Implement this callback in order to get the offloaded stats added to the
kernel stats.
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement this callback in order to get the offloaded stats added to the
kernel stats.
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Offload TC action pedit munge dsfield

Petr says:

The Spectrum switches allow packet prioritization based on DSCP on ingress,
and update of DSCP on egress. This is configured through the DCB APP rules.
For some use cases, assigning a custom DSCP value based on an ACL match is
a better tool. To that end, offload FLOW_ACTION_MANGLE to permit changing
of dsfield as a whole, or DSCP and ECN values in isolation.

After fixing a commentary nit in patch #1, and mlxsw naming in patch #2,
patches #3 and #4 add the offload to mlxsw.

Patch #5 adds a forwarding selftest for pedit dsfield, applicable to SW as
well as HW datapaths. Patch #6 adds a mlxsw-specific test to verify DSCP
rewrite due to DCB APP rules is not performed on pedited packets.

The tests only cover IPv4 dsfield setting. We have tests for IPv6 as well,
but would like to postpone their contribution until the corresponding
iproute patches have been accepted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When DSCP is updated through an offloaded pedit action, DSCP rewrite on
egress should be disabled. Add a test that check that it is so.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test that runs packets with dsfield set, and test that pedit adjusts
the DSCP or ECN parts or the whole field.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Offload action pedit ex munge when used with a flower classifier. Only
allow setting of DSCP, ECN, or the whole DSField in IPv4 and IPv6 packets.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The QOS_ACTION is used for manipulating the QOS attributes of the packet.
Add the defines and helpers related to DSCP and ECN fields, and dscp_rw.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original idea was to reuse this set of actions for ECN rewrite as well,
but on second look, it's not such a great idea. These two items should each
have its own command. Rename the existing enum to make it obvious that it
belongs to switch_prio_cmd.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This field references FLOW_ACTION_PACKET_EDIT. Such action does not exist
though. Instead the field is used for FLOW_ACTION_MANGLE and _ADD.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2020-03-25

1) Cleanups from Dan Carpenter and wenxu.

2) Paul and Roi, Some minor updates and fixes to E-Switch to address
issues introduced in the previous reg_c0 updates series.

3) Eli Cohen simplifies and improves flow steering matching group searches
and flow table entries version management.

4) Parav Pandit, improves devlink eswitch mode changes thread safety.
By making devlink rely on driver for thread safety and introducing mlx5
eswitch mode change protection.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/atheros/atlx/atl2.c:40:19: warning: ‘atl2_driver_string’ defined but not used [-Wunused-const-variable=]
 static const char atl2_driver_string[] = "Atheros(R) L2 Ethernet Driver";
                   ^~~~~~~~~~~~~~~~~~

commit ea973742 ("net/atheros: Clean atheros code from driver version")
left behind this, remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the commit f73b1281
("tipc: improve throughput between nodes in netns"), we're missing a check
to handle TIPC_DIRECT_MSG type, it's still using old sending mechanism for
this message type. So, throughput improvement is not significant as
expected.

Besides that, when sending a large message with that type, we're also
handle wrong receiving queue, it should be enqueued in socket receiving
instead of multicast messages.

Fix this by adding the missing case for TIPC_DIRECT_MSG.

Fixes: f73b1281 ("tipc: improve throughput between nodes in netns")
Reported-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently eswitch mode change is occurring from 2 different execution
contexts as below.
1. sriov sysfs enable/disable
2. devlink eswitch set commands

Both of them need to access eswitch related data structures in
synchronized manner.
Without any synchronization below race condition exist.

SR-IOV enable/disable with devlink eswitch mode change:

          cpu-0                         cpu-1
          -----                         -----
mlx5_device_disable_sriov()        mlx5_devlink_eswitch_mode_set()
  mlx5_eswitch_disable()             esw_offloads_stop()
    esw_offloads_disable()             mlx5_eswitch_disable()
                                         esw_offloads_disable()

Hence, they are synchronized using a new mode_lock.
eswitch's state_lock is not used as it can lead to a deadlock scenario
below and state_lock is only for vport and fdb exclusive access.

