In code comments, use Tx|Rx instead of tx|rx
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

1. Fix several cases of double spacing
2. Fix typos
3. Capitalize abbreviations
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Function signatures that do not exceed 80-characters should be on a single
line.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Clean up number of formatting issues and a comment that could use
clarification.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice_napi_poll is hard-coded to return zero when it's done. It should
instead return the work done (if any work was done). The only time it
should return zero is if an interrupt or poll is handled and no work
is performed. So change the return value to be the minimum of work
done or budget-1.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Indicate these structs should not be modified and take advantage of some
compiler optimizations by making these structs const.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In the action fields for a MAC-VLAN filter, do not set the LAN_EN flag
if the MAC in the MAC-VLAN is unicast MAC. The unicast packets that
match should not be forwarded to the wire.
Signed-off-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Added check of return value for ice_init_def_sw_recp().
Now we know if memory was correctly allocated.
Signed-off-by: Jaroslaw Ilgiewicz <jaroslaw.ilgiewicz@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

1. Assigning the register offset and mask values contains duplicate code
   that can easily be replaced with a macro.

2. Separate functions for freeing send queue and receive queue rings are
   not needed; replace with a single function that uses a pointer to the
   struct ice_ctl_q_ring structure as a parameter instead of a pointer to
   the struct ice_ctl_q_info structure.

3. Initializing register settings for both send queue and receive queue
   contains duplicate code that can easily be replaced with a helper
   function.

4. Separate functions for freeing send queue and receive queue buffers are
   not needed; duplicate code can easily be replaced with a macro.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If VSI state is up, we should do autoneg with link up, otherwise
with link down.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In rx_alloc_pkts(), there is a loop call of tasklet, which causes
100% cpu utilization, even no packets are being received. This patch
fixes this bug.
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In add_mac_addr(), if the MAC address is a muliticast address,
it will not be set, which causes the network card fail to receive
the multicast packet. This patch fixes this bug.
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to improve performance, this patch adds rx checksum offload
for the HiNIC driver. Performance test(Iperf) shows more than 80%
improvement in TCP streams.
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To improve performance, this patch uses bit operations to replace
multiply and division operators.
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend cooling device with cooling levels vector to allow more
flexibility of PWM setting.

Thermal zone algorithm operates with the numerical states for PWM
setting. Each state is the index, defined in range from 0 to 10 and it's
mapped to the relevant duty cycle value, which is written to PWM
controller. With the current definition fan speed is set to 0% for state
0, 10% for state 1, and so on up to 100% for the maximum state 10.

Some systems have limitation for the PWM speed minimum. For such systems
PWM setting speed to 0% will just disable the ability to increase speed
anymore and such device will be stall on zero speed.  Cooling levels
allow to configure state vector according to the particular system
requirements. For example, if PWM speed is not allowed to be below 30%,
cooling levels could be configured as 30%, 30%, 30%, 30%, 40%, 50% and
so on.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Null pointer dereference seen when cxgb4vf driver is unloaded
without bringing up any interfaces, moving mac_hlist initialization
to driver probe and free the mac_hlist in remove to fix the issue.

Fixes: 24357e06 ("cxgb4vf: fix memleak in mac_hlist initialization")
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Under stress, softirq rx handler often hits a socket owned by the user,
and has to queue the packet into socket backlog.

When this happens, skb dst refcount is taken before we escape rcu
protected region. This is done from __sk_add_backlog() calling
skb_dst_force().

Consumer will have to perform the opposite costly operation.

AFAIK nothing in tcp stack requests the dst after skb was stored
in the backlog. If this was the case, we would have had failures
already since skb_dst_force() can end up clearing skb dst anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This has no value whatsoever.
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two cases were we can avoid calling ktime_get_ns() :

1) Queue is empty.
2) Internal queue is not empty.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
gred: add offload support

This series adds support for GRED offload in the nfp driver.  So
far we have only supported the RED Qdisc offload, but we need a
way to differentiate traffic types e.g. based on DSCP marking.

It may seem like PRIO+RED is a good match for this job, however,
(a) we don't need strict priority behaviour of PRIO, and (b) PRIO
uses the legacy way of mapping ToS fields to bands, which is quite
awkward and limitting.

The less commonly used GRED Qdisc is a better much for the scenario,
it allows multiple sets of RED parameters and queue lengths to be
maintained with a single FIFO queue.  This is exactly how nfp offload
behaves.  We use a trivial u32 classifier to assign packets to virtual
queues.

There is also the minor advantage that GRED can't have its child
changed, therefore limitting ways in which the configuration of SW
path can diverge from HW offload.

