Use helper function to figure out if a tunnel is using ipsec.
Also, avoid accessing ->sk_policy directly since it's RCU protected.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ilias Apalodimas says:

====================
netsec driver improvements

This patchset introduces some improvements on socionext netsec driver.
 - patch 1/2, avoids unneeded MMIO reads on the Rx path
 - patch 2/2, is adjusting the numbers of descriptors used

Changes since v1:
 - Move dma_rmb() to protect descriptor accesses until the device
 has updated the NETSEC_RX_PKT_OWN_FIELD bit
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Increasing descriptors to 256 from 128 and adjusting the NAPI weight
to 64 increases performace on Rx by ~20% on 64byte packets
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

MMIO reads for remaining packets in queue occur (at least)twice per
invocation of netsec_process_rx(). We can use the packet descriptor to
identify if it's owned by the hardware and break out, avoiding the more
expensive MMIO read operations. This has a ~2% increase on the pps of the
Rx path when tested with 64byte packets
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/neterion/vxge/vxge-config.c:1097:6: warning:
 variable 'ret' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/neterion/vxge/vxge-config.c:2263:6: warning:
 variable 'req_out' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/neterion/vxge/vxge-config.c:2262:22: warning:
 variable 'status' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/neterion/vxge/vxge-config.c:2360:22: warning:
 variable 'status' set but not used [-Wunused-but-set-variable]
  enum vxge_hw_status status = VXGE_HW_OK;
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Caleb Raitto says:

====================
virtio_net: Expand affinity to arbitrary numbers of cpu and vq

Virtio-net tries to pin each virtual queue rx and tx interrupt to a cpu if
there are as many queues as cpus.

Expand this heuristic to configure a reasonable affinity setting also
when the number of cpus != the number of virtual queues.

Patch 1 allows vqs to take an affinity mask with more than 1 cpu.
Patch 2 generalizes the algorithm in virtnet_set_affinity beyond
the case where #cpus == #vqs.

v2 changes:
Renamed "virtio_net: Make vp_set_vq_affinity() take a mask." to
"virtio: Make vp_set_vq_affinity() take a mask."

Tested:

[InstanceSetup]
set_multiqueue = false

$ cd /proc/irq
$ for i in `seq 24 60` ; do sudo grep ".*" $i/smp_affinity_list;  done
0-15
0
0
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
0-15
0-15
0-15
0-15

$ cd /sys/class/net/eth0/queues/
$ for i in `seq 0 15` ; do sudo grep ".*" tx-$i/xps_cpus; done
0001
0002
0004
0008
0010
0020
0040
0080
0100
0200
0400
0800
1000
2000
4000
8000

$ sudo ethtool -L eth0 combined 15

$ cd /proc/irq
$ for i in `seq 24 60` ; do sudo grep ".*" $i/smp_affinity_list;  done
0-15
0-1
0-1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
15
15
0-15
0-15
0-15
0-15

$ cd /sys/class/net/eth0/queues/
$ for i in `seq 0 14` ; do sudo grep ".*" tx-$i/xps_cpus; done
0003
0004
0008
0010
0020
0040
0080
0100
0200
0400
0800
1000
2000
4000
8000

$ sudo ethtool -L eth0 combined 8

$ cd /proc/irq
$ for i in `seq 24 60` ; do sudo grep ".*" $i/smp_affinity_list;  done
0-15
0-1
0-1
2-3
2-3
4-5
4-5
6-7
6-7
8-9
8-9
10-11
10-11
12-13
12-13
14-15
14-15
9
9
10
10
11
11
12
12
13
13
14
14
15
15
15
15
0-15
0-15
0-15
0-15

$ cd /sys/class/net/eth0/queues/
$ for i in `seq 0 7` ; do sudo grep ".*" tx-$i/xps_cpus; done
0003
000c
0030
00c0
0300
0c00
3000
c000

$ sudo ethtool -L eth0 combined 16
$ sudo sh -c "echo 0 > /sys/devices/system/cpu/cpu15/online"

$ cd /proc/irq
$ for i in `seq 24 60` ; do sudo grep ".*" $i/smp_affinity_list;  done
0-15
0
0
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
0
0
0-15
0-15
0-15
0-15

$ cd /sys/class/net/eth0/queues/
$ for i in `seq 0 15` ; do sudo grep ".*" tx-$i/xps_cpus; done
0001
0002
0004
0008
0010
0020
0040
0080
0100
0200
0400
0800
1000
2000
4000
0001

