Process small blocks using the fallback cipher, as a workaround for an
observed failure (DMA-related, apparently) when computing the GCM ghash
key.  This brings a speed gain as well, since it avoids the latency of
using the hardware engine to process small blocks.

Using software for all 16-byte requests would be enough to make GCM
work, but to increase performance, a larger threshold would be better.
Measuring the performance of supported ciphers with openssl speed,
software matches hardware at around 768-1024 bytes.

Considering the 256-bit ciphers, software is 2-3 times faster than qce
at 256-bytes, 30% faster at 512, and about even at 768-bytes.  With
128-bit keys, the break-even point would be around 1024-bytes.

This adds the 'aes_sw_max_len' parameter, to set the largest request
length processed by the software fallback.  Its default is being set to
512 bytes, a little lower than the break-even point, to balance the cost
in CPU usage.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The qce crypto driver appends an extra entry to the dst sgl, to maintain
private state information.

When the gcm driver sends requests to the ctr skcipher, it passes the
authentication tag after the actual crypto payload, but it must not be
touched.

Commit 1336c2221bee ("crypto: qce - save a sg table slot for result
buf") limited the destination sgl to avoid overwriting the
authentication tag but it assumed the tag would be in a separate sgl
entry.

This is not always the case, so it is better to limit the length of the
destination buffer to req->cryptlen before appending the result buf.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Function dev_err() after platform_get_irq() is redundant because
platform_get_irq() already prints an error.
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

No logs are recorded in dmesg during chcr module load, hence
adding the print and also appending -ko to driver version.
Signed-off-by: Devulapally Shiva Krishna <shiva@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

When running tcrypt skcipher speed tests, logs contain things like:
testing speed of async ecb(des3_ede) (ecb(des3_ede-generic)) encryption
or:
testing speed of async ecb(aes) (ecb(aes-ce)) encryption

The algorithm implementations are sync, not async.
Fix this inaccuracy.

Fixes: 7166e589 ("crypto: tcrypt - Use skcipher")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The path with the CRYPTO_ALG_LARVAL flag has jumped to the end before
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The libkcapi test which causes kernel panic is
aead asynchronous vmsplice multiple test.

./bin/kcapi  -v -d 4 -x 10   -c "ccm(aes)"
-q 4edb58e8d5eb6bc711c43a6f3693daebde2e5524f1b55297abb29f003236e43d
-t a7877c99 -n 674742abd0f5ba -k 2861fd0253705d7875c95ba8a53171b4
-a fb7bc304a3909e66e2e0c5ef952712dd884ce3e7324171369f2c5db1adc48c7d

This patch avoids dma_mapping of a zero length sg which causes the panic,
by using sg_nents_for_len which maps only upto a specific length
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The libkcapi "cbc(aes)" failed tests are
symmetric asynchronous cipher one shot multiple test,
symmetric asynchronous cipher stream multiple test,
Symmetric asynchronous cipher vmsplice multiple test

In this patch a wait_for_completion is added in the chcr_aes_encrypt function,
which completes when the response of comes from the hardware.
This adds serialization for encryption in cbc(aes) aio case.
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Add arch/arm64/crypto/poly1305-core.S to .gitignore
as it's built from poly1305-core.S_shipped

Fixes: f569ca16 ("crypto: arm64/poly1305 - incorporate OpenSSL/CRYPTOGAMS NEON implementation")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/crypto/ccree/cc_cipher.c: In function 'cc_setup_state_desc':
drivers/crypto/ccree/cc_cipher.c:536:15: warning:
 variable 'du_size' set but not used [-Wunused-but-set-variable]

commit 5c83e8ec ("crypto: ccree - fix FDE descriptor sequence")
involved this unused variable, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Remove the auth tag size from cryptlen before mapping the destination
in out-of-place AEAD decryption thus resolving a crash with
extended testmgr tests.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org # v4.19+
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Add reference counter incremented for each frame enqueued in CAAM
and replace unconditional sleep in empty_caam_fq() with polling the
reference counter.

