- 16 Nov, 2020 9 commits
-
-
Zhang Changzhong authored
Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: ca139d76 ("cx82310_eth: re-enable ethernet mode after router reboot") Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Zhang Changzhong <zhangchangzhong@huawei.com> Link: https://lore.kernel.org/r/1605247627-15385-1-git-send-email-zhangchangzhong@huawei.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Raju Rangoju authored
Update cxgb4 and cxgb3 driver maintainer Signed-off-by:
Raju Rangoju <rajur@chelsio.com> Link: https://lore.kernel.org/r/20201116104322.3959-1-rajur@chelsio.comSigned-off-by:
-
Martin Blumenstingl authored
A user reports (slightly shortened from the original message): libphy: lantiq,xrx200-mdio: probed mdio_bus 1e108000.switch-mii: MDIO device at address 17 is missing. gswip 1e108000.switch lan: no phy at 2 gswip 1e108000.switch lan: failed to connect to port 2: -19 lantiq,xrx200-net 1e10b308.eth eth0: error -19 setting up slave phy This is a single-port board using the internal Fast Ethernet PHY. The user reports that switching to PHY scanning instead of configuring the PHY within device-tree works around this issue. The documentation for the standalone variant of the PHY11G (which is probably very similar to what is used inside the xRX200 SoCs but having the firmware burnt onto that standalone chip in the factory) states that the PHY needs 300ms to be ready for MDIO communication after releasing the reset. Add a 300ms delay after initializing all GPHYs to ensure that the GPHY firmware had enough time to initialize and to appear on the MDIO bus. Unfortunately there is no (known) documentation on what the minimum time to wait after releasing the reset on an internal PHY so play safe and take the one for the external variant. Only wait after the last GPHY firmware is loaded to not slow down the initialization too much ( xRX200 has two GPHYs but newer SoCs have at least three GPHYs). Fixes: 14fceff4 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200") Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Acked-by:
Hauke Mehrtens <hauke@hauke-m.de> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20201115165757.552641-1-martin.blumenstingl@googlemail.comSigned-off-by:
-
Xie He authored
Martin Schiller is an active developer and reviewer for the X.25 code. His company is providing products based on the Linux X.25 stack. So he is a good candidate for maintainers of the X.25 code. The original maintainer of the X.25 network layer (Andrew Hendry) has not sent any email to the netdev mail list since 2013. So he is probably inactive now. Cc: Andrew Hendry <andrew.hendry@gmail.com> Signed-off-by:
Xie He <xie.he.0141@gmail.com> Acked-by:
Martin Schiller <ms@dev.tdt.de> Link: https://lore.kernel.org/r/20201114111029.326972-1-xie.he.0141@gmail.comSigned-off-by:
-
Georg Kohmann authored
Packets are processed even though the first fragment don't include all headers through the upper layer header. This breaks TAHI IPv6 Core Conformance Test v6LC.1.3.6. Referring to RFC8200 SECTION 4.5: "If the first fragment does not include all headers through an Upper-Layer header, then that fragment should be discarded and an ICMP Parameter Problem, Code 3, message should be sent to the source of the fragment, with the Pointer field set to zero." The fragment needs to be validated the same way it is done in commit 2efdaaaf ("IPv6: reply ICMP error if the first fragment don't include all headers") for ipv6. Wrap the validation into a common function, ipv6_frag_thdr_truncated() to check for truncation in the upper layer header. This validation does not fullfill all aspects of RFC 8200, section 4.5, but is at the moment sufficient to pass mentioned TAHI test. In netfilter, utilize the fragment offset returned by find_prev_fhdr() to let ipv6_frag_thdr_truncated() start it's traverse from the fragment header. Return 0 to drop the fragment in the netfilter. This is the same behaviour as used on other protocol errors in this function, e.g. when nf_ct_frag6_queue() returns -EPROTO. The Fragment will later be picked up by ipv6_frag_rcv() in reassembly.c. ipv6_frag_rcv() will then send an appropriate ICMP Parameter Problem message back to the source. References commit 2efdaaaf ("IPv6: reply ICMP error if the first fragment don't include all headers") Signed-off-by:
Georg Kohmann <geokohma@cisco.com> Acked-by:
Pablo Neira Ayuso <pablo@netfilter.org> Link: https://lore.kernel.org/r/20201111115025.28879-1-geokohma@cisco.comSigned-off-by:
-
Jakub Kicinski authored
Zhang Qilong says: ==================== Fix usage counter leak by adding a general sync ops In many case, we need to check return value of pm_runtime_get_sync, but it brings a trouble to the usage counter processing. Many callers forget to decrease the usage counter when it failed, which could resulted in reference leak. It has been discussed a lot[0][1]. So we add a function to deal with the usage counter for better coding and view. Then, we replace pm_runtime_resume_and_get with it in fec_main.c to avoid it. [0] https://lkml.org/lkml/2020/6/14/88 [1] https://patchwork.ozlabs.org/project/linux-tegra/list/?series=178139 ==================== Link: https://lore.kernel.org/r/20201110092933.3342784-1-zhangqilong3@huawei.comSigned-off-by:
-
Zhang Qilong authored
pm_runtime_get_sync() will increment pm usage at first and it will resume the device later. If runtime of the device has error or device is in inaccessible state(or other error state), resume operation will fail. If we do not call put operation to decrease the reference, it will result in reference count leak. Moreover, this device cannot enter the idle state and always stay busy or other non-idle state later. So we fixed it by replacing it with pm_runtime_resume_and_get. Fixes: 8fff755e ("net: fec: Ensure clocks are enabled while using mdio bus") Signed-off-by:
Zhang Qilong <zhangqilong3@huawei.com> Signed-off-by:
-
Zhang Qilong authored
In many case, we need to check return value of pm_runtime_get_sync, but it brings a trouble to the usage counter processing. Many callers forget to decrease the usage counter when it failed, which could resulted in reference leak. It has been discussed a lot[0][1]. So we add a function to deal with the usage counter for better coding. [0]https://lkml.org/lkml/2020/6/14/88 [1]https://patchwork.ozlabs.org/project/linux-tegra/list/?series=178139Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Jakub Kicinski authored
Merge tag 'linux-can-fixes-for-5.10-20201115' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2020-11-15 Anant Thazhemadam contributed two patches for the AF_CAN that prevent potential access of uninitialized member in can_rcv() and canfd_rcv(). The next patch is by Alejandro Concepcion Rodriguez and changes can_restart() to use the correct function to push a skb into the networking stack from process context. Zhang Qilong's patch fixes a memory leak in the error path of the ti_hecc's probe function. A patch by me fixes mcba_usb_start_xmit() function in the mcba_usb driver, to first fill the skb and then pass it to can_put_echo_skb(). Colin Ian King's patch fixes a potential integer overflow on shift in the peak_usb driver. The next two patches target the flexcan driver, a patch by me adds the missing "req_bit" to the stop mode property comment (which was broken during net-next for v5.10). Zhang Qilong's patch fixes the failure handling of pm_runtime_get_sync(). The next seven patches target the m_can driver including the tcan4x5x spi driver glue code. Enric Balletbo i Serra's patch for the tcan4x5x Kconfig fix the REGMAP_SPI dependency handling. A patch by me for the tcan4x5x driver's probe() function adds missing error handling