$ for i in `seq 8 15`; \
do sudo sh -c "echo 0 > /sys/devices/system/cpu/cpu$i/online"; done

$ cd /proc/irq
$ for i in `seq 24 60` ; do sudo grep ".*" $i/smp_affinity_list;  done
0-15
0
0
1
1
2
2
3
3
4
4
5
5
6
6
7
7
0
0
1
1
2
2
3
3
4
4
5
5
6
6
7
7
0-15
0-15
0-15
0-15

$ cd /sys/class/net/eth0/queues/
$ for i in `seq 0 15` ; do sudo grep ".*" tx-$i/xps_cpus; done
0001
0002
0004
0008
0010
0020
0040
0080
0001
0002
0004
0008
0010
0020
0040
0080
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Always set the affinity hint, even if #cpu != #vq.

Handle the case where #cpu > #vq (including when #cpu % #vq != 0) and
when #vq > #cpu (including when #vq % #cpu != 0).
Signed-off-by: Caleb Raitto <caraitto@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jon Olson <jonolson@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make vp_set_vq_affinity() take a cpumask instead of taking a single CPU.

If there are fewer queues than cores, queue affinity should be able to
map to multiple cores.

Link: https://patchwork.ozlabs.org/patch/948149/Suggested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Caleb Raitto <caraitto@google.com>
Acked-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PTP support includes:
    Ingress, and egress timestamping.
    One step timestamping available.
    PTP clock support.
    Periodic output support.
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuchung Cheng says:

====================
tcp: new mechanism to ACK immediately

This patch is a follow-up feature improvement to the recent fixes on
the performance issues in ECN (delayed) ACKs. Many of the fixes use
tcp_enter_quickack_mode routine to force immediate ACKs. However the
routine also reset tracking interactive session. This is not ideal
because these immediate ACKs are required by protocol specifics
unrelated to the interactiveness nature of the application.

This patch set introduces a new flag to send a one-time immediate ACK
without changing the status of interactive session tracking. With this
patch set the immediate ACKs are generated upon these protocol states:

1) When a hole is repaired
2) When CE status changes between subsequent data packets received
3) When a data packet carries CWR flag
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously commit 9aee4000 ("tcp: ack immediately when a cwr
packet arrives") calls tcp_enter_quickack_mode to force sending
two immediate ACKs upon receiving a packet w/ CWR flag. The side
effect is it'll also reset the delayed ACK timer and interactive
session tracking. This patch removes that side effect by using the
new ACK_NOW flag to force an immmediate ACK.

Packetdrill to demonstrate:

    0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
   +0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
   +0 setsockopt(3, SOL_TCP, TCP_CONGESTION, "dctcp", 5) = 0
   +0 bind(3, ..., ...) = 0
   +0 listen(3, 1) = 0

   +0 < [ect0] SEW 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
   +0 > SE. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 8>
  +.1 < [ect0] . 1:1(0) ack 1 win 257
   +0 accept(3, ..., ...) = 4

   +0 < [ect0] . 1:1001(1000) ack 1 win 257
   +0 > [ect01] . 1:1(0) ack 1001

   +0 write(4, ..., 1) = 1
   +0 > [ect01] P. 1:2(1) ack 1001

   +0 < [ect0] . 1001:2001(1000) ack 2 win 257
   +0 write(4, ..., 1) = 1
   +0 > [ect01] P. 2:3(1) ack 2001

   +0 < [ect0] . 2001:3001(1000) ack 3 win 257
   +0 < [ect0] . 3001:4001(1000) ack 3 win 257
   // Ack delayed ...

   +.01 < [ce] P. 4001:4501(500) ack 3 win 257
   +0 > [ect01] . 3:3(0) ack 4001
   +0 > [ect01] E. 3:3(0) ack 4501

+.001 read(4, ..., 4500) = 4500
   +0 write(4, ..., 1) = 1
   +0 > [ect01] PE. 3:4(1) ack 4501 win 100

 +.01 < [ect0] W. 4501:5501(1000) ack 4 win 257
   // No delayed ACK on CWR flag
   +0 > [ect01] . 4:4(0) ack 5501

 +.31 < [ect0] . 5501:6501(1000) ack 4 win 257
   +0 > [ect01] . 4:4(0) ack 6501

Fixes: 9aee4000 ("tcp: ack immediately when a cwr packet arrives")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC 5681 sec 4.2:
  To provide feedback to senders recovering from losses, the receiver
  SHOULD send an immediate ACK when it receives a data segment that
  fills in all or part of a gap in the sequence space.

