This makes sure hci_cmd_sync_queue only queue new work if HCI_RUNNING
has been set otherwise there is a risk of commands being sent while
turning off.

Because hci_cmd_sync_queue can no longer queue work while HCI_RUNNING is
not set it cannot be used to power on adapters so instead
hci_cmd_sync_submit is introduced which bypass the HCI_RUNNING check, so
it behaves like the old implementation.

Link: https://lore.kernel.org/all/CAB4PzUpDMvdc8j2MdeSAy1KkAE-D3woprCwAdYWeOc-3v3c9Sw@mail.gmail.com/Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

WCN6855 will report memdump via ACL data or HCI event when
it get crashed, so we collect memdump to debug firmware.
Signed-off-by: Tim Jiang <quic_tjiang@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This enables flow control before checking for bootloader signature and
deciding whether FW download is needed or not. In case of V1 bootloader
chips w8987 and w8997, it is observed that if WLAN FW is downloaded first
and power save is enabled in wlan core, bootloader signatures are not
emitted by the BT core when the chip is put to sleep. As a result, the
driver skips FW download and subsequent HCI commands get timeout errors
in dmesg as shown below:

[  112.898867] Bluetooth: hci0: Opcode 0x c03 failed: -110
[  114.914865] Bluetooth: hci0: Setting baudrate failed (-110)
[  116.930856] Bluetooth: hci0: Setting wake-up method failed (-110)

By enabling the flow control, the host enables its RTS pin, and an
interrupt in chip's UART peripheral causes the bootloader to wake up,
enabling the bootloader signatures, which then helps in downloading
the bluetooth FW file.

This changes all instances of 0/1 for serdev_device_set_flow_control()
to false/true.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Some of the sync commands might take a long time to complete, e.g.
LE Create Connection when the peer device isn't responding might take
20 seconds before it times out. If suspend command is issued during
this time, it will need to wait for completion since both commands are
using the same sync lock.

This patch cancel any running sync commands before attempting to
suspend or adapter power off.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add the support for RTL8851B BT controller on USB interface.
The necessary firmware will be submitted to linux-firmware project.

Note that the Bluetooth devices WITH the VID=0x0bda would be set the
feature quirk in btrtl_setup_realtek(). It's able to ignore the
feature flag set for the specific VID and PID in blacklist_table[] of
btusb.c. (check [1])

If Realtek Bluetooth chips WITHOUT the VID=0x0bda, it shall be added
the feature flag for the specific VID and PID in blacklist_table[] of
btusb.c. (check [2])

[1] '9ab9235f ("Bluetooth: btrtl: Enable WBS for the specific
    Realtek devices")'
[2] '73280f13 ("Bluetooth: btusb: Add the more support IDs for
    Realtek RTL8822CE")'

The device info from /sys/kernel/debug/usb/devices as below.

T:  Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 33 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0bda ProdID=b851 Rev= 0.00
S:  Manufacturer=Realtek
S:  Product=802.11ax WLAN Adapter
S:  SerialNumber=00E04C885A01
C:* #Ifs= 3 Cfg#= 1 Atr=80 MxPwr=500mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 8 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This fixes the following sparse warnings:

   drivers/bluetooth/btnxpuart.c:681:23: sparse: sparse:
   restricted __le16 degrades to integer
   drivers/bluetooth/btnxpuart.c:690:82: sparse:
   sparse: incorrect type in argument 2 (different base types)
   @@     expected unsigned short [usertype] req_len
   @@     got restricted __le16 [usertype] len @@
   drivers/bluetooth/btnxpuart.c:690:82: sparse:
   expected unsigned short [usertype] req_len
   drivers/bluetooth/btnxpuart.c:690:82: sparse:
   got restricted __le16 [usertype] len
   drivers/bluetooth/btnxpuart.c:694:84: sparse:
   sparse: incorrect type in argument 2 (different base types)
   @@     expected unsigned short [usertype] req_len
   @@     got restricted __le16 [usertype] len @@
   drivers/bluetooth/btnxpuart.c:694:84: sparse:
   expected unsigned short [usertype] req_len
   drivers/bluetooth/btnxpuart.c:694:84: sparse:
   got restricted __le16 [usertype] len
   drivers/bluetooth/btnxpuart.c:708:23: sparse:
   sparse: incorrect type in assignment (different base types)
   @@     expected unsigned int [usertype] requested_len
   @@     got restricted __le16 [usertype] len @@
   drivers/bluetooth/btnxpuart.c:708:23: sparse:
   expected unsigned int [usertype] requested_len
   drivers/bluetooth/btnxpuart.c:708:23: sparse:
   got restricted __le16 [usertype] len
   drivers/bluetooth/btnxpuart.c:787:78: sparse:
   sparse: incorrect type in argument 2 (different base types)
   @@     expected unsigned short [usertype] chipid
   @@     got restricted __le16 [usertype] chip_id @@
   drivers/bluetooth/btnxpuart.c:787:78: sparse:
   expected unsigned short [usertype] chipid
   drivers/bluetooth/btnxpuart.c:787:78: sparse:
   got restricted __le16 [usertype] chip_id
   drivers/bluetooth/btnxpuart.c:810:74: sparse:
   sparse: incorrect type in argument 2 (different base types)
   @@     expected unsigned short [usertype] req_len
   @@     got restricted __le16 [usertype] len @@
   drivers/bluetooth/btnxpuart.c:810:74: sparse:
   expected unsigned short [usertype] req_len
   drivers/bluetooth/btnxpuart.c:810:74: sparse:
   got restricted __le16 [usertype] len
   drivers/bluetooth/btnxpuart.c:815:76: sparse:
   sparse: incorrect type in argument 2 (different base types)
   @@     expected unsigned short [usertype] req_len
   @@     got restricted __le16 [usertype] len @@
   drivers/bluetooth/btnxpuart.c:815:76: sparse:
   expected unsigned short [usertype] req_len
   drivers/bluetooth/btnxpuart.c:815:76: sparse:
   got restricted __le16 [usertype] len
   drivers/bluetooth/btnxpuart.c:834:16: sparse:
   sparse: restricted __le32 degrades to integer
   drivers/bluetooth/btnxpuart.c:843:55: sparse:
   sparse: restricted __le32 degrades to integer
   drivers/bluetooth/btnxpuart.c:844:36: sparse:
   sparse: incorrect type in argument 3 (different base types)
   @@     expected unsigned long [usertype]
   @@     got restricted __le16 [usertype] len @@
   drivers/bluetooth/btnxpuart.c:844:36: sparse:
   expected unsigned long [usertype]
   drivers/bluetooth/btnxpuart.c:844:36: sparse:
   got restricted __le16 [usertype] len
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202304160736.Tsa0zTBU-lkp@intel.com/Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Realtek changed the format of the firmware file as v2. The driver
should implement the patch to extract the firmware data from the
firmware file. The future chips must apply this patch for firmware loading.
This patch is compatible with the both previous format and v2 as well.
Signed-off-by: Allen Chen <allen_chen@realsil.com.cn>
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Tested-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

API hci_devcd_init() stores its u32 type parameter @dump_size into
skb, but it does not specify which byte order is used to store the
integer, let us take little endian to store and parse the integer.

Fixes: f5cc609d09d4 ("Bluetooth: Add support for hci devcoredump")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Previously, capability was checked using capable(), which verified that the
caller of the ioctl system call had the required capability. In addition,
the result of the check would be stored in the HCI_SOCK_TRUSTED flag,
making it persistent for the socket.

However, malicious programs can abuse this approach by deliberately sharing
an HCI socket with a privileged task. The HCI socket will be marked as
trusted when the privileged task occasionally makes an ioctl call.

This problem can be solved by using sk_capable() to check capability, which
ensures that not only the current task but also the socket opener has the
specified capability, thus reducing the risk of privilege escalation
through the previously identified vulnerability.