ip link set vf <param>
  netlink rcv_msg() - Lock A
    rtnl_lock
    vfinfo()
      esw->state_lock() - Lock B
devlink eswitch_set
   devlink_mutex
     esw->state_lock() - Lock B
       attach_netdev()
         register_netdev()
           rtnl_lock - Lock A

Alternatives considered:
1. Acquiring rtnl lock before taking esw->state_lock to follow similar
locking sequence as ip link flow during eswitch mode set.
rtnl lock is not good idea for two reasons.
(a) Holding rtnl lock for several hundred device commands is not good
    idea.
(b) It leads to below and more similar deadlocks.

devlink eswitch_set
   devlink_mutex
     rtnl_lock - Lock A
       esw->state_lock() - Lock B
         eswitch_disable()
           reload()
             ib_register_device()
               ib_cache_setup_one()
                 rtnl_lock()

2. Exporting devlink lock may lead to undesired use of it in vendor
driver(s) in future.

3. Unloading representors outside of the mode_lock requires
serialization with other process trying to enable the eswitch.

4. Differing the representors life cycle to a different workqueue
requires synchronization with func_change_handler workqueue.
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Subsequent patch protects eswitch mode changes across sriov and devlink
interfaces. It is desirable for eswitch to provide thread safe eswitch
enable and disable APIs.
Hence, extend eswitch enable API to optionally update num_vfs when
requested.

In subsequent patch, eswitch num_vfs are updated after all the eswitch
users eswitch drops its reference count.
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

In order to check eswitch state under a lock, prepare code to split
capability check and eswitch state check into two helper functions.
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

devlink_nl_cmd_eswitch_set_doit() doesn't hold devlink->lock mutex while
invoking driver callback. This is likely due to eswitch mode setting
involves adding/remove devlink ports, health reporters or
other devlink objects for a devlink device.

So it is driver responsiblity to ensure thread safe eswitch state
transition happening via either sriov legacy enablement or via devlink
eswitch set callback.

Therefore, get() callback should also be invoked without holding
devlink->lock mutex.
Vendor driver can use same internal lock which it uses during eswitch
mode set() callback.
This makes get() and set() implimentation symmetric in devlink core and
in vendor drivers.

Hence, remove holding devlink->lock mutex during eswitch get() callback.

Failing to do so results into below deadlock scenario when mlx5_core
driver is improved to handle eswitch mode set critical section invoked
by devlink and sriov sysfs interface in subsequent patch.

devlink_nl_cmd_eswitch_set_doit()
   mlx5_eswitch_mode_set()
     mutex_lock(esw->mode_lock) <- Lock A
     [...]
     register_devlink_port()
       mutex_lock(&devlink->lock); <- lock B

mutex_lock(&devlink->lock); <- lock B
devlink_nl_cmd_eswitch_get_doit()
   mlx5_eswitch_mode_get()
   mutex_lock(esw->mode_lock) <- Lock A

In subsequent patch, mlx5_core driver uses its internal lock during
get() and set() eswitch callbacks.

Other drivers have been inspected which returns either constant during
get operations or reads the value from already allocated structure.
Hence it is safe to remove the lock in get( ) callback and let vendor
driver handle it.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

mlx5_unload_one() always returns 0.
Simplify callers of mlx5_unload_one() and remove the dead code.
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

mlx5_register_device() doesn't check for any error and always returns 0.
Simplify mlx5_register_device() to return void and its caller, remove
dead code related to it.
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Group version is used when modifying a rule is allowed
(FLOW_ACT_NO_APPEND is clear) to detect a case where the rule was found
but while the groups where unlocked a new FTE was added. In this case,
the added FTE could be one with identical match value so we need to
attempt again with group lock held.

Change the code so version is retrieved only when FLOW_ACT_NO_APPEND is
cleared. As result, later compare can also be avoided if FLOW_ACT_NO_APPEND
is cleared.