When a gap is partially filled, __tcp_ack_snd_check already checks
the out-of-order queue and correctly send an immediate ACK. However
when a gap is fully filled, the previous implementation only resets
pingpong mode which does not guarantee an immediate ACK because the
quick ACK counter may be zero. This patch addresses this issue by
marking the one-time immediate ACK flag instead.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The recent fix of acking immediately in DCTCP on CE status change
has an undesirable side-effect: it also resets TCP ack timer and
disables pingpong mode (interactive session). But the CE status
change has nothing to do with them. This patch addresses that by
using the new one-time immediate ACK flag instead of calling
tcp_enter_quickack_mode().
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new flag to indicate a one-time immediate ACK. This flag is
occasionaly set under specific TCP protocol states in addition to
the more common quickack mechanism for interactive application.

In several cases in the TCP code we want to force an immediate ACK
but do not want to call tcp_enter_quickack_mode() because we do
not want to forget the icsk_ack.pingpong or icsk_ack.ato state.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Notice that in this particular case, I placed the "fall through"
annotation at the bottom of the case, which is what GCC is expecting
to find.

Addresses-Coverity-ID: 115075 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Notice that in this particular case, I placed the "fall through"
annotation at the bottom of the case, which is what GCC is expecting
to find.

Addresses-Coverity-ID: 1369529 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Notice that in this particular case, I replaced the code comment at the
top of the switch statement with a proper "fall through" annotation for
each case, which is what GCC is expecting to find.

Addresses-Coverity-ID: 1056542 ("Missing break in switch")
Addresses-Coverity-ID: 1339579 ("Missing break in switch")
Addresses-Coverity-ID: 1369526 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The static int 'zero' is defined but is never used hence it is
redundant and can be removed. The use of this variable was removed
with commit a158bdd3 ("rxrpc: Fix call timeouts").

Cleans up clang warning:
warning: 'zero' defined but not used [-Wunused-const-variable=]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtl8152_system_suspend defines the variable "ret", but it is not modified
after initialization. So just remove it.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes following smatch warnings:

drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2826 bnxt_fill_coredump_seg_hdr() error: strcpy() '"sEgM"' too large for 'seg_hdr->signature' (5 vs 4)
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2858 bnxt_fill_coredump_record() error: strcpy() '"cOrE"' too large for 'record->signature' (5 vs 4)
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2879 bnxt_fill_coredump_record() error: strcpy() 'utsname()->sysname' too large for 'record->os_name' (65 vs 32)

Fixes: 6c5657d0 ("bnxt_en: Add support for ethtool get dump.")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add LED identification support for liquidio TP copperhead cards.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes: 5e7baf0f ("qed/qede: Multi CoS support.")
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function mlxsw_core_driver_put only traverse mlxsw_core_driver_list
to find the matched mlxsw_driver,but never used it.
So it can be removed safely.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mvneta Ethernet driver is used on a few different Marvell SoCs.
Some SoCs have per cpu interrupts for Ethernet events, the driver uses
a per CPU napi structure for this case. Some SoCs such as armada 3700
have a single interrupt for Ethernet events, the driver uses a global
napi structure for this case.

Current mvneta_config_rss() always operates the per cpu napi structure.
Fix it by operating a global napi for "single interrupt" case, and per
cpu napi structure for remaining cases.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Fixes: 2636ac3c ("net: mvneta: Add network support for Armada 3700 SoC")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

With SMC-D z/OS sends a test link signal every 10 seconds. Linux is
supposed to answer, otherwise the SMC-D connection breaks.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: smaller improvements

This series includes smaller improvements, no functional change
intended.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We don't have to configure the max jumbo frame size per chip
(sub-)version. It can be easily determined based on the chip family.
And new members of the RTL8168 family (if there are any) should be
automatically covered.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We don't have to configure the csum function per chip (sub-)version.
The distinction is simple, versions RTL8102e and from RTL8168c onwards
support csum_v2.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify the interrupt handler a little and make it better readable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The asm headers shouldn't be included directly. asm/irq.h is
implicitly included by linux/interrupt.h, and instead of
asm/io.h include linux/io.h.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The version number hasn't changed for ages and in general I doubt it
provides any benefit. The message in rtl_init_one() may even be
misleading because it's printed also if something fails in probe.
Therefore let's remove the version information.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2018-08-10

Here's one more (most likely last) bluetooth-next pull request for the
4.19 kernel.

