- 27 Jul, 2010 40 commits
-
-
Kashyap, Desai authored
Added a new sysfs shost attribute called ioc_reset_count. This will keep count of host resets (both diagnostic and message unit). Signed-off-by:
Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by:
James Bottomley <James.Bottomley@suse.de>
-
Kashyap, Desai authored
Added support to send link resets, hard resets, enable/disable phys, and changing link rates for for expanders. This will be exported to attributes within the sas transport layer. A new wrapper function was added for sending SMP passthru to expanders for phy control. Signed-off-by:
-
Kashyap, Desai authored
Added support to retrieve the invalid_dword_count, running_disparity_error_count, loss_of_dword_sync_count, and phy_reset_problem_count for expanders. This will be exported to attributes within the sas transport layer. A new wrapper function was added for sending SMP passthru to retrieve the expander phy error log. Signed-off-by:
-
Kashyap, Desai authored
Added command line option called disable_discovery. When enabled on the command line, the driver will not send a port_enable when loaded for the first time. If port_enable is not called, then there is no discovery of devices, as well as the sas topology. Then later if one desires to invoke discovery, then they will need to issue a diagnostic reset. A diagnostic reset can be issued various ways. One of the way is throught sysfs. Signed-off-by:
-
Kashyap, Desai authored
Driver should not allow multiple host reset when already host reset is in progress. It is possible that host reset was sent by scsi mid layer while there was already an host reset active, either issued via IOCTL interface or internaly, like a config page timeout. Since there was a host reset active, the driver would return a FAILED response to the scsi mid layer. The solution is make sure pending host resets will wait for the active host reset to complete before returning control back up the call stack. Signed-off-by:
-
Kashyap, Desai authored
[SCSI] mpt2sas: Fix to use sas device list instead of enclosure list for _transpor_get_enclosure_identifier. Enclosure_identifier not being returned by mpt2sas The driver exports callback function to the sas transport layer for obtaining the enclosure logical id. This function is called _transport_get_enclosure_identifier. The driver was searching the wrong list for the enclosure_identifier. The driver should be searching the sas device list instead of enclosure list. The sas address that is passed to the driver is for the end device, not enclosure. Signed-off-by:
-
Karen Xie authored
Zero out the reserved or un-used CPL message fields to prevent any garbage value. Signed-off-by:
Karen Xie <kxie@chelsio.com> Reviewed-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
-
Stephen M. Cameron authored
Some controllers might try to tell us they support 0 commands in performant mode. This is a lie told by buggy firmware. We have to be wary of this lest we try to allocate a negative number of command blocks, which will be treated as unsigned, and get an out of memory condition. Signed-off-by:
Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by:
-
Stephen M. Cameron authored
There are things which need to be done in the intx interrupt handler which do not need to be done in the msi/msix interrupt handler, like checking that the interrupt is actually for us, and checking that the interrupt pending bit on the hardware is set (which we weren't previously doing at all, which means old controllers wouldn't work), so it makes sense to separate these into two functions. Signed-off-by:
-
Stephen M. Cameron authored
The 6402/6404 are two PCI devices -- two Smart Array controllers -- that fit into one slot. It is possible to reset them independently, however, they share a battery backed cache module. One of the pair controls the cache and the 2nd one access the cache through the first one. If you reset the one controlling the cache, the other one will not be a happy camper. So we just forbid resetting this conjoined mess. Signed-off-by:
-
Stephen M. Cameron authored
Smart Array controllers newer than the P600 do not honor the PCI power state method of resetting the controllers. Instead, in these cases we can get them to reset via the "doorbell" register. This escaped notice until we began using "performant" mode because the fact that the controllers did not reset did not normally impede subsequent operation, and so things generally appeared to "work". Once the performant mode code was added, if the controller does not reset, it remains in performant mode. The code immediately after the reset presumes the controller is in "simple" mode (which previously, it had remained in simple mode the whole time). If the controller remains in performant mode any code which presumes it is in simple mode will not work. So the reset needs to be fixed. Unfortunately there are some controllers which cannot be reset by either method. (eg. p800). We detect these cases by noticing that the controller seems to remain in performant mode even after a reset has been attempted. In those case, we proceed anyway, as if the reset has happened (and skip the step of waiting for the controller to become ready -- which is expecting it to be in "simple" mode.) To sum up, we try to do a better job of resetting the controller if "reset_devices" is set, and if it doesn't work, we print a message and try to continue anyway. Signed-off-by:
-
Stephen M. Cameron authored
for kdump support Signed-off-by:
-
Stephen M. Cameron authored
Rationale for this is that I will also need to use this code in fixing kdump host reset code prior to having the hba structure. Signed-off-by:
-
Stephen M. Cameron authored
Rationale for this is that in order to fix the hard reset code used by kdump, we need to use this function before we even have the per HBA structure. Signed-off-by:
-
Stephen M. Cameron authored
We were previously only accepting HP boards. Signed-off-by:
-
Stephen M. Cameron authored
Add 5 CCISSE smart array controllers Signed-off-by:
-
Nick Cheng authored
[SCSI] arcmsr: Support 1024 scatter-gather list entries and improve AP while FW trapped and behaviors of EHs 1. To support 4M/1024 scatter-gather list entry, reorganize struct ARCMSR_CDB and struct CommandControlBlock 2. To modify arcmsr_probe 3. In order to help fix F/W issue, add the driver mode for type B card 4. To improve AP's behavior while F/W resets 5. To unify struct MessageUnit_B's members' naming in all OS drivers' 6. To improve error handlers, arcmsr_bus_reset(), arcmsr_abort() 7. To fix the arcmsr_queue_command() in bus reset stage, just let the commands pass down to FW, don't block Signed-off-by:
Nick Cheng <nick.cheng@areca.com.tw> Signed-off-by:
-
Joe Eykholt authored
Remote ports were restarting indefinitely after getting rejects in PRLI. Fix by adding a counter of restarts and limiting that with the port login retry limit as well. Signed-off-by:
Joe Eykholt <jeykholt@cisco.com> Signed-off-by:
Robert Love <robert.w.love@intel.com> Signed-off-by:
-
Joe Eykholt authored
This patch somewhat combines two fixes to remote port handing in libfc. The first problem was that rport work could be queued on a deleted and freed rport. This is handled by not resetting rdata->event ton NONE if the rdata is about to be deleted. However, that fix led to the second problem, described by Bhanu Gollapudi, as follows: > Here is the sequence of events. T1 is first LOGO receive thread, T2 is > fc_rport_work() scheduled by T1 and T3 is second LOGO receive thread and > T4 is fc_rport_work scheduled by T3. > > 1. (T1)Received 1st LOGO in state Ready > 2. (T1)Delete port & enter to RESTART state. > 3. (T1)schdule event_work, since event is RPORT_EV_NONE. > 4. (T1)set event = RPORT_EV_LOGO > 5. (T1)Enter RESTART state as disc_id is set. > 6. (T2)remember to PLOGI, and set event = RPORT_EV_NONE > 6. (T3)Received 2nd LOGO > 7. (T3)Delete Port & enter to RESTART state. > 8. (T3)schedule event_work, since event is RPORT_EV_NONE. > 9. (T3)Enter RESTART state as disc_id is set. > 9. (T3)set event = RPORT_EV_LOGO > 10.(T2)work restart, enter PLOGI state and issues PLOGI > 11.(T4)Since state is not RESTART anymore, restart is not set, and the > event is not reset to RPORT_EV_NONE. (current event is RPORT_EV_LOGO). > 12. Now, PLOGI succeeds and fc_rport_enter_ready() will not schedule > event_work, and hence the rport will never be created, eventually losing > the target after dev_loss_tmo. So, the problem here is that we were tracking the desire for the rport be restarted by state RESTART, which was otherwise equivalent to DELETE. A contributing factor is that we dropped the lock between steps 6 and 10 in thread T2, which allows the state to change, and we didn't completely re-evaluate then. This is hopefully corrected by the following minor redesign: Simplify the rport restart logic by making the decision to restart after deleting the transport rport. That decision is based on a new STARTED flag that indicates fc_rport_login() has been called and fc_rport_logoff() has not been called since then. This replaces the need for the RESTART state. Only restart if the rdata is still in DELETED state and only if it still has the STARTED flag set. Also now, since we clear the event code much later in the work thread, allow for the possibility that the rport may have become READY again via incoming PLOGI, and if so, queue another event to handle that. In the problem scenario, the second LOGO received will cause the LOGO event to occur again. Reported-by:
Bhanu Gollapudi <bprakash@broadcom.com> Signed-off-by:
-
Roel Kluin authored
In fnic_abort_cmd() and fnic_device_reset() assign `rport' earlier to make FNIC_SCSI_DBG() calls cleaner. In fnic_clean_pending_aborts() `rport' is not used. Signed-off-by:
Roel Kluin <roel.kluin@gmail.com> Acked-by:
Abhijeet Joglekar <abjoglek@cisco.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Yi Zou authored
lport state is enum not bit mask. Signed-off-by:
Yi Zou <yi.zou@intel.com> Signed-off-by:
-
Bhanu Prakash Gollapudi authored
As per FC-BB-5 rev.2, section 7.8.7.1, strict ordering of FIP descriptors is required for ELS requests. Also, look for missing and duplicate critical descriptors. Signed-off-by:
-
Bhanu Prakash Gollapudi authored
Clear virtual link for NPIV ports is now handled by resetting the matching vnport. Signed-off-by:
-
Bhanu Prakash Gollapudi authored
As per FC-BB-5 rev 2, section 7.8.6.2, malformed FIP frame shall be discarded. Drop discovery adv, ELS and CLV's with duplicate critical descriptors. [Resending after incorporating Joe's review comments] Signed-off-by:
-
Joe Eykholt authored
Allow the D flag (indicating that keep-alives are not needed) to be updated dynamically from received FIP advertisements. Signed-off-by:
-
Joe Eykholt authored
keep alives are disabled due to fd_flags set and also stop updating keep alive values in that case. Update select fcf time only if fcf is not already selected or select time is not already determined from parse adv, and then have select time cleared only once after fcf is selected. Changed deadline check to time_after_eq() from time_after() since now next timeout will be on exact 2.5 times FKA followed by first advertisement. Signed-off-by:
Vasu Dev <vasu.dev@intel.com> Signed-off-by:
-
Joe Eykholt authored
[This patch has several improvements to the code in the fip timers. It hasn't been tested yet. I'm sending it out for review. Vasu, perhaps you can merge this with your patch and test it together.] The current code allows an advertisement to be used even if it has been 3 times the FCF keep-alive advertisement period (FKA) since one was received from that FCF. The spec. calls for 2.5 times FKA. Fix this and make sure we detect missed keep-alives promptly. Signed-off-by:
-
Bhanu Prakash Gollapudi authored
Resubmitting after incorporating Joe's review comment. Unsolicited PRLO request is now handled by sending LS_ACC, and then relogin to the remote port if an N-port login session exists for that remote port. Note that this patch should be applied on top of Joe Eykholt's "Fix remote port restart problem" patch. Signed-off-by:
-
Joe Eykholt authored
Some old comments in fc_fcoe.h say TBD long after the standard has been passed by T11. Clean them up. Signed-off-by:
-
Bhanu Prakash Gollapudi authored
As per FC-LS Rev 1.62 table 46, response codes are handled as follows: 1. If the Req executed is true, PRLI is accepted. 2. If Req executed is not set, if resp code is 5, PRLI is not retried and port is logged out. 3. If resp code is anything apart from 1 or 5, PRLI is retired upto max retry count. Signed-off-by:
-
Bhanu Prakash Gollapudi authored
Retry upto max_rport_retry_count when a target responds with LS_RJT for a PRLI request. Signed-off-by:
-
Bhanu Prakash Gollapudi authored
Host does not send discovery solicitation messages if Disc. Adv from FCF are dropped. It restarts sending solicitation only after receiving a Discovery Adv. from FCF. Fix is to restart solicitation immediately after CVL processing. Signed-off-by:
-
Bhanu Prakash Gollapudi authored
Avoid infinite loop while processing FIP ELS or discovery advertisement with non-critical descriptors. Signed-off-by:
-
Joe Eykholt authored
A check in fcoe_ctlr_send_keep_alive() returns if there's no port_id for the local port. This could miss a keep alive if we just did a host reset and have logged off and will log back in. Return only if we are doing the port keep alive, in which case we need to be logged in. Signed-off-by:
-
Wayne Boyer authored
A problem was found where the call to scsi_add_device() fails intermittently for an adapter. This is caused when __scsi_add_device() returns -ENODEV as a result of not calling scsi_probe_and_add_lun() since the call to scsi_host_scan_allowed() fails. scsi_host_scan_allowed() fails because the adapter state is set to SHOST_RECOVERY instead of SHOST_RUNNING. The state of the adapter is being set to SHOST_RECOVERY by scsi_eh_scmd_add() during error handling. This problem is avoided by moving the setting of the allow_restart flag to later in the device initialization sequence. This prevents further error handling if we get a NOT_READY response from a TUR command by causing scsi_check_sense() to return SUCCESS. Therefore, scsi_eh_scmd_add() will not run and the adapter state will remain as SHOST_RUNNING. Signed-off-by:
Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
-
Dan Carpenter authored
"phba" is always null here so we can't dereference it. Signed-off-by:
Dan Carpenter <error27@gmail.com> Reviewed-by:
-
Dan Carpenter authored
I added a kfree(pwrb_arr) in front of the return. Signed-off-by:
-
Wayne Boyer authored
Compiling the driver will fail on 32 bit powerpc and other architectures where writeq is not defined. This patch adds a definition for writeq. Signed-off-by:
-
Mike Christie authored
This patch fixes 4 bugs in the connection connect/disconnect cleanup path. 1. If beiscsi_open_conn fails beiscsi_free_ep was always being called, and if beiscsi_open_conn failed because beiscsi_get_cid failed then we would free an unallocated cid. 2. If beiscsi_ep_connect failed due to a beiscsi_open_conn failure it was leaking iscsi_endpoints. 3. beiscsi_ep_disconnect was leaking iscsi_endpoints. beiscsi_ep_disconnect should free the iscsi_endpoint. We cannot do it in beiscsi_conn_stop because that is only called for iscsi connection cleanup. If beiscsi_ep_connect returns success, but then the poll function fails or the connect times out then beiscsi_ep_disconnect will be called to clean up the ep. The conn_stop callout will not be called in that path. 4. beiscsi_conn_stop was freeing the iscsi_endpoint then accessing it a couple lines later. Signed-off-by:
-
James Smart authored
Signed-off-by:
Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by:
James Smart <james.smart@emulex.com> Signed-off-by:
-
