The tx cleanup routine was stopping after 64 packets and this was causing
issues resulting in the ring not being completely cleaned.

This change updates the driver to clean the entire ring and if it doesn't
it then will retry on the next pass.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch changes the dma mapping to better support
skb_dma_map/skb_dma_unmap and addresses and redefines the tx hang logic to
be based off of time stamp instead of if the dma field is populated
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I've hit an issue on my system when I've been using RealTek RTL8139D cards in
bonding interface in mode balancing-alb. When I enslave a card, the current
active slave (bond->curr_active_slave) is not set and the link is therefore
not functional.

----
# cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.5.0 (November 4, 2008)

Bonding Mode: adaptive load balancing
Primary Slave: None
Currently Active Slave: None
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0

Slave Interface: eth1
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:1f:1f:01:2f:22
----

The thing that gets it right is when I unplug the cable and then I put it back
into the NIC. Then the current active slave is set to eth1 and link is working
just fine. Here is dmesg log with bonding DEBUG messages turned on:
----
ADDRCONF(NETDEV_UP): bond0: link is not ready
event_dev: bond0, event: 1
IFF_MASTER
event_dev: bond0, event: 8
IFF_MASTER
bond_ioctl: master=bond0, cmd=35216
slave_dev=cac5d800: 
slave_dev->name=eth1: 
eth1: ! NETIF_F_VLAN_CHALLENGED
event_dev: eth1, event: 8
eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1
event_dev: eth1, event: 1
event_dev: eth1, event: 8
IFF_SLAVE
Initial state of slave_dev is BOND_LINK_UP
bonding: bond0: enslaving eth1 as an active interface with an up link.
ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
event_dev: bond0, event: 4
IFF_MASTER
bond0: no IPv6 routers present

<<<<cable unplug>>>>

eth1: link down
event_dev: eth1, event: 4
IFF_SLAVE
bonding: bond0: link status definitely down for interface eth1, disabling it
event_dev: bond0, event: 4
IFF_MASTER

<<<<cable plug>>>>

eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1
event_dev: eth1, event: 4
IFF_SLAVE
bonding: bond0: link status definitely up for interface eth1.
bonding: bond0: making interface eth1 the new active one.
event_dev: eth1, event: 8
IFF_SLAVE
event_dev: eth1, event: 8
IFF_SLAVE
bonding: bond0: first active interface up!
event_dev: bond0, event: 4
IFF_MASTER
----

The current active slave is set by calling bond_select_active_slave() function
from bond_miimon_commit() function when the slave (eth1) link goes to state up.

I also tested this on other machine with Broadcom NetXtreme II BCM5708
1000Base-T NIC and there all works fine. The thing is that this adapter is down
and goes up after few seconds after it is enslaved.

This patch calls bond_select_active_slave() in bond_enslave() function for modes
alb and tlb and makes sure that the current active slave is set up properly even
when the slave state is already up. Tested on both systems, works fine.

Notice: The same problem can maybe also occrur in mode 8023AD but I'm unable to
test that.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Gianfar uses a hardware header FCB for offloading.  However when used
with bridging or IP forwarding, TX skb might not have enough headroom
for the FCB.  Reallocate skb for such cases.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch bumps the driver release date to March 25th 2009
and release version to 0.22.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the second PHY address which is strapped
to be at PHY address 3 instead of 2.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

wait_event_timeout just takes the numnber of jiffies to wait as
an argument. That value does not include jiffies itself.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a recovery is started for a qeth device, additional invocations
to change a mac address, to configure a VLAN interface on top, or to
add multicast addresses should wait till recovery is finished,
otherwise recovery might fail.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth: Unregister MAC addresses from device (layer 2) during
recovery cycle. When the device is set online the MAC
addresses are registered again on the device.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Performance measurements showed EDDP does not lower CPU costs but increase
them. So we dump out EDDP code from qeth driver.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add statistics counter for software tx checksumming.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of storing a private ->set_multicast_list, just
have a private netdev ops.
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement a way to provide the MAC address for ax88796 devices from
their platform data. Boards might decide to set the address
programmatically, taken from boot tags or other sources.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support to the ax88796 ethernet driver to take IRQ flags
given by the platform_device definition.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add device ID for a new variant of the 82574 adapter.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Acked-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ipv6 version of bind_conflict code calls ipv6_rcv_saddr_equal()
which at times wrongly identified intersections between addresses.
It particularly broke down under a few instances and caused erroneous
bind conflicts.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Binding to a v4-mapped address on an AF_INET6 socket should
produce the same result as binding to an IPv4 address on
AF_INET socket.  The two are interchangable as v4-mapped
address is really a portability aid.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The IPv4 wildcard (0.0.0.0) address does not intersect
in any way with explicit IPv6 addresses.  These two should
be permitted, but the IPv4 conflict code checks the ipv6only
bit as part of the test.  Since binding to an explicit IPv6
address restricts the socket to only that IPv6 address, the
side-effect is that the socket behaves as v6-only.  By
explicitely setting ipv6only in this case, allows the 2 binds
to succeed.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A socket marked v6-only, can not receive or send traffic to v4-mapped
addresses.  Thus allowing binding to v4-mapped address on such a
socket makes no sense.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hi, Pls accept this patch to cleanup rx/tx rate calculations as follows:
- check for jiffies wraparound
- remove typecast of a denominator
- do rate calculation only in workqueue context periodically
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the NETLINK_NO_ENOBUFS socket flag. This flag can
be used by unicast and broadcast listeners to avoid receiving
ENOBUFS errors.