Also improve comments text.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

FTE version is not used anywhere in the code so avoid incrementing it.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When adding a rule to a flow group we need increment the version of the
group. Current code fails to do that and as a result, when trying to add
a rule, we will fail to discover a case where an FTE with the same match
value was added while we scanned the groups of the same match criteria,
thus we may try to add an FTE that was already added.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Instead of using two different structs for searching groups with the
same match, use a single struct and thus simplify the code, make it more
readable and smaller size which means less code cache misses.

         text    data     bss     dec     hex
before: 35524    2744       0   38268    957c
after:  35038    2744       0   37782    9396

When testing add 70000 rules, delete all the rules, and repeat three
times taking the average, we get (time in seconds):

Before the change: insert 16.80, delete 11.02
After the change:  insert 16.55, delete 10.95
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The correct type is u32.

Fixes: d18296ff ("net/mlx5: E-Switch, Introduce global tables")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

We allocate a temporary memory but forget to free it.

Fixes: 11b717d6 ("net/mlx5: E-Switch, Get reg_c0 value on CQE")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Register c0 loopback is needed to fully support chains and prios.

Enable chains and prio only if loopback (of reg c1 which came together
with c0), is enabled. To be able to check that, move enabling of loopback
before eswitch chains init.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Reg c0/c1 matching, rewrite of regs c0/c1, and copy header of regs c1,B
is needed for the restore table to function, might not be supported by
firmware, and creation of the restore table or the copy header will
fail.

Check reg_c1 loopback support, as firmware which supports this,
should have all of the above.

Fixes: 11b717d6 ("net/mlx5: E-Switch, Get reg_c0 value on CQE")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The function mlx5e_rep_setup_ft_cb check chain_index is zero twice.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The actions_match_supported() function returns a bool, true for success
and false for failure.  This error path is returning a negative which
is cast to true but it should return false.

Fixes: 4c3844d9 ("net/mlx5e: CT: Introduce connection tracking")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Overlapping header include additions in macsec.c

A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c

Overlapping test additions in selftests Makefile

Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Fix deadlock in bpf_send_signal() from Yonghong Song.

 2) Fix off by one in kTLS offload of mlx5, from Tariq Toukan.

 3) Add missing locking in iwlwifi mvm code, from Avraham Stern.

 4) Fix MSG_WAITALL handling in rxrpc, from David Howells.

 5) Need to hold RTNL mutex in tcindex_partial_destroy_work(), from Cong
    Wang.

 6) Fix producer race condition in AF_PACKET, from Willem de Bruijn.

 7) cls_route removes the wrong filter during change operations, from
    Cong Wang.

 8) Reject unrecognized request flags in ethtool netlink code, from
    Michal Kubecek.

 9) Need to keep MAC in reset until PHY is up in bcmgenet driver, from
    Doug Berger.

10) Don't leak ct zone template in act_ct during replace, from Paul
    Blakey.

11) Fix flushing of offloaded netfilter flowtable flows, also from Paul
    Blakey.

12) Fix throughput drop during tx backpressure in cxgb4, from Rahul
    Lakkireddy.

13) Don't let a non-NULL skb->dev leave the TCP stack, from Eric
    Dumazet.

14) TCP_QUEUE_SEQ socket option has to update tp->copied_seq as well,
    also from Eric Dumazet.

15) Restrict macsec to ethernet devices, from Willem de Bruijn.

16) Fix reference leak in some ethtool *_SET handlers, from Michal
    Kubecek.

17) Fix accidental disabling of MSI for some r8169 chips, from Heiner
    Kallweit.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (138 commits)
  net: Fix CONFIG_NET_CLS_ACT=n and CONFIG_NFT_FWD_NETDEV={y, m} build
  net: ena: Add PCI shutdown handler to allow safe kexec
  selftests/net/forwarding: define libs as TEST_PROGS_EXTENDED
  selftests/net: add missing tests to Makefile
  r8169: re-enable MSI on RTL8168c
  net: phy: mdio-bcm-unimac: Fix clock handling
  cxgb4/ptp: pass the sign of offset delta in FW CMD
  net: dsa: tag_8021q: replace dsa_8021q_remove_header with __skb_vlan_pop
  net: cbs: Fix software cbs to consider packet sending time
  net/mlx5e: Do not recover from a non-fatal syndrome
  net/mlx5e: Fix ICOSQ recovery flow with Striding RQ
  net/mlx5e: Fix missing reset of SW metadata in Striding RQ reset
  net/mlx5e: Enhance ICOSQ WQE info fields
  net/mlx5_core: Set IB capability mask1 to fix ib_srpt connection failure
  selftests: netfilter: add nfqueue test case
  netfilter: nft_fwd_netdev: allow to redirect to ifb via ingress
  netfilter: nft_fwd_netdev: validate family and chain type
  netfilter: nft_set_rbtree: Detect partial overlaps on insertion
  netfilter: nft_set_rbtree: Introduce and use nft_rbtree_interval_start()
  netfilter: nft_set_pipapo: Separate partial and complete overlap cases on insertion
  ...

