The CMO op macros initially used lower case, as the original iteration
of the ALT_CMO_OP alternative stringified the first parameter to
finalise the assembly for the standard variant.
As a knock-on, the T-Head versions of these CMOs had to use mixed case
defines. Commit dd23e953 ("RISC-V: replace cbom instructions with
an insn-def") removed the asm construction with stringify, replacing it
an insn-def macro, rending the lower-case surplus to requirements.
As far as I can tell from a brief check, CBO_zero does not see similar
use and didn't require the mixed case define in the first place.
Replace the lower case characters now for consistency with other
insn-def macros in the standard and T-Head forms, and adjust the
callsites.
Suggested-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20230915-aloe-dollar-994937477776@spudSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

If misaligned_access_speed percpu var isn't so called "HWPROBE
MISALIGNED UNKNOWN", it means the probe has happened(this is possible
for example, hotplug off then hotplug on one cpu), and the percpu var
has been set, don't probe again in this case.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Fixes: 584ea656 ("RISC-V: Probe for unaligned access speed")
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230912154040.3306-1-jszhang@kernel.orgSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

If these config not set, mmc can't run for jh7110, rootfs can't
be found when using SD card. So set CONFIG_MMC_DW=y like arm64
defconfig, and set CONFIG_MMC_DW_STARFIVE=y for starfive. Then
starfive vf2 board can start SD card rootfs with mainline defconfig
and dtb.
Signed-off-by: Jinyu Tang <tangjinyu@tinylab.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230912133128.5247-1-tangjinyu@tinylab.orgSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

In the current riscv implementation, blocking syscalls like read() may
not correctly restart after being interrupted by ptrace. This problem
arises when the syscall restart process in arch_do_signal_or_restart()
is bypassed due to changes to the regs->cause register, such as an
ebreak instruction.

Steps to reproduce:
1. Interrupt the tracee process with PTRACE_SEIZE & PTRACE_INTERRUPT.
2. Backup original registers and instruction at new_pc.
3. Change pc to new_pc, and inject an instruction (like ebreak) to this
   address.
4. Resume with PTRACE_CONT and wait for the process to stop again after
   executing ebreak.
5. Restore original registers and instructions, and detach from the
   tracee process.
6. Now the read() syscall in tracee will return -1 with errno set to
   ERESTARTSYS.

Specifically, during an interrupt, the regs->cause changes from
EXC_SYSCALL to EXC_BREAKPOINT due to the injected ebreak, which is
inaccessible via ptrace so we cannot restore it. This alteration breaks
the syscall restart condition and ends the read() syscall with an
ERESTARTSYS error. According to include/linux/errno.h, it should never
be seen by user programs. X86 can avoid this issue as it checks the
syscall condition using a register (orig_ax) exposed to user space.
Arm64 handles syscall restart before calling get_signal, where it could
be paused and inspected by ptrace/debugger.

This patch adjusts the riscv implementation to arm64 style, which also
checks syscall using a kernel register (syscallno). It ensures the
syscall restart process is not bypassed when changes to the cause
register occur, providing more consistent behavior across various
architectures.

For a simplified reproduction program, feel free to visit:
https://github.com/ancientmodern/riscv-ptrace-bug-demo.
Signed-off-by: Haorong Lu <ancientmodern4@gmail.com>
Link: https://lore.kernel.org/r/20230803224458.4156006-1-ancientmodern4@gmail.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Clément Léger <cleger@rivosinc.com> says:

Since commit 61cadb9 ("Provide new description of misaligned load/store
behavior compatible with privileged architecture.") in the RISC-V ISA
manual, it is stated that misaligned load/store might not be supported.
However, the RISC-V kernel uABI describes that misaligned accesses are
supported. In order to support that, this series adds support for S-mode
handling of misaligned accesses as well support for prctl(PR_UNALIGN).

Handling misaligned access in kernel allows for a finer grain control
of the misaligned accesses behavior, and thanks to the prctl() call,
can allow disabling misaligned access emulation to generate SIGBUS. User
space can then optimize its software by removing such access based on
SIGBUS generation.

