- 22 Mar, 2017 23 commits
-
-
Or Gerlitz authored
Refactor the code to deal with add/del TC rules to have handler per NIC/E-switch offloading use case, and push the latter into the e-switch code. This provides better separation and is to be used in down-stream patch for applying a fix. Fixes: bffaa916 ("net/mlx5: E-Switch, Add control for inline mode") Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by:
Roi Dayan <roid@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Or Gerlitz authored
The switch cases for the rate limit set and query commands were missing, which could get us wrong under fw error or driver reset flow, fix that. Fixes: 1466cc5b ('net/mlx5: Rate limit tables support') Signed-off-by:
Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by:
-
David S. Miller authored
Merge tag 'wireless-drivers-for-davem-2017-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo says: ==================== wireless-drivers fixes for 4.11 iwlwifi * fix a user reported warning in DQA mwifiex * fix a potential double free * fix lost early debug logs * fix init wakeup warning message from device framework * add Ganapathi and Xinming as maintainers ath10k * fix regression with QCA6174 during resume and firmware crash ==================== Signed-off-by:
-
Ying Xue authored
Until now, tipc_nametbl_unsubscribe() is called at subscriptions reference count cleanup. Usually the subscriptions cleanup is called at subscription timeout or at subscription cancel or at subscriber delete. We have ignored the possibility of this being called from other locations, which causes deadlock as we try to grab the tn->nametbl_lock while holding it already. CPU1: CPU2: ---------- ---------------- tipc_nametbl_publish spin_lock_bh(&tn->nametbl_lock) tipc_nametbl_insert_publ tipc_nameseq_insert_publ tipc_subscrp_report_overlap tipc_subscrp_get tipc_subscrp_send_event tipc_close_conn tipc_subscrb_release_cb tipc_subscrb_delete tipc_subscrp_put tipc_subscrp_put tipc_subscrp_kref_release tipc_nametbl_unsubscribe spin_lock_bh(&tn->nametbl_lock) <<grab nametbl_lock again>> CPU1: CPU2: ---------- ---------------- tipc_nametbl_stop spin_lock_bh(&tn->nametbl_lock) tipc_purge_publications tipc_nameseq_remove_publ tipc_subscrp_report_overlap tipc_subscrp_get tipc_subscrp_send_event tipc_close_conn tipc_subscrb_release_cb tipc_subscrb_delete tipc_subscrp_put tipc_subscrp_put tipc_subscrp_kref_release tipc_nametbl_unsubscribe spin_lock_bh(&tn->nametbl_lock) <<grab nametbl_lock again>> In this commit, we advance the calling of tipc_nametbl_unsubscribe() from the refcount cleanup to the intended callers. Fixes: d094c4d5 ("tipc: add subscription refcount to avoid invalid delete") Reported-by:John Thompson <thompa.atl@gmail.com> Acked-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Signed-off-by:
-
Xin Long authored
This patch is to remove the unnecessary temporary variable 'err' from sctp_association_init. Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Xin Long authored
sctp_stream_free uses struct sctp_stream as a param, but struct sctp_stream is defined after it's declaration. This patch is to declare struct sctp_stream before sctp_stream_free. Fixes: a8386317 ("sctp: prepare asoc stream for stream reconf") Signed-off-by:
-
Arnd Bergmann authored
With posix timers having become optional, we get a build error with the cpts time sync option of the CPSW driver: drivers/net/ethernet/ti/cpts.c: In function 'cpts_find_ts': drivers/net/ethernet/ti/cpts.c:291:23: error: implicit declaration of function 'ptp_classify_raw';did you mean 'ptp_classifier_init'? [-Werror=implicit-function-declaration] This adds a hard dependency on PTP_CLOCK to avoid the problem, as building it without PTP support makes no sense anyway. Fixes: baa73d9e ("posix-timers: Make them configurable") Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: stable@vger.kernel.org Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Nicolas Pitre <nico@linaro.org> Signed-off-by:
-
Arnd Bergmann authored
