- 30 Jan, 2023 1 commit
-
-
Luca Ellero authored
ADS7845 doesn't support pressure. Avoid the following error reported by libinput-list-devices: "ADS7845 Touchscreen: kernel bug: device has min == max on ABS_PRESSURE". Fixes: ffa458c1 ("spi: ads7846 driver") Signed-off-by:
Luca Ellero <l.ellero@asem.it> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20230126105227.47648-2-l.ellero@asem.itSigned-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
- 27 Jan, 2023 18 commits
-
-
John Butler authored
Add VID and PID to the xpad_device table to allow driver to use the 8BitDo Pro 2 Wired Controller, which is XTYPE_XBOX360 compatible by default. Signed-off-by:
John Butler <radon86dev@gmail.com> Reviewed-by:
Mattijs Korpershoek <mkorpershoek@baylibre.com> Link: https://lore.kernel.org/r/20230124005206.80706-1-radon86dev@gmail.comSigned-off-by:
-
Arnd Bergmann authored
The previous change was not properly build tested and needs a trivial spelling change: ipaq-micro-ts.c:146:8: error: type defaults to 'int' in declaration of 'DEFINE_SIMPLE_DEV_PM' [-Werror=implicit-int] Fixes: 144ff5e0 ("Input: ipaq-micro-ts - use DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Reviewed-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Link: https://lore.kernel.org/r/20230117164539.1631336-1-arnd@kernel.orgSigned-off-by:
-
Jonathan Cameron authored
As the guards only apply to suspend and resume, #ifdef CONFIG_PM_SLEEP would have been a tighter protection. As pm_sleep_ptr() lets the compiler see the protected ops structure and callbacks but also lets the compiler remove it as unused code if !CONFIG_PM_SLEEP this allows the #ifdef guards to be removed, slightly simplifying the resulting code. -- It seems likely that DEFINE_SIMPLE_DEV_PM_OPS() would work here but I'd prefer not to make that change unless someone can confirm that the extra callbacks registered will have no unwanted side effects in this driver. Signed-off-by:
-
Jonathan Cameron authored
As the guards only apply to suspend and resume, #ifdef CONFIG_PM_SLEEP would have been a tighter protection. As pm_sleep_ptr() lets the compiler see the protected ops structure and callbacks but also lets the compiler remove it as unused code if !CONFIG_PM_SLEEP this allows the #ifdef guards to be removed, slightly simplifying the resulting code. Signed-off-by:
-
Jonathan Cameron authored
As the new pm_sleep_ptr() macro lets the compiler see the code, but then remove it if !CONFIG_PM_SLEEP it can be used to avoid the need for #ifdef guards. Use that in the input core to simplify the code a little. Note pm_sleep_ptr() has not been applied to each callback in the ops structure because the pm_sleep_ptr() at the usage site is sufficient. Signed-off-by:
-
Jonathan Cameron authored
SET_RUNTIME_DEV_PM_OPS() is deprecated as it requires explicit protection against unused function warnings. The new combination of pm_ptr() and RUNTIME_DEV_PM_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the __maybe_unused markings. Note that DEFINE_RUNTIME_DEV_PM_OPS() is not used because that adds additional callbacks for suspend and resume and would need testing. Signed-off-by:
-
Jonathan Cameron authored
SET_SYSTEM_SLEEP_PM_OPS() is deprecated as it requires explicit protection against unused function warnings. The new combination of pm_sleep_ptr() and SYSTEM_SLEEP_PM_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the __maybe_unused markings. In this case we also have a .poweroff_late() callback. Whilst not strictly necessary, to future proof against relaxation of the protection of the main driver.pm = pm_sleep_ptr() protect this pointer with pm_sleep_ptr() as would be done if the LATE_SYSTEM_SLEEP_PM_OPS() macro were used to set it. Signed-off-by:
-
Jonathan Cameron authored
SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection against unused function warnings. The new combination of pm_sleep_ptr() and EXPORT_GPL_SIMPLE_DEV_PMU_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the __maybe_unused markings. It also rolls in the EXPORT_SYMBOL() so that we only export it if CONFIG_PM_SLEEP. Signed-off-by:
-
Jonathan Cameron authored
