- 22 Oct, 2019 38 commits
-
-
Vivien Didelot authored
Like the dsa_switch_tree structures, the dsa_port structures will be allocated on switch registration. The SJA1105 driver is the only one accessing the dsa_port structure after the switch allocation and before the switch registration. For that reason, move switch registration prior to assigning the priv member of the dsa_port structures. Signed-off-by:
Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com>
-
Vivien Didelot authored
Instead of digging into the other dsa_switch structures of the fabric and relying too much on the dsa_to_port helper, use the new list of switch fabric ports to remap the Port VLAN Map of local bridge group members or remap the Port VLAN Table entry of external bridge group members. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Vivien Didelot authored
Instead of digging into the other dsa_switch structures of the fabric and relying too much on the dsa_to_port helper, use the new list of switch fabric ports to define the mask of the local ports allowed to receive frames from another port of the fabric. Signed-off-by:
-
Vivien Didelot authored
Since mv88e6xxx_pvt_map is a static helper, no need to return -EOPNOTSUPP if the chip has no PVT, simply silently skip the operation. Signed-off-by:
-
Vivien Didelot authored
Use the new ports list instead of iterating over switches and their ports when setting up the default CPU port. Unassign it on teardown. Now that we can iterate over multiple CPU ports, remove dst->cpu_dp. At the same time, provide a better error message for CPU-less tree. Signed-off-by:
-
Vivien Didelot authored
Use the new ports list instead of iterating over switches and their ports when looking up the first CPU port in the tree. Signed-off-by:
-
Vivien Didelot authored
Now that we have a potential list of CPU ports, make use of it instead of only configuring the master device of an unique CPU port. Signed-off-by:
-
Vivien Didelot authored
Use the new ports list instead of iterating over switches and their ports to find a port from a given node. Signed-off-by:
-
Vivien Didelot authored
Use the new ports list instead of accessing the dsa_switch array of ports when iterating over DSA ports of a switch to set up the routing table. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Vivien Didelot authored
Use the new ports list instead of iterating over switches and their ports when setting up the switches and their ports. At the same time, provide setup states and messages for ports and switches as it is done for the trees. Signed-off-by:
-
Vivien Didelot authored
Use the new ports list instead of iterating over switches and their ports when looking for a slave device from a given master interface. Signed-off-by:
-
Vivien Didelot authored
Use the new ports list instead of accessing the dsa_switch array of ports in the dsa_to_port helper. Signed-off-by:
-
Vivien Didelot authored
Add a list of switch ports within the switch fabric. This will help the lookup of a port inside the whole fabric, and it is the first step towards supporting multiple CPU ports, before deprecating the usage of the unique dst->cpu_dp pointer. In preparation for a future allocation of the dsa_port structures, return -ENOMEM in case no structure is returned, even though this error cannot be reached yet. Signed-off-by:
-
Vivien Didelot authored
Do not let the drivers access the ds->ports static array directly while there is a dsa_to_port helper for this purpose. At the same time, un-const this helper since the SJA1105 driver assigns the priv member of the returned dsa_port structure. Signed-off-by:
-
Jakub Kicinski authored
Heiner Kallweit says: ==================== The attempt to improve performance by changing the PCIe max read request size was added in the vendor driver more than 10 years back and copied to r8169 driver. In the vendor driver this has been removed long ago. Obviously it had no effect, also in my tests I didn't see any difference. Typically the max payload size is less than 512 bytes anyway, and the PCI core takes care that the maximum supported value is set. So let's remove fiddling with PCIe max read request size from r8169 too. This change allows to simplify the driver in the subsequent three patches of this series. ==================== Signed-off-by: -
Heiner Kallweit authored
We can remove rtl_hw_start_8168bef() and use rtl_hw_start_8168b() instead because setting register Config4 is done in rtl_jumbo_config(), being called from rtl_hw_start(). Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Heiner Kallweit authored
