Add routines for accessing the registers and counters in the performance
monitoring unit.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Many of the registers in the performance monitoring unit are write-only.
We need to save a "shadow" copy when we write to those registers so we
can retrieve the values if we need them later.

The new cbe_pmd_shadow_regs structure is added to the cbe_regs_map structure
so we have the appropriate per-node copies of these shadow values.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

There are a few definitions that are required by subsequent patches,
so add them here.

The original patch is from David Erb, but is significantly cleaned
up by Kevon Corry.

Cc: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

When in isolated mode, SPEs have access to an area of persistent
storage, which is per-SPE. In order for isolated-mode apps to
communicate arbitrary data through this storage, we need to ensure that
isolated physical SPEs can be reused for subsequent applications.

Add a file ("recycle") in a spethread dir to enable isolated-mode
recycling. By writing to this file, the kernel will reload the
isolated-mode loader kernel, allowing a new app to be run on the same
physical SPE.

This requires the spu_acquire_exclusive function to enforce exclusive
access to the SPE while the loader is initialised.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This patch adds general support for isolated mode SPE apps.

Isolated apps are started indirectly, by a dedicated loader "kernel".
This patch starts the loader when spe_create is invoked with the
ISOLATE flag. We do this at spe_create time to allow libspe to pass the
isolated app in before calling spe_run.

The loader is read from the device tree, at the location
"/spu-isolation/loader". If the loader is not present, an attempt to
start an isolated SPE binary will fail with -ENODEV.

Update: loader needs to be correctly aligned - copy to a kmalloced buf.
Update: remove workaround for systemsim/spurom 'L-bit' bug, which has
        been fixed.
Update: don't write to runcntl on spu_run_init: SPU is already running.
Update: do spu_setup_isolated earlier

Tested on systemsim.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This adds two new flags to spu_create:

SPU_CREATE_NONSCHED: create a context that is never moved
away from an SPE once it has started running. This flag
can only be used by tasks with the CAP_SYS_NICE capability.

SPU_CREATE_ISOLATED: create a nonschedulable context that
enters isolation mode upon first run. This requires the
SPU_CREATE_NONSCHED flag.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Remove the mostly unused variable isrc from struct spu and a forgotten
function declaration.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

SPRN_SDR1 and the SPE's MFC SDR are hypervisor resources and
are not accessible from a logical partition.  This change adds an
access wrapper.

When running on bare H/W, the spufs needs to only set the SPE's MFC SDR
to the value of the PPE's SPRN_SDR1 once at SPE initialization, so this
change renames mfc_sdr_set() to mfc_sdr_setup() and moves the
access of SPRN_SDR1 into the mmio wrapper.  It also removes the now
unneeded member mfc_sdr_RW from struct spu_priv1_collapsed.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>

--
Signed-off-by: Paul Mackerras <paulus@samba.org>

It makes for a friendlier API if irq_dispose_mapping(NO_IRQ) is a
nop, rather than triggering a WARN_ON.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Fixed some missing files to be deleted when running make clean
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Remove the iSeries initrd logic, instead just store the initrd location and
size in the device tree so generic code can do the rest for us.

The iSeries code had a "feature" which the generic code lacks, ie. if the
compressed initrd is bigger than the configured ram disk size, we make
the ram disk size bigger. That's bogus, as the compressed size of the initrd
tells us nothing about how big the ram disk needs to be. If the ram disk
isn't big enough you just need to make CONFIG_BLK_DEV_RAM_SIZE larger.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The original problem that inspired this patch was solved quite some time
ago (Turning off PCI didn't work), but this patch neatens things up a
little (I think), by putting all the PCI stuff inside a single CONFIG_PCI
block.  It also removes the OF PCI bus matching entries if CONFIG_PCI is
off.
Signed-off-by: Paul Mackerras <paulus@samba.org>

This patch adds the mktree program that is needed to post process zImage
wrappers for various PowerPC 4xx boards
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Provide primitive malloc, free, and realloc functions for bootwrapper.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Add serial console support for non-OF systems.  There is a generic serial
console layer which calls a serial console driver.  Included is the serial
console driver for the ns16550 class of uarts.  Necessary support routines
are added as well.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Add the latest version of the flatdevtree code and corresponding glue.

