When the current frame address (CFA) is stored on the stack (i.e.,
cfa->base == CFI_SP_INDIRECT), objtool neglects to adjust the stack
offset when there are subsequent pushes or pops.  This results in bad
ORC data at the end of the ENTER_IRQ_STACK macro, when it puts the
previous stack pointer on the stack and does a subsequent push.

This fixes the following unwinder warning:

  WARNING: can't dereference registers at 00000000f0a6bdba for ip interrupt_entry+0x9f/0xa0

Fixes: 627fce14 ("objtool: Add ORC unwind table generation")
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Reported-by: Dave Jones <dsj@fb.com>
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Reported-by: Joe Mario <jmario@redhat.com>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Jann Horn <jannh@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/853d5d691b29e250333332f09b8e27410b2d9924.1587808742.git.jpoimboe@redhat.com

Pull networking fixes from David Miller:

 1) Fix memory leak in netfilter flowtable, from Roi Dayan.

 2) Ref-count leaks in netrom and tipc, from Xiyu Yang.

 3) Fix warning when mptcp socket is never accepted before close, from
    Florian Westphal.

 4) Missed locking in ovs_ct_exit(), from Tonghao Zhang.

 5) Fix large delays during PTP synchornization in cxgb4, from Rahul
    Lakkireddy.

 6) team_mode_get() can hang, from Taehee Yoo.

 7) Need to use kvzalloc() when allocating fw tracer in mlx5 driver,
    from Niklas Schnelle.

 8) Fix handling of bpf XADD on BTF memory, from Jann Horn.

 9) Fix BPF_STX/BPF_B encoding in x86 bpf jit, from Luke Nelson.

10) Missing queue memory release in iwlwifi pcie code, from Johannes
    Berg.

11) Fix NULL deref in macvlan device event, from Taehee Yoo.

12) Initialize lan87xx phy correctly, from Yuiko Oshino.

13) Fix looping between VRF and XFRM lookups, from David Ahern.

14) etf packet scheduler assumes all sockets are full sockets, which is
    not necessarily true. From Eric Dumazet.

15) Fix mptcp data_fin handling in RX path, from Paolo Abeni.

16) fib_select_default() needs to handle nexthop objects, from David
    Ahern.

17) Use GFP_ATOMIC under spinlock in mac80211_hwsim, from Wei Yongjun.

18) vxlan and geneve use wrong nlattr array, from Sabrina Dubroca.

19) Correct rx/tx stats in bcmgenet driver, from Doug Berger.

20) BPF_LDX zero-extension is encoded improperly in x86_32 bpf jit, fix
    from Luke Nelson.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (100 commits)
  selftests/bpf: Fix a couple of broken test_btf cases
  tools/runqslower: Ensure own vmlinux.h is picked up first
  bpf: Make bpf_link_fops static
  bpftool: Respect the -d option in struct_ops cmd
  selftests/bpf: Add test for freplace program with expected_attach_type
  bpf: Propagate expected_attach_type when verifying freplace programs
  bpf: Fix leak in LINK_UPDATE and enforce empty old_prog_fd
  bpf, x86_32: Fix logic error in BPF_LDX zero-extension
  bpf, x86_32: Fix clobbering of dst for BPF_JSET
  bpf, x86_32: Fix incorrect encoding in BPF_LDX zero-extension
  bpf: Fix reStructuredText markup
  net: systemport: suppress warnings on failed Rx SKB allocations
  net: bcmgenet: suppress warnings on failed Rx SKB allocations
  macsec: avoid to set wrong mtu
  mac80211: sta_info: Add lockdep condition for RCU list usage
  mac80211: populate debugfs only after cfg80211 init
  net: bcmgenet: correct per TX/RX ring statistics
  net: meth: remove spurious copyright text
  net: phy: bcm84881: clear settings on link down
  chcr: Fix CPU hard lockup
  ...

Alexei Starovoitov says:

====================
pull-request: bpf 2020-04-24

The following pull-request contains BPF updates for your *net* tree.

We've added 17 non-merge commits during the last 5 day(s) which contain
a total of 19 files changed, 203 insertions(+), 85 deletions(-).

The main changes are:

1) link_update fix, from Andrii.

2) libbpf get_xdp_id fix, from David.

3) xadd verifier fix, from Jann.

4) x86-32 JIT fixes, from Luke and Wang.

5) test_btf fix, from Stanislav.

6) freplace verifier fix, from Toke.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 51c39bb1 ("bpf: Introduce function-by-function verification")
introduced function linkage flag and changed the error message from
"vlen != 0" to "Invalid func linkage" and broke some fake BPF programs.

Adjust the test accordingly.

AFACT, the programs don't really need any arguments and only look
at BTF for maps, so let's drop the args altogether.

