Some USB ports can support host and device operation. We add the dr_mode
property (as found in Freescale) for this.

One USB port has a 'legacy mode', left over from the days of pre-Tegra
chips. I don't believe this is actually used, except that we must know
to turn this off in the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch adds device tree binding of digital microphone to PAZ00
board.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Olof Johansson <olof@lixom.net>

This enables HW performance measurements, and usage of the "perf" tool.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Cardhu uses Tegra's SD ports as follows:
SDMMC1: User SD slot, with GPIOs for power, CD, and WP.
SDMMC2: Not used
SDMMC3: WiFi (currently disabled pending future investigation)
SDMMC4: Internal eMMC
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch is adding device tree support of headset autodetection on PAZ00 board.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch adds initial device tree support of ALC5632 sound codec and
machine driver for PAZ00 board. The implementation is based on the WM8903 codec.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Olof Johansson <olof@lixom.net>

The Tegra PMC (Power Management Controller) interfaces with an external
PMU (Power Management Unit), and controls wake-up from sleep modes.

This initial binding is the bare minimum required to control the PMC's
inversion of the PMU's interrupt signal.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Add complete bindings to instantiate and configure the codec and
top-level audio complex on all currently supported boards using the
Tegra+WM8903 audio driver.

On those boards, disable the I2S2 controller since it isn't used.

On boards not using the WM8903 codec, disable all the audio devices;
they can be re-enabled once the relevant codec and ASoC machine drivers
have been ported to device-tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

This will allow the sound node to refer to the I2S controllers by name
when creating phandles.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Adjust the dma-channel property name to match the binding implemented by
the driver. The binding was implemented and documented in a
separate change to the ASoC tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Document binding, and add the node to tegra*.dtsi.

The driver isn't actually instantiated from this node yet, but the I2S
binding will rely on being able to refer to the APB DMA node using a
phandle.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The Tegra30 GPIO controller has one more bank than Tegra20, and hence
has one more interrupt.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>

The new content matches tegra20.dtsi, and is < 80 columns.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>

Document the required reg and interrupts properties.
Add a complete example.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>

Timings for the T25 version of seaboard, only one memory manufacturer
and timing table (two speeds).
Signed-off-by: Olof Johansson <olof@lixom.net>

Device tree bindings for the EMC tables on tegra.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>

There are few important bug fixes for LogFS

* tag 'for-linus' of git://github.com/prasad-joshi/logfs_upstream:
  Logfs: Allow NULL block_isbad() methods
  logfs: Grow inode in delete path
  logfs: Free areas before calling generic_shutdown_super()
  logfs: remove useless BUG_ON
  MAINTAINERS: Add Prasad Joshi in LogFS maintiners
  logfs: Propagate page parameter to __logfs_write_inode
  logfs: set superblock shutdown flag after generic sb shutdown
  logfs: take write mutex lock during fsync and sync
  logfs: Prevent memory corruption
  logfs: update page reference count for pined pages

Fix up conflict in fs/logfs/dev_mtd.c due to semantic change in what
"mtd->block_isbad" means in commit f2933e86: "Logfs: Allow NULL
block_isbad() methods" clashing with the abstraction changes in the
commits 7086c19d: "mtd: introduce mtd_block_isbad interface" and
d58b27ed: "logfs: do not use 'mtd->block_isbad' directly".

This resolution takes the semantics from commit f2933e86, and just
makes mtd_block_isbad() return zero (false) if the 'block_isbad'
function is NULL.  But that also means that now "mtd_can_have_bb()"
always returns 0.

Now, "mtd_block_markbad()" will obviously return an error if the
low-level driver doesn't support bad blocks, so this is somewhat
non-symmetric, but it actually makes sense if a NULL "block_isbad"
function is considered to mean "I assume that all my blocks are always
good".

Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (w83627ehf) Disable setting DC mode for pwm2, pwm3 on NCT6776F
  hwmon: (sht15) fix bad error code
  MAINTAINERS: Drop maintainer for MAX1668 hwmon driver
  MAINTAINERS: Add hwmon entries for Wolfson
  hwmon: (f71805f) Fix clamping of temperature limits

Here are some fixes to the pin control system that has accumulated since
-rc1.  Mainly Tony Lindgren fixed the module load/unload logic and the
rest are minor fixes and documentation.