 - Added support for MediaTek serial Bluetooth devices
 - Initial skeleton for controller-side address resolution support
 - Fix BT_HCIUART_RTL related Kconfig dependencies
 - A few other minor fixes/cleanups

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter updates for net-next

The following batch contains netfilter updates for your net-next tree:

1) Expose NFT_OSF_MAXGENRELEN maximum OS name length from the new OS
   passive fingerprint matching extension, from Fernando Fernandez.

2) Add extension to support for fine grain conntrack timeout policies
   from nf_tables. As preparation works, this patchset moves
   nf_ct_untimeout() to nf_conntrack_timeout and it also decouples the
   timeout policy from the ctnl_timeout object, most work done by
   Harsha Sharma.

3) Enable connection tracking when conntrack helper is in place.

4) Missing enumeration in uapi header when splitting original xt_osf
   to nfnetlink_osf, also from Fernando.

5) Fix a sparse warning due to incorrect typing in the nf_osf_find(),
   from Wei Yongjun.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

display Data Center bridging information in debug
fs.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Array pci_speed is defined but is never used hence it is redundant
and can be removed.

Cleans up clang warning:
warning: 'pci_speed' defined but not used [-Wunused-const-variable=]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Arrays mlxsw_i2c_driver_name and mlxsw_pci_driver_name are defined
but never used hence they are redundant and can be removed.

Cleans up clang warnings:
warning: 'mlxsw_i2c_driver_name' defined but not used
warning: 'mlxsw_pci_driver_name' defined but not used
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Building virtio_net driver without CONFIG_XPS fails with:

    drivers/net/virtio_net.c: In function ‘virtnet_set_affinity’:
    drivers/net/virtio_net.c:1910:3: error: implicit declaration of function ‘__netif_set_xps_queue’ [-Werror=implicit-function-declaration]
       __netif_set_xps_queue(vi->dev, mask, i, false);
       ^
Fixes: 4d99f660 ("net: allow to call netif_reset_xps_queues() under cpus_read_lock")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the definitions for LE address resolution enable HCI commands.
When the LE address resolution enable gets changed via HCI commands
make sure that flag gets updated.
Signed-off-by: Ankit Navik <ankit.p.navik@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Change t4fw_version.h to update latest firmware version
number to 1.20.8.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The definition of static_key_slow_inc() has cpus_read_lock in place. In the
virtio_net driver, XPS queues are initialized after setting the queue:cpu
affinity in virtnet_set_affinity() which is already protected within
cpus_read_lock. Lockdep prints a warning when we are trying to acquire
cpus_read_lock when it is already held.

This patch adds an ability to call __netif_set_xps_queue under
cpus_read_lock().
Acked-by: Jason Wang <jasowang@redhat.com>

============================================
WARNING: possible recursive locking detected
4.18.0-rc3-next-20180703+ #1 Not tainted
--------------------------------------------
swapper/0/1 is trying to acquire lock:
00000000cf973d46 (cpu_hotplug_lock.rw_sem){++++}, at: static_key_slow_inc+0xe/0x20

but task is already holding lock:
00000000cf973d46 (cpu_hotplug_lock.rw_sem){++++}, at: init_vqs+0x513/0x5a0

other info that might help us debug this:
 Possible unsafe locking scenario:

       CPU0
       ----
  lock(cpu_hotplug_lock.rw_sem);
  lock(cpu_hotplug_lock.rw_sem);

 *** DEADLOCK ***

 May be due to missing lock nesting notation

3 locks held by swapper/0/1:
 #0: 00000000244bc7da (&dev->mutex){....}, at: __driver_attach+0x5a/0x110
 #1: 00000000cf973d46 (cpu_hotplug_lock.rw_sem){++++}, at: init_vqs+0x513/0x5a0
 #2: 000000005cd8463f (xps_map_mutex){+.+.}, at: __netif_set_xps_queue+0x8d/0xc60

v2: move cpus_read_lock() out of __netif_set_xps_queue()

Cc: "Nambiar, Amritha" <amritha.nambiar@intel.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Fixes: 8af2c06f ("net-sysfs: Add interface for Rx queue(s) map per Tx queue")
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>