Before:
BTF raw test[103] (func (Non zero vlen)): do_test_raw:3703:FAIL expected
err_str:vlen != 0
magic: 0xeb9f
version: 1
flags: 0x0
hdr_len: 24
type_off: 0
type_len: 72
str_off: 72
str_len: 10
btf_total_size: 106
[1] INT (anon) size=4 bits_offset=0 nr_bits=32 encoding=SIGNED
[2] INT (anon) size=4 bits_offset=0 nr_bits=32 encoding=(none)
[3] FUNC_PROTO (anon) return=0 args=(1 a, 2 b)
[4] FUNC func type_id=3 Invalid func linkage

BTF libbpf test[1] (test_btf_haskv.o): libbpf: load bpf program failed:
Invalid argument
libbpf: -- BEGIN DUMP LOG ---
libbpf:
Validating test_long_fname_2() func#1...
Arg#0 type PTR in test_long_fname_2() is not supported yet.
processed 0 insns (limit 1000000) max_states_per_insn 0 total_states 0
peak_states 0 mark_read 0

libbpf: -- END LOG --
libbpf: failed to load program 'dummy_tracepoint'
libbpf: failed to load object 'test_btf_haskv.o'
do_test_file:4201:FAIL bpf_object__load: -4007
BTF libbpf test[2] (test_btf_newkv.o): libbpf: load bpf program failed:
Invalid argument
libbpf: -- BEGIN DUMP LOG ---
libbpf:
Validating test_long_fname_2() func#1...
Arg#0 type PTR in test_long_fname_2() is not supported yet.
processed 0 insns (limit 1000000) max_states_per_insn 0 total_states 0
peak_states 0 mark_read 0

libbpf: -- END LOG --
libbpf: failed to load program 'dummy_tracepoint'
libbpf: failed to load object 'test_btf_newkv.o'
do_test_file:4201:FAIL bpf_object__load: -4007
BTF libbpf test[3] (test_btf_nokv.o): libbpf: load bpf program failed:
Invalid argument
libbpf: -- BEGIN DUMP LOG ---
libbpf:
Validating test_long_fname_2() func#1...
Arg#0 type PTR in test_long_fname_2() is not supported yet.
processed 0 insns (limit 1000000) max_states_per_insn 0 total_states 0
peak_states 0 mark_read 0

libbpf: -- END LOG --
libbpf: failed to load program 'dummy_tracepoint'
libbpf: failed to load object 'test_btf_nokv.o'
do_test_file:4201:FAIL bpf_object__load: -4007

Fixes: 51c39bb1 ("bpf: Introduce function-by-function verification")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200422003753.124921-1-sdf@google.com

Reorder include paths to ensure that runqslower sources are picking up
vmlinux.h, generated by runqslower's own Makefile. When runqslower is built
from selftests/bpf, due to current -I$(BPF_INCLUDE) -I$(OUTPUT) ordering, it
might pick up not-yet-complete vmlinux.h, generated by selftests Makefile,
which could lead to compilation errors like [0]. So ensure that -I$(OUTPUT)
goes first and rely on runqslower's Makefile own dependency chain to ensure
vmlinux.h is properly completed before source code relying on it is compiled.

  [0] https://travis-ci.org/github/libbpf/libbpf/jobs/677905925Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200422012407.176303-1-andriin@fb.com

Fix the following sparse warning:

kernel/bpf/syscall.c:2289:30: warning: symbol 'bpf_link_fops' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/1587609160-117806-1-git-send-email-zou_wei@huawei.com

In the prog cmd, the "-d" option turns on the verifier log.
This is missed in the "struct_ops" cmd and this patch fixes it.

Fixes: 65c93628 ("bpftool: Add struct_ops support")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Quentin Monnet <quentin@isovalent.com>
Link: https://lore.kernel.org/bpf/20200424182911.1259355-1-kafai@fb.com

This adds a new selftest that tests the ability to attach an freplace
program to a program type that relies on the expected_attach_type of the
target program to pass verification.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/158773526831.293902.16011743438619684815.stgit@toke.dk

For some program types, the verifier relies on the expected_attach_type of
the program being verified in the verification process. However, for
freplace programs, the attach type was not propagated along with the
verifier ops, so the expected_attach_type would always be zero for freplace
programs.

This in turn caused the verifier to sometimes make the wrong call for
freplace programs. For all existing uses of expected_attach_type for this
purpose, the result of this was only false negatives (i.e., freplace
functions would be rejected by the verifier even though they were valid
programs for the target they were replacing). However, should a false
positive be introduced, this can lead to out-of-bounds accesses and/or
crashes.

The fix introduced in this patch is to propagate the expected_attach_type
to the freplace program during verification, and reset it after that is
done.