* 'for-torvalds' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: add checks for empty function names
  pinctrl: fix pinmux_hog_maps when ctrl_dev_name is not set
  pinctrl: fix some pinmux typos
  pinctrl: free debugfs entries when unloading a pinmux driver
  pinctrl: unbreak error messages
  Documentation/pinctrl: fix a few syntax errors in code examples
  pinctrl: fix pinconf_pins_show iteration

Here are some tty/serial patches for 3.3-rc1

Big thing here is the movement of the 8250 serial drivers to their own
directory, now that the patch churn has calmed down.

Other than that, only minor stuff (omap patches were reverted as they
were found to be wrong), and another broken driver removed from the
system.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* tag 'tty-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: Kill off Moorestown code
  Revert "tty: serial: OMAP: ensure FIFO levels are set correctly in non-DMA mode"
  Revert "tty: serial: OMAP: transmit FIFO threshold interrupts don't wake the chip"
  serial: Fix wakeup init logic to speed up startup
  docbook: don't use serial_core.h in device-drivers book
  serial: amba-pl011: lock console writes against interrupts
  amba-pl011: do not disable RTS during shutdown
  tty: serial: OMAP: transmit FIFO threshold interrupts don't wake the chip
  tty: serial: OMAP: ensure FIFO levels are set correctly in non-DMA mode
  omap-serial: make serial_omap_restore_context depend on CONFIG_PM_RUNTIME
  omap-serial :Make the suspend/resume functions depend on CONFIG_PM_SLEEP.
  TTY: fix UV serial console regression
  jsm: Fixed EEH recovery error
  Updated TTY MAINTAINERS info
  serial: group all the 8250 related code together

Here are a bunch of USB patches for 3.3-rc1.

Nothing major, largest thing here is the removal of some drivers that
did not work at all.  Other than that, the normal collection of bugfixes
and new device ids.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* tag 'usb-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (52 commits)
  uwb & wusb: fix kconfig error
  USB: Realtek cr: fix autopm scheduling while atomic
  USB: ftdi_sio: Add more identifiers
  xHCI: Cleanup isoc transfer ring when TD length mismatch found
  usb: musb: omap2430: minor cleanups.
  qcaux: add more Pantech UML190 and UML290 ports
  Revert "drivers: usb: Fix dependency for USB_HWA_HCD"
  usb: mv-otg - Fix build if CONFIG_USB is not set
  USB: cdc-wdm: Avoid hanging on interface with no USB_CDC_DMM_TYPE
  usb: add support for STA2X11 host driver
  drivers: usb: Fix dependency for USB_HWA_HCD
  kernel-doc: fix new warning in usb.h
  USB: OHCI: fix new compiler warnings
  usb: serial: kobil_sct: fix compile warning:
  drivers/usb/host/ehci-fsl.c: add missing iounmap
  USB: cdc-wdm: better allocate a buffer that is at least as big as we tell the USB core
  USB: cdc-wdm: call wake_up_all to allow driver to shutdown on device removal
  USB: cdc-wdm: use two mutexes to allow simultaneous read and write
  USB: cdc-wdm: updating desc->length must be protected by spin_lock
  USB: usbsevseg: fix max length
  ...

1) Setting link attributes can modify the size of the attributes that
   would be reported on a subsequent getlink netlink operation,
   therefore min_ifinfo_dump_size needs to be adjusted.  From Stefan
   Gula.

2) Resegmentation of TSO frames while trimming can violate invariants
   expected by callers, namely that the number of segments can only stay
   the same or decrease, never increase.  If MSS changes, however, we
   can trim data but then end up with more segments.  Fix this by only
   segmenting to the MSS already recorded in the SKB.  That's the
   simplest fix for now and if we want to get more fancy in the future
   that's a more involved change.

   This probably explains some retransmit counter inaccuracies.

   From Neal Cardwell.

3) Fix too-many-wakeups in POLL with AF_UNIX sockets, from Eric Dumazet.

