Extend erase timeout in M25P80 SPI Flash driver.

The M25P80 drivers fails erasing sectors on a M25P128 because the ready
wait timeout is too short. Change the timeout from a simple loop count to a
suitable number of seconds.
Signed-off-by: Peter Horton <zero@colonel-panic.org>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

There is a logic error in "whole chip erase" for the m25p80 family.  If
the whole device is successfully erased, erase_chip() will return 0, and
the code will fall through to the "else" clause, and do sector-by-sector
erase in addition to the whole-chip erase.  This patch corrects that.

Also, the MAX_READY_WAIT_COUNT is insufficient for an m25p16 connected
to a 400 MHz powerpc.  Increasing it allows me to successfully program
the device on my board.
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

MTD has got sysfs support in 2.6.30-rc1. But subpage size is not
exposed there - do this.

UBI utilities badly need this parameter. At the moment there is
no way to get subpage size - ioctls do not return it. And we
just got sysfs support, so we can easilly extend it with this
additional parameter.

This can be merged late in the development cycle because:
1. sysfs support has been just added - there are no users for
   it so far, even.
2. UBI utilities really need this parameter, and it is better
   not to delay this.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

drivers/mtd/mtdcore.c: In function 'mtd_release':
drivers/mtd/mtdcore.c:51: warning: unused variable 'mtd'

[akpm: make it actually build]
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
  drm/i915: fix scheduling while holding the new active list spinlock
  drm/i915: Allow tiling of objects with bit 17 swizzling by the CPU.
  drm/i915: Correctly set the write flag for get_user_pages in pread.
  drm/i915: Fix use of uninitialized var in 40a5f0de
  drm/i915: indicate framebuffer restore key in SysRq help message
  drm/i915: sync hdmi detection by hdmi identifier with 2D
  drm/i915: Fix a mismerge of the IGD patch (new .find_pll hooks missed)
  drm/i915: Implement batch and ring buffer dumping

Revert part of af5c820a ("x86: cpumask:
use work_on_cpu in arch/x86/kernel/microcode_core.c")

That change is causing only one Intel CPU's microcode to be updated e.g.
microcode: CPU3 updated from revision 0x9 to 0x17, date = 2005-04-22
where before it announced that also for CPU0 and CPU1 and CPU2.

We cannot use work_on_cpu() in the CONFIG_MICROCODE_OLD_INTERFACE code,
because Intel's request_microcode_user() involves a copy_from_user() from
/sbin/microcode_ctl, which therefore needs to be on that CPU at the time.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

regression caused by commit 5e118f41:
i915_gem_object_move_to_inactive() should be called in task context,
as it calls fput();

Signed-off-by: Shaohua Li<shaohua.li@intel.com>
[anholt: Add more detail to the comment about the lock break that's added]
Signed-off-by: Eric Anholt <eric@anholt.net>

Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  lockdep: warn about lockdep disabling after kernel taint, fix

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: fix "direct_io" private mmap
  fuse: fix argument type in fuse_get_user_pages()

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
  nilfs2: fix possible mismatch of sufile counters on recovery
  nilfs2: segment usage file cleanups
  nilfs2: fix wrong accounting and duplicate brelse in nilfs_sufile_set_error
  nilfs2: simplify handling of active state of segments fix
  nilfs2: remove module version
  nilfs2: fix lockdep recursive locking warning on meta data files
  nilfs2: fix lockdep recursive locking warning on bmap
  nilfs2: return f_fsid for statfs2

* 'fixes-for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Add missing FILE tag to MAINTAINERS
  microblaze: remove duplicated #include's
  microblaze: struct device - replace bus_id with dev_name()
  microblaze: Simplify copy_thread()
  microblaze: Add TIMESTAMPING constants to socket.h
  microblaze: Add missing empty ftrace.h file
  microblaze: Fix problem with removing zero length files

