-pkshih@realtek.com

Disable this capability to avoid timeout errors on certain platforms.
Without it, pci bus might stuck and leads to disconnection.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220420093058.31646-2-pkshih@realtek.com

This avoids below warning and makes compiler happy.
error: uninitialized symbol 'tim_offset'
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220420093058.31646-1-pkshih@realtek.com

Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220420090247.2588680-1-chi.minghao@zte.com.cn

Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220420090214.2588618-1-chi.minghao@zte.com.cn

During setting channel, we need to backup/restore and disable/enable some
settings. The settings include SCH (scheduler channel), PPDU status report,
and RF components, DFS and ADC.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-13-pkshih@realtek.com

BB does many settings during setting channel. First is to configure CCK
for 2G channels, and then basic channel and bandwidth settings with a
encoded channel index that will report to driver when we receive packets.
Configure spur elimination to avoid spur of CSI and NBI tones in certain
frequencies. Also, it initializes BT grant to arrange path sharing with
BT according to band. Finally, reset TSSI and BB hardware to ensure it
stays in initial state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-12-pkshih@realtek.com

Configure channel and bandwidth of MAC registers to work properly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-11-pkshih@realtek.com

Prepare functions to configure channel and bandwidth accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-10-pkshih@realtek.com

HFC is short for HCI flow control, and these parameters is used to
configure PCI quota for TX/RX.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-9-pkshih@realtek.com

Define efuse struct to access gain offset, and store them for further use
by setting channel.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-8-pkshih@realtek.com

Add parser for bb gain table and configure bb gain table for 8852c.
While ctrl_ch, obtain bb gain error settings and write them to phy.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-7-pkshih@realtek.com

chip_ops::bb_sethw is to initialize BB settings out of BB parameters
tables. Once switching channel or initialing, we do chip_ops::bb_reset to
reset hardware counters and states to make things in expectation.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-6-pkshih@realtek.com