This series is useful when using a SBI implementation that does not
handle misaligned traps as well as detecting misaligned accesses
generated by userspace application using the prctrl(PR_SET_UNALIGN)
feature.

This series can be tested using the spike simulator[1] and a modified
openSBI version[2] which allows to always delegate misaligned load/store to
S-mode. A test[3] that exercise various instructions/registers can be
executed to verify the unaligned access support.

[1] https://github.com/riscv-software-src/riscv-isa-sim
[2] https://github.com/rivosinc/opensbi/tree/dev/cleger/no_misaligned
[3] https://github.com/clementleger/unaligned_test

* b4-shazam-merge:
  riscv: add support for PR_SET_UNALIGN and PR_GET_UNALIGN
  riscv: report misaligned accesses emulation to hwprobe
  riscv: annotate check_unaligned_access_boot_cpu() with __init
  riscv: add support for sysctl unaligned_enabled control
  riscv: add floating point insn support to misaligned access emulation
  riscv: report perf event for misaligned fault
  riscv: add support for misaligned trap handling in S-mode
  riscv: remove unused functions in traps_misaligned.c

Link: https://lore.kernel.org/r/20231004151405.521596-1-cleger@rivosinc.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

A hwprobe pair key is signed, but the hwprobe vDSO function was
only checking that the upper bound was valid. In order to help
avoid this type of problem in the future, and in anticipation of
this check becoming more complicated with sparse keys, introduce
and use a "key is valid" predicate function for the check.

Fixes: aa5af0aa ("RISC-V: Add hwprobe vDSO function and data")
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Evan Green <evan@rivosinc.com>
Link: https://lore.kernel.org/r/20231010165101.14942-2-ajones@ventanamicro.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Enable the configs required by the below IP blocks which are
present on RZ/Five SoC:
* ADC
* CANFD
* DMAC
* eMMC/SDHI
* OSTM
* RAVB (+ Micrel PHY)
* RIIC
* RSPI
* SSI (Sound+WM8978 codec)
* Thermal
* USB (PHY/RESET/OTG)

Along with the above some core configs are enabled too,
-> CPU frequency scaling as RZ/Five does support this.
-> MTD is enabled as RSPI can be connected to flash chips
-> Enabled I2C chardev so that it enables userspace to read/write
   i2c devices (similar to arm64)
-> Thermal configs as RZ/Five SoC does have thermal unit
-> GPIO regulator as we might have IP blocks for which voltage
   levels are controlled by GPIOs
-> OTG configs as RZ/Five USB can support host/function
-> Gadget configs so that we can test USB function (as done in arm64
   all the gadget configs are enabled)
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230929000704.53217-6-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Sami Tolvanen <samitolvanen@google.com> says:

This series adds Shadow Call Stack (SCS) support for RISC-V. SCS
uses compiler instrumentation to store return addresses in a
separate shadow stack to protect them against accidental or
malicious overwrites. More information about SCS can be found
here:

  https://clang.llvm.org/docs/ShadowCallStack.html

Patch 1 is from Deepak, and it simplifies VMAP_STACK overflow
handling by adding support for accessing per-CPU variables
directly in assembly. The patch is included in this series to
make IRQ stack switching cleaner with SCS, and I've simply
rebased it and fixed a couple of minor issues. Patch 2 uses this
functionality to clean up the stack switching by moving duplicate
code into a single function. On RISC-V, the compiler uses the
gp register for storing the current shadow call stack pointer,
which is incompatible with global pointer relaxation. Patch 3
moves global pointer loading into a macro that can be easily
disabled with SCS. Patch 4 implements SCS register loading and
switching, and allows the feature to be enabled, and patch 5 adds
separate per-CPU IRQ shadow call stacks when CONFIG_IRQ_STACKS is
enabled. Patch 6 fixes the backward-edge CFI test in lkdtm for
RISC-V.