We can remove rtl_hw_start_8168dp() because it's the same as rtl_hw_start_8168dp() now. Signed-off-by:
-
Heiner Kallweit authored
r8168b_0_hw_jumbo_enable() and r8168b_0_hw_jumbo_disable() both do the same and just set PCI_EXP_DEVCTL_NOSNOOP_EN. We can simplify the code by moving this setting for RTL8168B to rtl_hw_start_8168(). Signed-off-by:
-
Heiner Kallweit authored
The attempt to improve performance by changing the PCIe max read request size was added in the vendor driver more than 10 years back and copied to r8169 driver. In the vendor driver this has been removed long ago. Obviously it had no effect, also in my tests I didn't see any difference. Typically the max payload size is less than 512 bytes anyway, and the PCI core takes care that the maximum supported value is set. So let's remove fiddling with PCIe max read request size from r8169 too. Signed-off-by:
-
Jakub Kicinski authored
Karsten Graul says: ==================== More patches to address abnormal termination processing of sockets and link groups. ==================== Signed-off-by: -
Ursula Braun authored
With the introduction of the link group termination worker there is no longer a need to postpone smc_close_active_abort() to a worker. To protect socket destruction due to normal and abnormal socket closing, the socket refcount is increased. Signed-off-by:
Ursula Braun <ubraun@linux.ibm.com> Signed-off-by:
Karsten Graul <kgraul@linux.ibm.com> Signed-off-by:
-
Ursula Braun authored
Use a worker for link group termination to guarantee process context. Signed-off-by:
-
Ursula Braun authored
If a link group and its connections must be terminated, * wake up socket waiters * do not enable buffer reuse A linkgroup might be terminated while normal connection closing is running. Avoid buffer reuse and its related LLC DELETE RKEY call, if linkgroup termination has started. And use the earliest indication of linkgroup termination possible, namely the removal from the linkgroup list. Signed-off-by:
-
Ursula Braun authored
There are lots of link group termination scenarios. Most of them still allow to inform the peer of the terminating sockets about aborting. This patch tries to call smc_close_abort() for terminating sockets. And the internal TCP socket is reset with tcp_abort(). Signed-off-by:
-
Ursula Braun authored
Usually link groups are freed delayed to enable quick connection creation for a follow-on SMC socket. Terminated link groups are freed faster. This patch makes sure, fast schedule of link group freeing is not rescheduled by a delayed schedule. And it makes sure link group freeing is not rescheduled, if the real freeing is already running. Signed-off-by:
-
Ursula Braun authored
Locking hierarchy requires that the link group conns_lock can be taken if the socket lock is held, but not vice versa. Nevertheless socket termination during abnormal link group termination should be protected by the socket lock. This patch reduces the time segments the link group conns_lock is held to enable usage of lock_sock in smc_lgr_terminate(). Signed-off-by:
-
Ursula Braun authored
When a link group is to be terminated, it is sufficient to hold the lgr lock when unlinking the link group from its list. Move the lock-protected link group unlinking into smc_lgr_terminate(). Signed-off-by:
-
Ursula Braun authored
The resources for a terminated socket are being cleaned up. This patch makes sure * no more data is received for an actively terminated socket * no more data is sent for an actively or passively terminated socket Signed-off-by:
-
Jakub Kicinski authored
Ido Schimmel says: ==================== Vadim says: This patch set extends the size of QSFP EEPROM for the cable types SSF-8436 and SFF-8636 from 256 bytes to 640 bytes. This allows ethtool to show correct information for these cable types (more details below). Patch #1 adds a macro that computes the EEPROM page number from the provided offset specified in the request. Patch #2 teaches the driver to access the information stored in the upper pages of the QSFP memory map. Details and examples: SFF-8436 specification defines pages 0, 1, 2 and 3. Page 0 contains lower memory page offsets (from 0x00 to 0x7f) and upper page offsets (from 0x80 to 0xfe). Upper pages 1, 2 and 3 are optional and can be empty. Page 1 is provided if upper page 0 byte 0xc3 bit 6 is set. Page 2 is provided if upper page 0 byte 0xc3 bit 7 is set. Page 3 is provided if lower page 0 byte 0x02 bit 2 is cleared. Offset 0xc3 for the upper page is provided as 0x43 = 0xc3 - 0x80. As a