to for devm_regmap_init(), and in tcan4x5x_can_remove() the order of deregistration is fixed. Wu Bo's patch for the m_can driver fixes the state change handling in m_can_handle_state_change(). Two patches by Dan Murphy first introduce m_can_class_free_dev() and then make use of it to fix the freeing of the can device. A patch by Faiz Abbas add a missing shutdown of the CAN controller in the m_can_stop() function. * tag 'linux-can-fixes-for-5.10-20201115' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can: can: m_can: m_can_stop(): set device to software init mode before closing can: m_can: Fix freeing of can device from peripherials can: m_can: m_can_class_free_dev(): introduce new function can: m_can: m_can_handle_state_change(): fix state change can: tcan4x5x: tcan4x5x_can_remove(): fix order of deregistration can: tcan4x5x: tcan4x5x_can_probe(): add missing error checking for devm_regmap_init() can: tcan4x5x: replace depends on REGMAP_SPI with depends on SPI can: flexcan: fix failure handling of pm_runtime_get_sync() can: flexcan: flexcan_setup_stop_mode(): add missing "req_bit" to stop mode property comment can: peak_usb: fix potential integer overflow on shift of a int can: mcba_usb: mcba_usb_start_xmit(): first fill skb, then pass to can_put_echo_skb() can: ti_hecc: Fix memleak in ti_hecc_probe can: dev: can_restart(): post buffer from the right context can: af_can: prevent potential access of uninitialized member in canfd_rcv() can: af_can: prevent potential access of uninitialized member in can_rcv() ==================== Link: https://lore.kernel.org/r/20201115174131.2089251-1-mkl@pengutronix.deSigned-off-by:
-
- 15 Nov, 2020 17 commits
-
-
Faiz Abbas authored
There might be some requests pending in the buffer when the interface close sequence occurs. In some devices, these pending requests might lead to the module not shutting down properly when m_can_clk_stop() is called. Therefore, move the device to init state before potentially powering it down. Fixes: e0d1f481 ("can: m_can: add Bosch M_CAN controller support") Signed-off-by:
Faiz Abbas <faiz_abbas@ti.com> Acked-by:
Dan Murphy <dmurphy@ti.com> Link: https://lore.kernel.org/r/20200825055442.16994-1-faiz_abbas@ti.comSigned-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Dan Murphy authored
Fix leaking netdev device from peripherial devices. The call to allocate the netdev device is made from and managed by the peripherial. Fixes: f524f829 ("can: m_can: Create a m_can platform framework") Reported-by:
-
Dan Murphy authored
This patch creates a common function that peripherials can call to free the netdev device when failures occur. Fixes: f524f829 ("can: m_can: Create a m_can platform framework") Reported-by:
-
Wu Bo authored
m_can_handle_state_change() is called with the new_state as an argument. In the switch statements for CAN_STATE_ERROR_ACTIVE, the comment and the following code indicate that a CAN_STATE_ERROR_WARNING is handled. This patch fixes this problem by changing the case to CAN_STATE_ERROR_WARNING. Signed-off-by:
Wu Bo <wubo.oduw@gmail.com> Link: http://lore.kernel.org/r/20200129022330.21248-2-wubo.oduw@gmail.com Cc: Dan Murphy <dmurphy@ti.com> Fixes: e0d1f481 ("can: m_can: add Bosch M_CAN controller support") Signed-off-by:
-
Marc Kleine-Budde authored
Change the order in tcan4x5x_can_remove() to be the exact inverse of tcan4x5x_can_probe(). First m_can_class_unregister(), then power down the device. Fixes: 5443c226 ("can: tcan4x5x: Add tcan4x5x driver to the kernel") Cc: Dan Murphy <dmurphy@ti.com> Link: http://lore.kernel.org/r/20201019154233.1262589-10-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch adds the missing error checking when initializing the regmap interface fails. Fixes: 5443c226 ("can: tcan4x5x: Add tcan4x5x driver to the kernel") Cc: Dan Murphy <dmurphy@ti.com> Link: http://lore.kernel.org/r/20201019154233.1262589-7-mkl@pengutronix.deSigned-off-by:
-
Enric Balletbo i Serra authored
regmap is a library function that gets selected by drivers that need it. No driver modules should depend on it. Instead depends on SPI and select REGMAP_SPI. Depending on REGMAP_SPI makes this driver only build if another driver already selected REGMAP_SPI, as the symbol can't be selected through the menu kernel configuration. Signed-off-by:
Enric Balletbo i Serra <enric.balletbo@collabora.com> Link: http://lore.kernel.org/r/20200413141013.506613-1-enric.balletbo@collabora.comReviewed-by:
-
Zhang Qilong authored
pm_runtime_get_sync() will increment pm usage at first and it will resume the device later. If runtime of the device has error or device is in inaccessible state(or other error state), resume operation will fail. If we do not call put operation to decrease the reference, it will result in reference leak in the two functions flexcan_get_berr_counter() and flexcan_open(). Moreover, this device cannot enter the idle state and always stay busy or other non-idle state later. So we should fix it through adding pm_runtime_put_noidle(). Fixes: ca109896 ("can: flexcan: implement can Runtime PM") Signed-off-by:
-
Marc Kleine-Budde authored
In the patch d9b081e3 ("can: flexcan: remove ack_grp and ack_bit handling from driver") the unused ack_grp and ack_bit were removed from the driver. However in the comment, the "req_bit" was accidentally removed, too. This patch adds back the "req_bit" bit. Fixes: d9b081e3 ("can: flexcan: remove ack_grp and ack_bit handling from driver") Reported-by:Joakim Zhang <qiangqing.zhang@nxp.com> Link: http://lore.kernel.org/r/20201014114810.2911135-1-mkl@pengutronix.deSigned-off-by:
-
Colin Ian King authored
The left shift of int 32 bit integer constant 1 is evaluated using 32 bit arithmetic and then assigned to a signed 64 bit variable. In the case where time_ref->adapter->ts_used_bits is 32 or more this can lead to an oveflow. Avoid this by shifting using the BIT_ULL macro instead. Fixes: bb478555 ("can: usb: PEAK-System Technik USB adapters driver core") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20201105112427.40688-1-colin.king@canonical.comSigned-off-by:
-
Marc Kleine-Budde authored
The driver has to first fill the skb with data and then handle it to can_put_echo_skb(). This patch moves the can_put_echo_skb() down, right before sending the skb out via USB. Fixes: 51f3baad ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer") Cc: Remigiusz Kołłątaj <remigiusz.kollataj@mobica.com> Link: https://lore.kernel.org/r/20201111221204.1639007-1-mkl@pengutronix.deSigned-off-by:
-
Zhang Qilong authored
In the error handling, we should goto the probe_exit_candev to free ndev to prevent memory leak. Fixes: dabf54dd ("can: ti_hecc: Convert TI HECC driver to DT only driver") Signed-off-by:
-
Alejandro Concepcion Rodriguez authored
netif_rx() is meant to be called from interrupt contexts. can_restart() may be called by can_restart_work(), which is called from a worqueue, so it may run in process context. Use netif_rx_ni() instead. Fixes: 39549eef ("can: CAN Network device driver and Netlink interface") Co-developed-by:
Loris Fauster <loris.fauster@ttcontrol.com> Signed-off-by:
Alejandro Concepcion Rodriguez <alejandro@acoro.eu> Link: https://lore.kernel.org/r/4e84162b-fb31-3a73-fa9a-9438b4bd5234@acoro.eu [mkl: use netif_rx_ni() instead of netif_rx_any_context()] Signed-off-by:
-
Anant Thazhemadam authored
In canfd_rcv(), cfd->len is uninitialized when skb->len = 0, and this uninitialized cfd->len is accessed nonetheless by pr_warn_once(). Fix this uninitialized variable access by checking cfd->len's validity condition (cfd->len > CANFD_MAX_DLEN) separately after the skb->len's condition is checked, and appropriately modify the log messages that are generated as well. In case either of the required conditions fail, the skb is freed and NET_RX_DROP is returned, same as before. Fixes: d4689846 ("can: af_can: canfd_rcv(): replace WARN_ONCE by pr_warn_once") Reported-by: syzbot+9bcb0c9409066696d3aa@syzkaller.appspotmail.com Tested-by:
Anant Thazhemadam <anant.thazhemadam@gmail.com> Signed-off-by:
-
Anant Thazhemadam authored
In can_rcv(), cfd->len is uninitialized when skb->len = 0, and this uninitialized cfd->len is accessed nonetheless by pr_warn_once(). Fix this uninitialized variable access by checking cfd->len's validity condition (cfd->len > CAN_MAX_DLEN) separately after the skb->len's condition is checked, and appropriately modify the log messages that are generated as well. In case either of the required conditions fail, the skb is freed and NET_RX_DROP is returned, same as before. Fixes: 8cb68751 ("can: af_can: can_rcv(): replace WARN_ONCE by pr_warn_once") Reported-by: syzbot+9bcb0c9409066696d3aa@syzkaller.appspotmail.com Tested-by:
-
Wang Hai authored
If sb_occ_port_pool_get() failed in devlink_nl_sb_port_pool_fill(), msg should be canceled by genlmsg_cancel(). Fixes: df38dafd ("devlink: implement shared buffer occupancy monitoring interface") Reported-by:
Wang Hai <wanghai38@huawei.com> Link: https://lore.kernel.org/r/20201113111622.11040-1-wanghai38@huawei.comSigned-off-by:
-
Jisheng Zhang authored
If the phy enables power saving technology, the dwmac's software reset needs more time to complete, enlarge dma reset timeout to 200000us. Signed-off-by:
Jisheng Zhang <Jisheng.Zhang@synaptics.com> Link: https://lore.kernel.org/r/20201113090902.5c7aab1a@xhacker.debianSigned-off-by:
-
- 14 Nov, 2020 9 commits
-
-
Sven Van Asbroeck authored
On arm imx6, when opening the chip's netdev, the whole Linux kernel intermittently hangs/freezes. This is caused by a bug in the driver code which tests if pcie interrupts are working correctly, using the software interrupt: 1. open: enable the software interrupt 2. open: tell the chip to assert the software interrupt 3. open: wait for flag 4. ISR: acknowledge s/w interrupt, set flag 5. open: notice flag, disable the s/w interrupt, continue Unfortunately the ISR only acknowledges the s/w interrupt, but does not disable it. This will re-trigger the ISR in a tight loop. On some (lucky) platforms, open proceeds to disable the s/w interrupt even while the ISR is 'spinning'. On arm imx6, the spinning ISR does not allow open to proceed, resulting in a hung Linux kernel. Fix minimally by disabling the s/w interrupt in the ISR, which will prevent it from spinning. This won't break anything because the s/w interrupt is used as a one-shot interrupt. Note that this is a minimal fix, overlooking many possible cleanups, e.g.: - lan743x_intr_software_isr() is completely redundant and reads INT_STS twice for no apparent reason - disabling the s/w interrupt in lan743x_intr_test_isr() is now redundant, but harmless - waiting on software_isr_flag can be converted from a sleeping poll loop to wait_event_timeout() Fixes: 23f0703c ("lan743x: Add main source files for new lan743x driver") Tested-by: Sven Van Asbroeck <thesven73@gmail.com> # arm imx6 lan7430 Signed-off-by:
Sven Van Asbroeck <thesven73@gmail.com> Link: https://lore.kernel.org/r/20201112204741.12375-1-TheSven73@gmail.comSigned-off-by:
-
Sven Van Asbroeck authored
