- 12 Jul, 2005 40 commits
-
-
Andrew Morton authored
kernel/power/disk.c needs a declaration of name_to_dev_t() in scope. mount.h seems like an appropriate choice. Signed-off-by:
Andrew Morton <akpm@osdl.org> Signed-off-by:
Linus Torvalds <torvalds@osdl.org>
-
Linus Torvalds authored
-
Linus Torvalds authored
-
Linus Torvalds authored
-
Tommy Christensen authored
OK, I can see what's happening here. eth0 doesn't detect link-up until after a few seconds, so when the vlan interface is opened immediately after eth0 has been opened, it inherits the link-down state. Subsequently the vlan interface is never properly activated and are thus unable to transmit any packets. dev->state bits are not supposed to be manipulated directly. Something similar is probably needed for the netif_device_present() bit, although I don't know how this is meant to work for a virtual device. Signed-off-by:David S. Miller <davem@davemloft.net>
-
Andrew Morton authored
arch/sparc64/kernel/smp.c:48: error: parse error before "__attribute__" arch/sparc64/kernel/smp.c:49: error: parse error before "__attribute__" Signed-off-by:
-
Alexey Dobriyan authored
tr_type_trans(), hippi_type_trans() left as-is. Signed-off-by:
Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by:
-
Phil Oester authored
Revert the nf_reset change that caused so much trouble, drop conntrack references manually before packets are queued to packet sockets. Signed-off-by:
Phil Oester <kernel@linuxace.com> Signed-off-by:
Patrick McHardy <kaber@trash.net> Signed-off-by:
-
Michael Hund authored
The following driver provides complete interrupt-in and interrupt-out reports (raw data) to a user program. Until now it uses the HIDIOCGDEVINFO ioctl call, because I don't know better :-(. Perhaps, it will be ok for you - and I will be happy, if you assign 8 minor numbers. I have tested it in several environments and it works very well for me. However, it has a problem with two or more devices at the same hub, if the two or more devices need 1 ms interrupt-in transfers. Unfortunately more than one interrupt-in transfer every ms isn't possible (ehci driver?). This is why the min_interrupt_in_interval and min_interrupt_out_interval are increased to 2 ms (see the corresponding module parameters). This way, I can use two devices simultaneously at the same hub. Signed-off-by:
Michael Hund <mhund@ld-didactic.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
brian@murphy.dk authored
This increases the reference count on the usb cdc acm control interface which is referred to by the tty interface provided by the driver. This allows the deferred removal of the tty after the physical device is disconnected if the tty is held open at the time of disconnection. Signed-off-by: brian@murphy.dk Signed-off-by: -
brian@murphy.dk authored
Export usb_get_intf and usb_put_intf so that modules can increase usb interface reference counts. Signed-off-by: brian@murphy.dk Signed-off-by: -
david-b@pacbell.net authored
This adds another CDC descriptor type to <linux/usb_cdc.h>; the main claim to fame for this is that some Motorola phones include it. It's not currently needed by any driver code; included for completeness. Signed-off-by:
David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
-
david-b@pacbell.net authored
A patch re-organizing some parts of root hub initialization deleted the code initializing the bus-neutral reboot/shutdown notifier for OHCI. This patch just restores that deleted code. Signed-off-by:
-
david-b@pacbell.net authored
The recent "pm_message_t" changes removed functionality from the Linux PM framework. This patch removes it from the OMAP OHCI too, removing the distinction between (previous) PM_SUSPEND_MEM and PM_SUSPEND_DISK state transitions ... now the only suspend semantics supportable are what was previously PM_SUSPEND_DISK (4) and is now "PMSG_SUSPEND" (3). From: Todd Poynor <tpoynor@mvista.com> Signed-off-by:
-
david-b@pacbell.net authored