result of exposing 256 bytes only, ethtool shows wrong information for pages 1, 2 and 3. In the below hex dump from ethtool for a cable compliant to SFF-8636 specification, it can be seen that EEPROM of this device contains optical diagnostic page (lower page 0 byte 0x02 bit 2 is cleared), but it is not exposed, as the length defined for this type is 256 bytes. $ ethtool -m sfp42 hex on Offset Values ------ ------ 0x0000: 11 07 00 ff 00 ff 00 00 00 55 55 00 00 00 00 00 0x0010: 00 00 00 00 00 00 2a 90 00 00 82 ae 00 00 00 00 0x0020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0050: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00 0x0060: 00 00 ff 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0080: 11 8c 0c 80 00 00 00 00 00 00 00 05 ff 00 00 23 0x0090: 00 00 32 00 4d 65 6c 6c 61 6e 6f 78 20 20 20 20 0x00a0: 20 20 20 20 00 00 02 c9 4d 4d 41 31 42 30 30 2d 0x00b0: 53 53 31 20 20 20 20 20 41 32 42 68 0b b8 46 05 0x00c0: 02 07 f5 9e 4d 54 31 38 33 34 46 54 30 33 38 34 0x00d0: 36 20 20 20 31 38 30 37 30 33 00 00 0c 10 67 c2 0x00e0: 38 32 36 46 4d 41 32 32 36 49 30 31 31 35 20 20 0x00f0: 00 00 00 00 00 00 00 00 00 00 01 00 0e 00 00 00 After changing the length returned by get_module_info() callback from 256 bytes to 640 bytes, the upper pages 1, 2 and 3 are exposed by ethtool. In the below hex dump from the same cable it can be seen that the optical diagnostic page (page 3, from offset 0x0200) has non-zero data. $ ethtool -m sfp42 hex on Offset Values ------ ------ 0x0000: 11 07 00 ff 00 ff 00 00 00 55 55 00 00 00 00 00 0x0010: 00 00 00 00 00 00 27 79 00 00 82 c5 00 00 00 00 0x0020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0050: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00 0x0060: 00 00 ff 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0080: 11 8c 0c 80 00 00 00 00 00 00 00 05 ff 00 00 23 0x0090: 00 00 32 00 4d 65 6c 6c 61 6e 6f 78 20 20 20 20 0x00a0: 20 20 20 20 00 00 02 c9 4d 4d 41 31 42 30 30 2d 0x00b0: 53 53 31 20 20 20 20 20 41 32 42 68 0b b8 46 05 0x00c0: 02 07 f5 9e 4d 54 31 38 33 34 46 54 30 33 38 34 0x00d0: 36 20 20 20 31 38 30 37 30 33 00 00 0c 10 67 c2 0x00e0: 38 32 36 46 4d 41 32 32 36 49 30 31 31 35 20 20 0x00f0: 00 00 00 00 00 00 00 00 00 00 01 00 0e 00 00 00 0x0100: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0110: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0120: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0130: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0140: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0150: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0160: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0170: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0180: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0190: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x01a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x01b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x01c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x01d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x01e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x01f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0200: 50 00 f6 00 46 00 00 00 00 00 00 00 00 00 00 00 0x0210: 88 b8 79 18 87 5a 7a 76 00 00 00 00 00 00 00 00 0x0220: 00 00 00 00 00 00 00 00 00 00 18 30 0e 61 60 b7 0x0230: 87 71 01 d3 43 e2 03 a5 10 9a 0a ba 0f a0 0b b8 0x0240: 87 71 02 d4 43 e2 05 a5 00 00 00 00 00 00 00 00 0x0250: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0260: a7 03 00 00 00 00 00 00 00 00 44 44 22 22 11 11 0x0270: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 And 'ethtool -m sfp42' shows the real values for the below fields, while before it exposed zeros for these fields: Laser bias current high alarm threshold : 8.500 mA Laser bias current low alarm threshold : 5.492 mA Laser bias current high warning threshold : 8.000 mA Laser bias current low warning threshold : 6.000 mA Laser output power high alarm threshold : 3.4673 mW / 5.40 dBm Laser output power low alarm threshold : 0.0724 mW / -11.40 dBm Laser output power high warning threshold : 1.7378 mW / 2.40 dBm Laser output power low warning threshold : 0.1445 mW / -8.40 dBm Module temperature high alarm threshold : 80.00 degrees C / 176.00 F Module temperature low alarm threshold : -10.00 degrees C / 14.00 F Module temperature high warning threshold : 70.00 degrees C / 158.00 F Module temperature low warning threshold : 0.00 degrees C / 32.00 F Module voltage high alarm threshold : 3.5000 V Module voltage low alarm threshold : 3.1000 V ==================== Signed-off-by: -