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: Add in PCI bus for DMA API debugging.
  sh: Pre-allocate a reasonable number of DMA debug entries.
  sh: sh7786: modify usb setup timeout judgment bug.
  MAINTAINERS: Update sh architecture file patterns.
  sh: ap325: use edge control for ov772x camera
  sh: Plug in support for ARCH=sh64 using sh SRCARCH.
  sh: urquell: Fix up address mapping in board comments.
  sh: Add support for DMA API debugging.
  sh: Provide cpumask_of_pcibus() to fix NUMA build.
  sh: urquell: Add board comment
  sh: wire up sys_preadv/sys_pwritev() syscalls.
  sh: sh7785lcr: fix PCI address map for 32-bit mode
  sh: intc: Added resume from hibernation support to the intc

Fix lpfc_parse_bg_err()'s use of do_div().  It should be passing a 64-bit
variable as the first parameter.  However, since it's only using a 32-bit
variable, it doesn't need to use do_div() at all, but can instead use the
division operator.

This deals with the following warnings:

    CC      drivers/scsi/lpfc/lpfc_scsi.o
  drivers/scsi/lpfc/lpfc_scsi.c: In function 'lpfc_parse_bg_err':
  drivers/scsi/lpfc/lpfc_scsi.c:1397: warning: comparison of distinct pointer types lacks a cast
  drivers/scsi/lpfc/lpfc_scsi.c:1397: warning: right shift count >= width of type
  drivers/scsi/lpfc/lpfc_scsi.c:1397: warning: passing argument 1 of '__div64_32' from incompatible pointer type
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Updates some usb_serial_port members documentation.
Signed-off-by: Leandro Dorileo <ldorileo@gmail.com>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In commit 51dcdfec ("parport: Use the
PCI IRQ if offered") parport_pc_probe_port() gained an irqflags arg.
This isn't being supplied on powerpc.  This patch make powerpc fallback
to the old behaviour, that is using "0" for irqflags.

Fixes build failure:

  In file included from drivers/parport/parport_pc.c:68:
  arch/powerpc/include/asm/parport.h: In function 'parport_pc_find_nonpci_ports':
  arch/powerpc/include/asm/parport.h:32: error: too few arguments to function 'parport_pc_probe_port'
  arch/powerpc/include/asm/parport.h:32: error: too few arguments to function 'parport_pc_probe_port'
  arch/powerpc/include/asm/parport.h:32: error: too few arguments to function 'parport_pc_probe_port'
  make[3]: *** [drivers/parport/parport_pc.o] Error 1
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

These got overlooked first time around.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If the ti-usb adapter returns an zero data length frame (which happens)
then we leak a kref.  Found by Christoph Mair <christoph.mair@gmail.com>
who proposed a patch.  The patch here is different as Christoph's patch
didn't work for the case where tty = NULL and data arrived but Christoph
did all the hard work chasing it down.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ACM sets the low latency flag but calls the flip buffer routines from
IRQ context which isn't permitted (and as of 2.6.29 causes a warning
hence this one was caught)

Fortunatelt ACM doesn't need to set this flag in the first place as it
only set it to work around problems in ancient (pre tty flip rewrite)
kernels.
Reported-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Michal Simek <monstr@monstr.eu>

Impact: build fix for Sparc and s390

Stephen Rothwell reported that the Sparc build broke:

 In file included from kernel/panic.c:12:
 include/linux/debug_locks.h: In function '__debug_locks_off':
 include/linux/debug_locks.h:15: error: implicit declaration of function 'xchg'

due to:

 9eeba613: lockdep: warn about lockdep disabling after kernel taint

There is some inconsistency between architectures about where exactly
xchg() is defined.

The traditional place is in system.h but the more logical point for it
is in atomic.h - where most architectures (especially new ones) have
it defined. These architecture also still offer it via system.h.

Some, such as Sparc or s390 only have it in asm/system.h and not available
via asm/atomic.h at all.

