Change all the code that deals directly with ICMPv6 type and code
values to use u8 instead of a signed int as that's the actual data
type.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes this compile error on s390:

  CC      drivers/net/ks8842.o
drivers/net/ks8842.c: In function 'ks8842_select_bank':
drivers/net/ks8842.c:124: error: implicit declaration of function 'iowrite16'
drivers/net/ks8842.c: In function 'ks8842_write8':
drivers/net/ks8842.c:131: error: implicit declaration of function 'iowrite8'

Cc: Richard Rojfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes this compile error on s390:

drivers/net/can/sja1000/sja1000_platform.c: In function 'sp_read_reg':
drivers/net/can/sja1000/sja1000_platform.c:42: error: implicit declaration of function 'ioread8'
drivers/net/can/sja1000/sja1000_platform.c: In function 'sp_write_reg':
drivers/net/can/sja1000/sja1000_platform.c:47: error: implicit declaration of function 'iowrite8'
drivers/net/can/sja1000/sja1000_platform.c: In function 'sp_probe':
drivers/net/can/sja1000/sja1000_platform.c:79: error: implicit declaration of function 'ioremap_nocache'

Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure all functions run firmware init handshake.

If PCI function 0 fails to initialize firmware, mark the
state failed so that other functions on the same board
bail out quickly instead of waiting 30s for firmware
handshake.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

wrap pci suspend() and resume() with CONFIG_PM check.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As noticed by Trk Edwin <edwintorok@gmail.com>:

Compiling the kernel with clang has shown this warning:

net/netfilter/xt_rateest.c:69:16: warning: self-comparison always results in a
constant value
                        ret &= pps2 == pps2;
                                    ^
Looking at the code:
if (info->flags & XT_RATEEST_MATCH_BPS)
            ret &= bps1 == bps2;
        if (info->flags & XT_RATEEST_MATCH_PPS)
            ret &= pps2 == pps2;

Judging from the MATCH_BPS case it seems to be a typo, with the intention of
comparing pps1 with pps2.

http://bugzilla.kernel.org/show_bug.cgi?id=13535Signed-off-by: Patrick McHardy <kaber@trash.net>

Commit v2.6.29-rc5-872-gacc738fe ("xtables: avoid pointer to self")
forgot to copy the initial quota value supplied by iptables into the
private structure, thus counting from whatever was in the memory
kmalloc returned.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>

Signed-off-by: Patrick McHardy <kaber@trash.net>

net/netfilter/xt_NFQUEUE.c:46:9: warning: incorrect type in assignment (different base types)
net/netfilter/xt_NFQUEUE.c:46:9:    expected unsigned int [unsigned] [usertype] ipaddr
net/netfilter/xt_NFQUEUE.c:46:9:    got restricted unsigned int
net/netfilter/xt_NFQUEUE.c:68:10: warning: incorrect type in assignment (different base types)
net/netfilter/xt_NFQUEUE.c:68:10:    expected unsigned int [unsigned] <noident>
net/netfilter/xt_NFQUEUE.c:68:10:    got restricted unsigned int
net/netfilter/xt_NFQUEUE.c:69:10: warning: incorrect type in assignment (different base types)
net/netfilter/xt_NFQUEUE.c:69:10:    expected unsigned int [unsigned] <noident>
net/netfilter/xt_NFQUEUE.c:69:10:    got restricted unsigned int
net/netfilter/xt_NFQUEUE.c:70:10: warning: incorrect type in assignment (different base types)
net/netfilter/xt_NFQUEUE.c:70:10:    expected unsigned int [unsigned] <noident>
net/netfilter/xt_NFQUEUE.c:70:10:    got restricted unsigned int
net/netfilter/xt_NFQUEUE.c:71:10: warning: incorrect type in assignment (different base types)
net/netfilter/xt_NFQUEUE.c:71:10:    expected unsigned int [unsigned] <noident>
net/netfilter/xt_NFQUEUE.c:71:10:    got restricted unsigned int

net/netfilter/xt_cluster.c:20:55: warning: incorrect type in return expression (different base types)
net/netfilter/xt_cluster.c:20:55:    expected unsigned int
net/netfilter/xt_cluster.c:20:55:    got restricted unsigned int const [usertype] ip
net/netfilter/xt_cluster.c:20:55: warning: incorrect type in return expression (different base types)
net/netfilter/xt_cluster.c:20:55:    expected unsigned int
net/netfilter/xt_cluster.c:20:55:    got restricted unsigned int const [usertype] ip
Signed-off-by: Patrick McHardy <kaber@trash.net>