Note that this series requires Clang 17. Earlier Clang versions
support SCS on RISC-V, but use the x18 register instead of gp,
which isn't ideal. gcc has SCS support for arm64, but I'm not
aware of plans to support RISC-V. Once the Zicfiss extension is
ratified, it's probably preferable to use hardware-backed shadow
stacks instead of SCS on hardware that supports the extension,
and we may want to consider implementing CONFIG_DYNAMIC_SCS to
patch between the implementation at runtime (similarly to the
arm64 implementation, which switches to SCS when hardware PAC
support isn't available).

* b4-shazam-merge:
  lkdtm: Fix CFI_BACKWARD on RISC-V
  riscv: Use separate IRQ shadow call stacks
  riscv: Implement Shadow Call Stack
  riscv: Move global pointer loading to a macro
  riscv: Deduplicate IRQ stack switching
  riscv: VMAP_STACK overflow detection thread-safe

Link: https://lore.kernel.org/r/20230927224757.1154247-8-samitolvanen@google.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

This fixes an encoding issue with T-Head's dcache.cva and fixes the
comment about the T-Head encodings.  The first of these was a fix and
got picked up earlier, I'm merging the second on top of it as they touch
the same comment.

* b4-shazam-merge:
  riscv: errata: prefix T-Head mnemonics with th.
  riscv: errata: fix T-Head dcache.cva encoding

Link: https://lore.kernel.org/r/20230827090813.1353-1-jszhang@kernel.orgSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

T-Head now maintains some specification for their extended instructions
at [1], in which all instructions are prefixed "th.".

Follow this practice in the kernel comments.

Link: https://github.com/T-head-Semi/thead-extension-spec [1]
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Now that trap support is ready to handle misalignment errors in S-mode,
allow the user to control the behavior of misaligned accesses using
prctl(PR_SET_UNALIGN). Add an align_ctl flag in thread_struct which
will be used to determine if we should SIGBUS the process or not on
such fault.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/r/20231004151405.521596-9-cleger@rivosinc.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

hwprobe provides a way to report if misaligned access are emulated. In
order to correctly populate that feature, we can check if it actually
traps when doing a misaligned access. This can be checked using an
exception table entry which will actually be used when a misaligned
access is done from kernel mode.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Link: https://lore.kernel.org/r/20231004151405.521596-8-cleger@rivosinc.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

This function is solely called as an initcall, thus annotate it with
__init.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Evan Green <evan@rivosinc.com>
Link: https://lore.kernel.org/r/20231004151405.521596-7-cleger@rivosinc.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

This sysctl tuning option allows the user to disable misaligned access
handling globally on the system. This will also be used by misaligned
detection code to temporarily disable misaligned access handling.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/r/20231004151405.521596-6-cleger@rivosinc.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

This support is partially based of openSBI misaligned emulation floating
point instruction support. It provides support for the existing
floating point instructions (both for 32/64 bits as well as compressed
ones). Since floating point registers are not part of the pt_regs
struct, we need to modify them directly using some assembly. We also
dirty the pt_regs status in case we modify them to be sure context
switch will save FP state. With this support, Linux is on par with
openSBI support.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Link: https://lore.kernel.org/r/20231004151405.521596-5-cleger@rivosinc.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Add missing calls to account for misaligned fault event using
perf_sw_event().
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/r/20231004151405.521596-4-cleger@rivosinc.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Misalignment trap handling is only supported for M-mode and uses direct
accesses to user memory. In S-mode, when handling usermode fault, this
requires to use the get_user()/put_user() accessors. Implement
load_u8(), store_u8() and get_insn() using these accessors for
userspace and direct text access for kernel.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/r/20231004151405.521596-3-cleger@rivosinc.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Replace macros by the only two function calls that are done from this
file, store_u8() and load_u8().
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Link: https://lore.kernel.org/r/20231004151405.521596-2-cleger@rivosinc.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Sunil V L <sunilvl@ventanamicro.com> says:

This series is a set of patches which were originally part of RFC v1 series
[1] to add ACPI support in RISC-V interrupt controllers. Since these
patches are independent of the interrupt controllers, creating this new
series which helps to merge instead of waiting for big series.

This set of patches primarily adds support below ECR [2] which is approved
by the ASWG and adds below features.

