- 20 Dec, 2018 34 commits
-
-
YueHaibing authored
Fix a static code checker warning: drivers/net/ethernet/intel/e100.c:1349 e100_load_ucode_wait() warn: passing zero to 'PTR_ERR' Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Vinicius Costa Gomes authored
Add some pointers to the definition of the CBS algorithm, and some notes about the limits of its implementation in the i210 family of controllers. Signed-off-by:
Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by:
-
Jesus Sanchez-Palencia authored
Section 4.5.9 of the datasheet says that the total size of all packet buffers combined (TxPB 0 + 1 + 2 + 3 + RxPB + BMC2OS + OS2BMC) must not exceed 60KB. Today we are configuring a total of 62KB, so reduce the RxPB from 32KB to 30KB in order to respect that. The choice of changing RxPBSIZE here is mainly because it seems more correct to give more priority to the transmit packet buffers over the receiver ones when running in Qav mode. Also, the BMC2OS and OS2BMC sizes are already too short. Signed-off-by:
Jesus Sanchez-Palencia <jesus.s.palencia@gmail.com> Tested-by:
-
Jeff Kirsher authored
This change is based off of the work and suggestion of Jan Jablonsky <jan.jablonsky@thalesgroup.com>. The Watchdog workqueue in igb driver is scheduled every 2s for each network interface. That includes updating a statistics protected by spinlock. Function igb_update_stats in this case will be protected against preemption. According to number of a statistics registers (cca 60), processing this function might cause additional cpu load on CPU0. In case of statistics spinlock may be replaced with mutex, which reduce latency on CPU0. CC: Bernhard Kaindl <bernhard.kaindl@thalesgroup.com> CC: Jan Jablonsky <jan.jablonsky@thalesgroup.com> Signed-off-by:
-
David S. Miller authored
Michael Chan says: ==================== bnxt_en: Update for net-next. Three main changes in this series, besides the usual firmware spec update: 1. Add support for a new firmware communication channel direct to the firmware processor that handles flow offloads. This speeds up flow offload operations. 2. Use 64-bit internal flow handles to increase the number of flows that can be offloaded. 3. Add level-2 context memory paging so that we can configure more context memory for RDMA on the 57500 chips. Allocate more context memory if RDMA is enabled on the 57500 chips. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Michael Chan authored
For a little better performance on faster machines and faster link speeds. Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Venkat Duvvuru authored
Older firmware only supports 16-bit flow handle, because of which the number of flows that can be offloaded can’t scale beyond a point. Newer firmware supports 64-bit flow handle enabling the host to scale upto millions of flows. With the new 64-bit flow handle support, driver has to query flow stats in a different way compared to the older approach. This patch adds support for 64-bit flow handle and new way to query flow stats. Signed-off-by:
Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com> Reviewed-by:
Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com> Signed-off-by:
-
Michael Chan authored
If RDMA is supported on the 57500 chip, increase context memory allocations for the resources used by RDMA. Signed-off-by:
-
Michael Chan authored
Add the new functions bnxt_alloc_ctx_pg_tbls()/bnxt_free_ctx_pg_tbls() to allocate and free pages for context memory. The new functions will handle the different levels of paging support and allocate/free the pages accordingly using the existing functions. Signed-off-by:
-
Michael Chan authored
To support level 2 context page memory structures, enhance the bnxt_ring_mem_info structure with a "depth" field to specify the page level and add a flag to specify using full pages for L1 and L2 page tables. This is needed to support RDMA functionality on 57500 chips since RDMA requires more context memory. Signed-off-by:
-
Venkat Duvvuru authored
Earlier, some of the firmware commands (ex: CFA_FLOW_*) which are processed by KONG processor were sent to the CHIMP processor from the host. This approach was taken as there was no direct message channel to KONG. CHIMP in turn used to send them to KONG. Newer firmware supports a new message channel which the host can send messages directly to the KONG processor. This patch adds support for required changes needed in the driver to support direct KONG message channel. This speeds up flow related messages sent to the firmware for CLS_FLOWER offload. Signed-off-by:
-
Venkat Duvvuru authored