Last patch of the series adds support for (G)RED in non-ECN mode,
where packets are dropped instead of marked.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Original FW only allowed us to perform ECN marking.  Newer releases
also support plain old drop.  Add the ability to configure drop
policy.  This is particularly useful in combination with GRED,
because different bands can have different ECN marking setting.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use offload of very simple u32 filters to direct packets to GRED
bands based on the DSCP marking.  No u32 hashing is supported,
just plain simple filters matching on ToS or Priority with
appropriate mask device can support.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Learn how to set the DSCP map.  FW uses a packed array which
geometry depends on the number of supported priorities and
virtual queues.  Write code to assemble this map and to communicate
the setting to the FW via mailbox.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for PRIO offload calculate how long the prio map
for FW will be and make sure the configuration can be performed
via the vNIC mailbox.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of egress offloads the class/flowid assigned by the filter
may be very important for offloaded Qdisc selection.  Provide this
info to drivers.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for GRED offload.  It behaves much like RED, but
can apply different parameters to different bands.  GRED operates
pretty much exactly like our HW/FW with a single FIFO and different
RED state instances.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Wrap RED parameters and stats into a structure, and a 1-element
array.  Upcoming GRED offload will add the support for more bands.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow drivers which offload GRED to report back statistics.  Since
A lot of GRED stats is fairly ad hoc in nature pass to drivers the
standard struct gnet_stats_basic/gnet_stats_queue pairs, and
untangle the values in the core.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add basic offload for the GRED Qdisc.  Inform the drivers any
time Qdisc or virtual queue configuration changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add up stats for all bands for the extra ethtool statistics.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In PRIO-enabled FW read the statistics from per-band symbol, rather
than from the standard per-PCIe-queue counters.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure the threshold table is large enough to hold information
for all bands.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for per-band RED offload pass band parameter to
functions.  For now it will always be 0.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for multi-band RED offload if FW is capable map
the extended symbols which will allow us to set per-band parameters
and read stats.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before setting tm related configuration to hardware, driver
needs to check the configuration provided by user is valid.
Currently hclge_ieee_setets and hclge_setup_tc both implement
their own checking, which has a lot in common.

This patch addes hclge_dcb_common_validate to do the common
checking. The checking in hclge_tm_prio_tc_info_update
and hclge_tm_schd_info_update is unnecessary now, so change
the return type to void, which removes the need to do error
handling when one of the checking fails.

Also, ets->prio_tc is indexed by user prio and ets->tc_tsa is
indexed by tc num, so this patch changes them to use different
index.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
selftests: Add tests for VXLAN at an 802.1d bridge

Petr says:

This patchset adds several tests for VXLAN attached to an 802.1d bridge
and fixes a related bug.

First patch #1 fixes a bug in propagating SKB already-forwarded marks
over veth to bridges, where they are irrelevant. This bug causes the
vxlan_bridge_1d test suite from this patchset to fail as the packets
aren't forwarded by br2.

In patches #2 and #3, lib.sh is extended to support network namespaces.
The use of namespaces is necessitated by VXLAN, which allows only one
VXLAN device with a given VNI per namespace. Thus to host full topology
on a single box for selftests, the "remote" endpoints need to be in
namespaces.

In patches #4-#6, lib.sh is extended in other ways to facilitate the
following patches.

In patches #7-#15, first the skeleton, and later the generic tests
themselves are added.

Patch #16 then adds another test that serves as a wrapper around the
previous one, and runs it with a non-default port number.

Patches #17 and #18 add mlxsw-specific tests. About those, Ido writes:

The first test creates various configurations with regards to the VxLAN
and bridge devices and makes sure the driver correctly forbids
unsupported configuration and permits supported ones. It also verifies
that the driver correctly sets the offload indication on FDB entries and
the local route used for VxLAN decapsulation.

The second test verifies that the driver correctly configures the singly
linked list used to flood BUM traffic and that traffic is flooded as
expected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The device stores flood records in a singly linked list where each
record stores up to three IPv4 addresses of remote VTEPs. The test
verifies that packets are correctly flooded in various cases such as
deletion of a record in the middle of the list.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test various aspects of VxLAN offloading which are specific to mlxsw,
such as sanitization of invalid configurations and offload indication.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This simple wrapper reruns the VXLAN ping test with a port number of
8472.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test that when decapsulating from VXLAN, the values of inner and outer
TOS are handled appropriately. Because VXLAN driver on its own won't
produce the arbitrary TOS combinations necessary to test this feature,
simply open-code a single ICMP packet and have mausezahn assemble it.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>