A phandle table now tracks values returned by ft_find_device().
The value returned by ft_find_device() is a phandle which is really
an index into the phandle table.  The phandle table contains the address
of the corresponding node.  When the flat dt is edited/moved, the node
pointers in the phandle table are updated accordingly so no phandles kept
by the caller become stale.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

More reorganization of the bootwrapper:
- Add dtb section to zImage
- ft_init now called by platform_init
- Pack a flat dt before calling kernel
- Remove size parameter from free
- printf only calls console_ops.write it its not NULL
- Some cleanup
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The lazy IRQ disable patch missed a couple of places where the
interrupt enable flags need to be restored correctly.  First, we
weren't restoring the paca->hard_enabled flag on interrupt exit.
Instead of saving it on entry, we compute it from the MSR_EE bit
in the MSR we are restoring at exit.  Secondly, the MMU hash miss
code was clearing both paca->soft_enabled and paca->hard_enabled
but not restoring them in the case where hash_page was able to
resolve the miss from the Linux page tables.
Signed-off-by: Paul Mackerras <paulus@samba.org>

Change the powerpc hpte_insert routines now called through ppc_md to
static scope.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Apparently we've copied the todc drivers, for various RTCs used in
embedded machines from ARCH=ppc to ARCH=powerpc, despite the fact that
it's never used in the latter.  This patch removes it.

If we ever need these drivers (which we probably shouldn't now the RTC
class stuff is in), we can transfer them one by one from ARCH=ppc,
removing from the hideous abomination which is the todc
"infrastructure".
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Without this patch, on an idle system I get:

cpu-power-0:21.638
cpu-power-1:27.102
cpu-power-2:29.343
cpu-power-3:25.784
Total: 103.8W

With this patch:

cpu-power-0:11.730
cpu-power-1:17.185
cpu-power-2:18.547
cpu-power-3:17.528
Total: 65.0W

If I lower HZ to 100, I can get it as low as:

cpu-power-0:10.938
cpu-power-1:16.021
cpu-power-2:17.245
cpu-power-3:16.145
Total: 60.2W

Another (older) Quad G5 went from 54W to 39W at HZ=250.

Coming back out of Deep Nap takes 40-70 cycles longer than coming back
from just Nap (which already takes quite a while). I don't think it'll
be a performance issue (interrupt latency on an idle system), but in
case someone does measurements feel free to report them.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This implements a lazy strategy for disabling interrupts.  This means
that local_irq_disable() et al. just clear the 'interrupts are
enabled' flag in the paca.  If an interrupt comes along, the interrupt
entry code notices that interrupts are supposed to be disabled, and
clears the EE bit in SRR1, clears the 'interrupts are hard-enabled'
flag in the paca, and returns.  This means that interrupts only
actually get disabled in the processor when an interrupt comes along.

When interrupts are enabled by local_irq_enable() et al., the code
sets the interrupts-enabled flag in the paca, and then checks whether
interrupts got hard-disabled.  If so, it also sets the EE bit in the
MSR to hard-enable the interrupts.

This has the potential to improve performance, and also makes it
easier to make a kernel that can boot on iSeries and on other 64-bit
machines, since this lazy-disable strategy is very similar to the
soft-disable strategy that iSeries already uses.

This version renames paca->proc_enabled to paca->soft_enabled, and
changes a couple of soft-disables in the kexec code to hard-disables,
which should fix the crash that Michael Ellerman saw.  This doesn't
yet use a reserved CR field for the soft_enabled and hard_enabled
flags.  This applies on top of Stephen Rothwell's patches to make it
possible to build a combined iSeries/other kernel.
Signed-off-by: Paul Mackerras <paulus@samba.org>

During boot we bring up all memory and cpu nodes. Normally a PCI device
will be in one of these online nodes, however in some weird setups it
may not.

We have only seen this in the lab but we may as well check for the case
and fallback to -1 (all nodes).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Instead of just checking that an address is in the right range, use the
provided __kernel_text_address() helper which covers both the kernel and
module text sections.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Change ->num_pmcs to match the number of PMCs in POWER6.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

At the moment we rely on a cpu feature bit or a firmware property to
detect altivec. If we dont have either of these and the cpu does in fact
support altivec we can cause a panic from userspace.

