When bringing up new hardware, or otherwise experimenting, GPU hangs are
a way of life. However, the automatic GPU reset can do more harm than
good under these circumstances, as we may wish to capture a full trace for
debugging.

Based on a patch by Zhenyu Wang.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

On Ironlake, the LP0 latency is hardcoded and in ns unit, while on
Sandybridge, it comes from a register and with unit 0.1 us. So, fix
the wrong latency value while computing wm0 on Ironlake and Sandybridge.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

This patch actually makes the watermark code even uglier (if that's
possible), but has the advantage of sharing code between SNB and ILK at
least.  Longer term we should refactor the watermark stuff into its own
file and clean it up now that we know how it's supposed to work.

Supporting WM2 on my Vaio reduced power consumption by around 0.5W, so
this patch is definitely worthwhile (though it also needs lots of test
coverage).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: pass the watermark structs arounds]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

Flush the chipset write buffers before and after adjusting the GTT base
register, just in case. We only modify this value upon initialisation
(boot and resume) so there should be no outstanding writes, however
there are always those persistent PGTBL_ER that keep getting reported
upon resume.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

On i830 if the tail pointer is set to within 2 cachelines of the end of
the buffer, the chip may hang. So instead if the tail were to land in
that location, we pad the end of the buffer with NOPs, and start again
at the beginning.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

There should be no difference, but we can eliminate redundant code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

In some configuration, the PCU may allow us to overclock the GPU.
Check for this case and adjust the max frequency as appropriate.  Also
initialize the min/max frequencies to default values as indicated by
hardware.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

... and just any combination of bits & ~PFIT_ENABLE. This way we do not
attempt disable to the panel fitter controller uselessly upon
intel_lvds_disable().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

By tracking the current status of the backlight we can prevent recording
the value of the current backlight when we have disabled it. And so
prevent restoring it to 'off' after an unbalanced sequence of
intel_lvds_disable/enable.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=22672Tested-by: Alex Riesen <raa.lkml@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

Alex Fiestas reported an issue with his HDMI connector being misdetected
as DVI unless he had something connected upon boot. By moving the
decision as to whether to use HDMI or DVI encoding for the HDMI capable
output until we probe the monitor means that we should avoid sending a
HDMI signal to a DVI monitor and also correctly detect hardware like
Alex's.

However, to really determine what connector is soldered onto the wire we
need to inspect the VBT sdvo child devices - but can we trust it?
Reported-by: Alex Fiestas <alex@eyeos.org>
Tested-by: Alex Fiestas <alex@eyeos.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32828Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

Some voltage swing/pre-emphasis level use the same value on eDP
Sandybridge, like 400mv_0db and 600mv_0db are with the same value
of (0x0 << 22). So, fix them, and point out the value if it isn't
a supported voltage swing/pre-emphasis level.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

Since Linux 2.6.36 the digital output on my system (855GME + DVI-I) is
not working any longer. The analog output is always activated
regardless of the type of monitor attached.

The culprit seems to be intel_crt_detect_ddc(), which returns true as
soon as an ACK from the EDID device is received. Obviously this
approach does not work with DVI-I where the analog and digital outputs
share a common DDC bus.

In a similar manner to the shared DDC wire, ala the "Mac Mini Hack", we
need an additional check to make sure that there really is an analog
device attached to the DDC.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

When trying to do channel equalization, we need to make sure we still
have clock recovery on all lanes while training.  We also need to try
clock recovery again if we lose the clock or if channel eq fails 5
times.  We'll try clock recovery up to 5 more times before giving up
entirely.

Gets suspend/resume working on my Vaio again and brings us back into
compliance with the DP training sequence spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

