Introduce mt76_connac common mcu library for code sharing between mt7615 and
mt7921 devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce mt76_vif data structure to share common fields between
mt7615_vif and mt7921_vif and create a mcu common library
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

With a maximum length of 7991, the radio sometimes locks up under load when
transmitting A-MSDU frames to lots of stations. Using the lower limit makes
it work reliably again
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Instead of holding it for the duration of an entire station schedule run,
which can block out competing tasks for a significant amount of time,
only hold it for scheduling one batch of packets for one station.
Improves responsiveness under load
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Similar to commit '0e40dbd5 ("mt7601u: process URBs in status EPROTO
properly")', do no schedule rx_worker for urb marked with status set
-EPROTO
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Since it is global for all drivers, it belongs to the main device
Signed-off-by: Felix Fietkau <nbd@nbd.name>

The firmware treats it as global, so we need to avoid collisions here
Signed-off-by: Felix Fietkau <nbd@nbd.name>

For performance reasons, mt7915 supports using 2 PCIE gen1 links on
platforms that don't support gen2.
Add support for using this to move traffic for a second DBDC band onto
a dedicated link
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Only clear dev->phy2 after the phy is gone, the driver may still need to access
it until shutdown is complete
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This is needed for DBDC cards to work correctly on both bands simultaneously
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Reduce code duplication and remove unnecessary exports
Signed-off-by: Felix Fietkau <nbd@nbd.name>

With this patch, TxBF can be run on both bands simultaneously.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

fix semicolon.cocci warnings:
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:1694:2-3: Unneeded semicolon
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Update mcu country code running mt7615_mcu_set_channel_domain routine in
mt7615_regd_notifier().
Filter out disabled channels in mt7615_mcu_set_channel_domain().
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

When the EEPROM band fields contain default values, assign 2.4 GHz to the
first band and 5 GHz to the second.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Annotate WIFI_CONF eeprom mask values with the byte number
Fix parsing per-band number of chains
Signed-off-by: Felix Fietkau <nbd@nbd.name>

It causes high CPU load on the WA core, which can lead to extra latency when
using many stations. Dropping packets for long queues is managed by mac80211
fq_codel instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add support for passing flags for selecting the MCU target and query type
instead of trying to detect it based on the command id
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This is causing some extreme latency spikes when sending traffic to
multiple stations at the same time. Disable this until the firmware issue
is sorted out
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Without this change, the start operation could potentially race against eeprom
or txbf init
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Do not use the RSSI values of the unavailable chain
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add ht/vht implicit Tx beamforming support and enable it via debugfs.
Tested-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This is a preliminary patch for implicit beamforming support.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

When testmode can be enabled, the start() callback would already be
called, causing that txpower sku feature isn't really disabled after
testmode is enabled. This patch fix the issue.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Implement continuous tx state for MT7915 NIC testmode.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This is a preliminary patch to simplify setting state in mt7915
testmode, for adding the new continuous tx state.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Support to set a special tx state in testmode: continuous tx,
which is used for sending tx without time gap.
Note that continuous tx mode doesn't send real packets, instead, it's
pure phy signal, and the waveform can be observed by instrument.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add a testmode mcu command to clean up hw tx queue before a new
testmode tx starts.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

If tx_time is set, calculate a new packet length based on tx time and
tx rate.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add support to calculate and apply ipg parameters in testmode
for MT7915 NIC.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Split parameter settings and mcu command update in mt7915_mcu_set_tx().
This is for reusing edca update function in testmode ipg setting.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Originally, tx queued limit is set to 1000 to prevent from running out
of tx token. If a new testmode tx is triggered while the previous one
hasn't finished yet, we'll wait a period of time until tx_done equals to
tx_queued. Normally, current queued limit can finish in 10 seconds.

However, if ipg is configured to a larger value, less than 1000 packets
can be done in the default timeout period, which may lead to a crash
when a new testmode tx triggered.

To deal with this, make tx queued limit dynamically adjusted according
to ipg value.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add attributes for setting tx inter-packet gap (ipg), duty cycle, and
transmission time in testmode.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add spatial extension (spe) index as a configurable parameter in testmode.
This is used for specifically configuring TX path, such as different
WF TX priority, number of antennas and spatial streams.

If spe_idx is not set, TX path depends on tx_antenna_mask; otherwise,
both spe_idx and tx_antenna_mask are referenced to decide TX path.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

LDPC should be set when bw is larger than 20MHz to make
testmode tx work normally.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move chainmask from driver phy to mt76_phy since it is used by all
drivers. This is a preliminary patch to create a common mcu library used
by mt7615 and mt7921 drivers
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mac_work delayed_work and mac_work_count in mt76_phy since it is
used by all drivers. This is a preliminary patch to create a common mcu
library used by mt7615 and mt7921 drivers
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move per-chip testmode data to mt7615_phy, to properly support
reg_backup and rx status of each band in testmode.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move per-chip testmode data to mt7915_phy, to properly support
reg_backup and rx status of each band in testmode.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move testmode mtd variables to mt76_dev, since they are the same on
each phy.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>