- Get CBO block sizes from RHCT on ACPI based systems.

Additionally, the series contains a patch to improve acpi_os_ioremap().

[1] - https://lore.kernel.org/lkml/20230803175202.3173957-1-sunilvl@ventanamicro.com/
[2] - https://drive.google.com/file/d/1sKbOa8m1UZw1JkquZYe3F1zQBN1xXsaf/view?usp=sharing

* b4-shazam-merge:
  RISC-V: cacheflush: Initialize CBO variables on ACPI systems
  RISC-V: ACPI: RHCT: Add function to get CBO block sizes
  RISC-V: ACPI: Update the return value of acpi_get_rhct()
  RISC-V: ACPI: Enhance acpi_os_ioremap with MMIO remapping

Link: https://lore.kernel.org/r/20231018124007.1306159-1-sunilvl@ventanamicro.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

The interrupt entries are expected to be in the .irqentry.text section.
For example, for kprobes to work properly, exception code cannot be
probed; this is ensured by blacklisting addresses in the .irqentry.text
section.

Fixes: 7db91e57 ("RISC-V: Task implementation")
Signed-off-by: Nam Cao <namcaov@gmail.com>
Link: https://lore.kernel.org/r/20230821145708.21270-1-namcaov@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Since the commit 011f09d1 set sv57 as default for CONFIG_64BIT,
the comment of CONFIG_PAGE_OFFSET should be updated too.

Fixes: 011f09d1 ("riscv: mm: Set sv57 on defaultly")
Signed-off-by: Song Shuai <suagrfillet@gmail.com>
Link: https://lore.kernel.org/r/20230809031023.3575407-1-songshuaishuai@tinylab.org
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Actually it is a part of Conor's
commit aae538cd ("riscv: fix detection of toolchain
Zihintpause support").
It is looks like a merge issue. Samuel's
commit 0b1d60d6 ("riscv: Fix build with
CONFIG_CC_OPTIMIZE_FOR_SIZE=y") do not base on Conor's commit and
revert to __riscv_zihintpause. So this patch can fix it.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Fixes: 3c349eac ("Merge patch "riscv: Fix build with CONFIG_CC_OPTIMIZE_FOR_SIZE=y"")
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230802064215.31111-1-minda.chen@starfivetech.com
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Swap type takes bits 7-11 and swap offset should start from bit 12.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20230921141652.2657054-1-xiao.w.wang@intel.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Extensions prefixed with "Su" won't corrupt the workaround in many
cases.  The only exception is when the first multi-letter extension in the
ISA string begins with "Su" and is not prefixed with an underscore.

For instance, following ISA string can confuse this QEMU workaround.

*   "rv64imacsuclic" (RV64I + M + A + C + "Suclic")

However, this case is very unlikely because extensions prefixed by either
"Z", "Sm" or "Ss" will most likely precede first.

For instance, the "Suclic" extension (draft as of now) will be placed after
related "Smclic" and "Ssclic" extensions.  It's also highly likely that
other unprivileged extensions like "Zba" will precede.

It's also possible to suppress the issue in the QEMU workaround with an
underscore.  Following ISA string won't confuse the QEMU workaround.

*   "rv64imac_suclic" (RV64I + M + A + C + delimited "Suclic")

This fix is to tell kernel developers the nature of this workaround
precisely.  There are some "Su*" extensions to be ratified but don't worry
about this workaround too much.

This commit comes with other minor editorial fixes (for minor wording and
spacing issues, without changing the meaning).
Signed-off-by: Tsukasa OI <research_trasio@irq.a4lg.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/8a127608cf6194a6d288289f2520bd1744b81437.1690350252.git.research_trasio@irq.a4lg.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

The pt_level uses CONFIG_PGTABLE_LEVELS to display page table names.
But if page mode is downgraded from kernel cmdline or restricted by
the hardware in 64BIT, it will give a wrong name.

