- 12 Dec, 2023 17 commits
-
-
Johannes Berg authored
Sometimes there may be reasons for which a BSS that's actually found in scan cannot be used to connect to, for example a nonprimary link of an NSTR mobile AP MLD cannot be used for normal direct connections to it. Not indicating these to userspace as we do now of course avoids being able to connect to them, but it's better if they're shown to userspace and it can make an appropriate decision, without e.g. doing an additional ML probe. Thus add an indication of what a BSS can be used for, currently "normal" and "MLD link", including a reason bitmap for it being not usable. The latter can be extended later for certain BSSes if there are other reasons they cannot be used. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Reviewed-by:
Ilan Peer <ilan.peer@intel.com> Reviewed-by:
Gregory Greenman <gregory.greenman@intel.com> Signed-off-by:
Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://msgid.link/20231211085121.0464f25e0b1d.I9f70ca9f1440565ad9a5207d0f4d00a20cca67e7@changeidSigned-off-by:
-
Emmanuel Grumbach authored
Newest firmware has completely offloaded this logic and this command will be deprecated soon. Based on a capability bit advertised by the firmware, skip this command. Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Johannes Berg authored
There's only one user of this code, which is STA unblock during sleep for uAPSD on really old devices. Instead of having this all through the API with calls up and down, just implemented a special-case CMD_BLOCK_TXQS flag for this, it's only needed in the old gen1 transport. While at it, fix a complain that lockdep would have, as we lock the cmd queue and then the TXQs in the reclaim by using spin_lock_nested(). We no longer need to disable BHs in iwl_trans_pcie_block_txq_ptrs() since it's called with them disabled already. Signed-off-by:
-
Johannes Berg authored
This causes fortify warnings when compiled against recent kernels with recent compilers, and generally is not supported in the kernel anymore. Signed-off-by:
-
Johannes Berg authored
This never returns an error and the return value is never checked anyway, so it can just be void. Signed-off-by:
-
Johannes Berg authored
Signed-off-by:
-
Johannes Berg authored
We shouldn't access the device if we don't hold a reference, and if - after locking - we see that it has no bus, we also can't do anything, in fact, pci_stop_and_remove_bus_device() will be a no-op. Signed-off-by:
-
Emmanuel Grumbach authored
This can be used by the user space when it wants to clear the data we collected so far for privacy reasons. Signed-off-by:
-
Johannes Berg authored
When there's not going to be any data in the data event, we don't need to add it at all (unlike the TX version, it has no data at all.) Also combine the tracing into a separate inline so we only call iwl_rx_trace_len() once, which also simplifies things, and lets us have a single place to later add other checks. Signed-off-by:
-
Miri Korenblit authored
EHT CQI is one of the EHT PHY capabilities. We don't support EHT CQI. The non-triggered CQI feedback bit was unset in a previous patch, but the triggered CQI feedback bit wasn't. Unset it. Fixes: 0e21ec6e ("wifi: iwlwifi: nvm: Update EHT capabilities for GL device") Signed-off-by:
-
Ilan Peer authored
For an MLO connection, the BSSID of the link used during the scanning should be used (and not the one from the default link). Signed-off-by:
-
Ilan Peer authored
If a valid link ID was provided in the scan request use it instead of picking one of the active links. Signed-off-by:
-
Vinayak Yadawad authored
Current handling of del pmksa with SSID is limited to FILS security. In the current change the del pmksa support is extended to SAE/OWE security offloads as well. For OWE/SAE offloads, the PMK is generated and cached at driver/FW, so user app needs the capability to request cache deletion based on SSID for drivers supporting SAE/OWE offload. Signed-off-by:
Vinayak Yadawad <vinayak.yadawad@broadcom.com> Link: https://msgid.link/ecdae726459e0944c377a6a6f6cb2c34d2e057d0.1701262123.git.vinayak.yadawad@broadcom.com [drop whitespace-damaged rdev_ops pointer completely, enabling tracing] Signed-off-by:
-
Dmitry Antipov authored
