An error occurred fetching the project authors.
- 24 Sep, 2011 26 commits
-
-
Chris Rankin authored
This patch closes the race on the device and extension lists at USB disconnect time. Previously, the device was removed from the device list during em28xx_release_resources(), and then passed to the em28xx_close_extension() function so that all extensions could run their fini() operations. However, this left a (brief, theoretical, highly unlikely ;-)) window between these two calls during which a new module could call em28xx_register_extension(). The result would have been that the em28xx_usb_disconnect() function would also have passed the device to the new extension's fini() function, despite never having called the extension's init() function. This patch also restores em28xx_close_extension()'s symmetry with em28xx_init_extension(), and establishes the property that every device in the device list must have been initialised for every extension in the extension list. Signed-off-by:
Chris Rankin <rankincj@yahoo.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Andy Walls authored
(Resending because Mauro reported losing some emails on IRC) Provide CX2388[578] IR receive timeout (RTO) reports in the final space raw event sent up the chain to the raw IR pulse decoders. This should allow the lirc decoder to actually measure the inter-transmission gap properly. Signed-off-by:
Andy Walls <awalls@md.metrocast.net> Signed-off-by:
-
Sylwester Nawrocki authored
There is no need to put the IRQ number in driver's private platform data structure as this can also be passed in struct i2c_lient.irq. Signed-off-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by:
-
Sylwester Nawrocki authored
Switch to generic media bus signal polarity flags and allow configuring the FIELD signal polarity. Signed-off-by:
-
Sylwester Nawrocki authored
FIELD signal is used for indicating frame field type to the frame grabber in interlaced scan mode, as specified in ITU-R BT.601 standard. In normal operation mode FIELD = 0 selects Field1 (odd) and FIELD = 1 selects Field2 (even). When the FIELD signal is inverted it's the other way around. Add corresponding flags for configuring the FIELD signal polarity, V4L2_MBUS_FIELD_EVEN_HIGH for the standard (non-inverted) case and V4L2_MBUS_FIELD_EVEN_LOW for inverted case. Also add a comment about usage of V4L2_MBUS_[HV]SYNC* flags for the hardware that uses [HV]REF signals. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Igor M. Liplianin authored
Signed-off-by:
Igor M. Liplianin <liplianin@me.by> Signed-off-by:
-
Pekka Enberg authored
This patch converts some ifdef'd wrapper functions from macros to static inline functions to kill the following warnings issued by GCC: CC [M] drivers/media/rc/ir-raw.o drivers/media/rc/ir-raw.c: In function ‘init_decoders’: drivers/media/rc/ir-raw.c:353:2: warning: statement with no effect [-Wunused-value] drivers/media/rc/ir-raw.c:354:2: warning: statement with no effect [-Wunused-value] drivers/media/rc/ir-raw.c:355:2: warning: statement with no effect [-Wunused-value] drivers/media/rc/ir-raw.c:356:2: warning: statement with no effect [-Wunused-value] drivers/media/rc/ir-raw.c:357:2: warning: statement with no effect [-Wunused-value] drivers/media/rc/ir-raw.c:359:2: warning: statement with no effect [-Wunused-value] Cc: Mauro Carvalho Chehab <mchehab@infradead.org> Cc: "David Härdeman" <david@hardeman.nu> Cc: Jarod Wilson <jarod@redhat.com> Cc: <linux-media@vger.kernel.org> Signed-off-by:Pekka Enberg <penberg@kernel.org> Signed-off-by:
-
Jean-François Moine authored
Signed-off-by:
Jean-François Moine <moinejf@free.fr> Signed-off-by:
-
Jean-François Moine authored
Signed-off-by:
-
Frank Schaefer authored
Tested with webcam "SilverCrest WC2130". Signed-off-by:
Frank Schaefer <fschaefer.oss@googlemail.com> Signed-off-by:
-
Wolfram Sang authored
Signed-off-by:
Wolfram Sang <w.sang@pengutronix.de> Signed-off-by:
-
Jean-François Moine authored
As the choice of the alternate setting has been enhanced in the gspca main, forcing its number here is no more useful. Signed-off-by:
-
Jean-François Moine authored
The JPEG quality was guessed as around 82%. Information in ms-win drivers says it should be 85%. Signed-off-by:
-
Jean-François Moine authored
Signed-off-by:
-
Jean-François Moine authored
Some webcams ask for a greater time to start. This patch increases the delay before timeout error on capture start. Signed-off-by:
-
Jean-François Moine authored
This driver is based on Anders Blomdell's source proposed in april 2009. It has been extended to handle the tp6810 bridge and the soi763a sensor. Signed-off-by:
-
Jean-François Moine authored
This patch is adapted from a patch from Sarah Sharp (2010/05/03). The xHCD handler checks the USB bandwidth on usb_set_interface() instead of on usb_submit_urb(). Now, the same treatment is applied in case of error of both functions. Signed-off-by:
-
Jean-François Moine authored