Like, using no4lvl for sv39, ptdump named the 1G-mapping as "PUD"
that should be "PGD":

0xffffffd840000000-0xffffffd900000000    0x00000000c0000000         3G PUD     D A G . . W R V

So select "P4D/PUD" or "PGD" via pgtable_l5/4_enabled to correct it.

Fixes: e8a62cc2 ("riscv: Implement sv48 support")
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Signed-off-by: Song Shuai <suagrfillet@gmail.com>
Link: https://lore.kernel.org/r/20230712115740.943324-1-suagrfillet@gmail.com
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230830044129.11481-3-palmer@rivosinc.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

A few of the other page table level helpers are defined on rv32, but not
pgtable_l5_enabled.  This adds the definition as a constant and converts
pgtable_l4_enabled to a constant as well.

Link: https://lore.kernel.org/r/20230830044129.11481-2-palmer@rivosinc.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

When Sstc is available the RISC-V timer clock_event_device should be
the preferred clock_event_device hence we increase clock_event_device
rating for Sstc.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Link: https://lore.kernel.org/r/20230710131902.1459180-3-apatel@ventanamicro.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Currently, we enable/disable timer interrupt at runtime to start/stop
timer events. This makes timer interrupt state go out-of-sync with
the Linux interrupt subsystem.

To address the above issue, we can stop a per-HART timer interrupt
by setting U64_MAX in timecmp CSR (or sbi_set_timer()) at the time
of handling timer interrupt.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Link: https://lore.kernel.org/r/20230710131902.1459180-2-apatel@ventanamicro.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Andrew Jones <ajones@ventanamicro.com> says:

In order for usermode to issue cbo.zero, it needs privilege granted to
issue the extension instruction (patch 2) and to know that the extension
is available and its block size (patch 3). Patch 1 could be separate from
this series (it just fixes up some error messages), patches 4-5 convert
the hwprobe selftest to a statically-linked, TAP test and patch 6 adds a
new hwprobe test for the new information as well as testing CBO
instructions can or cannot be issued as appropriate.

* b4-shazam-merge:
  RISC-V: selftests: Add CBO tests
  RISC-V: selftests: Convert hwprobe test to kselftest API
  RISC-V: selftests: Statically link hwprobe test
  RISC-V: hwprobe: Expose Zicboz extension and its block size
  RISC-V: Enable cbo.zero in usermode
  RISC-V: Make zicbom/zicboz errors consistent

Link: https://lore.kernel.org/r/20230918131518.56803-8-ajones@ventanamicro.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Song Shuai <songshuaishuai@tinylab.org> says:

This series contains a cleanup for riscv_kexec_relocate() and two fixups
for KEXEC_FILE and had passed the basic kexec test in my 64bit Qemu-virt.

You can use this kexec-tools[3] to test the kexec-file-syscall and these patches.

riscv: kexec: Cleanup riscv_kexec_relocate (patch1)
==================================================

For readability and simplicity, cleanup the riscv_kexec_relocate code:

 - Re-sort the first 4 `mv` instructions against `riscv_kexec_method()`
 - Eliminate registers for debugging (s9,s10,s11) and storing const-value (s5,s6)
 - Replace `jalr` with `jr` for no-link jump

riscv: kexec: Align the kexeced kernel entry (patch2)
==================================================

The current riscv boot protocol requires 2MB alignment for RV64
and 4MB alignment for RV32.

In KEXEC_FILE path, the elf_find_pbase() function should align
the kexeced kernel entry according to the requirement, otherwise
the kexeced kernel would silently BUG at the setup_vm().

riscv: kexec: Remove -fPIE for PURGATORY_CFLAGS (patch3)
==================================================

With CONFIG_RELOCATABLE enabled, KBUILD_CFLAGS had a -fPIE option
and then the purgatory/string.o was built to reference _ctype symbol
via R_RISCV_GOT_HI20 relocations which can't be handled by purgatory.