When CONFIG_CRYPTO_MANAGER_EXTRA_TESTS=y boot time on LS1043A
platform with this optimization decreases from ~1100s to ~11s.
Signed-off-by: Valentin Ciocoi Radulescu <valentin.ciocoi@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Fix an error causing no block sizes to be reported during
all AEAD registrations.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

OFB and CTR modes block sizes were wrongfully reported as
the underlying block sizes. Fix it to 1 bytes as they
turn the block ciphers into stream ciphers.

Also document why our XTS differes from the generic
implementation.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Make sure to only add the size of the auth tag to the source mapping
for encryption if it is an in-place operation. Failing to do this
previously caused us to try and map auth size len bytes from a NULL
mapping and crashing if both the cryptlen and assoclen are zero.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Deal gracefully with a NULL or empty scatterlist which can happen
if both cryptlen and assoclen are zero and we're doing in-place
AEAD encryption.

This fixes a crash when this causes us to try and map a NULL page,
at least with some platforms / DMA mapping configs.

Cc: stable@vger.kernel.org # v4.19+
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This comes from INRIA's HACL*/Vale. It implements the same algorithm and
implementation strategy as the code it replaces, only this code has been
formally verified, sans the base point multiplication, which uses code
similar to prior, only it uses the formally verified field arithmetic
alongside reproducable ladder generation steps. This doesn't have a
pure-bmi2 version, which means haswell no longer benefits, but the
increased (doubled) code complexity is not worth it for a single
generation of chips that's already old.

Performance-wise, this is around 1% slower on older microarchitectures,
and slightly faster on newer microarchitectures, mainly 10nm ones or
backports of 10nm to 14nm. This implementation is "everest" below:

Xeon E5-2680 v4 (Broadwell)

     armfazh: 133340 cycles per call
     everest: 133436 cycles per call

Xeon Gold 5120 (Sky Lake Server)

     armfazh: 112636 cycles per call
     everest: 113906 cycles per call

Core i5-6300U (Sky Lake Client)

     armfazh: 116810 cycles per call
     everest: 117916 cycles per call

Core i7-7600U (Kaby Lake)

     armfazh: 119523 cycles per call
     everest: 119040 cycles per call

Core i7-8750H (Coffee Lake)

     armfazh: 113914 cycles per call
     everest: 113650 cycles per call

Core i9-9880H (Coffee Lake Refresh)

     armfazh: 112616 cycles per call
     everest: 114082 cycles per call

Core i3-8121U (Cannon Lake)

     armfazh: 113202 cycles per call
     everest: 111382 cycles per call

Core i7-8265U (Whiskey Lake)

     armfazh: 127307 cycles per call
     everest: 127697 cycles per call

Core i7-8550U (Kaby Lake Refresh)

     armfazh: 127522 cycles per call
     everest: 127083 cycles per call

Xeon Platinum 8275CL (Cascade Lake)

     armfazh: 114380 cycles per call
     everest: 114656 cycles per call

Achieving these kind of results with formally verified code is quite
remarkable, especialy considering that performance is favorable for
newer chips.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

We need to decrement this refcounter on these error paths.

Fixes: f7d76e05 ("crypto: user - fix use_after_free of struct xxx_request")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

If all possible errors occurs at the same time, the error_status will be
all 1s. The doorbell timeout error and FIFO overflow error will be print
in each cycle, which should be print just once.
Signed-off-by: Shukun Tan <tanshukun1@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

In error detect process, a lot of duplicate code can put into qm. We add
two callback(get_dev_hw_err_status and log_dev_hw_err) into struct
hisi_qm_err_ini to handle device error detect, meanwhile the qm error
detect not changed.
Signed-off-by: Shukun Tan <tanshukun1@huawei.com>
Signed-off-by: Zaibo Xu <xuzaibo@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Configure zip RAS error type in error handle initialization,
Where ECC 1bit is configured as CE error, others are NFE.
Signed-off-by: Shukun Tan <tanshukun1@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The initialization and uninitialization of zip/hpre/sec/qm hardware error
is processed in respective drivers, which could be unified into qm.c. We
add struct hisi_qm_err_ini into struct hisi_qm, which involve all error
handlers of device and assignment should be done in driver probe.
Signed-off-by: Shukun Tan <tanshukun1@huawei.com>
Signed-off-by: Zaibo Xu <xuzaibo@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Pull more Kbuild updates from Masahiro Yamada:

 - fix randconfig to generate a sane .config

 - rename hostprogs-y / always to hostprogs / always-y, which are more
   natual syntax.