Fixes: be8704ff ("bpf: Introduce dynamic program extensions")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/158773526726.293902.13257293296560360508.stgit@toke.dk

Fix bug of not putting bpf_link in LINK_UPDATE command.
Also enforce zeroed old_prog_fd if no BPF_F_REPLACE flag is specified.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200424052045.4002963-1-andriin@fb.com

When verifier_zext is true, we don't need to emit code
for zero-extension.

Fixes: 836256bf ("x32: bpf: eliminate zero extension code-gen")
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200423050637.GA4029@udknight

The current JIT clobbers the destination register for BPF_JSET BPF_X
and BPF_K by using "and" and "or" instructions. This is fine when the
destination register is a temporary loaded from a register stored on
the stack but not otherwise.

This patch fixes the problem (for both BPF_K and BPF_X) by always loading
the destination register into temporaries since BPF_JSET should not
modify the destination register.

This bug may not be currently triggerable as BPF_REG_AX is the only
register not stored on the stack and the verifier uses it in a limited
way.

Fixes: 03f5781b ("bpf, x86_32: add eBPF JIT compiler for ia32")
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Luke Nelson <luke.r.nels@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Wang YanQing <udknight@gmail.com>
Link: https://lore.kernel.org/bpf/20200422173630.8351-2-luke.r.nels@gmail.com

The current JIT uses the following sequence to zero-extend into the
upper 32 bits of the destination register for BPF_LDX BPF_{B,H,W},
when the destination register is not on the stack:

  EMIT3(0xC7, add_1reg(0xC0, dst_hi), 0);

The problem is that C7 /0 encodes a MOV instruction that requires a 4-byte
immediate; the current code emits only 1 byte of the immediate. This
means that the first 3 bytes of the next instruction will be treated as
the rest of the immediate, breaking the stream of instructions.

This patch fixes the problem by instead emitting "xor dst_hi,dst_hi"
to clear the upper 32 bits. This fixes the problem and is more efficient
than using MOV to load a zero immediate.

This bug may not be currently triggerable as BPF_REG_AX is the only
register not stored on the stack and the verifier uses it in a limited
way, and the verifier implements a zero-extension optimization. But the
JIT should avoid emitting incorrect encodings regardless.

Fixes: 03f5781b ("bpf, x86_32: add eBPF JIT compiler for ia32")
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Luke Nelson <luke.r.nels@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Acked-by: Wang YanQing <udknight@gmail.com>
Link: https://lore.kernel.org/bpf/20200422173630.8351-1-luke.r.nels@gmail.com

The patch fixes:
$ scripts/bpf_helpers_doc.py > bpf-helpers.rst
$ rst2man bpf-helpers.rst > bpf-helpers.7
bpf-helpers.rst:1105: (WARNING/2) Inline strong start-string without end-string.
Signed-off-by: Jakub Wilk <jwilk@jwilk.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Quentin Monnet <quentin@isovalent.com>
Link: https://lore.kernel.org/bpf/20200422082324.2030-1-jwilk@jwilk.net

The driver is designed to drop Rx packets and reclaim the buffers
when an allocation fails, and the network interface needs to safely
handle this packet loss. Therefore, an allocation failure of Rx
SKBs is relatively benign.

However, the output of the warning message occurs with a high
scheduling priority that can cause excessive jitter/latency for
other high priority processing.

This commit suppresses the warning messages to prevent scheduling
problems while retaining the failure count in the statistics of
the network interface.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver is designed to drop Rx packets and reclaim the buffers
when an allocation fails, and the network interface needs to safely
handle this packet loss. Therefore, an allocation failure of Rx
SKBs is relatively benign.

However, the output of the warning message occurs with a high
scheduling priority that can cause excessive jitter/latency for
other high priority processing.

This commit suppresses the warning messages to prevent scheduling
problems while retaining the failure count in the statistics of
the network interface.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a macsec interface is created, the mtu is calculated with the lower
interface's mtu value.
If the mtu of lower interface is lower than the length, which is needed
by macsec interface, macsec's mtu value will be overflowed.
So, if the lower interface's mtu is too low, macsec interface's mtu
should be set to 0.

Test commands:
    ip link add dummy0 mtu 10 type dummy
    ip link add macsec0 link dummy0 type macsec
    ip link show macsec0

Before:
    11: macsec0@dummy0: <BROADCAST,MULTICAST,M-DOWN> mtu 4294967274
After:
    11: macsec0@dummy0: <BROADCAST,MULTICAST,M-DOWN> mtu 0

Fixes: c09440f7 ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull SCSI fixes from James Bottomley:
 "Two minor fixes: one to update a Kconfig reference and the other to
  fix a resource leak on an error path in sg"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: Update referenced link to cdrtools
  scsi: sg: add sg_remove_request in sg_write

Pull power management fixes from Rafael Wysocki:
 "Restore an optimization related to asynchronous suspend and resume of
  devices during system-wide power transitions that was disabled by
  mistake (Kai-Heng Feng) and update the pm-graph suite of power
  management utilities (Todd Brandt)"

* tag 'pm-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM: sleep: core: Switch back to async_schedule_dev()
  pm-graph v5.6

Pull PNP cleanup from Rafael Wysocki:
 "Make the PNP code use list_for_each_entry() in a few places instead of
  open-coding it (Jason Gunthorpe)"

* tag 'pnp-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  pnp: Use list_for_each_entry() instead of open coding

Pull ACPI fixes from Rafael Wysocki:
 "Drop a lid status quirk for Asus T200TA that is not necessary any more
  and clean up a resource management inconsistency in the PCI IRQ link
  configuration code.