Cc: stable@vger.kernel.org
Fixes: f81f5b2d ("Bluetooth: Send control open and close messages for HCI raw sockets")
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

conn->chan_lock isn't acquired before l2cap_get_chan_by_scid,
if l2cap_get_chan_by_scid returns NULL, then 'bad unlock balance'
is triggered.

Reported-by: syzbot+9519d6b5b79cf7787cf3@syzkaller.appspotmail.com
Link: https://lore.kernel.org/all/000000000000894f5f05f95e9f4d@google.com/Signed-off-by: Min Li <lm0963hack@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Previously, channel open messages were always sent to monitors on the first
ioctl() call for unbound HCI sockets, even if the command and arguments
were completely invalid. This can leave an exploitable hole with the abuse
of invalid ioctl calls.

This commit hardens the ioctl processing logic by first checking if the
command is valid, and immediately returning with an ENOIOCTLCMD error code
if it is not. This ensures that ioctl calls with invalid commands are free
of side effects, and increases the difficulty of further exploitation by
forcing exploitation to find a way to pass a valid command first.
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Co-developed-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This reverts commit 1e9ac114.

This patch introduces a possible null-ptr-def problem. Revert it. And the
fixed bug by this patch have resolved by commit 73f7b171 ("Bluetooth:
btsdio: fix use after free bug in btsdio_remove due to race condition").

Fixes: 1e9ac114 ("Bluetooth: btsdio: fix use after free bug in btsdio_remove due to unfinished work")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The ATS2851 based controller advertises support for command "LE Set Random
Private Address Timeout" but does not actually implement it, impeding the
controller initialization.

Add the quirk HCI_QUIRK_BROKEN_SET_RPA_TIMEOUT to unblock the controller
initialization.

< HCI Command: LE Set Resolvable Private... (0x08|0x002e) plen 2
        Timeout: 900 seconds
> HCI Event: Command Status (0x0f) plen 4
      LE Set Resolvable Private Address Timeout (0x08|0x002e) ncmd 1
        Status: Unknown HCI Command (0x01)
Co-developed-by: imoc <wzj9912@gmail.com>
Signed-off-by: imoc <wzj9912@gmail.com>
Signed-off-by: Raul Cheleguini <raul.cheleguini@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

When submitting HCI_OP_LE_CREATE_CIS the code shall wait for
HCI_EVT_LE_CIS_ESTABLISHED thus enforcing the serialization of
HCI_OP_LE_CREATE_CIS as the Core spec does not allow to send them in
parallel:

  BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 4, Part E page 2566:

  If the Host issues this command before all the HCI_LE_CIS_Established
  events from the previous use of the command have been generated, the
  Controller shall return the error code Command Disallowed (0x0C).
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This fixes only matching CIS by address which prevents creating new hcon
if upper layer is requesting a specific CIS ID.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Since it is required for some configurations to have multiple CIS with
the same peer which is now covered by iso-tester in the following test
cases:

    ISO AC 6(i) - Success
    ISO AC 7(i) - Success
    ISO AC 8(i) - Success
    ISO AC 9(i) - Success
    ISO AC 11(i) - Success
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

There are a number of bugs here:

1) If "count" is less than sizeof(dump_data.data) then it copies
   uninitialized data.
2) If simple_write_to_buffer() returns -EFAULT then we run into a
   problem "ret < count" comparison.  "count" is an unsigned long so the
   comparison is type promoted to unsigned long and the negative returns
   become high positive values.  That also results in copying
   uninitialized data.
3) If "*ppos" is non-zero then the first part of the dump_data
   buffer is uninitialized.  Using copy_from_user() instead of
   simple_write_to_buffer() is more appropriate here.