 - optimize scripts/kallsyms

 - fix yes2modconfig and mod2yesconfig

 - make multiple directory targets ('make foo/ bar/') work

* tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: make multiple directory targets work
  kconfig: Invalidate all symbols after changing to y or m.
  kallsyms: fix type of kallsyms_token_table[]
  scripts/kallsyms: change table to store (strcut sym_entry *)
  scripts/kallsyms: rename local variables in read_symbol()
  kbuild: rename hostprogs-y/always to hostprogs/always-y
  kbuild: fix the document to use extra-y for vmlinux.lds
  kconfig: fix broken dependency in randconfig-generated .config

Pull new zonefs file system from Damien Le Moal:
 "Zonefs is a very simple file system exposing each zone of a zoned
  block device as a file.

  Unlike a regular file system with native zoned block device support
  (e.g. f2fs or the on-going btrfs effort), zonefs does not hide the
  sequential write constraint of zoned block devices to the user. As a
  result, zonefs is not a POSIX compliant file system. Its goal is to
  simplify the implementation of zoned block devices support in
  applications by replacing raw block device file accesses with a richer
  file based API, avoiding relying on direct block device file ioctls
  which may be more obscure to developers.

  One example of this approach is the implementation of LSM
  (log-structured merge) tree structures (such as used in RocksDB and
  LevelDB) on zoned block devices by allowing SSTables to be stored in a
  zone file similarly to a regular file system rather than as a range of
  sectors of a zoned device. The introduction of the higher level
  construct "one file is one zone" can help reducing the amount of
  changes needed in the application while at the same time allowing the
  use of zoned block devices with various programming languages other
  than C.

  Zonefs IO management implementation uses the new iomap generic code.
  Zonefs has been successfully tested using a functional test suite
  (available with zonefs userland format tool on github) and a prototype
  implementation of LevelDB on top of zonefs"

* tag 'zonefs-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
  zonefs: Add documentation
  fs: New zonefs file system

In order to allow the GICv4 code to link properly on 32bit ARM,
make sure we don't use 64bit divisions when it isn't strictly
necessary.

Fixes: 4e6437f1 ("irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull cifs fixes from Steve French:
 "13 cifs/smb3 patches, most from testing at the SMB3 plugfest this week:

   - Important fix for multichannel and for modefromsid mounts.

   - Two reconnect fixes

   - Addition of SMB3 change notify support

   - Backup tools fix

   - A few additional minor debug improvements (tracepoints and
     additional logging found useful during testing this week)"

* tag '5.6-rc-smb3-plugfest-patches' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: Add defines for new information level, FileIdInformation
  smb3: print warning once if posix context returned on open
  smb3: add one more dynamic tracepoint missing from strict fsync path
  cifs: fix mode bits from dir listing when mounted with modefromsid
  cifs: fix channel signing
  cifs: add SMB3 change notification support
  cifs: make multichannel warning more visible
  cifs: fix soft mounts hanging in the reconnect code
  cifs: Add tracepoints for errors on flush or fsync
  cifs: log warning message (once) if out of disk space
  cifs: fail i/o on soft mounts if sessionsetup errors out
  smb3: fix problem with null cifs super block with previous patch
  SMB3: Backup intent flag missing from some more ops

Pull vboxfs from Al Viro:
 "This is the VirtualBox guest shared folder support by Hans de Goede,
  with fixups for fs_parse folded in to avoid bisection hazards from
  those API changes..."