Pull GPIO fixes from Linus Walleij:

 - One core quirk by myself to fix the .irq_disable() semantics when the
   gpiolib core takes over this callback.

 - The rest is an elaborate series of four patches fixing Intel laptop
   ACPI wakeup quirks.

* tag 'gpio-v5.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpiolib: acpi: Add quirk to ignore EC wakeups on HP x2 10 CHT + AXP288 model
  gpiolib: acpi: Add quirk to ignore EC wakeups on HP x2 10 BYT + AXP288 model
  gpiolib: acpi: Rework honor_wakeup option into an ignore_wake option
  gpiolib: acpi: Correct comment for HP x2 10 honor_wakeup quirk
  gpiolib: Fix irq_disable() semantics

Merge tag 'wireless-drivers-2020-03-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for v5.6

Fourth, and last, set of fixes for v5.6. Just two important fixes to
iwlwifi regressions.

iwlwifi

* fix GEO_TX_POWER_LIMIT command on certain devices which caused
  firmware to crash during initialisation

* add back device ids for three devices which were accidentally
  removed
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

net/netfilter/nft_fwd_netdev.c: In function ‘nft_fwd_netdev_eval’:
    net/netfilter/nft_fwd_netdev.c:32:10: error: ‘struct sk_buff’ has no member named ‘tc_redirected’
      pkt->skb->tc_redirected = 1;
              ^~
    net/netfilter/nft_fwd_netdev.c:33:10: error: ‘struct sk_buff’ has no member named ‘tc_from_ingress’
      pkt->skb->tc_from_ingress = 1;
              ^~

To avoid a direct dependency with tc actions from netfilter, wrap the
redirect bits around CONFIG_NET_REDIRECT and move helpers to
include/linux/skbuff.h. Turn on this toggle from the ifb driver, the
only existing client of these bits in the tree.

This patch adds skb_set_redirected() that sets on the redirected bit
on the skbuff, it specifies if the packet was redirect from ingress
and resets the timestamp (timestamp reset was originally missing in the
netfilter bugfix).

Fixes: bcfabee1 ("netfilter: nft_fwd_netdev: allow to redirect to ifb via ingress")
Reported-by: noreply@ellerman.id.au
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit adds support to catch any bits set in SGE_INT_CAUSE5 for Parity Errors.
F_ERR_T_RXCRC flag is used to ignore that particular bit as it is not considered as fatal.
So, we clear out the bit before looking for error.
This patch now read and report separately all three registers(Cause1, Cause2, Cause5).
Also, checks for errors if any.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Rahul Kundu <rahul.kundu@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sunil Goutham says:

====================
octeontx2-pf: Miscellaneous fixes

This patchset fixes couple of issues related to missing
page refcount updation and taking a mutex lock in atomic
context.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since set_rx_mode takes a mutex lock for sending mailbox
message to admin function to set the mode, moved logic
to a workqueue.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixed an issue wherein while refilling receive buffers
for the last page allocated, recount is not being updated.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/qeth: updates 2020-03-25

please apply the following patch series for qeth to netdev's net-next
tree.
Same series as yesterday, with one minor update to patch 1 as per
your review.

This adds
1) NAPI poll support for the async-Completion Queue (with one qdio layer
   patch acked by Heiko),
2) ethtool support for per-queue TX IRQ coalescing,
3) various cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace list_for_each() with list_for_each_entry(), and
list_entry(head.next) with list_first_entry().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a device is configured in prio-queue mode to pin all traffic onto
a specific HW queue, treat this as a distinct variant of prio-queueing
instead of QETH_NO_PRIO_QUEUEING.

This corrects an error message from qeth_osa_set_output_queues() for
devices configured in such a mode.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>