SET_SYSTEM_SLEEP_PM_OPS() and RUNTIME_PM_OPS() are deprecated as they requires explicit protection against unused function warnings. The new combination of pm_ptr() EXPORT_GPL_RUNTIME_DEV_PM_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the #ifdef guards. Note that we are replacing an unconditional call to the suspend and resume functions for sleep use cases with one via pm_runtime_force_suspend() / pm_runtime_force_resume() that only do anything to the device if we are not already in the appropriate runtime suspended state. Signed-off-by:
-
Jonathan Cameron authored
SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection against unused function warnings. The new combination of pm_sleep_ptr() and EXPORT_GPL_SIMPLE_DEV_PM_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the __maybe_unused markings. This function also removes the need for separate EXPORT_SYMBOL_GPL() Signed-off-by:
-
Jonathan Cameron authored
The I2C and SPI PM callbacks were identical (though wrapped in some bouncing out to the bus specific container of the struct device and then back again to get the drvdata). As such rather than just moving these to SIMPLE_DEV_PM_OPS() and pm_sleep_ptr() take the opportunity to unify the struct dev_pm_ops and use the new EXPORT_SIMPLE_DEV_PM_OPS() macro so that we can drop the unused suspend and resume callbacks as well as the structure if !CONFIG_PM_SLEEP without needing to mark the callbacks __maybe_unused. Signed-off-by:
-
Jonathan Cameron authored
The I2C and SPI PM callbacks were identical (though wrapped in some bouncing out to the bus specific container of the struct device and then back again to get the drvdata). As such rather than just moving these to SIMPLE_DEV_PM_OPS() and pm_sleep_ptr() take the opportunity to unify the struct dev_pm_ops and use the new EXPORT_SIMPLE_DEV_PM_OPS() macro so that we can drop the unused suspend and resume callbacks as well as the structure if !CONFIG_PM_SLEEP without needing to mark the callbacks __maybe_unused. Signed-off-by:
-
Jonathan Cameron authored
SET_SYSTEM_SLEEP_PM_OPS() and SET_RUNTIME_PM_OPS() are deprecated as they require explicit protection against unused function warnings. The new combination of pm_ptr() and SYSTEM_SLEEP_PM_OPS()/ RUNTIME_PM_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the __maybe_unused markings. Signed-off-by:
-
Jonathan Cameron authored
SET_SYSTEM_SLEEP_PM_OPS() and SET_RUNTIME_PM_OPS() are deprecated as they requires explicit protection against unused function warnings. The new combination of pm_ptr() and SYSTEM_SLEEP_PM_OPS() / RUNTIME_PM_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the #ifdef guards. Whilst all 3 sets of callbacks are similar, there are small differences that make it challenging to use a single pm_dev_ops structure - hence leave the duplication as it stands. Signed-off-by:
-
Jonathan Cameron authored
SET_SYSTEM_SLEEP_PM_OPS() and SET_RUNTIME_PM_OPS() are deprecated as they require explicit protection against unused function warnings. The new combination of pm_ptr() and SYSTEM_SLEEP_PM_OPS()/ RUNTIME_PM_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the __maybe_unused markings. Signed-off-by:
-
Jonathan Cameron authored
The SET_ variants are deprecated as they require explicit protection against unused function warnings. The new combination of pm_ptr() and SYSTEM_SLEEP/RUNTIME_DEV_PM_OPS() allow the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the #ifdef guards. Signed-off-by:
-
Jonathan Cameron authored
SET_SYSTEM_SLEEP_PM_OPS() is deprecated as it requires explicit protection against unused function warnings. The new combination of pm_sleep_ptr() and SYSTEM_SLEEP_PM_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the __maybe_unused markings. Here the additional .resume_noirq callback is protected with pm_sleep_ptr(). This isn't strictly necessary but is done for consistency with the other callbacks. Signed-off-by:
-
Jonathan Cameron authored
SET_SYSTEM_SLEEP_PM_OPS() and SET_RUNTIME_PM_OPS() are deprecated as they require explicit protection against unused function warnings. The new combination of pm_ptr() and SYSTEM_SLEEP_PM_OPS()/ RUNTIME_PM_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the __maybe_unused markings. Signed-off-by:
-
- 20 Jan, 2023 1 commit
-
-
joewu (吳仲振) authored
