IFC IO accressor are set at run time based
on IFC IP registers endianness.IFC node in
DTS file contains information about
endianness.
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>

Aquantia PHYs used on platforms such as T2080RDB, T1024RDB.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

The PHY uses XAUI interface to connect to MAC, mostly the PHY used on
riser card.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

Add support for INA220 current sensor.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

Add support for INA220 current sensor.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

This patch adds a few optimisations in memcpy functions by using
lbzu/stbu instead of lxb/stb and by re-ordering insn inside a loop
to reduce latency due to loading
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>

cacheable_memcpy uses dcbz instruction and is more efficient than
memcpy when the destination is in RAM. If the destination is in an
io area, memcpy_toio() is normally used, not memcpy

This patch renames memcpy as generic_memcpy, and renames
cacheable_memcpy as memcpy

On MPC885, we get approximatly 7% increase of the transfer rate
on an FTP reception
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>

cacheable_memzero() which has become the new memset() and the old
memset() are quite similar, so just merge them.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>

cacheable_memzero uses dcbz instruction and is more efficient than
memset(0) when the destination is in RAM

This patch renames memset as generic_memset, and defines memset
as a prolog to cacheable_memzero. This prolog checks if the byte
to set is 0. If not, it falls back to generic_memcpy()

cacheable_memzero disappears as it is not referenced anywhere anymore
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>

This partially reverts
commit 'powerpc: Remove duplicate cacheable_memcpy/memzero functions
("b05ae4ee")'

Functions cacheable_memcpy/memzero are more efficient than
memcpy/memset as they use the dcbz instruction which avoids refill
of the cacheline with the data that we will overwrite.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>

CPM muram is not cached, so use memset_io() instead of memset()
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>

__flush_dcache_icache_phys() requires the ability to access the
memory with the MMU disabled, which means that on a 32-bit system
any memory above 4 GiB is inaccessible.  In particular, mpc86xx is
32-bit and can have more than 4 GiB of RAM.
Signed-off-by: Scott Wood <scottwood@freescale.com>

The C version of csum_add() as defined in include/net/checksum.h gives
the following assembly in ppc32:
       0:       7c 04 1a 14     add     r0,r4,r3
       4:       7c 64 00 10     subfc   r3,r4,r0
       8:       7c 63 19 10     subfe   r3,r3,r3
       c:       7c 63 00 50     subf    r3,r3,r0
and the following in ppc64:
   0xc000000000001af8 <+0>:	add     r3,r3,r4
   0xc000000000001afc <+4>:	cmplw   cr7,r3,r4
   0xc000000000001b00 <+8>:	mfcr    r4
   0xc000000000001b04 <+12>:	rlwinm  r4,r4,29,31,31
   0xc000000000001b08 <+16>:	add     r3,r4,r3
   0xc000000000001b0c <+20>:	clrldi  r3,r3,32
   0xc000000000001b10 <+24>:	blr

include/net/checksum.h also offers the possibility to define an arch
specific function.  This patch provides a specific csum_add() inline
function.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>

csum_tcpudp_magic() is only a few instructions, and does modify
really few registers. So it is not worth having it as a separate
function and suffer function branching and saving of volatile
registers.

This patch makes it inline by use of the already existing
csum_tcpudp_nofold() function.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>

Unify mpc85xx and corenet configs using fragments, to ease maintenance
and avoid the sort of drift that the previous patch fixed.

Hardware and software options are separated, with the hope that other
embedded platforms could share the software options, and to make it
easier to maintain custom/alternate configs that focus on either
hardware or software options.

Due to the previous patch, this patch should not affect the results of
any of the affected defconfigs -- only how those results are achieved.
The resulting config is more or less the union of the options that any
of the configs previously selected.  No attempt was made in this (or
the previous) patch to edit out questionable options, but this patch
will make it easier to do so in future patches.
Signed-off-by: Scott Wood <scottwood@freescale.com>

The mpc85xx and corenet configs have many differences between them that
can't be explained by the target hardware of each config.  The next
patch will consolidate these targets using kconfig fragments; this
patch shows what the resulting defconfigs will look like (generated by
using savedefconfig on a fragment-generated config).
Signed-off-by: Scott Wood <scottwood@freescale.com>

corenet32_smp_defconfig is missing some things that modern distros
require, enable them.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Scott Wood <scottwood@freescale.com>

By default we enable DMA(CONFIG_FSL_DMA) support
which are needed on P2041RDB, P3041DS, P4080DS,
B4860QDS, etc.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

When detecting EEH error on non-existing PE, including the reserved
one, the PE is simply unfrozen without dumping the PHB diag-data,
which is useful for locating the root cause of the EEH error. The
patch dumps the PHB diag-data when non-existing PE reports error.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

On LE kernel, the non-existing PE number in BE format derived from
skiboot firmware isn't converted to LE format properly as following
kernel log indicates:

   EEH: Clear non-existing PHB#4-PE#200000000000000
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This patch adds one helper function 'sigcontext_vmx_regs' which computes
quad word aligned pointer for 'vmx_reserve' array element in sigcontext
structure making the code more readable.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Reword comment and fix build for CONFIG_ALTIVEC=n]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Commit ce48b210 "powerpc: Add VSX context save/restore, ptrace and
signal support" expanded the 'vmx_reserve' array element to contain 101
double words, but the comment block above was not updated.