Minor OMAP updates that somehow got dropped from previous patches. Signed-off-by:
-
Ian Campbell authored
I also needed the following on 2.6.13-rc1 without CONFIG_USB_ETH_RNDIS, symbol fs_status_desc isn't available in that case on PXA255. This builds both with and without ETH_RNDIS, but I haven't actually tested either. Signed-off-by:
Ian Campbell <icampbell@arcom.com> Signed-off-by:
-
Ian Campbell authored
Signed-off-by:
-
Luca Risolia authored
SN9C10x driver updates. Changes: + new, - removed, * cleanup, @ bugfix @ Remove bad get_ctrl()'s * Documentation updates + Add 0x0c45/0x602d to the list of SN9C10x based devices + Add support for OV7630 image sensors Signed-off-by:
Luca Risolia <luca.risolia@studio.unibo.it> Signed-off-by:
-
Michael Hund authored
below you will find one patch to hid-core.c, which lets usbhid ignore our HID devices. It would be nice, if you can apply it. Signed-off-by:
-
KAMBAROV, ZAUR authored
The length of the array desc->bitmap is 3, and not 4: Definitions involved: In drivers/usb/core/hcd.h 464 #define bitmap DeviceRemovable In drivers/usb/host/ohci-hub.c 395 struct usb_hub_descriptor *desc In drivers/usb/core/hub.h 130 struct usb_hub_descriptor { 131 __u8 bDescLength; 132 __u8 bDescriptorType; 133 __u8 bNbrPorts; 134 __u16 wHubCharacteristics; 135 __u8 bPwrOn2PwrGood; 136 __u8 bHubContrCurrent; 137 /* add 1 bit for hub status change; round to bytes */ 138 __u8 DeviceRemovable[(USB_MAXCHILDREN + 1 + 7) / 8]; 139 __u8 PortPwrCtrlMask[(USB_MAXCHILDREN + 1 + 7) / 8]; 140 } __attribute__ ((packed)); In include/linux/usb.h 306 #define USB_MAXCHILDREN (16) This defect was found automatically by Coverity Prevent, a static analysis tool. (akpm: this code should be shot. Field `bitmap' doesn't exist in struct usb_hub_descriptor. And this .c file is #included in drivers/usb/host/ohci-hcd.c, and someone somewhere #defines `bitmap' to `DeviceRemovable'. >From a maintainability POV it would be better to memset the whole array beforehand - I changed the patch to do that) Signed-off-by:Zaur Kambarov <zkambarov@coverity.com> Cc: <linux-usb-devel@lists.sourceforge.net? Signed-off-by:
-
Michael Downey authored
This driver is a basic keypress input driver for the Keyspan Digital Remote with part number UIA-11. Currently there is an older remote with part number UIA-10 which isn't supported by this driver. Support for the older UIA-10 could be added but a binary file is required to be download to the device, and I don't have that file. I also don't have a UIA-10 device so I wouldn't be able to test any of the changes. Signed-off-by:
Michael Downey <downey@zymeta.com> Signed-off-by:
-
Andrew Morton authored
drivers/usb/gadget/net2280.c: In function 'show_registers': drivers/usb/gadget/net2280.c:1501: warning: assignment discards qualifiers from pointer target type Signed-off-by:
-
Olav Kongas authored
Greg, This patch fixes the kmalloc() flags argument type in USB subsystem; hopefully all of its occurences. The patch was made against patch-2.6.12-git2 from Jun 20. Cleanup of flags for kmalloc() in USB subsystem. Signed-off-by:
Olav Kongas <ok@artecdesign.ee> Signed-off-by:
-
Olav Kongas authored
Sorry that it took so long. Here comes a cleanup patch that addresses the remarks by Alexey Dobriyan about gregkh-usb-usb-isp116x-hcd-add.patch EXCEPT the remark about the typecasting of mem_flags argument for kcalloc; this will be addressed in a later patch. OlavCleanup of isp116x-hcd. Signed off by: Olav Kongas <ok@artecdesign.ee> Signed-off-by: -
Pete Zaitcev authored
Make usbmon to print Setup packets of Control transfers. This is useful when debugging enumeration issues. This is a change to the trace format which is not fully compatible. A parser has to look at the data length word now. If that word is a character like 's', read setup packet before proceeding with data. I decided not to bump the API tag for this because not many such parsers exist at this point. Signed-off-by:
Pete Zaitcev <zaitcev@redhat.com> Signed-off-by:
-