Generally speaking, ENOBUFS errors are useful to notify two things
to the listener:

a) You may increase the receiver buffer size via setsockopt().
b) You have lost messages, you may be out of sync.

In some cases, ignoring ENOBUFS errors can be useful. For example:

a) nfnetlink_queue: this subsystem does not have any sort of resync
method and you can decide to ignore ENOBUFS once you have set a
given buffer size.

b) ctnetlink: you can use this together with the socket flag
NETLINK_BROADCAST_SEND_ERROR to stop getting ENOBUFS errors as
you do not need to resync (packets whose event are not delivered
are drop to provide reliable logging and state-synchronization).

Moreover, the use of NETLINK_NO_ENOBUFS also reduces a "go up, go down"
effect in terms of performance which is due to the netlink congestion
control when the listener cannot back off. The effect is the following:

1) throughput rate goes up and netlink messages are inserted in the
receiver buffer.
2) Then, netlink buffer fills and overruns (set on nlk->state bit 0).
3) While the listener empties the receiver buffer, netlink keeps
dropping messages. Thus, throughput goes dramatically down.
4) Then, once the listener has emptied the buffer (nlk->state
bit 0 is set off), goto step 1.

This effect is easy to trigger with netlink broadcast under heavy
load, and it is more noticeable when using a big receiver buffer.
You can find some results in [1] that show this problem.

[1] http://1984.lsi.us.es/linux/netlink/

This patch also includes the use of sk_drop to account the number of
netlink messages drop due to overrun. This value is shown in
/proc/net/netlink.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update myri10ge firmware headers to firmware version 1.4.41.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removed unused variable dev
Signed-off-by: vibi sreenivasan <vibi_sreenivasan@cms.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes two problems in the claw driver identified by
static code analysis:
o Change in case differentiation of received sense codes
o Use correct data length in claw hard_start_xmit routine
Signed-off-by: Andrew H. Richter <richtera@us.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

From: Ursula Braun <ursula.braun@de.ibm.com>

This patch fixes problems in the ctcm driver identified by
static code analysis:
o remove an unnecessary always true condition in ctcm_unpack_skb
o remove duplicate assignment in ctc_mpc_alloc_channel
o remove an unnecessary always true condition in ctcmpc_send_sweep_resp
o remove duplicate initialization in ctcmpc_unpack_skb
o shorten if condition in mpc_action_go_inop
o remove INOP event if mpc group is undefined in mpc_action_doxid7
Signed-off-by: Joel A. Fowler <fowlerja@us.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the receive code should tolerate any incoming garbage, it
should be protected against a potential wraparound when manipulating
length values within incoming data.
block_len is unsigned, so a too large subtraction will cause a
wraparound.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid kernel warning by using the correct hard_start_xmit return
code NETDEV_TX_BUSY for skb requeuing.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid kernel warnings by using the correct hard_start_xmit return
code NETDEV_TX_BUSY for skb requeuing.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid kernel warning by using the correct hard_start_xmit return
code NETDEV_TX_BUSY for skb requeuing.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lcs hard_start_xmit routine issued return codes other than
defined for this interface. Now lcs returns only either
NETDEV_TX_OK or NETDEV_TX_BUSY.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lcs uses low-level kernel_thread implementation.
All drivers should use <linux/kthread.h> API instead.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The tracing header needs to include definitions for the macros used and
the types referenced.  This lets automated tracing tools like SystemTap
make use of the tracepoint without any specific knowledge of its
meaning (leaving that to the user).
Signed-off-by: Josh Stone <jistone@redhat.com>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Arches without efficient unaligned access can still perform a loop
assuming 16bit alignment in ifname_compare()
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Supplements commit 67c0d579.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes following build error:

  CC      ucc_geth.o
ucc_geth.c: In function 'ucc_geth_probe':
ucc_geth.c:3644: error: implicit declaration of function 'uec_mdio_bus_name'
make[2]: *** [ucc_geth.o] Error 1
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We use RCU to defer freeing of conntrack structures. In DOS situation, RCU might
accumulate about 10.000 elements per CPU in its internal queues. To get accurate
conntrack counts (at the expense of slightly more RAM used), we might consider
conntrack counter not taking into account "about to be freed elements, waiting
in RCU queues". We thus decrement it in nf_conntrack_free(), not in the RCU
callback.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Tested-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>

I left a merge failure unresolved, noticed by Stephen
Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>