Previously image transfer used to use the highest altsetting, which, most of the time, took the whole USB bandwidth. Now, the altsetting is chosen according to an estimation of the bandwidth needed for image transfer. Signed-off-by:
-
Jean-François Moine authored
The sd_isoc_init() did only a set interface which is done in gspca main. Signed-off-by:
-
tvboxspy authored
Correct tuner settings for more accuracy. This now makes the tuner section more compatible with other versions of the IT913X series. TODOs Version 2 chip Signed-off-by:
Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by:
-
tvboxspy authored
Add remote support for KWORLD UB499-2T-T09 The remote supplied is the same as KWORLD_315U. Signed-off-by:
-
Arvydas Sidorenko authored
This is an improved version of the patch I sent a little ago. The problem was: On my DC-1125 webcam chip from Syntek, whenever the webcam turns on, the LED light on it is turned on also and never turns off again unless system is shut downed or restarted. The previous version seemed to break some other laptop webcam work. Thanks to Andrea Anacleto for the bug report and solution. Signed-off-by:
Andrea Anacleto <andreaanacleto@libero.it> Signed-off-by:
Arvydas Sidorenko <asido4@gmail.com> Signed-off-by:
-
Martin Hostettler authored
Ioctls on the subdevs node currently don't dispatch the register access debug driver callbacks. Add the dispatching with the same security checks are for non subdev video nodes (i.e. only capable(CAP_SYS_ADMIN may call the register access ioctls). Signed-off-by:
Martin Hostettler <martin@neutronstar.dyndns.org> Acked-by:
-
Manjunath Hadli authored
remove VPBE_DISPLAY_SD_BUF_SIZE as it is no longer used. Signed-off-by:
Manjunath Hadli <manjunath.hadli@ti.com> Signed-off-by:
-
Jose Alberto Reguero authored
Signed-off-by:
Jose Alberto Reguero <jareguero@telefonica.net> Signed-off-by:
-
Laurent Pinchart authored
The uvcvideo extension unit API requires constants defined in the video.h header. Add it to the list of includes exported to userspace. Signed-off-by:
-
- 23 Sep, 2011 10 commits
-
-
Stephan Lachowsky authored
Signed-off-by:
-
Al Cooper authored
The UVC driver uses usb_alloc_coherent() to allocate DMA data buffers. On systems without coherent DMA this ends up allocating buffers in uncached memory. The subsequent memcpy's done to coalesce the DMA chunks into contiguous buffers then run VERY slowly. On a MIPS test system the memcpy is about 200 times slower. This issue prevents the system from keeping up with 720p YUYV data at 10fps. The following patch uses kmalloc to alloc the DMA buffers instead of usb_alloc_coherent on systems without coherent DMA. With this patch the system was easily able to keep up with 720p at 10fps. Signed-off-by:
Al Cooper <alcooperx@gmail.com> Acked-by:
-
Laurent Pinchart authored
The UVCIOC_CTRL_ADD, UVCIOC_CTRL_MAP_OLD, UVCIOC_CTRL_GET and UVCIOC_CTRL_SET ioctls are deprecated and were scheduled for removal for v2.6.42. As v2.6.42 == v3.2, remove them. Signed-off-by:
-
Arne Caspari authored
The Imaging Source CCD cameras use a vendor specific interface class even though they are actually UVC compliant. Signed-off-by:
Arne Caspari <arne@unicap-imaging.org> Signed-off-by:
-
Mauro Carvalho Chehab authored
Prevents errors when merging with -next: drivers/media/rc/keymaps/rc-snapstream-firefly.c:105:16: error: expected declaration specifiers or ‘...’ before string constant drivers/media/rc/keymaps/rc-snapstream-firefly.c:106:15: error: expected declaration specifiers or ‘...’ before string constant Signed-off-by: -
Marek Szyprowski authored
This patch fixes build break caused by commit ba7fcb0c ("[media] media: vb2: dma contig allocator: use dma_addr instread of paddr"). Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Cc: Greg KH <greg@kroah.com> Signed-off-by:
-
Igor M. Liplianin authored
[mchehab@redhat.com: Fix a merge conflict] Signed-off-by:
Igor M. Liplianin <liplianin@netup.ru> Signed-off-by:
-
Igor M. Liplianin authored
Signed-off-by:
-
Mauro Carvalho Chehab authored
The serious bugs got fixed already. Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by:
-
- 22 Sep, 2011 4 commits
-
-
Anssi Hannula authored
The ati_remote driver supports more remotes nowadays, update the description to reflect that. Signed-off-by:
Anssi Hannula <anssi.hannula@iki.fi> Signed-off-by:
-
Anssi Hannula authored
The protocol differs by having two toggle bits in the scancode. Since one of the bits is otherwise unused, we can safely handle the bits unconditionally. [mchehab@redhat.com: Fix some bad whitespacing] Signed-off-by:
-
Anssi Hannula authored
Signed-off-by: -
Anssi Hannula authored
The ati_remote_dump() function tries to not print "Weird byte" warning for 1-byte responses that contain 0xff or 0x00, but it doesn't work properly as it simply falls back to the "Weird data" warning in the else clause. Fix that by adding an inner if clause. Signed-off-by:
-