These routines will be enhanced in the subsequent patch to return the 2nd firmware comm. channel's hwrm response address & sequence id respectively. Signed-off-by:
-
Venkat Duvvuru authored
Typecast hwrm_cmd_resp_addr to (u8 *) from (void *) before doing arithmetic. Signed-off-by:
-
Venkat Duvvuru authored
In preparation for adding a 2nd communication channel to firmware. Signed-off-by:
-
Venkat Duvvuru authored
Set hwrm_intr_seq_id value to its inverted value instead of HWRM_SEQ_INVALID, when an hwrm completion of type CMPL_BASE_TYPE_HWRM_DONE is received. This will enable us to use the complete 16-bit sequence ID space. Signed-off-by:
-
Michael Chan authored
The major changes are in the flow offload firmware APIs. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-nextDavid S. Miller authored
Steffen Klassert says: ==================== pull request (net-next): ipsec-next 2018-12-20 Two last patches for this release cycle: 1) Remove an unused variable in xfrm_policy_lookup_bytype(). From YueHaibing. 2) Fix possible infinite loop in __xfrm6_tunnel_alloc_spi(). Also from YueHaibing. Please pull or let me know if there are problems. ==================== Signed-off-by: -
David Ahern authored
Add NDA_PROTOCOL to nda_policy and use the policy for attribute parsing and validation for adding neighbors and in dump requests. Remove the now duplicate checks on nla_len. Signed-off-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
David S. Miller authored
Peng Li says: ==================== net: hns3: code optimizations & bugfixes for HNS3 driver This patchset includes bugfixes and code optimizations for the HNS3 ethernet controller driver ==================== Signed-off-by: -
Peng Li authored
This patch removes the redundant variable initialization, as driver will devm_kzalloc to set value to hdev soon. Signed-off-by:
Peng Li <lipeng321@huawei.com> Signed-off-by:
-
Peng Li authored
Driver gets rss information from the last descriptor of the packet. When driver handle the rss type, ring->next_to_clean indicates the first descriptor of next packet. This patch fix the descriptor index with "ring->next_to_clean - 1". Fixes: 232fc64b ("net: hns3: Add HW RSS hash information to RX skb") Signed-off-by:
-
Jian Shen authored
When user disables flow director, all the rules will be disabled. But when reset happens, it will restore all the rules again. It's not reasonable. This patch fixes it by add flow director status check before restore fules. Fixes: 6871af29 ("net: hns3: Add reset handle for flow director") Fixes: c17852a8 ("net: hns3: Add support for enable/disable flow director") Signed-off-by:
Jian Shen <shenjian15@huawei.com> Signed-off-by:
-
Jian Shen authored
When add flow director fule for vf, the vf id is used as array subscript before valid checking, which may cause memory overflow. Fixes: dd74f815 ("net: hns3: Add support for rule add/delete for flow director") Signed-off-by:
-
Huazhong Tan authored
While doing DOWN operation, the driver will reclaim the memory which has already used for TX. If the hardware is processing this memory, it will cause a RCB error to the hardware. According the hardware's description, the driver should reset the tqp before reclaim the memory during DOWN. Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
-
Jian Shen authored
Each pf supports max 64 vectors and 128 tqps. For 2p/4p core scenario, there may be more than 64 cpus online. So the result of min_t(u16, num_Online_cpus(), tqp_num) may be more than 64. This patch adds check for the vector number. Fixes: dd38c726 ("net: hns3: fix for coalesce configuration lost during reset") Signed-off-by:
-
Peng Li authored
udelay() in driver may always occupancy processor. If there is only one cpu in system, the VF driver may initialize fail when insmod PF and VF driver in the same system. This patch use msleep() to free cpu when VF wait PF message. Signed-off-by:
-
Jian Shen authored
In original codes, default tc value is set to the max tc. It's more reasonable to close tc by changing default tc value to 1. Users can enable it with lldp tool when they want to use tc. Signed-off-by:
-
Jian Shen authored
When triggering nic down, there is a time window between bringing down the protocol stack and stopping the work task. If the net is up in the time window, it may bring up the protocol stack again. This patch fixes it by stop the work task at the beginning of hns3_nic_net_stop(). To keep symmetrical, start the work task at the end of hns3_nic_net_open(). Signed-off-by:
-
David Ahern authored
pneigh_lookup uses kmalloc versus kzalloc when new entries are allocated. Given that the newly added protocol field needs to be initialized. Fixes: df9b0e30 ("neighbor: Add protocol attribute") Signed-off-by:
-
Peter Oskolkov authored
This patch refactors reuseport_add_any selftest a bit: - makes it more modular (eliminates several copy/pasted blocks); - skips DCCP tests if DCCP is not supported V2: added "Signed-off-by" tag. Signed-off-by:
Peter Oskolkov <posk@google.com> Signed-off-by:
-
Andrew Lunn authored
The 6320 family of switches uses the same watchdog registers as the 6390. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by:
-
David S. Miller authored
Biao Huang says: ==================== add ethernet binding and modify ethernet driver for mt2712 changes in v3: resend this series base on the latest net-next tree. changes in v2 as comments from Sean: 1. fix typo. 2. use capital letters for RMII/MII/RGMII in driver and bindings. v1: This new series is the result of discussion in: http://lkml.org/lkml/2018/12/13/1007 http://lkml.org/lkml/2018/12/14/53 1. ethernet binding file move to this series. 2. remove fine tune property in device tree 3. remove fine tune flow in ethernet driver 4. set rgmii timing according to the value in device tree, and don't care whether phy insert internal delay or not. ==================== Signed-off-by:
-
Biao Huang authored
1. remove fine-tune property and related setting to simplify the timing adjustment flow. 2. set timing value according to the value from device tree, and will not care whether PHY insert internal delay. Signed-off-by:
Biao Huang <biao.huang@mediatek.com> Signed-off-by:
-
Biao Huang authored
remove fine-tune property in device tree, modify the corresponding description in dt-binding. Signed-off-by:
-
- 19 Dec, 2018 6 commits
-
-
David S. Miller authored
Roopa Prabhu says: ==================== neigh get support This series adds support for neigh get similar to route and recently added fdb get. v2: fix key len check. and some other fixes ==================== Signed-off-by: -
Roopa Prabhu authored
Signed-off-by:
Roopa Prabhu <roopa@cumulusnetworks.com> Reviewed-by:
David Ahern <dsa@cumulusnetworks.com> Signed-off-by:
-
Roopa Prabhu authored
this patch registers neigh doit handler. The doit handler returns a neigh entry given dst and dev. This is similar to route and fdb doit (get) handlers. Also moves nda_policy declaration from rtnetlink.c to neighbour.c Signed-off-by:
-
David S. Miller authored
Ido Schimmel says: ==================== mlxsw: Make driver more robust In recent months we fixed several bugs in the driver that could have been avoided by re-evaluating some of the involved code paths and by introducing relevant and comprehensive test cases. This patchset tries to do that by introducing a set of small and mostly non-functional changes in addition to a new test. I have further improvements in mind, but they can be done in a different set. Patch #1 makes sure we correctly sanitize upper devices of a VLAN interface. Patch #2 removes an unexpected behavior from the driver, in which routes configured on a VLAN interface will cease being offloaded after certain operations. Patch #3 is a small cleanup. Patch #4 simplifies the driver by removing reference counting from VLAN entries configured on a port. Patches #5-#6 simplify linking/unlinking from a bridge, especially when LAG and VLAN devices are involved. They make both operations symmetric even when ports are unlinked from a bridged LAG device. Patch #7-#9 make router interface (RIF) deletion more robust by removing reliance on device chain to indicate whether a NETDEV_DOWN event in the inet{,6}addr notification chains should be processed. This is due to the fact that IP addresses can be flushed from a netdev after it was unlinked from its lower device. Patch #10 adds a new test to for valid and invalid configurations over mlxsw ports. Some of the test cases are derived from recent fixes. I expect that more test cases will be added over time. ==================== Signed-off-by: -
Ido Schimmel authored
Add a new test that is focused on rtnetlink configuration. Its purpose is to test valid and invalid (as deemed by mlxsw) configurations and make sure that they succeed / fail without producing a trace. Some of the test cases are derived from recent fixes in order to make sure that the fixed bugs are not introduced again. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Reviewed-by:
Petr Machata <petrm@mellanox.com> Signed-off-by:
-
Ido Schimmel authored
Previous patches tried to make RIF deletion more robust and avoid use-after-free situations. As another precaution, hold a reference on a RIF's netdev and release it when the RIF is deleted. Signed-off-by:
-