We were using a stale pointer in the check which caused us to use CPU
attached DP params when we should have been using PCH attached params.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31988Tested-by: Jan-Hendrik Zab <jan@jhz.name>
Tested-by: Christoph Lukas <christoph.lukas@gmx.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (390 commits)
  drm/radeon/kms: disable underscan by default
  drm/radeon/kms: only enable hdmi features if the monitor supports audio
  drm: Restore the old_fb upon modeset failure
  drm/nouveau: fix hwmon device binding
  radeon: consolidate asic-specific function decls for pre-r600
  vga_switcheroo: comparing too few characters in strncmp()
  drm/radeon/kms: add NI pci ids
  drm/radeon/kms: don't enable pcie gen2 on NI yet
  drm/radeon/kms: add radeon_asic struct for NI asics
  drm/radeon/kms/ni: load default sclk/mclk/vddc at pm init
  drm/radeon/kms: add ucode loader for NI
  drm/radeon/kms: add support for DCE5 display LUTs
  drm/radeon/kms: add ni_reg.h
  drm/radeon/kms: add bo blit support for NI
  drm/radeon/kms: always use writeback/events for fences on NI
  drm/radeon/kms: adjust default clock/vddc tracking for pm on DCE5
  drm/radeon/kms: add backend map workaround for barts
  drm/radeon/kms: fill gpu init for NI asics
  drm/radeon/kms: add disabled vbios accessor for NI asics
  drm/radeon/kms: handle NI thermal controller
  ...

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c: Constify i2c_client where possible
  i2c-algo-bit: Complain about masters which can't read SCL
  i2c-algo-bit: Refactor adapter registration
  i2c: Add generic I2C multiplexer using GPIO API
  i2c-nforce2: Remove unnecessary cast of pci_get_drvdata
  i2c-i801: Include <linux/slab.h>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (52 commits)
  Blackfin: encode cpu-rev into uImage name
  Blackfin: bf54x: don't ack GPIO ints when unmasking them
  Blackfin: sram_free_with_lsl: do not ignore return value of sram_free
  Blackfin: boards: add missing "static" to peripheral lists
  Blackfin: DNP5370: new board port
  Blackfin: bf518f-ezbrd: fix dsa resources
  Blackfin: move "-m elf32bfin" to general LDFLAGS
  Blackfin: kgdb_test: make sure to initialize num2
  Blackfin: kgdb: disable preempt schedule when running single step in kgdb
  Blackfin: kgdb: disable interrupt when single stepping in ADEOS
  Blackfin: SMP: kgdb: apply anomaly 257 work around
  Blackfin: fix building IPIPE code when XIP is enabled
  Blackfin: SMP: kgdb: flush core internal write buffer before flushinv
  Blackfin: sport_uart resources: remove unused secondary RX/TX pins
  Blackfin: tll6527m: fix spelling in unused code (struct name)
  Blackfin: bf527-ezkit: add adau1373 chip address
  Blackfin: no-mpu: fix masking of small uncached dma region
  Blackfin: pm: drop irq save/restore in standby and suspend to mem callback
  MAINTAINERS: update Analog Devices support info
  Blackfin: dpmc.h: pull in new pll.h
  ...

Merge branch 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6

* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  driver core: Document that device_rename() is only for networking
  sysfs: remove useless test from sysfs_merge_group
  driver-core: merge private parts of class and bus
  driver core: fix whitespace in class_attr_string

* 'staging-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (510 commits)
  staging: speakup: fix failure handling
  staging: usbip: remove double giveback of URB
  Staging: batman-adv: Remove batman-adv from staging
  Staging: hv: Use only one txf buffer per channel and kmalloc/GFP_KERNEL on initialize
  staging: hv: remove unneeded osd_schedule_callback
  staging: hv: convert channel_mgmt.c to not call osd_schedule_callback
  staging: hv: convert vmbus_on_msg_dpc to not call osd_schedule_callback
  staging: brcm80211: Fix WL_<type> logging macros
  Staging: IIO: DDS: AD9833 / AD9834 driver
  Staging: IIO: dds.h convenience macros
  Staging: IIO: Direct digital synthesis abi documentation
  staging: brcm80211: Convert ETHER_TYPE_802_1X to ETH_P_PAE
  staging: brcm80211: Remove unused ETHER_TYPE_<foo> #defines
  staging: brcm80211: Remove ETHER_HDR_LEN, use ETH_HLEN
  staging: brcm80211: Convert ETHER_ADDR_LEN to ETH_ALEN
  staging: brcm80211: Convert ETHER_IS<FOO> to is_<foo>_ether_addr
  staging: brcm80211: Remove unused ether_<foo> #defines and struct
  staging: brcm80211: Convert ETHER_IS_MULTI to is_multicast_ether_addr
  staging: brcm80211: Remove unused #defines ETHER_<foo>_LOCALADDR
  Staging: comedi: Fix checkpatch.pl issues in file s526.c
  ...