The RCU protected conntrack hash lookup only checks whether the entry
has a refcount of zero to decide whether it is stale. This is not
sufficient, entries are explicitly removed while there is at least
one reference left, possibly more. Explicitly check whether the entry
has been marked as dying to fix this.
Signed-off-by: Patrick McHardy <kaber@trash.net>

New connection tracking entries are inserted into the hash before they
are fully set up, namely the CONFIRMED bit is not set and the timer not
started yet. This can theoretically lead to a race with timer, which
would set the timeout value to a relative value, most likely already in
the past.

Perform hash insertion as the final step to fix this.
Signed-off-by: Patrick McHardy <kaber@trash.net>

death_by_timeout() might delete a conntrack from hash list
and insert it in dying list.

 nf_ct_delete_from_lists(ct);
 nf_ct_insert_dying_list(ct);

I believe a (lockless) reader could *catch* ct while doing a lookup
and miss the end of its chain.
(nulls lookup algo must check the null value at the end of lookup and
should restart if the null value is not the expected one.
cf Documentation/RCU/rculist_nulls.txt for details)

We need to change nf_conntrack_init_net() and use a different "null" value,
guaranteed not being used in regular lists. Choose very large values, since
hash table uses [0..size-1] null values.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>

When a packet is greater than ETH_ZLEN, we end up assigning the
boolean result of a comparison to the size we unmap.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Our RX rings are always full, there is no need to check whether
we need to fill them or not. If we fail to allocate a new socket
buffer, the incoming packet is dropped an the ring remains full.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

This check that verifies that the LSO header along with control
segment and first data segment do not cross 128 bytes is no longer
required.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

When closing the port, we stop all transmit queues under the transmit
lock. It ensures that we will not attempt to transmit new packets after
the physical port was closed.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

After we moved to be a multi queue device, need to stop/start
all of our transmit queues.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

We don't need this check in the transmit function
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reporting the counter's value through 'ethtool -S'
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

The host-side CDC subset driver is binding more specifically
than it should ... only to PXA 210/25x/26x Linux-USB gadgets.

Loosen that restriction to match the gadget driver driver.
This will various PXA 27x and PXA 3xx devices happier when
talking to Linux hosts, potentially others.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Tested-by: Aric D. Blumer <aric@sdgsystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We cannot sleep in ql_reset_work under spinlock, unlock before sleep,
relock after.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't drop route if we're not caching	

	I recently got a report of an oops on a route lookup.  Maxime was
testing what would happen if route caching was turned off (doing so by setting
making rt_caching always return 0), and found that it triggered an oops.  I
looked at it and found that the problem stemmed from the fact that the route
lookup routines were returning success from their lookup paths (which is good),
but never set the **rp pointer to anything (which is bad).  This happens because
in rt_intern_hash, if rt_caching returns false, we call rt_drop and return 0.
This almost emulates slient success.  What we should be doing is assigning *rp =
rt and _not_ dropping the route.  This way, during slow path lookups, when we
create a new route cache entry, we don't immediately discard it, rather we just
don't add it into the cache hash table, but we let this one lookup use it for
the purpose of this route request.  Maxime has tested and reports it prevents
the oops.  There is still a subsequent routing issue that I'm looking into
further, but I'm confident that, even if its related to this same path, this
patch makes sense to take.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove duplicates, a stray merge conflict marker, and an entry for a file
which doesn't exist, and move one entry to its correct alphabetical place.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

When I disallowed interfering with stations on non-AP interfaces,
I not only forget mesh but also managed interfaces which need
this for the authorized flag. Let's actually validate everything
properly.

This fixes an nl80211 regression introduced by the interfering,
under which wpa_supplicant -Dnl80211 could not properly connect.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Mesh Point interfaces can also set parameters, for example plink_open is
used to manually establish peer links from user-space (currently via
iw).  Add Mesh Point to the check in nl80211_set_station.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commit b2a151a288 added a check that prevents adding or deleting
stations on non-AP interfaces.  Adding and deleting stations is
supported for Mesh Point interfaces, so add Mesh Point to that check as
well.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

73ca5203
(ath5k: remove conf->beacon_int usage)
removed bintval setting from ath5k_config. We need to init the
interval earlier and don't touch it in add_interface anymore.

Otherwise it will be set only once by upper layer through
bss_info_changed but not on second and further hostap executions.