The dependency is reversed: cpsw and netcp call into cpts, but cpts depends on the other two in Kconfig. This can lead to cpts being a loadable module and its callers built-in: drivers/net/ethernet/ti/cpsw.o: In function `cpsw_remove': cpsw.c:(.text.cpsw_remove+0xd0): undefined reference to `cpts_release' drivers/net/ethernet/ti/cpsw.o: In function `cpsw_rx_handler': cpsw.c:(.text.cpsw_rx_handler+0x2dc): undefined reference to `cpts_rx_timestamp' drivers/net/ethernet/ti/cpsw.o: In function `cpsw_tx_handler': cpsw.c:(.text.cpsw_tx_handler+0x7c): undefined reference to `cpts_tx_timestamp' drivers/net/ethernet/ti/cpsw.o: In function `cpsw_ndo_stop': As a workaround, I'm introducing another Kconfig symbol to control the compilation of cpts, while making the actual module controlled by a silent symbol that is =y when necessary. Fixes: 6246168b ("net: ethernet: ti: netcp: add support of cpts") Signed-off-by:
Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by:
-
David S. Miller authored
Hayes Wang says: ==================== r8152: fix the rx settings of RTL8153 The RMS and the rx early size should base on the same rx size. However, the RMS is set to 9K bytes now and the rx early depends on mtu. For using the rx buffer effectively, sync the two settings according to the mtu. ==================== Signed-off-by: -
hayeswang authored
revert commit a59e6d81 ("r8152: correct the rx early size") and fix the rx early size as (rx buffer size - rx packet size - rx desc size - alignment) / 4 Signed-off-by:
Hayes Wang <hayeswang@realtek.com> Signed-off-by:
-
hayeswang authored
Set the received maximum size (RMS) according to the mtu size. It is unnecessary to receive a packet which is more than the size we could transmit. Besides, this could let the rx buffer be used effectively. Signed-off-by:
-
Tejun Heo authored
The net_cls controller controls the classid field of each socket which is associated with the cgroup. Because the classid is per-socket attribute, when a task migrates to another cgroup or the configured classid of the cgroup changes, the controller needs to walk all sockets and update the classid value, which was implemented by 3b13758f ("cgroups: Allow dynamically changing net_classid"). While the approach is not scalable, migrating tasks which have a lot of fds attached to them is rare and the cost is born by the ones initiating the operations. However, for simplicity, both the migration and classid config change paths call update_classid() which scans all fds of all tasks in the target css. This is an overkill for the migration path which only needs to cover a much smaller subset of tasks which are actually getting migrated in. On cgroup v1, this can lead to unexpected scalability issues when one tries to migrate a task or process into a net_cls cgroup which already contains a lot of fds. Even if the migration traget doesn't have many to get scanned, update_classid() ends up scanning all fds in the target cgroup which can be extremely numerous. Unfortunately, on cgroup v2 which doesn't use net_cls, the problem is even worse. Before bfc2cf6f ("cgroup: call subsys->*attach() only for subsystems which are actually affected by migration"), cgroup core would call the ->css_attach callback even for controllers which don't see actual migration to a different css. As net_cls is always disabled but still mounted on cgroup v2, whenever a process is migrated on the cgroup v2 hierarchy, net_cls sees identity migration from root to root and cgroup core used to call ->css_attach callback for those. The net_cls ->css_attach ends up calling update_classid() on the root net_cls css to which all processes on the system belong to as the controller isn't used. This makes any cgroup v2 migration O(total_number_of_fds_on_the_system) which is horrible and easily leads to noticeable stalls triggering RCU stall warnings and so on. The worst symptom is already fixed in upstream by bfc2cf6f ("cgroup: call subsys->*attach() only for subsystems which are actually affected by migration"); however, backporting that commit is too invasive and we want to avoid other cases too. This patch updates net_cls's cgrp_attach() to iterate fds of only the processes which are actually getting migrated. This removes the surprising migration cost which is dependent on the total number of fds in the target cgroup. As this leaves write_classid() the only user of update_classid(), open-code the helper into write_classid(). Reported-by:
David Goode <dgoode@fb.com> Fixes: 3b13758f ("cgroups: Allow dynamically changing net_classid") Cc: stable@vger.kernel.org # v4.4+ Cc: Nina Schiff <ninasc@fb.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Tony Lindgren authored
This gets qmicli working with the MDM6600 modem. Cc: Bjørn Mork <bjorn@mork.no> Reviewed-by:
Sebastian Reichel <sre@kernel.org> Tested-by:
Tony Lindgren <tony@atomide.com> Acked-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Zi Shen Lim authored
Merge of 'linux-kselftest-4.11-rc1': 1. Partially removed use of 'test_objs' target, breaking force rebuild of BPFOBJ, introduced in commit d498f871 ("bpf: Rebuild bpf.o for any dependency update"). Update target so dependency on BPFOBJ is restored. 2. Introduced commit 2047f1d8 ("selftests: Fix the .c linking rule") which fixes order of LDLIBS. Commit d02d8986 ("bpf: Always test unprivileged programs") added libcap dependency into CFLAGS. Use LDLIBS instead to fix linking of test_verifier. 3. Introduced commit d83c3ba0 ("selftests: Fix selftests build to just build, not run tests"). Reordering the Makefile allows us to remove the 'all' target. Tested both: selftests/bpf$ make and selftests$ make TARGETS=bpf on Ubuntu 16.04.2. Signed-off-by:
Zi Shen Lim <zlim.lnx@gmail.com> Acked-by:
Daniel Borkmann <daniel@iogearbox.net> Tested-by:
Alexei Starovoitov <ast@kernel.org> Tested-by:
Shuah Khan <shuahkh@osg.samsung.com> Signed-off-by:
-
Soheil Hassas Yeganeh authored
SOF_TIMESTAMPING_OPT_STATS can be enabled and disabled while packets are collected on the error queue. So, checking SOF_TIMESTAMPING_OPT_STATS in sk->sk_tsflags is not enough to safely assume that the skb contains OPT_STATS data. Add a bit in sock_exterr_skb to indicate whether the skb contains opt_stats data. Fixes: 1c885808 ("tcp: SOF_TIMESTAMPING_OPT_STATS option for SO_TIMESTAMPING") Reported-by:
JongHwan Kim <zzoru007@gmail.com> Signed-off-by:
Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Soheil Hassas Yeganeh authored
__sock_recv_timestamp can be called for both normal skbs (for receive timestamps) and for skbs on the error queue (for transmit timestamps). Commit 1c885808 (tcp: SOF_TIMESTAMPING_OPT_STATS option for SO_TIMESTAMPING) assumes any skb passed to __sock_recv_timestamp are from the error queue, containing OPT_STATS in the content of the skb. This results in accessing invalid memory or generating junk data. To fix this, set skb->pkt_type to PACKET_OUTGOING for packets on the error queue. This is safe because on the receive path on local sockets skb->pkt_type is never set to PACKET_OUTGOING. With that, copy OPT_STATS from a packet, only if its pkt_type is PACKET_OUTGOING. Fixes: 1c885808 ("tcp: SOF_TIMESTAMPING_OPT_STATS option for SO_TIMESTAMPING") Reported-by:
-
Xin Long authored
This patch is to fix the issue that sctp_prsctp_prune_sent forgot to update q->out_qlen when removing a chunk from unsent queue. Fixes: 8dbdf1f5 ("sctp: implement prsctp PRIO policy") Signed-off-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
-
Xin Long authored
As tp->dst_pending_confirm's value can only be set 0 or 1, this patch is to change to define it as a bit instead of __u32. Signed-off-by:
-
Xin Long authored
Commit c86a773c ("sctp: add dst_pending_confirm flag") introduced a temporary variable "confirm" in sctp_packet_transmit. But it broke the rule that longer lines should be above shorter ones. Besides, this variable is not necessary, so this patch is to just remove it and use tp->dst_pending_confirm directly. Fixes: c86a773c ("sctp: add dst_pending_confirm flag") Signed-off-by:
-
David Ahern authored