* 'work.vboxsf' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: Add VirtualBox guest shared folder (vboxsf) support

Pull x86 fixes from Thomas Gleixner:
 "A set of fixes for X86:

   - Ensure that the PIT is set up when the local APIC is disable or
     configured in legacy mode. This is caused by an ordering issue
     introduced in the recent changes which skip PIT initialization when
     the TSC and APIC frequencies are already known.

   - Handle malformed SRAT tables during early ACPI parsing which caused
     an infinite loop anda boot hang.

   - Fix a long standing race in the affinity setting code which affects
     PCI devices with non-maskable MSI interrupts. The problem is caused
     by the non-atomic writes of the MSI address (destination APIC id)
     and data (vector) fields which the device uses to construct the MSI
     message. The non-atomic writes are mandated by PCI.

     If both fields change and the device raises an interrupt after
     writing address and before writing data, then the MSI block
     constructs a inconsistent message which causes interrupts to be
     lost and subsequent malfunction of the device.

     The fix is to redirect the interrupt to the new vector on the
     current CPU first and then switch it over to the new target CPU.
     This allows to observe an eventually raised interrupt in the
     transitional stage (old CPU, new vector) to be observed in the APIC
     IRR and retriggered on the new target CPU and the new vector.

     The potential spurious interrupts caused by this are harmless and
     can in the worst case expose a buggy driver (all handlers have to
     be able to deal with spurious interrupts as they can and do happen
     for various reasons).

   - Add the missing suspend/resume mechanism for the HYPERV hypercall
     page which prevents resume hibernation on HYPERV guests. This
     change got lost before the merge window.

   - Mask the IOAPIC before disabling the local APIC to prevent
     potentially stale IOAPIC remote IRR bits which cause stale
     interrupt lines after resume"

* tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/apic: Mask IOAPIC entries when disabling the local APIC
  x86/hyperv: Suspend/resume the hypercall page for hibernation
  x86/apic/msi: Plug non-maskable MSI affinity race
  x86/boot: Handle malformed SRAT tables during early ACPI parsing
  x86/timer: Don't skip PIT setup when APIC is disabled or in legacy mode

Pull SMP fixes from Thomas Gleixner:
 "Two fixes for the SMP related functionality:

   - Make the UP version of smp_call_function_single() match SMP
     semantics when called for a not available CPU. Instead of emitting
     a warning and assuming that the function call target is CPU0,
     return a proper error code like the SMP version does.

   - Remove a superfluous check in smp_call_function_many_cond()"

* tag 'smp-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  smp/up: Make smp_call_function_single() match SMP semantics
  smp: Remove superfluous cond_func check in smp_call_function_many_cond()

Pull perf fixes from Thomas Gleixner:
 "A set of fixes and improvements for the perf subsystem:

  Kernel fixes:

   - Install cgroup events to the correct CPU context to prevent a
     potential list double add

   - Prevent an integer underflow in the perf mlock accounting

   - Add a missing prototype for arch_perf_update_userpage()

  Tooling:

   - Add a missing unlock in the error path of maps__insert() in perf
     maps.

   - Fix the build with the latest libbfd

   - Fix the perf parser so it does not delete parse event terms, which
     caused a regression for using perf with the ARM CoreSight as the
     sink configuration was missing due to the deletion.

   - Fix the double free in the perf CPU map merging test case

   - Add the missing ustring support for the perf probe command"

* tag 'perf-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf maps: Add missing unlock to maps__insert() error case
  perf probe: Add ustring support for perf probe command
  perf: Make perf able to build with latest libbfd
  perf test: Fix test case Merge cpu map
  perf parse: Copy string to perf_evsel_config_term
  perf parse: Refactor 'struct perf_evsel_config_term'
  kernel/events: Add a missing prototype for arch_perf_update_userpage()
  perf/cgroups: Install cgroup events to correct cpuctx
  perf/core: Fix mlock accounting in perf_mmap()

Pull timer fixes from Thomas Gleixner:
 "Two small fixes for the time(r) subsystem:

   - Handle a subtle race between the clocksource watchdog and a
     concurrent clocksource watchdog stop/start sequence correctly to
     prevent a timer double add bug.