As a consequence, the kernel failed kexec_load_file() with:

[  880.386562] kexec_image: The entry point of kernel at 0x80200000
[  880.388650] kexec_image: Unknown rela relocation: 20
[  880.389173] kexec_image: Error loading purgatory ret=-8

So remove the -fPIE option for PURGATORY_CFLAGS to generate
R_RISCV_PCREL_HI20 relocations type making puragtory work as it was.

 arch/riscv/kernel/elf_kexec.c      |  8 ++++-
 arch/riscv/kernel/kexec_relocate.S | 52 +++++++++++++-----------------
 arch/riscv/purgatory/Makefile      |  4 +++
 3 files changed, 34 insertions(+), 30 deletions(-)

* b4-shazam-merge:
  riscv: kexec: Remove -fPIE for PURGATORY_CFLAGS
  riscv: kexec: Align the kexeced kernel entry
  riscv: kexec: Cleanup riscv_kexec_relocate

Link: https://lore.kernel.org/r/20230907103304.590739-1-songshuaishuai@tinylab.orgSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

On RISC-V, the return address is before the current frame pointer,
unlike on most other architectures. Use the correct offset on RISC-V
to fix the CFI_BACKWARD test.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Acked-by: Kees Cook <keescook@chromium.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20230927224757.1154247-14-samitolvanen@google.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

When both CONFIG_IRQ_STACKS and SCS are enabled, also use a separate
per-CPU shadow call stack.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20230927224757.1154247-13-samitolvanen@google.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Implement CONFIG_SHADOW_CALL_STACK for RISC-V. When enabled, the
compiler injects instructions to all non-leaf C functions to
store the return address to the shadow stack and unconditionally
load it again before returning, which makes it harder to corrupt
the return address through a stack overflow, for example.

The active shadow call stack pointer is stored in the gp
register, which makes SCS incompatible with gp relaxation. Use
--no-relax-gp to ensure gp relaxation is disabled and disable
global pointer loading.  Add SCS pointers to struct thread_info,
implement SCS initialization, and task switching
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20230927224757.1154247-12-samitolvanen@google.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

In Clang 17, -fsanitize=shadow-call-stack uses the newly declared
platform register gp for storing shadow call stack pointers. As
this is obviously incompatible with gp relaxation, in preparation
for CONFIG_SHADOW_CALL_STACK support, move global pointer loading
to a single macro, which we can cleanly disable when SCS is used
instead.

Link: https://reviews.llvm.org/rGaa1d2693c256
Link: https://github.com/riscv-non-isa/riscv-elf-psabi-doc/commit/a484e843e6eeb51f0cb7b8819e50da6d2444d769Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20230927224757.1154247-11-samitolvanen@google.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

With CONFIG_IRQ_STACKS, we switch to a separate per-CPU IRQ stack
before calling handle_riscv_irq or __do_softirq. We currently
have duplicate inline assembly snippets for stack switching in
both code paths. Now that we can access per-CPU variables in
assembly, implement call_on_irq_stack in assembly, and use that
instead of redundant inline assembly.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Guo Ren <guoren@kernel.org>
Link: https://lore.kernel.org/r/20230927224757.1154247-10-samitolvanen@google.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

commit 31da94c2 ("riscv: add VMAP_STACK overflow detection") added
support for CONFIG_VMAP_STACK. If overflow is detected, CPU switches to
`shadow_stack` temporarily before switching finally to per-cpu
`overflow_stack`.

If two CPUs/harts are racing and end up in over flowing kernel stack, one
or both will end up corrupting each other state because `shadow_stack` is
not per-cpu. This patch optimizes per-cpu overflow stack switch by
directly picking per-cpu `overflow_stack` and gets rid of `shadow_stack`.

Following are the changes in this patch

 - Defines an asm macro to obtain per-cpu symbols in destination
   register.
 - In entry.S, when overflow is detected, per-cpu overflow stack is
   located using per-cpu asm macro. Computing per-cpu symbol requires
   a temporary register. x31 is saved away into CSR_SCRATCH
   (CSR_SCRATCH is anyways zero since we're in kernel).

Please see Links for additional relevant disccussion and alternative
solution.