Prefer native jiffies-wide 'unsigned long' for the 'last_active' field of 'struct airtime_info' and introduce 'ieee80211_sta_keep_active()' for airtime check in 'ieee80211_txq_keep_active()' and 'ieee80211_sta_register_airtime()'. Signed-off-by:
Dmitry Antipov <dmantipov@yandex.ru> Reviewed-by:
Toke Høiland-Jørgensen <toke@toke.dk> Link: https://msgid.link/20231206060935.612241-1-dmantipov@yandex.ruSigned-off-by:
-
Evan Quan authored
To support the WBRF mechanism, Wifi adapters utilized in the system must register the frequencies in use (or unregister those frequencies no longer used) via the dedicated calls. So that, other drivers responding to the frequencies can take proper actions to mitigate possible interference. Co-developed-by:
Mario Limonciello <mario.limonciello@amd.com> Signed-off-by:
Evan Quan <quanliangl@hotmail.com> Signed-off-by:
Ma Jun <Jun.Ma2@amd.com> Link: https://msgid.link/20231211100630.2170152-5-Jun.Ma2@amd.comSigned-off-by:
-
Evan Quan authored
The newly added WBRF feature needs this interface for channel width calculation. Signed-off-by:
-
Johannes Berg authored
Merge the platform drivers tag for WRBF. Hans says: Immutable branch between pdx86 amd wbrf branch and wifi / amdgpu due for the v6.8 merge window platform-drivers-x86-amd-wbrf-v6.8-1: v6.7-rc1 + AMD WBRF support for merging into the wifi subsys and amdgpu driver for 6.8. Merge it so we can apply the wifi tie-in for this feature. Signed-off-by:
-
- 11 Dec, 2023 2 commits
-
-
Ma Jun authored
Due to electrical and mechanical constraints in certain platform designs there may be likely interference of relatively high-powered harmonics of the (G-)DDR memory clocks with local radio module frequency bands used by Wifi 6/6e/7. To mitigate this, AMD has introduced a mechanism that devices can use to notify active use of particular frequencies so that other devices can make relative internal adjustments as necessary to avoid this resonance. Co-developed-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Ma Jun authored
Add documentation about AMD's Wifi band RFI mitigation (WBRF) mechanism explaining the theory and how it is used. Signed-off-by:
-
- 07 Dec, 2023 5 commits
-
-
Ping-Ke Shih authored
Don't enable firmware debug mode to prevent SER flow stuck due to fail to reset payload buffer, and clear HALT_C2H_INT to avoid handling unexpected interrupt at beginning. Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20231204080751.15354-6-pkshih@realtek.com
-
Chia-Yuan Li authored
To diagnose the reason why firmware or hardware get abnormal, add to dump MAC registers related to counters and interrupt masks. With these values, people can classify problems and check if registers values are unexpected, and then correct them. However, it could possible false alarm because firmware triggers this SER event by wrong conditions that we should correct it at firmware or register settings. In field, SER might happen under special conditions, and very hard to happen again, so dump lots of registers to provide rich information to catch the problem. Signed-off-by:
Chia-Yuan Li <leo.li@realtek.com> Signed-off-by:
Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by:
-
Ping-Ke Shih authored
To activate SER (system error recovery) in firmware, we have to configure IMR to trigger interrupts, and then SER can check registers to know if it need to reset hardware or notify driver to re-configure whole settings. Signed-off-by:
-
Zong-Zhe Yang authored
Extend FW program counter dump for Wi-Fi 7 chip. They poll different addresses. Signed-off-by:
-
Zong-Zhe Yang authored
RTL8922A FW supports CRASH_TRIGGER feature from v0.34.30.0. After it, debugfs fw_crash can accept type 1 on RTL8922A to trigger firmware crash and verify L2 recovery. Besides, RTL8922A sync address offset of reserved payload engine. And, SER (system error recovery) tweaks conversion from WCPU address to indirect access address for RTL8922A. The new conversion works for all supported chips. Signed-off-by:
-
- 06 Dec, 2023 2 commits
-
-
Johannes Berg authored
This is just a collection of data and we only read it, so make it const. Signed-off-by: -
Johannes Berg authored
This function has so many arguments already, before adding yet another one, refactor it to take a struct instead. Signed-off-by:
-
- 01 Dec, 2023 14 commits
-
-
Chih-Kang Chang authored