When running this chip on arm imx6, we intermittently observe the following kernel warning in the log, especially when the system is under high load: [ 50.119484] ------------[ cut here ]------------ [ 50.124377] WARNING: CPU: 0 PID: 303 at kernel/softirq.c:169 __local_bh_enable_ip+0x100/0x184 [ 50.132925] IRQs not enabled as expected [ 50.159250] CPU: 0 PID: 303 Comm: rngd Not tainted 5.7.8 #1 [ 50.164837] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) [ 50.171395] [<c0111a38>] (unwind_backtrace) from [<c010be28>] (show_stack+0x10/0x14) [ 50.179162] [<c010be28>] (show_stack) from [<c05b9dec>] (dump_stack+0xac/0xd8) [ 50.186408] [<c05b9dec>] (dump_stack) from [<c0122e40>] (__warn+0xd0/0x10c) [ 50.193391] [<c0122e40>] (__warn) from [<c0123238>] (warn_slowpath_fmt+0x98/0xc4) [ 50.200892] [<c0123238>] (warn_slowpath_fmt) from [<c012b010>] (__local_bh_enable_ip+0x100/0x184) [ 50.209860] [<c012b010>] (__local_bh_enable_ip) from [<bf09ecbc>] (destroy_conntrack+0x48/0xd8 [nf_conntrack]) [ 50.220038] [<bf09ecbc>] (destroy_conntrack [nf_conntrack]) from [<c0ac9b58>] (nf_conntrack_destroy+0x94/0x168) [ 50.230160] [<c0ac9b58>] (nf_conntrack_destroy) from [<c0a4aaa0>] (skb_release_head_state+0xa0/0xd0) [ 50.239314] [<c0a4aaa0>] (skb_release_head_state) from [<c0a4aadc>] (skb_release_all+0xc/0x24) [ 50.247946] [<c0a4aadc>] (skb_release_all) from [<c0a4b4cc>] (consume_skb+0x74/0x17c) [ 50.255796] [<c0a4b4cc>] (consume_skb) from [<c081a2dc>] (lan743x_tx_release_desc+0x120/0x124) [ 50.264428] [<c081a2dc>] (lan743x_tx_release_desc) from [<c081a98c>] (lan743x_tx_napi_poll+0x5c/0x18c) [ 50.273755] [<c081a98c>] (lan743x_tx_napi_poll) from [<c0a6b050>] (net_rx_action+0x118/0x4a4) [ 50.282306] [<c0a6b050>] (net_rx_action) from [<c0101364>] (__do_softirq+0x13c/0x53c) [ 50.290157] [<c0101364>] (__do_softirq) from [<c012b29c>] (irq_exit+0x150/0x17c) [ 50.297575] [<c012b29c>] (irq_exit) from [<c0196a08>] (__handle_domain_irq+0x60/0xb0) [ 50.305423] [<c0196a08>] (__handle_domain_irq) from [<c05d44fc>] (gic_handle_irq+0x4c/0x90) [ 50.313790] [<c05d44fc>] (gic_handle_irq) from [<c0100ed4>] (__irq_usr+0x54/0x80) [ 50.321287] Exception stack(0xecd99fb0 to 0xecd99ff8) [ 50.326355] 9fa0: 1cf1aa74 00000001 00000001 00000000 [ 50.334547] 9fc0: 00000001 00000000 00000000 00000000 00000000 00000000 00004097 b6d17d14 [ 50.342738] 9fe0: 00000001 b6d17c60 00000000 b6e71f94 800b0010 ffffffff [ 50.349364] irq event stamp: 2525027 [ 50.352955] hardirqs last enabled at (2525026): [<c0a6afec>] net_rx_action+0xb4/0x4a4 [ 50.360892] hardirqs last disabled at (2525027): [<c0d6d2fc>] _raw_spin_lock_irqsave+0x1c/0x50 [ 50.369517] softirqs last enabled at (2524660): [<c01015b4>] __do_softirq+0x38c/0x53c [ 50.377446] softirqs last disabled at (2524693): [<c012b29c>] irq_exit+0x150/0x17c [ 50.385027] ---[ end trace c0b571db4bc8087d ]--- The driver is calling dev_kfree_skb() from code inside a spinlock, where h/w interrupts are disabled. This is forbidden, as documented in include/linux/netdevice.h. The correct function to use dev_kfree_skb_irq(), or dev_kfree_skb_any(). Fix by using the correct dev_kfree_skb_xxx() functions: in lan743x_tx_release_desc(): called by lan743x_tx_release_completed_descriptors() called by in lan743x_tx_napi_poll() which holds a spinlock called by lan743x_tx_release_all_descriptors() called by lan743x_tx_close() which can-sleep conclusion: use dev_kfree_skb_any() in lan743x_tx_xmit_frame(): which holds a spinlock conclusion: use dev_kfree_skb_irq() in lan743x_tx_close(): which can-sleep conclusion: use dev_kfree_skb() in lan743x_rx_release_ring_element(): called by lan743x_rx_close() which can-sleep called by lan743x_rx_open() which can-sleep conclusion: use dev_kfree_skb() Fixes: 23f0703c ("lan743x: Add main source files for new lan743x driver") Signed-off-by: -
Paul Moore authored
Static checking revealed that a previous fix to netlbl_unlabel_staticlist() leaves a stack variable uninitialized, this patches fixes that. Fixes: 866358ec ("netlabel: fix our progress tracking in netlbl_unlabel_staticlist()") Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Paul Moore <paul@paul-moore.com> Reviewed-by:
James Morris <jamorris@linux.microsoft.com> Link: https://lore.kernel.org/r/160530304068.15651.18355773009751195447.stgit@siflSigned-off-by:
-
Xin Long authored