Use the widest set of headers in debug_locks.h and also include asm/system.h.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20090414144317.026498df.sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Remove duplicated #include's in
  arch/microblaze/include/asm/io.h
  arch/microblaze/kernel/prom.c
  arch/microblaze/kernel/ptrace.c
  arch/microblaze/kernel/signal.c
  arch/microblaze/kernel/sys_microblaze.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>

Signed-off-by: Michal Simek <monstr@monstr.eu>

Removing nr parameter from copy_tread function
commit 6f2c55b8Signed-off-by: Michal Simek <monstr@monstr.eu>

This changes was introduce with
commit: cb9eff09

net: new user space API for time stamping of incoming and outgoing packets
Signed-off-by: Michal Simek <monstr@monstr.eu>

Signed-off-by: Michal Simek <monstr@monstr.eu>

Adding one new line was recommended solution.
Test with make distclean
Tested-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>

This adds in the pci_bus_type for DMA API debug.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This prevents the DMA API debugging from running out of entries right
away on boot. Defines 4096 entries by default, which while a bit on the
heavy side, ought to leave enough breathing room for some time.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  tomoyo: version bump to 2.2.0.
  tomoyo: add Documentation/tomoyo.txt

We ended up incorrectly using '&cur' instead of '&readin' in the
work_on_cpu() -> smp_call_function_single() transformation in commit
01599fca ("cpufreq: use
smp_call_function_[single|many]() in acpi-cpufreq.c").

Andrew explains:
 "OK, the acpi tree went and had conflicting changes merged into it after
  I'd written the patch and it appears that I incorrectly reverted part
  of 18b2646f while fixing the resulting
  rejects.

  Switching it to `readin' looks correct."
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Kentaro Takeda <takedakn@nttdata.co.jp>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Toshiharu Harada <haradats@nttdata.co.jp>
Signed-off-by: James Morris <jmorris@namei.org>

Signed-off-by: Kentaro Takeda <takedakn@nttdata.co.jp>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Toshiharu Harada <haradats@nttdata.co.jp>
Signed-off-by: James Morris <jmorris@namei.org>

* 'for-rc1/xen/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
  xen: add FIX_TEXT_POKE to fixmap
  xen: honour VCPU availability on boot
  xen: clean up gate trap/interrupt constants
  xen: set _PAGE_NX in __supported_pte_mask before pagetable construction
  xen: resume interrupts before system devices.
  xen/mmu: weaken flush_tlb_other test
  xen/mmu: some early pagetable cleanups
  Xen: Add virt_to_pfn helper function
  x86-64: remove PGE from must-have feature list
  xen: mask XSAVE from cpuid
  NULL noise: arch/x86/xen/smp.c
  xen: remove xen_load_gdt debug
  xen: make xen_load_gdt simpler
  xen: clean up xen_load_gdt
  xen: split construction of p2m mfn tables from registration
  xen: separate p2m allocation from setting
  xen: disable preempt for leave_lazy_mmu

This corrects a race with the PHY RST bit not being set properly if the
PLL status changes right before timeout. This resulted in it potentially
failing even if the device came up in time.

Special thanks to Mr. Juha Leppanen and Iwamatsu-san for reporting this
out and reviewing it.
Reported-by: Juha Leppanen <juha_motorsportcom@luukku.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Tested-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The edac-core driver includes code which assumes that the work_struct
which is included in every delayed_work is the first member of that
structure.  This is currently the case but might change in the future, so
use to_delayed_work() instead, which doesn't make such an assumption.

linux-2.6.30-rc1 has the to_delayed_work() function that will allow this
patch to work
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix the edac local pci_write_bits32 to properly note the 'escape' mask if
all ones in a 32-bit word.

Currently no consumer of this function uses that mask, so there is no
danger to existing code.
Signed-off-by: Jeff Haran <jharan@Brocade.COM>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Introduce xpc_arch_ops and eliminate numerous individual global definitions.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Dean Nelson <dcn@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgi-xpc has a window of failure where an open message can be sent and a
subsequent data message can get lost.  We have added a new message
(opencomplete) which closes that window.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The heartbeat timeout functionality in sgi-xpc is currently not trained to
the connection time.  If a connection is made and the code is in the last
polling window prior to doing a timeout, the next polling window will see
the heartbeat as unchanged and initiate a no-heartbeat disconnect.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>