Add 3 extra buttons: 'brightness up', 'brightness down' and 'screen lock' to support monitor manipulating function. Signed-off-by:
Joe Wu <joewu@msi.com> Link: https://lore.kernel.org/r/e23628e2cb464d238eb1c33a9e1e516b@msi.comSigned-off-by:
-
- 11 Jan, 2023 5 commits
-
-
Jeff LaBundy authored
After initial start-up, the driver triggers ATI (calibration) with the newly loaded register configuration in place. Next, the driver polls a register field to ensure ATI completed in a timely fashion and that the device is ready to sense. However, communicating with the device over I2C while ATI is under- way may induce noise in the device and cause ATI to fail. As such, the vendor recommends not to poll the device during ATI. To solve this problem, let the device naturally signal to the host that ATI is complete by way of an interrupt. A completion prevents the device from successfully probing until this happens. As an added benefit, initial switch states are now reported in the interrupt handler at the same time ATI status is checked. As such, duplicate code that reports initial switch states has been removed from iqs269_input_init(). The former logic that scaled ATI timeout and filter settling delay is not carried forward with the new implementation, as it produces overly conservative delays at the lower clock rate. Rather, a single timeout that covers both clock rates is used. The filter settling delay does not happen to be necessary and has been removed as well. Fixes: 04e49867 ("Input: add support for Azoteq IQS269A") Signed-off-by:
Jeff LaBundy <jeff@labundy.com> Reviewed-by:
-
Jeff LaBundy authored
Polling the device while it transitions from automatic to manual power mode switching may keep the device from actually finishing the transition. The process appears to time out depending on the polling rate and the device's core clock frequency. This is ultimately unnecessary in the first place; instead it is sufficient to write the desired mode during initialization, then disable automatic switching at suspend. This eliminates the need to ensure the device is prepared for a manual change and removes the 'suspend_mode' variable. Similarly, polling the device while it transitions from one mode to another under manual control may time out as well. This added step does not appear to be necessary either, so drop it. Fixes: 04e49867 ("Input: add support for Azoteq IQS269A") Signed-off-by:
-
Jeff LaBundy authored
Unless it is being done as part of servicing a soft reset interrupt, configuring channels on-the-fly (as is the case when writing to the ati_trigger attribute) may cause GPIO3 (which reflects the state of touch for a selected channel) to be inadvertently asserted. To solve this problem, follow the vendor's recommendation and write all channel configuration as well as the REDO_ATI register field as part of a single block write. This ensures the device has been told to re-calibrate itself following an I2C stop condition, after which sensing resumes and GPIO3 may be asserted. Fixes: 04e49867 ("Input: add support for Azoteq IQS269A") Signed-off-by:
-
Jeff LaBundy authored
The time the device takes to deassert its RDY output following an I2C stop condition scales with the core clock frequency. To prevent level-triggered interrupts from being reasserted after the interrupt handler returns, increase the time before returning to account for the worst-case delay (~140 us) plus margin. Fixes: 04e49867 ("Input: add support for Azoteq IQS269A") Signed-off-by:
-
Jeff LaBundy authored
Each call to device/fwnode_get_named_child_node() must be matched with a call to fwnode_handle_put() once the corresponding node is no longer in use. This ensures a reference count remains balanced in the case of dynamic device tree support. Currently, the driver does not call fwnode_handle_put() on nested event nodes. This patch solves this problem by adding the missing instances of fwnode_handle_put(). As part of this change, the logic which parses each channel's key code is gently refactored in order to reduce the number of places from which fwnode_handle_put() is called. Fixes: 04e49867 ("Input: add support for Azoteq IQS269A") Signed-off-by:
-
- 10 Jan, 2023 15 commits
-
-
Dmitry Torokhov authored
Merge with mainline to bring in timer_shutdown_sync() API.
