- 02 Apr, 2016 19 commits
-
-
Hans de Goede authored
commit 3e71da19 upstream. bytesperline should be the bytesperline for the first plane for planar formats, not that of all planes combined. This fixes a crash in xawtv caused by the wrong bpl. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1305389Reported-and-tested-by:
Stas Sergeev <stsp@list.ru> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Hans Verkuil authored
commit b339a72e upstream. The V4L2_CID_TX_EDID_PRESENT control reports if an EDID is present. The adv7511 however still reported the EDID present after disconnecting the HDMI cable. Fix the logic regarding this control. And when the EDID is disconnected also call ADV7511_EDID_DETECT to notify the bridge driver. This was also missing. Signed-off-by:
-
Julia Lawall authored
commit 1b669e71 upstream. & is no longer allowed in column 0, since Coccinelle 1.0.4. Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Tested-by:
Nishanth Menon <nm@ti.com> Signed-off-by:
Michal Marek <mmarek@suse.com> Signed-off-by:
-
Benjamin Tissoires authored
commit 4392bf33 upstream. hid_ignore_special_drivers works fine until hid_scan_report autodetects and reassign devices (for hid-multitouch, hid-microsoft and hid-rmi). Simplify the handling of the parameter: if it is there, use hid-generic, no matter what, and if not, scan the device or rely on the hid_have_special_driver table. This was detected while trying to disable hid-multitouch on a Surface Pro cover which prevented to use the keyboard. Signed-off-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Oliver Neukum authored
commit 264904cc upstream. Some devices I got show an inability to operate right after power on if they are already connected. They are beyond recovery if the descriptors are requested multiple times. So in case of a timeout we rather bail early and reset again. But it must be done only on the first loop lest we get into a reset/time out spiral that can be overcome with a retry. This patch is a rework of a patch that fell through the cracks. http://www.spinics.net/lists/linux-usb/msg103263.htmlSigned-off-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Lior Amsalem authored
commit b3a7f31e upstream. The Armada 375 has the same SATA IP as Armada 370 and Armada XP, which requires the PHY speed to be set in the LP_PHY_CTL register for SATA hotplug to work. Therefore, this commit updates the compatible string used to describe the SATA IP in Armada 375 from marvell,orion-sata to marvell,armada-370-sata. Fixes: 4de59085 ("ARM: mvebu: add Device Tree description of the Armada 375 SoC") Signed-off-by:
Lior Amsalem <alior@marvell.com> Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
-
Kamal Mostafa authored
commit 50fe6dd1 upstream. Use the local uapi headers to keep in sync with "recently" added #define's (e.g. VSS_OP_REGISTER1). Fixes: 3eb2094c ("Adding makefile for tools/hv") Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Signed-off-by:
-
Spencer E. Olson authored
commit 1fd24a47 upstream. This fixes a bug in function ni_tio_input_inttrig(). The trigger number should be compared to cmd->start_arg, not cmd->start_src. Fixes: 6a760394 ("staging: comedi: ni_tiocmd: clarify the cmd->start_arg validation and use") Signed-off-by:
Spencer E. Olson <olsonse@umich.edu> Reviewed-by:
Ian Abbott <abbotti@mev.co.uk> Signed-off-by:
-
Peter Hurley authored
commit 401879c5 upstream. The N_IRDA line discipline may access the previous line discipline's closed and already-fre private data on open [1]. The tty->disc_data field _never_ refers to valid data on entry to the line discipline's open() method. Rather, the ldisc is expected to initialize that field for its own use for the lifetime of the instance (ie. from open() to close() only). [1] ================================================================== BUG: KASAN: use-after-free in irtty_open+0x422/0x550 at addr ffff8800331dd068 Read of size 4 by task a.out/13960 ============================================================================= BUG kmalloc-512 (Tainted: G B ): kasan: bad access detected ----------------------------------------------------------------------------- ... Call Trace: [<ffffffff815fa2ae>] __asan_report_load4_noabort+0x3e/0x40 mm/kasan/report.c:279 [<ffffffff836938a2>] irtty_open+0x422/0x550 drivers/net/irda/irtty-sir.c:436 [<ffffffff829f1b80>] tty_ldisc_open.isra.2+0x60/0xa0 drivers/tty/tty_ldisc.c:447 [<ffffffff829f21c0>] tty_set_ldisc+0x1a0/0x940 drivers/tty/tty_ldisc.c:567 [< inline >] tiocsetd drivers/tty/tty_io.c:2650 [<ffffffff829da49e>] tty_ioctl+0xace/0x1fd0 drivers/tty/tty_io.c:2883 [< inline >] vfs_ioctl fs/ioctl.c:43 [<ffffffff816708ac>] do_vfs_ioctl+0x57c/0xe60 fs/ioctl.c:607 [< inline >] SYSC_ioctl fs/ioctl.c:622 [<ffffffff81671204>] SyS_ioctl+0x74/0x80 fs/ioctl.c:613 [<ffffffff852a7876>] entry_SYSCALL_64_fastpath+0x16/0x7a Reported-and-tested-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Peter Hurley <peter@hurleysoftware.com> Signed-off-by:
-
Sebastian Frias authored
commit 0b41ce99 upstream. Some UART HW has a single register combining UART_DLL/UART_DLM (this was probably forgotten in the change that introduced the callbacks, commit b32b19b8) Fixes: b32b19b8 ("[SERIAL] 8250: set divisor register correctly ...") Signed-off-by:
Sebastian Frias <sf84@laposte.net> Reviewed-by:
-
Tom Lendacky authored
commit b31dde2a upstream. Use a local variable for the exported and imported state so that alignment is not an issue. On export, set a local variable from the request context and then memcpy the contents of the local variable to the export memory area. On import, memcpy the import memory area into a local variable and then use the local variable to set the request context. Signed-off-by:
Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Tom Lendacky authored
commit d1662165 upstream. Since the exported information can be exposed to user-space, instead of exporting the entire request context only export the minimum information needed. Signed-off-by:
-
Hans de Goede authored
commit 7445e45d upstream. SPC 880NC PC camera discussions: http://www.pclinuxos.com/forum/index.php/topic,135688.0.htmlReported-by:
Kikim <klucznik0@op.pl> Signed-off-by:
-
Tiffany Lin authored
commit 7df5ab87 upstream. In v4l2-compliance utility, test QUERYBUF required correct length value to go through each planar to check planar's length in multi-planar buffer type Signed-off-by:
Tiffany Lin <tiffany.lin@mediatek.com> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Peter Hurley authored
commit f33798de upstream. commit 9ce119f3 ("tty: Fix GPF in flush_to_ldisc()") fixed a GPF caused by a line discipline which does not define a receive_buf() method. However, the vt driver (and speakup driver also) pushes selection data directly to the line discipline receive_buf() method via tty_ldisc_receive_buf(). Fix the same problem in tty_ldisc_receive_buf(). Signed-off-by:
-
Tom Lendacky authored
commit 952bce97 upstream. Commit 8996eafd ("crypto: ahash - ensure statesize is non-zero") added a check to prevent ahash algorithms from successfully registering if the import and export functions were not implemented. This prevents an oops in the hash_accept function of algif_hash. This commit causes the ccp-crypto module SHA support and AES CMAC support from successfully registering and causing the ccp-crypto module load to fail because the ahash import and export functions are not implemented. Update the CCP Crypto API support to provide import and export support for ahash algorithms. Signed-off-by:
-
Dan Carpenter authored
commit 6f3508f6 upstream. dct_sel_base_off is declared as a u64 but we're only using the lower 32 bits because of a shift wrapping bug. This can possibly truncate the upper 16 bits of DctSelBaseOffset[47:26], causing us to misdecode the CS row. Fixes: c8e518d5 ('amd64_edac: Sanitize f10_get_base_addr_offset') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Cc: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com> Cc: linux-edac <linux-edac@vger.kernel.org> Link: http://lkml.kernel.org/r/20160120095451.GB19898@mwandaSigned-off-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
-
Yan, Zheng authored
commit 1f041a89 upstream. struct timespec uses 'long' to present second and nanosecond. 'long' is 64 bits on 64bits machine. ceph MDS expects time stamp to be encoded as struct ceph_timespec, which uses 'u32' to present second and nanosecond. Signed-off-by:
Yan, Zheng <zyan@redhat.com> BugLink: http://tracker.ceph.com/issues/15302 BugLink: http://bugs.launchpad.net/bugs/1564950Signed-off-by:
-
Ingo Molnar authored
commit 590ee7db upstream. Now that we are using smpboot_thread_init() in init/main.c as well, provide it for !CONFIG_SMP as well. This addresses a !CONFIG_SMP build failure. Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Borislav Petkov <bp@suse.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
- 30 Mar, 2016 1 commit
-
-
Paul E. McKenney authored