Also reorder the constants in the array size declaration to reflect the
logic mentioned in the comment block above. This change helps in
explaining how the HW registers are represented in the array. But no
functional change.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Reworded change log and added whitespace around +'s]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Currently tm_orig_msr is getting used during process context switch only.
Then there is ckpt_regs which saves the checkpointed userspace context
The MSR slot contained in ckpt_regs structure can be used during process
context switch instead of tm_orig_msr, thus allowing us to drop it from
thread_struct structure. This patch does that change.
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Destroy afu->contexts_idr on release of an afu, reclaiming the allocated
memory.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Destroy cxl_adapter_idr on module exit, reclaiming the allocated memory.

This was detected by the following semantic patch (written by Luis Rodriguez
<mcgrof@suse.com>)
<SmPL>
@ defines_module_init @
declarer name module_init, module_exit;
declarer name DEFINE_IDR;
identifier init;
@@

module_init(init);

@ defines_module_exit @
identifier exit;
@@

module_exit(exit);

@ declares_idr depends on defines_module_init && defines_module_exit @
identifier idr;
@@

DEFINE_IDR(idr);

@ on_exit_calls_destroy depends on declares_idr && defines_module_exit @
identifier declares_idr.idr, defines_module_exit.exit;
@@

exit(void)
{
 ...
 idr_destroy(&idr);
 ...
}

@ missing_module_idr_destroy depends on declares_idr && defines_module_exit && !on_exit_calls_destroy @
identifier declares_idr.idr, defines_module_exit.exit;
@@

exit(void)
{
 ...
 +idr_destroy(&idr);
}
</SmPL>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This patch adds support for OPAL EPOW (Environmental and Power Warnings)
and DPO (Delayed Power Off) events for the PowerNV platform. These events
are generated on FSP (Flexible Service Processor) based systems. EPOW
events are generated due to various critical system conditions that
require system shutdown. A few examples of these conditions are high
ambient temperature or system running on UPS power with low UPS battery.
DPO event is generated in response to admin initiated system shutdown
request. Upon receipt of EPOW and DPO events the host kernel invokes
orderly_poweroff() for performing graceful system shutdown.
Signed-off-by: Vipin K Parashar <vipin@linux.vnet.ibm.com>
Acked-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

When releasing PE for SRIOV VF, the PE is forced to be frozen
wrongly. When the same PE is picked for another VF, it won't
work anyhow. The patch fixes the issue by unfreezing, not
freezing the VF PE when releasing it.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The PELTV of PF PE should include VF PE, which is missed by current
code, so that the VF PE is frozen automatically when freezing PF PE.
The patch fixes the PELTV of PF PE to include VF PE.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

On PHB3, PE might be reserved in advance to reflect the M64 segments
consumed by the PE according to M64 BARs (exclude VF BARs) of the PCI
devices included in the PE. The PE is picked based on M64 BARs instead
of the bridge's M64 windows, which might include VF BARs. Otherwise,
wrong PE could be picked.

The patch calculates the used M64 segments and PE numbers according to
the M64 BARs, excluding VF BARs, of PCI devices in one particular PE,
instead of the bridge's M64 windows. Then the right PE number is picked.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The patch changes the type of last argument of pnv_ioda_setup_bus_PE()
and phb::pick_m64_pe() to boolean. No functional change.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

On PHB3, some PEs might be reserved in advance to reflect the M64
segments consumed by those PEs. We're reserving PEs based on the
M64 window of root port, which might contain VF BAR. The PEs for
VFs are allocated dynamically, not reserved based on the consumed
M64 segments. So the M64 window of root port isn't reliable for
the task. Instead, we go through M64 BARs (VF BARs excluded) of
PCI devices under the specified root bus and reserve PEs accordingly,
as the patch does.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The PE numbers are reserved according to root port's M64 window,
which is aligned to M64 segment finely. So one PE shouldn't be
reserved for multiple times. We will reserve PE numbers according
to the M64 BARs of PCI device in subsequent patches, which aren't
aligned to M64 segment size finely. It means one particular PE
could be reserved for multiple times.

The patch allows one PE to be reserved for multiple times and we
print the warning message at debugging level.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

mtmsr() does the right thing on 32bit and 64bit, so use it everywhere.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The encoding of the lengths in the ibm_architecture_vec array is
"interesting" to say the least. It's non-obvious how the number of bytes
we provide relates to the length value.

In fact we already got it wrong once, see 11e9ed43 "Fix up
ibm_architecture_vec definition".

So add some macros to make it (hopefully) clearer. These at least have
the property that the integer present in the code is equal to the number
of bytes that follows it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com>

This patch adds the ability to the DMA direct ops to fallback to the IOMMU
ops for coherent alloc/free if the coherent mask of the device isn't
suitable for accessing the direct DMA space and the device also happens
to have an active IOMMU table.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Now that the table and the offset can co-exist, we no longer need
to flip/flop, we can just establish both once at boot time.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

To support "hybrid" DMA ops in a subsequent patch, we will need both
a direct DMA offset and an iommu pointer. Those are currently exclusive
(a union), so change them to be separate fields.

While there, also type iommu_table_base properly and make exist only
on CONFIG_PPC64 since it's not referenced on 32-bit at all.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

A precision of 16 (%.16llx) has the same effect as a field width of 16
along with passing the 0 flag (%016llx), but the latter is much more
common in the kernel tree. Update cxl to use that.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

C99 says that a precision given as simply '.' with no following digits
or * should be interpreted as 0. The kernel's printf implementation,
however, treats this case as if the precision was omitted. C99 also
says that if both the precision and value are 0, no digits should be
printed. Even if the kernel followed C99 to the letter, I don't think
that would be particularly useful in these cases. For consistency with
most other format strings in the file, use an explicit precision of 16
and add a 0x prefix.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>