Thomas Winischhofer authored
although 2.6.12 now contains the sisusb driver, it failes to build this driver due to a missing patch of the Makefile. From: Thomas Winischhofer <thomas@winischhofer.net> Signed-off-by: -
Duncan Sands authored
We map states 0x00 and 0x10 to the ATM_PHY_SIG_LOST flag. The current logic fails to resync the line if we get state 0x10 followed by 0x00, since we only resync the line when the state is 0x00 and the flag changed. Doubly fixed by (1) always resyncing the line when the state is 0x00 even if the state didn't change, and (2) keeping track of the last state, not just the flag. We do (2) as well as (1) in order to get better log messages. This is a tweaked version of the original patch by Aurelio Arroyo. Signed-off-by:
Duncan Sands <baldrick@free.fr> Signed-off-by:
-
Duncan Sands authored
No functional change, but less likely to break in the future. Signed-off-by:
-
Duncan Sands authored
Spotted by David Woodhouse. Signed-off-by:
-
Greg Kroah-Hartman authored
Signed-off-by: -
Ian Abbott authored
ftdi_sio: Remove redundant handling of TIOCMBIS and TIOCMBIC ioctls as they are handled in the tty layer and never reach this driver. Signed-off-by:
Ian Abbott <abbotti@mev.co.uk> Signed-off-by:
-
Ian Abbott authored
ftdi_sio: Use a single usb_device_id table and detect the type of chip programatically. The table also flags devices requiring special initialization. The patch makes the driver about 10K smaller and makes it easier to add new device IDs. Signed-off-by:
-
akpm@osdl.org authored
Signed-off-by:
-
Phil Dibowitz authored
This patch removes an unneeded subclass and protocol from the 07af/0005/100 entry in unsual_devs.h as reported by Alfred Ganz <alfred-ganz@agci.com>. Signed-off-by:
Phil Dibowitz <phil@ipom.com> Signed-off-by:
-
Greg Kroah-Hartman authored
For some reason this was not there... Signed-off-by: -
Sam Ravnborg authored
Move the protocol specific config options out to the specific protocols. With this change net/Kconfig now starts to become readable and serve as a good basis for further re-structuring. The menu structure is left almost intact, except that indention is fixed in most cases. Most visible are the INET changes where several "depends on INET" are replaced with a single ifdef INET / endif pair. Several new files were created to accomplish this change - they are small but serve the purpose that config options are now distributed out where they belongs. Signed-off-by:
Sam Ravnborg <sam@ravnborg.org> Signed-off-by:
-
Sam Ravnborg authored
Create a new top-level menu named "Networking" thus moving net related options and protocol selection way from the drivers menu and up on the top-level where they belong. To implement this all architectures has to source "net/Kconfig" before drivers/*/Kconfig in their Kconfig file. This change has been implemented for all architectures. Device drivers for ordinary NIC's are still to be found in the Device Drivers section, but Bluetooth, IrDA and ax25 are located with their corresponding menu entries under the new networking menu item. Signed-off-by:
-
Olaf Kirch authored
In some cases, we may be generating packets with a source address that qualifies as martian. This can happen when we're in the middle of setting up the network, and netfilter decides to reject a packet with an RST. The IPv4 routing code would try to print a warning and oops, because locally generated packets do not have a valid skb->mac.raw pointer at this point. Signed-off-by: -
Julian Anastasov authored
An addition to the last ipvs changes that move update_defense_level/si_meminfo to keventd: - ip_vs_random_dropentry now runs in process context and should use _bh locks to protect from softirqs - update_defense_level still needs _bh locks after si_meminfo is called, for the same purpose Signed-off-by:
Julian Anastasov <ja@ssi.bg> Signed-off-by:
-
Jesper Juhl authored
Signed-off-by:
Jesper Juhl <juhl-lkml@dif.dk> Signed-off-by:
Adrian Bunk <bunk@stusta.de> Signed-off-by:
-