4) Fix CAIF crashes wrt.  namespace handling.  From Eric Dumazet and
   Eric W. Biederman.

5) TCP port selection fixes from Flavio Leitner.

6) More socket memory cgroup build fixes in certain randonfig
   situations.  From Glauber Costa.

7) Fix TCP memory sysctl regression reported by Ingo Molnar, also from
   Glauber Costa.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  af_unix: fix EPOLLET regression for stream sockets
  tcp: fix tcp_trim_head() to adjust segment count with skb MSS
  net/tcp: Fix tcp memory limits initialization when !CONFIG_SYSCTL
  net caif: Register properly as a pernet subsystem.
  netns: Fail conspicously if someone uses net_generic at an inappropriate time.
  net: explicitly add jump_label.h header to sock.h
  net: RTNETLINK adjusting values of min_ifinfo_dump_size
  ipv6: Fix ip_gre lockless xmits.
  xen-netfront: correct MAX_TX_TARGET calculation.
  netns: fix net_alloc_generic()
  tcp: bind() optimize port allocation
  tcp: bind() fix autoselection to share ports
  l2tp: l2tp_ip - fix possible oops on packet receive
  iwlwifi: fix PCI-E transport "inta" race
  mac80211: set bss_conf.idle when vif is connected
  mac80211: update oper_channel on ibss join

This fixes an integration issue with the regulator device tree bindings
which shook out in -rc.  The bindings were overly enthusiatic when
deciding to set a voltage on a regulator and would try to set zero volts
on an unconfigured regulator which isn't supported.

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: Set apply_uV only when min and max voltages are defined

Commit 0884d7aa (AF_UNIX: Fix poll blocking problem when reading from
a stream socket) added a regression for epoll() in Edge Triggered mode
(EPOLLET)

Appropriate fix is to use skb_peek()/skb_unlink() instead of
skb_dequeue(), and only call skb_unlink() when skb is fully consumed.

This remove the need to requeue a partial skb into sk_receive_queue head
and the extra sk->sk_data_ready() calls that added the regression.

This is safe because once skb is given to sk_receive_queue, it is not
modified by a writer, and readers are serialized by u->readlock mutex.

This also reduce number of spinlock acquisition for small reads or
MSG_PEEK users so should improve overall performance.
Reported-by: Nick Mathewson <nickm@freehaven.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Alexey Moiseytsev <himeraster@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit fixes tcp_trim_head() to recalculate the number of
segments in the skb with the skb's existing MSS, so trimming the head
causes the skb segment count to be monotonically non-increasing - it
should stay the same or go down, but not increase.

Previously tcp_trim_head() used the current MSS of the connection. But
if there was a decrease in MSS between original transmission and ACK
(e.g. due to PMTUD), this could cause tcp_trim_head() to
counter-intuitively increase the segment count when trimming bytes off
the head of an skb. This violated assumptions in tcp_tso_acked() that
tcp_trim_head() only decreases the packet count, so that packets_acked
in tcp_tso_acked() could underflow, leading tcp_clean_rtx_queue() to
pass u32 pkts_acked values as large as 0xffffffff to
ca_ops->pkts_acked().

As an aside, if tcp_trim_head() had really wanted the skb to reflect
the current MSS, it should have called tcp_set_skb_tso_segs()
unconditionally, since a decrease in MSS would mean that a
single-packet skb should now be sliced into multiple segments.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

sysctl_tcp_mem() initialization was moved to sysctl_tcp_ipv4.c
in commit 3dc43e3e, since it
became a per-ns value.

That code, however, will never run when CONFIG_SYSCTL is
disabled, leading to bogus values on those fields - causing hung
TCP sockets.

This patch fixes it by keeping an initialization code in
tcp_init(). It will be overwritten by the first net namespace
init if CONFIG_SYSCTL is compiled in, and do the right thing if
it is compiled out.