Fixes: d5d5df6da0aa ("Bluetooth: Add vhci devcoredump support")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The driver can be compile tested with !CONFIG_OF making certain data
unused.
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Remove extra line setting the broadcast code parameter of the
hci_cp_le_create_big struct to 0. The broadcast code is copied
from the QoS struct.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Fixed a wrong indentation before "return".This line uses a 7 space
indent instead of a tab.
Signed-off-by: Lanzhe Li <u202212060@hust.edu.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

We can never assume the uart will deliver a complete packet to the BT
layer at once, the expected packet may be divided into several parts by
uart as uart doesn't know the received packet size, the received data
count may mismatch with the expected packet size, so here
is_valid_bootloader_signature() check may always return false.

Even we remove the count check in is_valid_bootloader_signature(), then
the first part of the data which includes the packet type can pass the
is_valid_bootloader_signature() check, but the remaining parts don't
have the packet type data still cannot pass the check, here return
directly will cause the data loss.

So need to remove the received bootloader signature check here, the
h4_recv_buf() can help us combine the different data received into one
packet. If any out-of-sync or incomplete bootloader signature is received,
it is safe to ignore and discard it, and process the next bootloader
signature.
Co-developed-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This sets the default power save mode setting to disabled.
With this setting, this driver will behave like a normal h4 driver.
If user needs to use the power save feature, it can be enabled
using the following vendor command:
hcitool cmd 3f 23 02 00 00 (HCI_NXP_AUTO_SLEEP_MODE)
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This adds a call to ps_wakeup() before closing the serdev device, to
de-assert UART break.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This adds support to download helper FW file for the legacy NXP chipset
88w8997 for the btnxpuart driver. This helper FW file is necessary to
set the bootloader baudrate to 3000000 after which the actual BT FW file
can be downloaded. This change helps bring the FW download time from
around 10 sec to less than 2 sec for 88w8997 chip. For newer chipsets,
both V1 and V3 bootloader, driver sends the cmd5 and cmd7 to the chip
bootloader, and does not need a helper FW file.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The DSDT for the Acer Iconia One 7 B1-750 models (which share
the same mainboard) specifies a IOAPIC IRQ for the HCI -> host IRQ but
this is not correct.

Like the Asus TF103C these tablets use pin 17 of the INT33FC:02 GPIO
controller for the IRQ and this pin is _not_ configured in direct IRQ
mode by the firmware.

Add a DMI match for this, re-using the Asus TF103C gpiod_lookup_table,
to fix bluetooth not working on these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The DSDT for the Lenovo Yoga Tablet 2 830 / 1050 models (which share
the same mainboard) specifies a IOAPIC IRQ for the HCI -> host IRQ but
this is not correct.

Like the Asus TF103C these tablets use pin 17 of the INT33FC:02 GPIO
controller for the IRQ and this pin is _not_ configured in direct IRQ
mode by the firmware.

Add a DMI match for this, re-using the Asus TF103C gpiod_lookup_table,
to fix bluetooth not working on these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The bcm43430a0 and bcm43430a1 BT does not support the 0xfc45 command
to set the UART clock to 48 MHz and it also does not work at 4000000
baud without this command as some newer models do.

These chips are found on ACPI/x86 devices where the operating baudrate
does not come from the firmware but is hardcoded at 4000000, which does
not work.

Add a max_baudrate value to struct bcm_device_data and set this
to 2000000 on all known ACPI hardware-ids for the bcm43430a0
and the bcm43430a1.

Note this also adds the BCM2E9F ACPI HID which was missing until now.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

On some devices the BCM Bluetooth adapter does not have a valid bdaddr set.

btbcm.c currently sets HCI_QUIRK_INVALID_BDADDR to indicate when this is
the case. But this requires users to manual setup a btaddr, by doing e.g.:

btmgmt -i hci0 public-addr 'B0:F1:EC:82:1D:B3'

Which means that Bluetooth will not work out of the box on such devices.
To avoid this (where possible) hci_bcm sets: HCI_QUIRK_USE_BDADDR_PROPERTY
which tries to get the bdaddr from devicetree.

But this only works on devicetree platforms. On UEFI based platforms
there is a special Broadcom UEFI variable which when present contains
the devices bdaddr, just like how there is another UEFI variable which
contains wifi nvram contents including the wifi MAC address.