   - Fix the file path for the core time namespace file"

* tag 'timers-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource: Prevent double add_timer_on() for watchdog_timer
  MAINTAINERS: Correct path to time namespace source file

Pull interrupt fixes from Thomas Gleixner:
 "A set of fixes for the interrupt subsystem:

   - Provision only ACPI enabled redistributors on GICv3

   - Use the proper command colums when building the INVALL command for
     the GICv3-ITS

   - Ensure the allocation of the L2 vPE table for GICv4.1

   - Correct the GICv4.1 VPROBASER programming so it uses the proper
     size

   - A set of small GICv4.1 tidy up patches

   - Configuration cleanup for C-SKY interrupt chip

   - Clarify the function documentation for irq_set_wake() to document
     that the wakeup functionality is orthogonal to the irq
     disable/enable mechanism"

* tag 'irq-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/gic-v3-its: Rename VPENDBASER/VPROPBASER accessors
  irqchip/gic-v3-its: Remove superfluous WARN_ON
  irqchip/gic-v4.1: Drop 'tmp' in inherit_vpe_l1_table_from_rd()
  irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level
  irqchip/gic-v4.1: Set vpe_l1_base for all redistributors
  irqchip/gic-v4.1: Fix programming of GICR_VPROPBASER_4_1_SIZE
  genirq: Clarify that irq wake state is orthogonal to enable/disable
  irqchip/gic-v3-its: Reference to its_invall_cmd descriptor when building INVALL
  irqchip: Some Kconfig cleanup for C-SKY
  irqchip/gic-v3: Only provision redistributors that are enabled in ACPI

Pull EFI fix from Thomas Gleixner:
 "A single fix for a EFI boot regression on X86 which was caused by the
  recent rework of the EFI memory map parsing. On systems with invalid
  memmap entries the cleanup function uses an value which cannot be
  relied on in this stage. Use the actual EFI memmap entry instead"

* tag 'efi-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi/x86: Fix boot regression on systems with invalid memmap entries

Pull misc SCSI fixes from James Bottomley:
 "Five small patches, all in drivers or doc, which missed the initial
  pull request.

  The qla2xxx and megaraid_sas are actual fixes and the rest are
  spelling and doc changes"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ufs: fix spelling mistake "initilized" -> "initialized"
  scsi: pm80xx: fix spelling mistake "to" -> "too"
  scsi: MAINTAINERS: ufs: remove pedrom.sousa@synopsys.com
  scsi: megaraid_sas: fixup MSIx interrupt setup during resume
  scsi: qla2xxx: Fix unbound NVME response length

Pull networking fixes from David Miller:

 1) Unbalanced locking in mwifiex_process_country_ie, from Brian Norris.

 2) Fix thermal zone registration in iwlwifi, from Andrei
    Otcheretianski.

 3) Fix double free_irq in sgi ioc3 eth, from Thomas Bogendoerfer.

 4) Use after free in mptcp, from Florian Westphal.

 5) Use after free in wireguard's root_remove_peer_lists, from Eric
    Dumazet.

 6) Properly access packets heads in bonding alb code, from Eric
    Dumazet.

 7) Fix data race in skb_queue_len(), from Qian Cai.

 8) Fix regression in r8169 on some chips, from Heiner Kallweit.

 9) Fix XDP program ref counting in hv_netvsc, from Haiyang Zhang.

10) Certain kinds of set link netlink operations can cause a NULL deref
    in the ipv6 addrconf code. Fix from Eric Dumazet.