Fix up trivial conflict in drivers/video/udlfb.c

Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86: (36 commits)
  sony-laptop: support new hotkeys on the P, Z and EC series
  platform/x86: Consistently select LEDS Kconfig options
  sony-laptop: fix sparse non-ANSI function warning
  intel_ips: fix sparse non-ANSI function warning
  Support KHLB2 in the compal laptop driver
  acer-wmi: Enabled Acer Launch Manager mode
  [PATCH] intel_pmic_gpio: modify EOI handling following change of kernel irq subsystem
  ACPI Thinkpad: We must always call va_end() after va_start() but do not do so in thinkpad_acpi.c::acpi_evalf()
  acer-wmi: Initialize wlan/bluetooth/wwan rfkill software block state
  acer-wmi: Detect the WiFi/Bluetooth/3G devices available
  acer-wmi: Add 3G rfkill sysfs file
  acer-wmi: Add acer wmi hotkey events support
  platform/x86: Kconfig: Replace select by depends on ACPI_WMI
  ideapad: pass ideapad_priv as argument (part 2)
  ideapad: pass ideapad_priv as argument (part 1)
  ideapad: add markups, unify comments and return result when init
  ideapad: add hotkey support
  ideapad: let camera power control entry under platform driver
  ideapad: add platform driver for ideapad
  fujitsu-laptop: fix compiler warning on pnp_ids
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68knommu: Need to check __get_user()/__put_user() result
  m68knommu: signal.c __user annotations
  m68knommu: Equivalent of "m68k: handle new gcc's"
  m68knommu: f_pcr has been gone since headers' merge
  m68knommu: Don't lose state if sigframe setup fails
  m68knommu: Handle multiple pending signals
  m68knommu: Switch to saner sigsuspend
  m68knommu: Don't bother with SA_ONESHOT
  m68k: Check __get_user()/__put_user() return value
  m68k: Missing syscall_trace() on sigreturn
  m68k: Fix stack mangling logics in sigreturn
  m68k: If we fail to set sigframe up, just leave regs alone...
  m68k: Don't lose state if sigframe setup fails
  m68k: Simplify the singlestepping handling in signals
  m68k: Switch to saner sigsuspend()
  m68k: Resetting sa_handler in local copy of k_sigaction is pointless
  m68k/sun3: Kill pte_unmap() warnings

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] Avoid array overflow if there are too many cpus in SRAT table
  [IA64] Remove unlikely from cpu_is_offline
  [IA64] irq_ia64, use set_irq_chip
  [IA64] perfmon: Change vmalloc to vzalloc and drop memset.
  [IA64] eliminate race condition in smp_flush_tlb_mm

Merge branch 'for-torvalds' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson

* 'for-torvalds' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
  ux500: allow 5500 and 8500 to be built together
  ux500: modem_irq is only for 5500
  ux500: dynamic SOC detection
  ux500: rename MOP board Kconfig
  ux500: remove build-time changing macros

* 'msm-smp' of git://codeaurora.org/quic/kernel/davidb/linux-msm:
  msm: add SMP support for msm
  msm: hotplug: support cpu hotplug on msm
  msm: timer: SMP timer support for msm
  msm: scm-boot: Support for setting cold/warm boot addresses
  msm: Secure Channel Manager (SCM) support

Helper functions for I2C and SMBus transactions don't modify the
i2c_client that is passed to them, so it can be marked const.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

The I2C specification explicitly describes both SDA and SCL as
bidirectional lines. An I2C master with a read-only SCL is thus not
compliant. If a slow slave stretches the clock, errors will happen,
so the bus can't be considered as reliable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Use a function pointer to decide whether to call i2c_add_adapter or
i2c_add_numbered_adapter. This makes the code more compact than the
current strategy of having the common code in a separate function.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Add an i2c mux driver providing access to i2c bus segments using a
hardware MUX sitting on a master bus and controlled through gpio pins.