Vadim Pasternak authored
Extend the size of QSFP EEPROM for the cable types SSF8436 and SFF8636 from 256 to 640 bytes in order to expose all the EEPROM pages by ethtool. For SFF-8636 and SFF-8436 specifications, the driver exposes 256 bytes of data for ethtool's get_module_eeprom() callback. This is because the driver uses the below defines to specify SFF module length in ethtool's get_module_info() callback: 'ETH_MODULE_SFF_8636_LEN' and 'ETH_MODULE_SFF_8436_LEN' (both are 256). As a result of exposing 256 bytes only, ethtool shows wrong "zero" info for pages 1, 2, 3. The patch changes the length returned by callback for get_module_info() to the values from the next defines: 'ETH_MODULE_SFF_8636_MAX_LEN' and 'ETH_MODULE_SFF_8436_MAX_LEN' (both are 640) to allow exposing of upper page 1, 2 and 3. Signed-off-by:
Vadim Pasternak <vadimp@mellanox.com> Acked-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
Vadim Pasternak authored
Provide a macro for getting QSFP module EEPROM page number from the optional upper page number row offset, specified in request. Signed-off-by:
-
Juergen Gross authored
Do some cleanup of the netback init and deinit code: - add an omnipotent queue deinit function usable from xenvif_disconnect_data() and the error path of xenvif_connect_data() - only install the irq handlers after initializing all relevant items (especially the kthreads related to the queue) - there is no need to use get_task_struct() after creating a kthread and using put_task_struct() again after having stopped it. - use kthread_run() instead of kthread_create() to spare the call of wake_up_process(). Signed-off-by:
Juergen Gross <jgross@suse.com> Reviewed-by:
Paul Durrant <pdurrant@gmail.com> Signed-off-by:
-
Jakub Kicinski authored
Hayes Wang says: ==================== Support loading the firmware of the PHY with the type of RTL_FW_PHY_NC. ==================== Signed-off-by: -
Hayes Wang authored
Support the firmware of PHY NC which is used to fix the issue found for PHY. Currently, only RTL_VER_04, RTL_VER_05, and RTL_VER_06 need it. The order of loading PHY firmware would be RTL_FW_PHY_START RTL_FW_PHY_NC RTL_FW_PHY_STOP The RTL_FW_PHY_START/RTL_FW_PHY_STOP are used to lock/unlock the PHY, and set/clear the patch key from the firmware file. Signed-off-by:
Hayes Wang <hayeswang@realtek.com> Signed-off-by:
-
Hayes Wang authored
Move r8153_patch_request() forward for later patch. Signed-off-by:
-
Hayes Wang authored
Make sure @fw_offset field of struct fw_mac is more than the size of struct fw_mac. Signed-off-by:
-
Hayes Wang authored
The struct fw_type_1 is used by MAC only, so rename it to a meaningful one. Besides, adjust two messages. Replace "load xxx fail" with "check xxx fail" Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueJakub Kicinski authored
Jeff Kirsher says: ==================== 1GbE Intel Wired LAN Driver Updates 2019-10-21 This series contains updates to e1000e and igc only. Sasha adds stream control transmission protocol (SCTP) CRC checksum support for igc. Also added S0ix support to the e1000e driver. Then added multicast support by adding the address list to the MTA table and providing the option for IPv6 address for igc. In addition, added receive checksum support to igc as well. Lastly, cleaned up some code that was not fully implemented yet for the VLAN filter table array. v2: Dropped patch 1 & 2 from the original series. Patch 1 is being sent to 'net' tree as a fix and patch 2 implementation needs to be re-worked. Updated the patch to add support for S0ix to fix the reverse Xmas tree issues and made the entry/exit functions void since they constantly returned success. All based on community feedback. v3: Cleaned up patch 4 of the series based on feedback from the community. Cleaned up a stray comma in a code comment and removed the 'inline' of a function that would be inlined by the compiler anyways. ==================== Signed-off-by:
-
- 21 Oct, 2019 2 commits
-
-
Davide Caratti authored
Use tcf_tm_dump(), instead of an open coded variant (no functional change in this patch). Signed-off-by:
Davide Caratti <dcaratti@redhat.com> Acked-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Heiner Kallweit says: ==================== net: phy: marvell: support downshift as PHY tunable So far downshift is implemented for one small use case only and can't be controlled from userspace. So let's implement this feature properly as a PHY tunable so that it can be controlled via ethtool. ==================== Signed-off-by:
-