It is also named properly as tcp_init_mem(), to properly signal
its non-sysctl side effect on TCP limits.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Glauber Costa <glommer@parallels.com>
Cc: David S. Miller <davem@davemloft.net>
Link: http://lkml.kernel.org/r/4F22D05A.8030604@parallels.com
[ renamed the function, tidied up the changelog a bit ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  [S390] dasd: revalidate server for new pathgroup
  [S390] dasd: revert LCU optimization
  [S390] cleanup entry point definition

* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: generic atomic64 support

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  vmwgfx: Fix assignment in vmw_framebuffer_create_handle
  drm/radeon/kms: Fix device tree linkage of i2c buses
  drm: Pass the real error code back during GEM bo initialisation
  Revert "drm/i810: cleanup reclaim_buffers"

NFS client bugfixes for Linux 3.3 (pull 3)

* tag 'nfs-for-3.3-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  SUNRPC: Fix machine creds in generic_create_cred and generic_match

Power management fix for 3.3-rc2

Fix for a hibernate (s2disk) regression introduced during the 3.2
merge window that causes s2disk to trigger BUG_ON() in
freeze_workqueues_begin() if there is not enough swap space to save
the image.

* tag 'pm-fix-for-3.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM / Hibernate: Fix s2disk regression related to freezing workqueues

The assignment of handle in vmw_framebuffer_create_handle doesn't actually do anything useful and is incorrectly assigning an integer value to a pointer argument. It appears that this is a typo and should be dereferencing handle rather than assigning to it directly. This fixes a bug where an undefined handle value is potentially returned to user-space.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Reviewed-by: Jakob Bornecrantz<jakob@vmware.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

Properly set the parent device of i2c buses before registering them so
that they will show at the right place in the device tree (rather than
in /sys/devices directly.)
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Dave Airlie <airlied@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

In particular, I found I was hitting the max-file limit in the VFS,
and the EFILE was being magically transformed into ENOMEM. Confusion
reigns.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This reverts commit 87499ffd.

Where is that paper bag ... ah here.

I've failed to take an odd interaction between my other cleanups and
this reclaim_buffers patch into account and also failed to properly
test it. Looks like there are more dragons and hidden trapdoors in the
drm release path than actual lines of code.

Until I get a clue, let's just revert this.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>

NCT6776F only supports pwm mode for pwm2 and pwm3. Return error if an attempt
is made to set those pwm channels to DC mode.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>

Commit 2aede851

  PM / Hibernate: Freeze kernel threads after preallocating memory

introduced a mechanism by which kernel threads were frozen after
the preallocation of hibernate image memory to avoid problems with
frozen kernel threads not responding to memory freeing requests.
However, it overlooked the s2disk code path in which the
SNAPSHOT_CREATE_IMAGE ioctl was run directly after SNAPSHOT_FREE,
which caused freeze_workqueues_begin() to BUG(), because it saw
that worqueues had been already frozen.

Although in principle this issue might be addressed by removing
the relevant BUG_ON() from freeze_workqueues_begin(), that would
reintroduce the very problem that commit 2aede851
attempted to avoid into that particular code path.  For this reason,
to fix the issue at hand, introduce thaw_kernel_threads() and make
the SNAPSHOT_FREE ioctl execute it.

Special thanks to Srivatsa S. Bhat for detailed analysis of the
problem.
Reported-and-tested-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: stable@kernel.org

When no platform data was supplied, returned error code was 0.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: stable@vger.kernel.org # 2.6.32+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>

Merge tag 'driver-core-3.3-rc1-bugfixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Here are some patches for the 3.3-rc1 tree.

It contains the removal of the sysdev code, now that all users of it are
gone, as well as some sysfs bugfixes that have been reported by users.
There are also some documentation updates here as well.

* tag 'driver-core-3.3-rc1-bugfixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  sysfs: Complain bitterly about attempts to remove files from nonexistent directories.
  stable: update documentation to ask for kernel version
  base/core.c:fix typo in comment in function device_add
  Documentation: devres: add allocation functions to list of supported calls
  Documentation update for the driver model core
  kernel-doc: fix new warnings in driver-core
  kernel-doc: fix new warnings in debugfs
  kernel-doc: fix new warnings in device.h
  driver core: remove drivers/base/sys.c and include/linux/sysdev.h