The VRF driver takes a reference to the inet6_dev on the VRF device for its rt6_local dst when handling local traffic through the VRF device as a loopback. When the device is deleted the driver does a put on the idev but does not reset rt6i_idev in the rt6_info struct. When the dst is destroyed, dst_destroy calls ip6_dst_destroy which does a second put for what is essentially the same reference causing it to be prematurely freed. Reset rt6i_idev after the put in the vrf driver. Fixes: b4869aa2 ("net: vrf: ipv6 support for local traffic to local addresses") Signed-off-by:
David Ahern <dsa@cumulusnetworks.com> Signed-off-by:
-
Dan Carpenter authored
We could allocate less memory than intended because we do: bnad->regdata = kzalloc(len << 2, GFP_KERNEL); The shift can overflow leading to a crash. This is debugfs code so the impact is very small. Fixes: 7afc5dbd ("bna: Add debugfs interface.") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Rasesh Mody <rasesh.mody@cavium.com> Signed-off-by:
-
Bjørn Mork authored
This is a Dell branded Sierra Wireless EM7455. It is operating in MBIM mode by default, but can be configured to provide two QMI/RMNET functions. Signed-off-by:
-
Eric Dumazet authored
skb_cow(skb, sizeof(ip header)) is not very helpful in this context. First we need to use pskb_may_pull() to make sure the ip header is in skb linear part, then use skb_try_make_writable() to address clones issues. Fixes: 4c30719f ("[PKT_SCHED] dsmark: handle cloned and non-linear skb's") Signed-off-by:
-
- 21 Mar, 2017 9 commits
-
-
Yaroslav Isakov authored
Added missing logic in tun driver, which prevents apps to set offloads using tun ioctl, if offloads were previously disabled via ethtool Signed-off-by:
Yaroslav Isakov <yaroslav.isakov@gmail.com> Signed-off-by:
-
Andrey Ulanov authored
Dmitry has reported that a BUG_ON() condition in unix_notinflight() may be triggered by a simple code that forwards unix socket in an SCM_RIGHTS message. That is caused by incorrect unix socket GC implementation in unix_gc(). The GC first collects list of candidates, then (a) decrements their "children's" inflight counter, (b) checks which inflight counters are now 0, and then (c) increments all inflight counters back. (a) and (c) are done by calling scan_children() with inc_inflight or dec_inflight as the second argument. Commit 6209344f ("net: unix: fix inflight counting bug in garbage collector") changed scan_children() such that it no longer considers sockets that do not have UNIX_GC_CANDIDATE flag. It also added a block of code that that unsets this flag _before_ invoking scan_children(, dec_iflight, ). This may lead to incorrect inflight counters for some sockets. This change fixes this bug by changing order of operations: UNIX_GC_CANDIDATE is now unset only after all inflight counters are restored to the original state. kernel BUG at net/unix/garbage.c:149! RIP: 0010:[<ffffffff8717ebf4>] [<ffffffff8717ebf4>] unix_notinflight+0x3b4/0x490 net/unix/garbage.c:149 Call Trace: [<ffffffff8716cfbf>] unix_detach_fds.isra.19+0xff/0x170 net/unix/af_unix.c:1487 [<ffffffff8716f6a9>] unix_destruct_scm+0xf9/0x210 net/unix/af_unix.c:1496 [<ffffffff86a90a01>] skb_release_head_state+0x101/0x200 net/core/skbuff.c:655 [<ffffffff86a9808a>] skb_release_all+0x1a/0x60 net/core/skbuff.c:668 [<ffffffff86a980ea>] __kfree_skb+0x1a/0x30 net/core/skbuff.c:684 [<ffffffff86a98284>] kfree_skb+0x184/0x570 net/core/skbuff.c:705 [<ffffffff871789d5>] unix_release_sock+0x5b5/0xbd0 net/unix/af_unix.c:559 [<ffffffff87179039>] unix_release+0x49/0x90 net/unix/af_unix.c:836 [<ffffffff86a694b2>] sock_release+0x92/0x1f0 net/socket.c:570 [<ffffffff86a6962b>] sock_close+0x1b/0x20 net/socket.c:1017 [<ffffffff81a76b8e>] __fput+0x34e/0x910 fs/file_table.c:208 [<ffffffff81a771da>] ____fput+0x1a/0x20 fs/file_table.c:244 [<ffffffff81483ab0>] task_work_run+0x1a0/0x280 kernel/task_work.c:116 [< inline >] exit_task_work include/linux/task_work.h:21 [<ffffffff8141287a>] do_exit+0x183a/0x2640 kernel/exit.c:828 [<ffffffff8141383e>] do_group_exit+0x14e/0x420 kernel/exit.c:931 [<ffffffff814429d3>] get_signal+0x663/0x1880 kernel/signal.c:2307 [<ffffffff81239b45>] do_signal+0xc5/0x2190 arch/x86/kernel/signal.c:807 [<ffffffff8100666a>] exit_to_usermode_loop+0x1ea/0x2d0 arch/x86/entry/common.c:156 [< inline >] prepare_exit_to_usermode arch/x86/entry/common.c:190 [<ffffffff81009693>] syscall_return_slowpath+0x4d3/0x570 arch/x86/entry/common.c:259 [<ffffffff881478e6>] entry_SYSCALL_64_fastpath+0xc4/0xc6 Link: https://lkml.org/lkml/2017/3/6/252Signed-off-by:
Andrey Ulanov <andreyu@google.com> Reported-by:
Dmitry Vyukov <dvyukov@google.com> Fixes: 6209344f ("net: unix: fix inflight counting bug in garbage collector") Signed-off-by:
-
David S. Miller authored
Peng Tao says: ==================== vsock: cancel connect packets when failing to connect Currently, if a connect call fails on a signal or timeout (e.g., guest is still in the process of starting up), we'll just return to caller and leave the connect packet queued and they are sent even though the connection is considered a failure, which can confuse applications with unwanted false connect attempt. The patchset enables vsock (both host and guest) to cancel queued packets when a connect attempt is considered to fail. v5 changelog: - change virtio_vsock_pkt->cancel_token back to virtio_vsock_pkt->vsk v4 changelog: - drop two unnecessary void * cast - update new callback comment v3 changelog: - define cancel_pkt callback in struct vsock_transport rather than struct virtio_transport - rename virtio_vsock_pkt->vsk to virtio_vsock_pkt->cancel_token v2 changelog: - fix queued_replies counting and resume tx/rx when necessary ==================== Signed-off-by: -
Peng Tao authored
Otherwise we'll leave the packets queued until releasing vsock device. E.g., if guest is slow to start up, resulting ETIMEDOUT on connect, guest will get the connect requests from failed host sockets. Reviewed-by:
Stefan Hajnoczi <stefanha@redhat.com> Reviewed-by:
Jorgen Hansen <jhansen@vmware.com> Signed-off-by:
Peng Tao <bergwolf@gmail.com> Signed-off-by:
-
Peng Tao authored
Reviewed-by:
-
Peng Tao authored
To allow canceling all packets of a connection. Reviewed-by:
-
Peng Tao authored
So that we can cancel a queued pkt later if necessary. Signed-off-by:
-
Herbert Xu authored
On Tue, Mar 14, 2017 at 10:44:10AM +0100, Dmitry Vyukov wrote: > > Yes, please. > Disregarding some reports is not a good way long term. Please try this patch. ---8<--- Subject: netlink: Annotate nlk cb_mutex by protocol Currently all occurences of nlk->cb_mutex are annotated by lockdep as a single class. This causes a false lcokdep cycle involving genl and crypto_user. This patch fixes it by dividing cb_mutex into individual classes based on the netlink protocol. As genl and crypto_user do not use the same netlink protocol this breaks the false dependency loop. Reported-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
hayeswang authored
The list rx_done would be initialized when the linking on occurs. Therefore, if a napi is scheduled without any linking on before, the following kernel panic would happen. BUG: unable to handle kernel NULL pointer dereference at 000000000000008 IP: [<ffffffffc085efde>] r8152_poll+0xe1e/0x1210 [r8152] PGD 0 Oops: 0002 [#1] SMP Signed-off-by:
-
- 20 Mar, 2017 1 commit
-
-
Ryan Hsu authored
In the 'commit ebee76f7 ("ath10k: allow setting coverage class")', it inherits the design and the address offset from ath9k, but the address is not applicable to QCA6174, which leads to a random crash while doing the resume() operation, since the set_coverage_class.ops will be called from ieee80211_reconfig() when resume() (if the wow is not configured). Fix the incorrect address offset here to avoid the random crash. Verified on QCA6174/hw3.0 with firmware WLAN.RM.4.4-00022-QCARMSWPZ-2. kvalo: this also seems to fix a regression with firmware restart. Fixes: ebee76f7 ("ath10k: allow setting coverage class") Cc: <stable@vger.kernel.org> # v4.10 Signed-off-by:
Ryan Hsu <ryanhsu@qca.qualcomm.com> Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com>
-
- 17 Mar, 2017 7 commits
-
-
Eric Dumazet authored
Commit b369e7fd ("tcp: make TCP_INFO more consistent") moved lock_sock_fast() earlier in tcp_get_info() This has the minor effect that jiffies value being sampled at the beginning of tcp_get_info() is more likely to be off by one, and we report big tcpi_last_data_sent values (like 0xFFFFFFFF). Since we lock the socket, fetching tcp_time_stamp right before doing the jiffies_to_msecs() calls is enough to remove these wrong values. Signed-off-by:
-
stephen hemminger authored
When device is being setup on boot, there is a small race where network device callback is registered, but the netvsc_device pointer is not set yet. This can cause a NULL ptr dereference if packet arrives during this window. Fixes: 46b4f7f5 ("netvsc: eliminate per-device outstanding send counter") Signed-off-by:
Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by:
-
WANG Cong authored
Andrei reported a false alarm of lockdep at net/bridge/br_fdb.c:109, this is because in Andrei's case, a spin_bug() was already triggered before this, therefore the debug_locks is turned off, lockdep_is_held() is no longer accurate after that. We should use lockdep_assert_held_once() instead of lockdep_is_held() to respect debug_locks. Fixes: 410b3d48 ("bridge: fdb: add proper lock checks in searching functions") Reported-by:
Andrei Vagin <avagin@gmail.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Acked-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:
-
David Howells authored
If we receive a BUSY packet for a call we think we've just completed, the packet is handed off to the connection processor to deal with - but the connection processor doesn't expect a BUSY packet and so flags a protocol error. Fix this by simply ignoring the BUSY packet for the moment. The symptom of this may appear as a system call failing with EPROTO. This may be triggered by pressing ctrl-C under some circumstances. This comes about we abort calls due to interruption by a signal (which we shouldn't do, but that's going to be a large fix and mostly in fs/afs/). What happens is that we abort the call and may also abort follow up calls too (this needs offloading somehoe). So we see a transmission of something like the following sequence of packets: DATA for call N ABORT call N DATA for call N+1 ABORT call N+1 in very quick succession on the same channel. However, the peer may have deferred the processing of the ABORT from the call N to a background thread and thus sees the DATA message from the call N+1 coming in before it has cleared the channel. Thus it sends a BUSY packet[*]. [*] Note that some implementations (OpenAFS, for example) mark the BUSY packet with one plus the callNumber of the call prior to call N. Ordinarily, this would be call N, but there's no requirement for the calls on a channel to be numbered strictly sequentially (the number is required to increase). This is wrong and means that the callNumber in the BUSY packet should be ignored (it really ought to be N+1 since that's what it's in response to). Signed-off-by:David Howells <dhowells@redhat.com> Signed-off-by:
-
Nathan Fontenot authored
The pointer array for the tx/rx sub crqs should be free'ed when releasing the tx/rx sub crqs. Signed-off-by:
Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by:
-
David Ahern authored
Anycast routes have the RTF_ANYCAST flag set, but when dumping routes for userspace the route type is not set to RTN_ANYCAST. Make it so. Fixes: 58c4fb86 ("[IPV6]: Flag RTF_ANYCAST for anycast routes") CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Signed-off-by:
-
David Ahern authored
Alive tracking of nexthops can account for a link twice if the carrier goes down followed by an admin down of the same link rendering multipath routes useless. This is similar to 79099aab for UNREGISTER events and DOWN events. Fix by tracking number of alive nexthops in mpls_ifdown similar to the logic in mpls_ifup. Checking the flags per nexthop once after all events have been processed is simpler than trying to maintian a running count through all event combinations. Also, WRITE_ONCE is used instead of ACCESS_ONCE to set rt_nhn_alive per a comment from checkpatch: WARNING: Prefer WRITE_ONCE(<FOO>, <BAR>) over ACCESS_ONCE(<FOO>) = <BAR> Fixes: c89359a4 ("mpls: support for dead routes") Signed-off-by:
Robert Shearman <rshearma@brocade.com> Signed-off-by:
-