11) Don't cancel uninitialized work queue in drop monitor, from Ido
    Schimmel.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
  net: thunderx: use proper interface type for RGMII
  mt76: mt7615: fix max_nss in mt7615_eeprom_parse_hw_cap
  bpf: Improve bucket_log calculation logic
  selftests/bpf: Test freeing sockmap/sockhash with a socket in it
  bpf, sockhash: Synchronize_rcu before free'ing map
  bpf, sockmap: Don't sleep while holding RCU lock on tear-down
  bpftool: Don't crash on missing xlated program instructions
  bpf, sockmap: Check update requirements after locking
  drop_monitor: Do not cancel uninitialized work item
  mlxsw: spectrum_dpipe: Add missing error path
  mlxsw: core: Add validation of hardware device types for MGPIR register
  mlxsw: spectrum_router: Clear offload indication from IPv6 nexthops on abort
  selftests: mlxsw: Add test cases for local table route replacement
  mlxsw: spectrum_router: Prevent incorrect replacement of local table routes
  net: dsa: microchip: enable module autoprobe
  ipv6/addrconf: fix potential NULL deref in inet6_set_link_af()
  dpaa_eth: support all modes with rate adapting PHYs
  net: stmmac: update pci platform data to use phy_interface
  net: stmmac: xgmac: fix missing IFF_MULTICAST checki in dwxgmac2_set_filter
  net: stmmac: fix missing IFF_MULTICAST check in dwmac4_set_filter
  ...

VirtualBox hosts can share folders with guests, this commit adds a
VFS driver implementing the Linux-guest side of this, allowing folders
exported by the host to be mounted under Linux.

This driver depends on the guest <-> host IPC functions exported by
the vboxguest driver.
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull powerpc fixes from Michael Ellerman:

 - Fix an existing bug in our user access handling, exposed by one of
   the bug fixes we merged this cycle.

 - A fix for a boot hang on 32-bit with CONFIG_TRACE_IRQFLAGS and the
   recently added CONFIG_VMAP_STACK.

Thanks to: Christophe Leroy, Guenter Roeck.

* tag 'powerpc-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc: Fix CONFIG_TRACE_IRQFLAGS with CONFIG_VMAP_STACK
  powerpc/futex: Fix incorrect user access blocking

This is a merge error on my part - the driver was merged into mainline
by commit c5951e7c ("Merge tag 'mips_5.6' of git://../mips/linux")
over a week ago, but nobody apparently noticed that it didn't actually
build due to still having a reference to the devm_ioremap_nocache()
function, removed a few days earlier through commit 6a1000bd ("Merge
tag 'ioremap-5.6' of git://../ioremap").

Apparently this didn't get any build testing anywhere.  Not perhaps all
that surprising: it's restricted to 64-bit MIPS only, and only with the
new SGI_MFD_IOC3 support enabled.

I only noticed because the ioremap conflicts in the ARM SoC driver
update made me check there weren't any others hiding, and I found this
one.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARM SoC late updates from Olof Johansson:
 "This is some material that we picked up into our tree late, or that
  had more complex dependencies on more than one topic branch that makes
  sense to keep separately.

   - TI support for secure accelerators and hwrng on OMAP4/5

   - TI camera changes for dra7 and am437x and SGX improvement due to
     better reset control support on am335x, am437x and dra7

   - Davinci moves to proper clocksource on DM365, and regulator/audio
     improvements for DM365 and DM644x eval boards"

* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
  ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem
  ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt
  ARM: dts: Configure interconnect target module for am437x sgx
  ARM: dts: Configure sgx for dra7
  ARM: dts: Configure rstctrl reset for am335x SGX
  ARM: dts: dra7: Add ti-sysc node for VPE
  ARM: dts: dra7: add vpe clkctrl node
  ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries
  ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries
  ARM: dts: am43xx: add support for clkout1 clock
  arm: dts: dra76-evm: Add CAL and OV5640 nodes
  arm: dtsi: dra76x: Add CAL dtsi node
  arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
  ARM: dts: DRA72: Add CAL dtsi node
  ARM: dts: dra7-l4: Add ti-sysc node for CAM
  ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
  ARM: dts: dra7: add cam clkctrl node
  ARM: OMAP2+: Drop legacy platform data for omap4 des
  ARM: OMAP2+: Drop legacy platform data for omap4 sham
  ARM: OMAP2+: Drop legacy platform data for omap4 aes
  ...