Add support for getting the bdaddr from this Broadcom UEFI variable,
so that Bluetooth will work OOTB for users on devices where this
UEFI variable is present.

This fixes Bluetooth not working on for example Asus T100HA 2-in-1s.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

As shown in the schematic diagram below.There may be a critical
scenario in the current code. If the device does not receive an
pure ack sent by the host due to insufficient receive buffer or
other reasons and triggers a retransmission, the host will always
be in an 'out-of-order' state.The state machine will get stuck.

       host                 device
     SEQ3,ACK4 --------->
               <--------- SEQ4,ACK4
     pure ACK  ---------> (not received)
(out-of-order) <--------- SEQ4,ACK4(retransmission)
                ........
(out-of-order) <--------- SEQ4,ACK4(retransmission)

According to the description in the core specification: "whenever
a reliable packet is received, an acknowledgment shall be generated."
So set H5_TX_ACK_REQ bit to trigger retransmission of pure ack packet
when "out-of-order" occurs.
Signed-off-by: Qiqi Zhang <eddy.zhang@rock-chips.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This enables 2M and Coded PHY by default if they are marked as supported
in the LE features bits.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Split bt_iso_qos into dedicated unicast and broadcast
structures and add additional broadcast parameters.

Fixes: eca0ae4a ("Bluetooth: Add initial implementation of BIS connections")
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Intercept debug exception events from the controller and put them into
a devcoredump using hci devcoredump APIs. The debug exception contains
data in a TLV format and it will be parsed in userspace.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Chethan Tumkur Narayan <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This patch implements the btusb driver side .coredump() callback to
trigger a devcoredump via sysfs.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add devcoredump support for vhci that creates forcce_devcoredump debugfs
entry. This is used for mgmt-tester tests.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add devcoredump APIs to hci core so that drivers only have to provide
the dump skbs instead of managing the synchronization and timeouts.

The devcoredump APIs should be used in the following manner:
 - hci_devcoredump_init is called to allocate the dump.
 - hci_devcoredump_append is called to append any skbs with dump data
   OR hci_devcoredump_append_pattern is called to insert a pattern.
 - hci_devcoredump_complete is called when all dump packets have been
   sent OR hci_devcoredump_abort is called to indicate an error and
   cancel an ongoing dump collection.

The high level APIs just prepare some skbs with the appropriate data and
queue it for the dump to process. Packets part of the crashdump can be
intercepted in the driver in interrupt context and forwarded directly to
the devcoredump APIs.

Internally, there are 5 states for the dump: idle, active, complete,
abort and timeout. A devcoredump will only be in active state after it
has been initialized. Once active, it accepts data to be appended,
patterns to be inserted (i.e. memset) and a completion event or an abort
event to generate a devcoredump. The timeout is initialized at the same
time the dump is initialized (defaulting to 10s) and will be cleared
either when the timeout occurs or the dump is complete or aborted.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Basically all Intel controllers support both Central/Peripheral
LE states.

This patch enables the LE States quirk by default on all
Solar and Magnertor Intel controllers.
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add regulators, GPIOs and changes required to power on/off wcn6855.
Add support for firmware download for wcn6855 which is in the
linux-firmware repository as hpbtfw21.tlv and hpnv21.bin.

Based on the assumption that this is similar to the wcn6750

Tested-on: BTFW.HSP.2.1.0-00538-VER_PATCHZ-1
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Tested-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add bindings for the QTI WCN6855 chipset.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The btrtl_set_quirks() has accessed btrtl_dev->ic_info->lmp_subver since
b8e482d02513. However, if installing a Realtek Bluetooth controller
without the driver supported, it will hit the NULL point accessed.

Add a check for NULL to avoid the Kernel Oops.
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This device is part of a Realtek RTW8852BE chip. The device table is as follows:

T:  Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3571 Rev= 0.00
S:  Manufacturer=Realtek
S:  Product=Bluetooth Radio
S:  SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>