commit 00df35f9 upstream. Currently, smpboot_unpark_threads() is invoked before the incoming CPU has been added to the scheduler's runqueue structures. This might potentially cause the unparked kthread to run on the wrong CPU, since the correct CPU isn't fully set up yet. That causes a sporadic, hard to debug boot crash triggering on some systems, reported by Borislav Petkov, and bisected down to: 2a442c9c ("x86: Use common outgoing-CPU-notification code") This patch places smpboot_unpark_threads() in a CPU hotplug notifier with priority set so that these kthreads are unparked just after the CPU has been added to the runqueues. Reported-and-tested-by:
Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by:
Luis Henriques <luis.henriques@canonical.com> Signed-off-by:
-
- 29 Mar, 2016 8 commits
-
-
Oliver Neukum authored
commit 8835ba4a upstream. An attack has become available which pretends to be a quirky device circumventing normal sanity checks and crashes the kernel by an insufficient number of interfaces. This patch adds a check to the code path for quirky devices. Signed-off-by:
-
Vladis Dronov authored
commit 950336ba upstream. The ati_remote2 driver expects at least two interfaces with one endpoint each. If given malicious descriptor that specify one interface or no endpoints, it will crash in the probe function. Ensure there is at least two interfaces and one endpoint for each interface before using it. The full disclosure: http://seclists.org/bugtraq/2016/Mar/90Reported-by:
Ralf Spenneberg <ralf@spenneberg.net> Signed-off-by:
Vladis Dronov <vdronov@redhat.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Vasily Kulikov authored
commit 8a5e5e02 upstream. Poison pointer values should be small enough to find a room in non-mmap'able/hardly-mmap'able space. E.g. on x86 "poison pointer space" is located starting from 0x0. Given unprivileged users cannot mmap anything below mmap_min_addr, it should be safe to use poison pointers lower than mmap_min_addr. The current poison pointer values of LIST_POISON{1,2} might be too big for mmap_min_addr values equal or less than 1 MB (common case, e.g. Ubuntu uses only 0x10000). There is little point to use such a big value given the "poison pointer space" below 1 MB is not yet exhausted. Changing it to a smaller value solves the problem for small mmap_min_addr setups. The values are suggested by Solar Designer: http://www.openwall.com/lists/oss-security/2015/05/02/6Signed-off-by:
Vasily Kulikov <segoon@openwall.com> Cc: Solar Designer <solar@openwall.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Takashi Iwai authored
commit 447d6275 upstream. Add some sanity check codes before actually accessing the endpoint via get_endpoint() in order to avoid the invalid access through a malformed USB descriptor. Mostly just checking bNumEndpoints, but in one place (snd_microii_spdif_default_get()), the validity of iface and altsetting index is checked as well. Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=971125Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit 0f886ca1 upstream. create_fixed_stream_quirk() may cause a NULL-pointer dereference by accessing the non-existing endpoint when a USB device with a malformed USB descriptor is used. This patch avoids it simply by adding a sanity check of bNumEndpoints before the accesses. Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=971125Signed-off-by:
-
Josh Boyer authored
commit 4ec0ef3a upstream. The iowarrior driver expects at least one valid endpoint. If given malicious descriptors that specify 0 for the number of endpoints, it will crash in the probe function. Ensure there is at least one endpoint on the interface before using it. The full report of this issue can be found here: http://seclists.org/bugtraq/2016/Mar/87Reported-by:
Josh Boyer <jwboyer@fedoraproject.org> Signed-off-by:
-
Josh Boyer authored
commit 9c6ba456 upstream. The powermate driver expects at least one valid USB endpoint in its probe function. If given malicious descriptors that specify 0 for the number of endpoints, it will crash. Validate the number of endpoints on the interface before using them. The full report for this issue can be found here: http://seclists.org/bugtraq/2016/Mar/85Reported-by:
-
David S. Miller authored
commit fbd40ea0 upstream. When an inetdev is destroyed, every address assigned to the interface is removed. And in this scenerio we do two pointless things which can be very expensive if the number of assigned interfaces is large: 1) Address promotion. We are deleting all addresses, so there is no point in doing this. 2) A full nf conntrack table purge for every address. We only need to do this once, as is already caught by the existing masq_dev_notifier so masq_inet_event() can skip this. Reported-by:
Solar Designer <solar@openwall.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Tested-by:
Cyrill Gorcunov <gorcunov@openvz.org> Signed-off-by:
-
- 25 Mar, 2016 6 commits
-
-
Herbert Xu authored
commit 1822793a upstream. We need to lock the child socket in skcipher_check_key as otherwise two simultaneous calls can cause the parent socket to be freed. Signed-off-by:
-
Herbert Xu authored
commit ad46d7e3 upstream. We need to lock the child socket in hash_check_key as otherwise two simultaneous calls can cause the parent socket to be freed. Signed-off-by:
-
Herbert Xu authored
commit d7b65aee upstream. This patch removes the custom release parent function as the generic af_alg_release_parent now works for nokey sockets too. Signed-off-by:
-
Herbert Xu authored
commit f1d84af1 upstream. This patch removes the custom release parent function as the generic af_alg_release_parent now works for nokey sockets too. Signed-off-by:
-
Herbert Xu authored
commit 6e8d8ecf upstream. This patch adds an exception to the key check so that cipher_null users may continue to use algif_skcipher without setting a key. Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Herbert Xu authored
commit a1383cd8 upstream. This patch adds a way for skcipher users to determine whether a key is required by a transform. Signed-off-by:
-
- 24 Mar, 2016 3 commits
-
-
Herbert Xu authored
commit 6de62f15 upstream. Hash implementations that require a key may crash if you use them without setting a key. This patch adds the necessary checks so that if you do attempt to use them without a key that we return -ENOKEY instead of proceeding. This patch also adds a compatibility path to support old applications that do acept(2) before setkey. Signed-off-by:
-
Herbert Xu authored
commit a0fa2d03 upstream. This patch adds a compatibility path to support old applications that do acept(2) before setkey. Signed-off-by:
-
Herbert Xu authored
commit dd504589 upstream. Some cipher implementations will crash if you try to use them without calling setkey first. This patch adds a check so that the accept(2) call will fail with -ENOKEY if setkey hasn't been done on the socket yet. Reported-by:
-
- 21 Mar, 2016 1 commit
-
-
Kamal Mostafa authored
Signed-off-by:
-
- 16 Mar, 2016 2 commits
-
-
Or Gerlitz authored
commit 11d8d645 upstream. According to IBTA spec v1.3 section 12.7.19, QPs should use GRH when the path returned by the SA has hop-limit > 0. Currently, we do that only for the > 1 case, fix that. Fixes: 6d969a47 ('IB/sa: Add ib_init_ah_from_path()') Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by:
Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> [ kamal: backport to 4.2-stable: context ] Signed-off-by:
-
Benjamin Poirier authored
commit 1837b2e2 upstream. The current reserved_tailroom calculation fails to take hlen and tlen into account. skb: [__hlen__|__data____________|__tlen___|__extra__] ^ ^ head skb_end_offset In this representation, hlen + data + tlen is the size passed to alloc_skb. "extra" is the extra space made available in __alloc_skb because of rounding up by kmalloc. We can reorder the representation like so: [__hlen__|__data____________|__extra__|__tlen___] ^ ^ head skb_end_offset The maximum space available for ip headers and payload without fragmentation is min(mtu, data + extra). Therefore, reserved_tailroom = data + extra + tlen - min(mtu, data + extra) = skb_end_offset - hlen - min(mtu, skb_end_offset - hlen - tlen) = skb_tailroom - min(mtu, skb_tailroom - tlen) ; after skb_reserve(hlen) Compare the second line to the current expression: reserved_tailroom = skb_end_offset - min(mtu, skb_end_offset) and we can see that hlen and tlen are not taken into account. The min() in the third line can be expanded into: if mtu < skb_tailroom - tlen: reserved_tailroom = skb_tailroom - mtu else: reserved_tailroom = tlen Depending on hlen, tlen, mtu and the number of multicast address records, the current code may output skbs that have less tailroom than dev->needed_tailroom or it may output more skbs than needed because not all space available is used. Fixes: 4c672e4b ("ipv6: mld: fix add_grhead skb_over_panic for devs with large MTUs") Signed-off-by:
Benjamin Poirier <bpoirier@suse.com> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