-
Jonathan Cameron authored
This driver never used the older SIMPLE_DEV_PM_OPS() but instead just set two of the callbacks directly. Skip that deprecated macro and go straight to the new form that avoids the need for guarding or marking callbacks __maybe_unused. -- It is possible there is some subtle reason why only two of the callbacks normally set by SIMPLE_DEV_PM_OPS() are set. As such, this one needs some closer reading than many of the others. Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20230102181842.718010-70-jic23@kernel.orgSigned-off-by:
-
Jonathan Cameron authored
SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection against unused function warnings. The new combination of pm_sleep_ptr() and DEFINE_SIMPLE_DEV_PM_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the __maybe_unused markings. Signed-off-by:
-
Jonathan Cameron authored
SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection against unused function warnings. The new combination of pm_sleep_ptr() and DEFINE_SIMPLE_DEV_PM_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the __maybe_unused markings. Signed-off-by:
-
Jonathan Cameron authored
SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection against unused function warnings. The new combination of pm_sleep_ptr() and DEFINE_SIMPLE_DEV_PM_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the __maybe_unused markings. Signed-off-by:
-
Jonathan Cameron authored
SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection against unused function warnings. The new combination of pm_sleep_ptr() and DEFINE_SIMPLE_DEV_PM_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the __maybe_unused markings. Signed-off-by:
-
Jonathan Cameron authored
SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection against unused function warnings. The new combination of pm_sleep_ptr() and DEFINE_SIMPLE_DEV_PM_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the __maybe_unused markings. Signed-off-by:
Alistair Francis <alistair@alistair23.me> Reviewed-by:
-
Jonathan Cameron authored
SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection against unused function warnings. The new combination of pm_sleep_ptr() and DEFINE_SIMPLE_DEV_PM_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the __maybe_unused markings. Signed-off-by:
-
Jonathan Cameron authored
SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection against unused function warnings. The new combination of pm_sleep_ptr() and DEFINE_SIMPLE_DEV_PM_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the __maybe_unused markings. Signed-off-by:
-
Jonathan Cameron authored
SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection against unused function warnings. The new combination of pm_sleep_ptr() and DEFINE_SIMPLE_DEV_PM_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the __maybe_unused markings. Signed-off-by:
-
Jonathan Cameron authored
SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection against unused function warnings. The new combination of pm_sleep_ptr() and DEFINE_SIMPLE_DEV_PM_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the __maybe_unused markings. Signed-off-by:
-
Jonathan Cameron authored
SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection against unused function warnings. The new combination of pm_sleep_ptr() and DEFINE_SIMPLE_DEV_PM_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the __maybe_unused markings. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Reviewed-by:
-
Jonathan Cameron authored
SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection against unused function warnings. The new combination of pm_sleep_ptr() and DEFINE_SIMPLE_DEV_PM_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the __maybe_unused markings. Signed-off-by:
-
Jonathan Cameron authored
SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection against unused function warnings. The new combination of pm_sleep_ptr() and DEFINE_SIMPLE_DEV_PM_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the __maybe_unused markings. Signed-off-by:
-
Jonathan Cameron authored
SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection against unused function warnings. The new combination of pm_sleep_ptr() and DEFINE_SIMPLE_DEV_PM_OPS() allows the compiler to see the functions, thus suppressing the warning, but still allowing the unused code to be removed. Thus also drop the __maybe_unused markings. Signed-off-by:
-