A call trace was found in Hangbin's Codenomicon testing with debug kernel: [ 2615.981988] ODEBUG: free active (active state 0) object type: timer_list hint: sctp_generate_proto_unreach_event+0x0/0x3a0 [sctp] [ 2615.995050] WARNING: CPU: 17 PID: 0 at lib/debugobjects.c:328 debug_print_object+0x199/0x2b0 [ 2616.095934] RIP: 0010:debug_print_object+0x199/0x2b0 [ 2616.191533] Call Trace: [ 2616.194265] <IRQ> [ 2616.202068] debug_check_no_obj_freed+0x25e/0x3f0 [ 2616.207336] slab_free_freelist_hook+0xeb/0x140 [ 2616.220971] kfree+0xd6/0x2c0 [ 2616.224293] rcu_do_batch+0x3bd/0xc70 [ 2616.243096] rcu_core+0x8b9/0xd00 [ 2616.256065] __do_softirq+0x23d/0xacd [ 2616.260166] irq_exit+0x236/0x2a0 [ 2616.263879] smp_apic_timer_interrupt+0x18d/0x620 [ 2616.269138] apic_timer_interrupt+0xf/0x20 [ 2616.273711] </IRQ> This is because it holds asoc when transport->proto_unreach_timer starts and puts asoc when the timer stops, and without holding transport the transport could be freed when the timer is still running. So fix it by holding/putting transport instead for proto_unreach_timer in transport, just like other timers in transport. v1->v2: - Also use sctp_transport_put() for the "out_unlock:" path in sctp_generate_proto_unreach_event(), as Marcelo noticed. Fixes: 50b5d6ad ("sctp: Fix a race between ICMP protocol unreachable and connect()") Reported-by:Hangbin Liu <liuhangbin@gmail.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Link: https://lore.kernel.org/r/102788809b554958b13b95d33440f5448113b8d6.1605331373.git.lucien.xin@gmail.comSigned-off-by:
-
Stefano Garzarella authored
Before commit c0cfa2d8 ("vsock: add multi-transports support"), if a G2H transport was loaded (e.g. virtio transport), every packets was forwarded to the host, regardless of the destination CID. The H2G transports implemented until then (vhost-vsock, VMCI) always responded with an error, if the destination CID was not VMADDR_CID_HOST. From that commit, we are using the remote CID to decide which transport to use, so packets with remote CID > VMADDR_CID_HOST(2) are sent only through H2G transport. If no H2G is available, packets are discarded directly in the guest. Some use cases (e.g. Nitro Enclaves [1]) rely on the old behaviour to implement sibling VMs communication, so we restore the old behavior when no H2G is registered. It will be up to the host to discard packets if the destination is not the right one. As it was already implemented before adding multi-transport support. Tested with nested QEMU/KVM by me and Nitro Enclaves by Andra. [1] Documentation/virt/ne_overview.rst Cc: Jorgen Hansen <jhansen@vmware.com> Cc: Dexuan Cui <decui@microsoft.com> Fixes: c0cfa2d8 ("vsock: add multi-transports support") Reported-by:
Andra Paraschiv <andraprs@amazon.com> Tested-by:
Stefano Garzarella <sgarzare@redhat.com> Link: https://lore.kernel.org/r/20201112133837.34183-1-sgarzare@redhat.comSigned-off-by:
-
Tobias Waldekranz authored
As soon as you add the second port to a VLAN, all other port membership configuration is overwritten with zeroes. The HW interprets this as all ports being "unmodified members" of the VLAN. In the simple case when all ports belong to the same VLAN, switching will still work. But using multiple VLANs or trying to set multiple ports as tagged members will not work. On the 6352, doing a VTU GetNext op, followed by an STU GetNext op will leave you with both the member- and state- data in the VTU/STU data registers. But on the 6097 (which uses the same implementation), the STU GetNext will override the information gathered from the VTU GetNext. Separate the two stages, parsing the result of the VTU GetNext before doing the STU GetNext. We opt to update the existing implementation for all applicable chips, as opposed to creating a separate callback for 6097, because although the previous implementation did work for (at least) 6352, the datasheet does not mention the masking behavior. Fixes: ef6fcea3 ("net: dsa: mv88e6xxx: get STU entry on VTU GetNext") Signed-off-by:
Tobias Waldekranz <tobias@waldekranz.com> Link: https://lore.kernel.org/r/20201112114335.27371-1-tobias@waldekranz.comSigned-off-by:
-
Zhang Changzhong authored
Add the missing clk_disable_unprepare() before return from smsc_phy_probe() in the error handling case. Fixes: bedd8d78 ("net: phy: smsc: LAN8710/20: add phy refclk in support") Reported-by:
-
Zhang Qilong authored
genlmsg_cancel() needs to be called in the error path of inet6_fill_ifmcaddr and inet6_fill_ifacaddr to cancel the message. Fixes: 6ecf4c37 ("ipv6: enable IFA_TARGET_NETNSID for RTM_GETADDR") Reported-by:
-
Yi-Hung Wei authored
Currently, we may set the tunnel option flag when the size of metadata is zero. For example, we set TUNNEL_GENEVE_OPT in the receive function no matter the geneve option is present or not. As this may result in issues on the tunnel flags consumers, this patch fixes the issue. Related discussion: * https://lore.kernel.org/netdev/1604448694-19351-1-git-send-email-yihung.wei@gmail.com/T/#u Fixes: 256c87c1 ("net: check tunnel option type in tunnel flags") Signed-off-by:
Yi-Hung Wei <yihung.wei@gmail.com> Link: https://lore.kernel.org/r/1605053800-74072-1-git-send-email-yihung.wei@gmail.comSigned-off-by:
-
- 13 Nov, 2020 5 commits
-
-
Wang Qing authored
We always have to update the value of ret, otherwise the error value may be the previous one. Fixes: f6bd5952 ("net: ethernet: ti: introduce am654 common platform time sync driver") Signed-off-by:
Wang Qing <wangqing@vivo.com> [grygorii.strashko@ti.com: fix build warn, subj add fixes tag] Signed-off-by:
Grygorii Strashko <grygorii.strashko@ti.com> Acked-by:
Richard Cochran <richardcochran@gmail.com> Link: https://lore.kernel.org/r/20201112164541.3223-1-grygorii.strashko@ti.comSigned-off-by:
-
Wang Hai authored
Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: 4c2703df ("net: marvell: prestera: Add PCI interface support") Reported-by:
Vadym Kochan <vadym.kochan@plvision.eu> Acked-by:
-
Steen Hegelund authored
Selecting VSC8575 as a MACSec PHY was not correct The relevant datasheet can be found here: - VSC8575: https://www.microchip.com/wwwproducts/en/VSC8575 History: v1 -> v2: - Corrected the sha in the "Fixes:" tag Fixes: 1bbe0ecc ("net: phy: mscc: macsec initialization") Signed-off-by:
Steen Hegelund <steen.hegelund@microchip.com> Reviewed-by:
Antoine Tenart <atenart@kernel.org> Link: https://lore.kernel.org/r/20201113091116.1102450-1-steen.hegelund@microchip.comSigned-off-by:
-
Jeff Dike authored
Commit 58956317 ("neighbor: Improve garbage collection") guarantees neighbour table entries a five-second lifetime. Processes which make heavy use of multicast can fill the neighour table with multicast addresses in five seconds. At that point, neighbour entries can't be GC-ed because they aren't five seconds old yet, the kernel log starts to fill up with "neighbor table overflow!" messages, and sends start to fail. This patch allows multicast addresses to be thrown out before they've lived out their five seconds. This makes room for non-multicast addresses and makes messages to all addresses more reliable in these circumstances. Fixes: 58956317 ("neighbor: Improve garbage collection") Signed-off-by:
Jeff Dike <jdike@akamai.com> Reviewed-by:
David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20201113015815.31397-1-jdike@akamai.comSigned-off-by:
-
Grygorii Strashko authored
Depending on the SoC/platform the CPSW can completely lose context after a suspend/resume cycle, including CPSW wrapper (WR) which will cause reset of WR_C0_MISC_EN register, so CPTS IRQ will became disabled. Fix it by moving CPTS IRQ enabling in cpsw_ndo_open() where CPTS is actually started. Fixes: 84ea9c0a ("net: ethernet: ti: cpsw: enable cpts irq") Reported-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