It seems safer to always send a signal if we manage to get an 0xf20
exception from userspace.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

When update_bridge_base() updates the IO window on a PCI-to-PCI
bridge, it fails to zero the upper 16 bits of the base and limit
registers if the window size is less than 64K.  This fixes it.
Signed-off-by: Paul Mackerras <paulus@samba.org>

Add missing entry in Makefile for MPC832x MDS support.  It
also change white space to tab in MPC8360 entry.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

MPC8360EMDS PB support is broken as some code was missing
in last submission.  This patch adds missing code and makes
MPC8360EMDS PB support working.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

In the timer_interrupt we were not calling set_irq_regs() and if we are
profiling we will end up calling get_irq_regs().  This causes bad things to
happen.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

A find -iname \*.[ch] | xargs grep "> ARRAY_SIZE(" revealed several
incorrect usages of ARRAY_SIZE in the mpc drivers.  The last element in the
array is always ARRAY_SIZE()-1, this patch modifies the bounds checks
accordingly.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The default configuration file for the MPC8349E-mITX reference board,
mpc834x_itx_defconfig, did not include support for DOS partition table types.
This support is necessary because the hard drive that comes with the ITX
is formatted with this partition table type.  Without this config option,
no partitions on the drive can be mounted.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This fixes a memory leak introduced by "spufs: add support
for read/write oncntl", which was missing a call to simple_attr_close.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The SPU code will crash if CONFIG_NUMA is not set and SPUs are found on
a non-0 node. This workaround will ignore those SPEs and just print an
message in the kernel log.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

I need this patch to get a UML kernel to compile.  This is with the
kernel headers in FC6 which are automatically generated from the kernel
tree.  Some headers are missing but those files don't need them.  At
least it appears so since the resuling kernel works fine.

Tested on x86-64.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

.. and clean up the file mapping code while at it.  No point in having a
"if (file)" repeated twice, and generally doing similar checks in two
different sections of the same code
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

It is silly to use non-static variable for writting zeroes to the file.

And more seriously, foffset in core dump file dump function was incremented
too much, so some parts of core dump were shifted by size of few phdrs and
notes down, so although gdb was able to load that file, it did not make lot
of sense - in my test case data pages were shifted down by about 900 bytes.
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (28 commits)
  ACPI: check battery status on resume for un/plug events during sleep
  ACPICA: Fix incorrect handling of PCI Express Root Bridge _HID
  ACPI: asus_acpi: don't printk on writing garbage to proc files
  ACPI: asus_acpi: fix proc files parsing
  ACPI: SCI interrupt source override
  ACPI: fix printk format warnings
  ACPI: fix section for CPU init functions
  ACPI: update comments in motherboard.c
  ACPI: acpi_pci_link_set() can allocate with either GFP_ATOMIC or GFP_KERNEL
  ACPI: fix potential OOPS in power driver with CONFIG_ACPI_DEBUG
  ACPI: ibm_acpi: delete obsolete documentation
  ACPI: created a dedicated workqueue for notify() execution
  ACPI: Remove deferred execution from global lock acquire wakeup path
  MSI S270 Laptop support: backlight, wlan, bluetooth states
  ACPI: EC: export ec_transaction() for msi-laptop driver
  ACPI: EC: Simplify acpi_hw_low_level*() with inb()/outb().
  ACPI: EC: Unify poll and interrupt gpe handlers
  ACPI: EC: Unify poll and interrupt mode transaction functions
  ACPI: EC: Remove unused variables and duplicated code
  ACPI: EC: Remove unnecessary delay added by previous transation patch.
  ...

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
  V4L/DVB (4750): AGC command1/2 is board specific
  V4L/DVB (4748): Fixed oops for Nova-T USB2
  V4L/DVB (4746): HM12 is YUV 4:2:0, not YUV 4:1:1
  V4L/DVB (4744): The Samsung TCPN2121P30A does not have a tda9887
  V4L/DVB (4743): Fix oops in VIDIOC_G_PARM
  V4L/DVB (4742): Drivers/media/video: handle sysfs errors
  V4L/DVB (4741): {ov511,stv680}: handle sysfs errors
  V4L/DVB (4740): Fixed an if-block to avoid floating with debug-messages
  V4L/DVB (4739): SECAM support for saa7113 into saa7115
  V4L/DVB (4738): Bt8xx/dvb-bt8xx.c: check kmalloc() return value.
  V4L/DVB (4734): Tda826x: fix frontend selection for dvb_attach
  V4L/DVB (4733): Tda10086: fix frontend selection for dvb_attach
  V4L/DVB (4732): Fix spelling error in Kconfig help text for DVB_CORE_ATTACH
  V4L/DVB (4731a): Kconfig: restore pvrusb2 menu items
  V4L/DVB (4729): Fix VIDIOC_G_FMT for NTSC in cx25840.
  V4L/DVB (4727): Support status readout for saa713x based FM radio
  V4L/DVB (4725): Fix vivi compile on parisc
  V4L/DVB (4692): Add WinTV-HVR3000 DVB-T support