Tested by `echo EXHAUST_STACK > /sys/kernel/debug/provoke-crash/DIRECT`
Kernel crash log below

 Insufficient stack space to handle exception!/debug/provoke-crash/DIRECT
 Task stack:     [0xff20000010a98000..0xff20000010a9c000]
 Overflow stack: [0xff600001f7d98370..0xff600001f7d99370]
 CPU: 1 PID: 205 Comm: bash Not tainted 6.1.0-rc2-00001-g328a1f96f7b9 #34
 Hardware name: riscv-virtio,qemu (DT)
 epc : __memset+0x60/0xfc
  ra : recursive_loop+0x48/0xc6 [lkdtm]
 epc : ffffffff808de0e4 ra : ffffffff0163a752 sp : ff20000010a97e80
  gp : ffffffff815c0330 tp : ff600000820ea280 t0 : ff20000010a97e88
  t1 : 000000000000002e t2 : 3233206874706564 s0 : ff20000010a982b0
  s1 : 0000000000000012 a0 : ff20000010a97e88 a1 : 0000000000000000
  a2 : 0000000000000400 a3 : ff20000010a98288 a4 : 0000000000000000
  a5 : 0000000000000000 a6 : fffffffffffe43f0 a7 : 00007fffffffffff
  s2 : ff20000010a97e88 s3 : ffffffff01644680 s4 : ff20000010a9be90
  s5 : ff600000842ba6c0 s6 : 00aaaaaac29e42b0 s7 : 00fffffff0aa3684
  s8 : 00aaaaaac2978040 s9 : 0000000000000065 s10: 00ffffff8a7cad10
  s11: 00ffffff8a76a4e0 t3 : ffffffff815dbaf4 t4 : ffffffff815dbaf4
  t5 : ffffffff815dbab8 t6 : ff20000010a9bb48
 status: 0000000200000120 badaddr: ff20000010a97e88 cause: 000000000000000f
 Kernel panic - not syncing: Kernel stack overflow
 CPU: 1 PID: 205 Comm: bash Not tainted 6.1.0-rc2-00001-g328a1f96f7b9 #34
 Hardware name: riscv-virtio,qemu (DT)
 Call Trace:
 [<ffffffff80006754>] dump_backtrace+0x30/0x38
 [<ffffffff808de798>] show_stack+0x40/0x4c
 [<ffffffff808ea2a8>] dump_stack_lvl+0x44/0x5c
 [<ffffffff808ea2d8>] dump_stack+0x18/0x20
 [<ffffffff808dec06>] panic+0x126/0x2fe
 [<ffffffff800065ea>] walk_stackframe+0x0/0xf0
 [<ffffffff0163a752>] recursive_loop+0x48/0xc6 [lkdtm]
 SMP: stopping secondary CPUs
 ---[ end Kernel panic - not syncing: Kernel stack overflow ]---

Cc: Guo Ren <guoren@kernel.org>
Cc: Jisheng Zhang <jszhang@kernel.org>
Link: https://lore.kernel.org/linux-riscv/Y347B0x4VUNOd6V7@xhacker/T/#t
Link: https://lore.kernel.org/lkml/20221124094845.1907443-1-debug@rivosinc.com/Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Co-developed-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Acked-by: Guo Ren <guoren@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20230927224757.1154247-9-samitolvanen@google.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Initialize the CBO variables on ACPI based systems using information in
RHCT.
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Samuel Holland <samuel.holland@sifive.com>
Link: https://lore.kernel.org/r/20231018124007.1306159-5-sunilvl@ventanamicro.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Cache Block Operation (CBO) related block size in ACPI is provided by RHCT.
Add support to read the CMO node in RHCT to get this information.
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20231018124007.1306159-4-sunilvl@ventanamicro.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

acpi_get_rhct() currently returns pointer to acpi_table_header
structure. But since this is specific to RHCT, return pointer to
acpi_table_rhct structure itself.
Suggested-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20231018124007.1306159-3-sunilvl@ventanamicro.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Enhance the acpi_os_ioremap() to support opregions in MMIO space. Also,
have strict checks using EFI memory map to allow remapping the RAM similar
to arm64.
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231018124007.1306159-2-sunilvl@ventanamicro.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>