In concurrent mode, when STA interface is scanning, it causes AP interface TX beacon on wrong channel. We modified it to scan with the operating channel when one of the interfaces is already connected. Additionally, STA interface need to stop scan when AP interface is starting to avoid TX beacon on wrong channel. Finally, AP interface need to stop TX beacon when STA interface is scanning and switching to non-OP channel,This prevent other device to get beacons on wrong channel. Signed-off-by:
Chih-Kang Chang <gary.chang@realtek.com> Signed-off-by:
-
Chih-Kang Chang authored
We add a scanning check to avoid entering IPS after ROC (remain on channel) during scanning. Additionally, When P2P scanning, the flow is `1. p2p_listen step` and `2. configure filter` and `3. p2p_scan starts` in wpas, but in kernel, cfg80211 uses another workqueue to notify driver the filter change, so sometimes we see (1 > 3 > 2), that will cause Rx filter related to scan to be cleared. Therefore, we add a scanning check when configure filter to avoid scan results to be filtered. Finally, we cancel the ROC delayed workqueue before entering ROC to avoid entering twice, which might cause leaving ROC too early. Signed-off-by:
-
Po-Hao Huang authored
The interval between sending each probe request is regulated. Before this patch, some packets are not sent out properly because of our HW limit. Extend the 6 GHz channel dwell time to cope with this. Signed-off-by:
Po-Hao Huang <phhuang@realtek.com> Signed-off-by:
-
Po-Hao Huang authored
The attempt to enter power save mode might fail if there are still beacons pending in the queue. This sometimes happens after stopping P2P GO or AP mode. Extend stop AP function and flush all beacons to resolve this. Signed-off-by:
-
Stanislaw Gruszka authored
We can run PCI/MMIO devices together with USB devices in the system. Make watchdog parameter per device to avoid situation when plugin USB device change modparam_watchdog for PCI/MMIO device. Signed-off-by:
Stanislaw Gruszka <stf_xl@wp.pl> Tested-by:
Shiji Yang <yangshiji66@outlook.com> Signed-off-by:
-
Ilpo Järvinen authored
Neither vendorid nor deviceid in the struct mp_adapter is used so remove them. Signed-off-by:
Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by:
-
Ilpo Järvinen authored
The rtlwifi driver comes with a number of PCI related defines that are unused and many would be provided by PCI core anyway if they'd be needed again. Similarly, the struct rtl_pci_capabilities_header is unused and no driver should come up their own way to access PCI Capabilities anyway. Remove the unused/duplicated PCI related defines and struct. Signed-off-by:
-
Ilpo Järvinen authored
_rtl8821ae_clear_pci_pme_status() accesses the upper byte of the Power Management Control/Status register (PMCS) with literal 5 offset. Access the entire PMCS register using defines from pci_regs.h to improve code readability. While at it, remove the obvious comment and tweak debug prints slightly to not sound misleading. Signed-off-by:
-
Ilpo Järvinen authored
Add local variable pdev to shorten rtlpci->pdev. Signed-off-by:
-
Ilpo Järvinen authored
Instead of open coding the capability structure search, find the PM Capability using pci_find_capability(). While at it, rename the generic 'cap_pointer' to 'pm_cap' which makes the intent of the code more obvious. Signed-off-by:
-
Ilpo Järvinen authored
Check if PM Capability does not exists and return early which follows the usual error handling pattern. Signed-off-by:
-
Ilpo Järvinen authored
BIT(7) (PME_Status) is first checked and then set unnecessarily. Remove the unnecessary setting for the bit that is already on and adjust the comment related to it. Signed-off-by:
-
Ilpo Järvinen authored
The rtlwifi driver accesses PCIe capabilities through custom config offsets. Convert the accesses to use the normal PCIe capability accessors. Signed-off-by:
-
Ilpo Järvinen authored
The rtlwifi driver comes with custom code to write into PCIe Link Control register. RMW access for the Link Control register requires locking that is already provided by the standard PCIe capability accessors. Convert the custom RMW code writing into LNKCTL register to standard RMW capability accessors. The accesses are changed to cover the full LNKCTL register instead of touching just a single byte of the register. Fixes: 0c817338 ("rtl8192ce: Add new driver") Cc: stable@vger.kernel.org Signed-off-by:
-