E.G. something like:

  ----------              ----------  Bus segment 1   - - - - -
 |          | SCL/SDA    |          |-------------- |           |
 |          |------------|          |
 |          |            |          | Bus segment 2 |           |
 |  Linux   | GPIO 1..N  |   MUX    |---------------   Devices
 |          |------------|          |               |           |
 |          |            |          | Bus segment M
 |          |            |          |---------------|           |
  ----------              ----------                  - - - - -

SCL/SDA of the master I2C bus is multiplexed to bus segment 1..M
according to the settings of the GPIO pins 1..N.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Commit 5a0e3ad6 added direct inclusion
of <linux/slab.h> to those source files that appeared to need it, but
somehow missed this.  On most architectures <linux/slab.h> is still
indirectly included, but there are exceptions such as alpha.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

fix the failure handling in kobjects and the main function so that we
release the virtual keyboard if we exit due to another failure.
Signed-off-by: William Hubbs <w.d.hubbs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

In the vhci_urb_dequeue() function the TCP connection is checked twice.
Each time when the TCP connection is closed the URB is unlinked and given
back. Remove the second attempt of unlinking and giving back of the URB completely.

This patch fixes the bug described at https://bugzilla.kernel.org/show_bug.cgi?id=24872 .
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (30 commits)
  MAINTAINERS: Add tomoyo-dev-en ML.
  SELinux: define permissions for DCB netlink messages
  encrypted-keys: style and other cleanup
  encrypted-keys: verify datablob size before converting to binary
  trusted-keys: kzalloc and other cleanup
  trusted-keys: additional TSS return code and other error handling
  syslog: check cap_syslog when dmesg_restrict
  Smack: Transmute labels on specified directories
  selinux: cache sidtab_context_to_sid results
  SELinux: do not compute transition labels on mountpoint labeled filesystems
  This patch adds a new security attribute to Smack called SMACK64EXEC. It defines label that is used while task is running.
  SELinux: merge policydb_index_classes and policydb_index_others
  selinux: convert part of the sym_val_to_name array to use flex_array
  selinux: convert type_val_to_struct to flex_array
  flex_array: fix flex_array_put_ptr macro to be valid C
  SELinux: do not set automatic i_ino in selinuxfs
  selinux: rework security_netlbl_secattr_to_sid
  SELinux: standardize return code handling in selinuxfs.c
  SELinux: standardize return code handling in selinuxfs.c
  SELinux: standardize return code handling in policydb.c
  ...

Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>

Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
[Modified to hit the right file]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>

Dynamically detect the DBx500 SOC an revision based on the ASIC ID.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>

Rename the MOP board Kconfig entries to the same name as the machine
type, so that the machine_is_*() macros work correctly.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
[Updated to match changes in the tree]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>

To allow the possiblity of building U8500 and U5500 support in the same
image.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
[Rebased to latest changes in Russells tree]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>

Add new mappings for assist, VAIO, zoom and eject buttons present on
refurbished P, Z and EC models.
Reported-by: Gyorgy Jeney <nog.lkml@gmail.com>
Reported-by: Stephan Mueller <smueller@chronox.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: (44 commits)
  hwmon: Support for Dallas Semiconductor DS620
  hwmon: driver for Sensirion SHT21 humidity and temperature sensor
  hwmon: Add humidity attribute to sysfs ABI
  hwmon: sysfs ABI updates
  hwmon: (via-cputemp) sync hotplug handling with coretemp/pkgtemp
  hwmon: (lm95241) Rewrite to avoid using macros
  hwmon: (applesmc) Fix checkpatch errors and fix value range checks
  hwmon: (applesmc) Update copyright information
  hwmon: (applesmc) Silence driver
  hwmon: (applesmc) Simplify feature sysfs handling
  hwmon: (applesmc) Dynamic creation of fan files
  hwmon: (applesmc) Extract all features generically
  hwmon: (applesmc) Handle new temperature format
  hwmon: (applesmc) Dynamic creation of temperature files
  hwmon: (applesmc) Introduce a register lookup table
  hwmon: (applesmc) Use pr_fmt and pr_<level>
  hwmon: (applesmc) Relax the severity of device init failure
  hwmon: (applesmc) Add MacBookAir3,1(3,2) support
  hwmon: (w83627hf) Use pr_fmt and pr_<level>
  hwmon: (w83627ehf) Use pr_fmt and pr_<level>
  ...