We ended up having bintval 1000 which rendered the AP useless on
many clients.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We want to put the chip into FULL SLEEP state, when we are disabling the
radio, but the the current code always change it to AWAKE/NETWORK SLEEP.

Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

"rfkill: rewrite" incorrectly reversed
the meaning of 'state' in acer_rfkill_update() when it changed
rfkill_force_state() to rfkill_set_sw_state().  Fix it.
Signed-off-by: Troy Moure <twmoure@szypr.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This reverts 'ath5k: remove dummy PCI "retry timeout" fix' on the
same theory as in 'ath9k: Fix PCI FATAL interrupts by restoring
RETRY_TIMEOUT disabling'.
Reported-by: Bob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This information allows userspace to implement a hybrid policy where
it can store the rfkill soft-blocked state in platform non-volatile
storage if available, and if not then file-based storage can be used.

Some users prefer platform non-volatile storage because of the behaviour
when dual-booting multiple versions of Linux, or if the rfkill setting
is changed in the BIOS setting screens, or if the BIOS responds to
wireless-toggle hotkeys itself before the relevant platform driver has
been loaded.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This will respect state changes over hibernation, e.g. if the user
disables the wireless in the BIOS setup screen.

It reveals an issue where ACPI silently kills the wireless on
suspend.  Normally, the BIOS restores the correct state from
non-volatile storage on boot.  But when hibernation is aborted,
the wireless would remain killed.  Fortunately we can work around
this in the resume handler by simply writing back the same value we
read from NVS.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The setting of the "persistent" flag is also made more explicit using
a new rfkill_init_sw_state() function, instead of special-casing
rfkill_set_sw_state() when it is called before registration.

Suspend is a bit of a corner case so we try to get away without adding
another hack to rfkill-input - it's going to be removed soon.
If the state does change over suspend, users will simply have to prod
rfkill-input twice in order to toggle the state.

Userspace policy agents will be able to implement a more consistent user
experience.  For example, they can avoid the above problem if they
toggle devices individually.  Then there would be no "global state"
to get out of sync.

Currently there are only two rfkill drivers with persistent soft-blocked
state.  thinkpad-acpi already checks the software state on resume.
eeepc-laptop will require modification.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
CC: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If we return after fiddling with the state, userspace will see the
wrong state and rfkill_set_sw_state() won't work until the next call to
rfkill_set_block().  At the moment rfkill_set_block() will always be
called from rfkill_resume(), but this will change in future.

Also, presumably the point of this test is to avoid bothering devices
which may be suspended.  If we don't want to call set_block(), we
probably don't want to call query() either :-).
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

An earlier commit, 'ath9k: remove dummy PCI "retry timeout" fix', removed
code that was documented to disable RETRY_TIMEOUT register (PCI reg
0x41) since it was claimed to be a no-op. However, it turns out that
there are some combinations of hosts and ath9k-supported cards for
which this is not a no-op (reg 0x41 has value 0x80, not 0) and this
code (or something similar) is needed. In such cases, the driver may
be next to unusable due to very frequent PCI FATAL interrupts from the
card.

Reverting the earlier commit, i.e., restoring the RETRY_TIMEOUT
disabling, seems to resolve the issue. Since the removal of this code
was not based on any known issue and was purely a cleanup change, the
safest option here is to just revert that commit. Should there be
desire to clean this up in the future, the change will need to be
tested with a more complete coverage of cards and host systems.

http://bugzilla.kernel.org/show_bug.cgi?id=13483

Cc: stable@kernel.org
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Hans Pontar reported success on the sourceforge zd1211-devs mailing list.
The device is branded "Arcor Easy Stick A 50 WLAN" (device manufactured
by SMC for a German ISP - SMC model name: WN4501H-LF-IR). General
information and Windows driver are available under (German only):

http://www.arcor.de/hilfe/neu/index.php?sid=&aktion=anzeigen&rubrik=004018140&id=487

Device details:

USB-IDs: Vendor: 0x083A Device: 0xE503
Chip ID: zd1211b chip 083a:e503 v4810 high 00-1d-19 AL2230S_RF pa0 g--N-
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Hans Pontar <pontar@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The patch adds a mutex to protect the iwm_reset_worker against netdev
ndo_open and ndo_stop because all of them call iwm_up and iwm_down in
the implementation. Note the latter two are already protected by
rtnl. So if iwm_reset_worker is not required in the future, the mutex
can also be removed.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>