KBUILD_MODNAME normalizes "-" to "_".  This is non-obvious and results in
the id name for ADP5588 being "adp5588_keys" while the other supported id
is "adp5587-keys".  So avoid this define and use an explicit string as the
id name.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Instead of using asynchronous SPI API and then spinning waiting for SPI
transfer to complete when disabling the device, let's use threaded IRQ
model and spi_sync().
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Tested-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Instead of manually creating one set of attributes or another set up
is_visible method in attribute group structure to control whether
aux3 or gpio3 attribute is presented to userspace.
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

PS2Mult is a simple serial protocol used for multiplexing several PS/2
streams into one serial data stream. It's used e.g. on TQM85xx series
of boards.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

We need to always call usb_autopm_put_interface() in wacom_open(),
not only when initialization fails, otherwise the device will be
marked as PM-busy and will never be put in suspended state.

Based on patch by Oliver Neukum.
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Suppress events where pressure > pressure_max.
These events come typically along with inaccurate X and Y samples.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Some input users such as Android or X require BTN_TOUCH events.
Implement EV_KEY:BTN_TOUCH and make sure that the release event
is not erroneous scheduled without a preceding valid touch.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

According to the AD7877 datasheet:

Each transfer operation is 16-bit. If multiple read/write operations are
to be performed, CS must be taken high after the end of each read/write
operation before another read/write operation can be performed by
taking CS low again.

Make sure CS toggles after each transfer in the message.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Make hp680_ts_init/exit() call cancel_delayed_work_sync() instead of
calling cancel_delayed_work() followed by flush_scheduled_work().

This is to prepare for the deprecation and removal of
flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

When annotating mutex to avoid false lockdep reports we should not
be using MOUSEDEV_MIX as lock subclass but rather SINGLE_DEPTH_NESTING.
Signed-off-by: Hitoshi Mitake <mitake@dcl.info.waseda.ac.jp>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Commit 91143379 introduces regulator operations in ads7846 touchscreen
driver. Among these operations, some are called while holding a
spinlock. On many platforms regulators reside on slow buses, such as
I2C/SPI and require sleep while accessing them.

The touchscreen itself is also a SPI device and currently relies on
asynchronous SPI access to avoid sleeping in interrupt context. Let's
switch to using threaded IRQ to be able to access SPI bus
synchronously (which simplifies driver a bit); it also allows safe
access to the regulators as well.

This has been tested on the ti_omap3530evm board:
 1) using ts_lib after normal boot
 2) using ts_lib after "#echo 1/0 > /sys/bus/spi/devices/spi0.1/disable"
 3) using ts_lib after "#echo mem > /sys/power/state" and "wake up"

Also tested on pandora.

Based on original patch by Dmitry Torokhov.
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Some (rare) serio devices need to have multiple serio children. One of
the examples is PS/2 multiplexer present on several TQC STKxxx boards,
which connect PS/2 keyboard and mouse to single tty port.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

There was too much knowledge about internals if serio in the pass-through
handling, clean it up.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Add the ROHM BU21013 capacitive touch panel controller support with
i2c interface.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Naveen Kumar Gaddipati <naveen.gaddipati@stericsson.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Program keyboard controller to generate a wake-up request on events and
on long key presses. It will not generate wake-up requests on timeouts
since driver code does not handle them.

This allows keyboard to wake-up OMAP from suspend.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Select correct interrupt line behaviour.
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Remove SYSCONFIG register configuration, omap hwmod framework will
use internal API to modify as required.

Other minor updates:

- Change a variable name from DEF to VAL, this represents a value
- Break line width to 80 characters
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Get mem and irq resources using platform helpers

 - platform_get_base
 - platform_get_irq
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Add support for the keypad controller in the Scroll Key Encoder (SKE)
module on the Nomadik family and the DB8500 SoC.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

We should not try to call free_irq() when request_irq() failed.
Reported-by: G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Instead of using -1 let's start using proper error codes.
Signed-off-by: Davidlohr Bueso <dave@gnu.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Rework emu_probe() to make sure we leave the device disabled if probe
fails for any reason.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Signed-off-by: Dzianis Kahanovich <mahatma@eu.by>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Currently the pressure range in Cintiq 21UX2 is limited to half of the
supported. This patch fixes the problem.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
CC: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

When runtime PM is enabled by default for input devices, X hangs in
wacom open:
[<ffffffff814a00ea>] mutex_lock+0x1a/0x40
[<ffffffffa02bc94b>] wacom_resume+0x3b/0x90 [wacom]
[<ffffffff81327a32>] usb_resume_interface+0xd2/0x190
[<ffffffff81327b5d>] usb_resume_both+0x6d/0x110
[<ffffffff81327c24>] usb_runtime_resume+0x24/0x40
[<ffffffff8130a2cf>] __pm_runtime_resume+0x26f/0x450
[<ffffffff8130a23a>] __pm_runtime_resume+0x1da/0x450
[<ffffffff8130a53a>] pm_runtime_resume+0x2a/0x50
[<ffffffff81328176>] usb_autopm_get_interface+0x26/0x60
[<ffffffffa02bc626>] wacom_open+0x36/0x90 [wacom]

wacom_open() takes wacom->lock and calls usb_autopm_get_interface(),
which in turn calls wacom_resume() which tries to acquire the lock
again.

The fix is to call usb_autopm_get_interface() first, before we take
the lock.

Since we do not do usb_autopm_put_interface() until wacom_close()
is called runtime PM is effectively disabled for the driver, however
changing it now would risk regressions so the complete fix will
have to wait till the next merge window.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Similarly to the keyboard handler, we are called by different input
devices and thus need to add spinlock if we want to maintain our
state properly.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Keep the file consistent and make clear that we mean 144 instead of -112.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

pci_disable_device() is called for following 2 cases
- error path in emu_probe()
- in emu_remove()
Signed-off-by: Rahul Ruikar <rahul.ruikar@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

This adds support for hanwang Art Master HD 5012 electromagnetic tablet.
Signed-off-by: Xing Wei <weixing@hanwang.com.cn>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Fixed JSIOCSAXMAP ioctl to update absmap, the map from hardware axis to
event axis in addition to abspam.  This fixes a regression introduced
by 999b874f.
Signed-off-by: Kenneth Waters <kwwaters@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

The input devices created by uinput do not currently handle multitouch
properly. All events will appear as if they came from slot zero, and
the input event buffers are not adjusted. This patch creates the MT
slots during setup, and sets the number of events per packet based
on the MT usage.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Currently HID layer only allows to remap keycodes for known usages,
and responds with -EINVAL when user tries to map new usage code.
This precludes us form relying on udev/keymap for establishing correct
mappings and forces us to write dummy HID drivers responsible only for
setting up keymaps.

Let's allow remapping not only usages that have been set up as keys
(usage->type == EV_KEY) but also yet-unmapped usages (usage->type == 0).
Acked-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Switch the code to use new style of getkeycode and setkeycode
methods to allow retrieving and setting keycodes not only by
their scancodes but also by index.
Acked-by: Ville Syrjälä <syrjala@sci.fi>
Tested-by: Jarod Wilson <jarod@wilsonet.com>
Tested-by: Ville Syrjälä <syrjala@sci.fi>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Nobody uses it anymore.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Memory pointed to by the pointer should not change.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Nobody uses it anymore.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Memory pointed to by these fields is not supposed to change.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>