  Both changes from Hans de Goede"

* tag 'acpi-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: button: Drop no longer necessary Asus T200TA lid_init_state quirk
  ACPI/PCI: pci_link: use extended_irq union member when setting ext-irq shareable

IORING_OP_MADVISE can end up basically doing mprotect() on the VM of
another process, which means that it can race with our crazy core dump
handling which accesses the VM state without holding the mmap_sem
(because it incorrectly thinks that it is the final user).

This is clearly a core dumping problem, but we've never fixed it the
right way, and instead have the notion of "check that the mm is still
ok" using mmget_still_valid() after getting the mmap_sem for writing in
any situation where we're not the original VM thread.

See commit 04f5866e ("coredump: fix race condition between
mmget_not_zero()/get_task_mm() and core dumping") for more background on
this whole mmget_still_valid() thing.  You might want to have a barf bag
handy when you do.

We're discussing just fixing this properly in the only remaining core
dumping routines.  But even if we do that, let's make do_madvise() do
the right thing, and then when we fix core dumping, we can remove all
these mmget_still_valid() checks.
Reported-and-tested-by: Jann Horn <jannh@google.com>
Fixes: c1ca757b ("io_uring: add IORING_OP_MADVISE")
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'mac80211-for-net-2020-04-24' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Just three changes:
 * fix a wrong GFP_KERNEL in hwsim
 * fix the debugfs mess after the mac80211 registration race fix
 * suppress false-positive RCU list lockdep warnings
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-2020-04-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for v5.7

Second set of fixes for v5.7. Quite a few iwlwifi fixes and some
maintainers file updates.

iwlwifi

* fix a bug with kmemdup() error handling

* fix a DMA pool warning about unfreed memory

* fix beacon statistics

* fix a theoritical bug in device initialisation

* fix queue limit handling and inactive TID removal

* disable ACK Enabled Aggregation which was enabled by accident

* fix transmit power setting reading from BIOS with certain versions
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull io_uring fix from Jens Axboe:
 "Single fixup for a change that went into -rc2"

* tag 'io_uring-5.7-2020-04-24' of git://git.kernel.dk/linux-block:
  io_uring: only restore req->work for req that needs do completion

Pull libata fixlet from Jens Axboe:
 "Minor spelling error fix for libata"

* tag 'libata-5.7-2020-04-24' of git://git.kernel.dk/linux-block:
  ata: sata_inic162x fix a spelling issue

Pull block fixes from Jens Axboe:
 "A few fixes/changes that should go into this release:

   - null_blk zoned fixes (Damien)

   - blkdev_close() sync improvement (Douglas)

   - Fix regression in blk-iocost that impacted (at least) systemtap
     (Waiman)

   - Comment fix, header removal (Zhiqiang, Jianpeng)"

* tag 'block-5.7-2020-04-24' of git://git.kernel.dk/linux-block:
  null_blk: Cleanup zoned device initialization
  null_blk: Fix zoned command handling
  block: remove unused header
  blk-iocost: Fix error on iocost_ioc_vrate_adj
  bdev: Reduce time holding bd_mutex in sync in blkdev_close()
  buffer: remove useless comment and WB_REASON_FREE_MORE_MEM, reason.

Pull tracing fixes from Steven Rostedt:
 "A few tracing fixes:

   - Two fixes for memory leaks detected by kmemleak

   - Removal of some dead code

   - A few local functions turned static"

* tag 'trace-v5.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Convert local functions in tracing_map.c to static
  tracing: Remove DECLARE_TRACE_NOARGS
  ftrace: Fix memory leak caused by not freeing entry in unregister_ftrace_direct()
  tracing: Fix memory leaks in trace_events_hist.c

* acpi-pci:
  ACPI/PCI: pci_link: use extended_irq union member when setting ext-irq shareable

Pull arm64 fixes from Catalin Marinas:

 - Ensure context synchronisation after a write to APIAKey.

 - Fix bullet list formatting in Documentation/arm64/amu.rst to
   eliminate doc warnings.

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  Documentation: arm64: fix amu.rst doc warnings
  arm64: sync kernel APIAKey when installing

* pm-tools:
  pm-graph v5.6

Merge tag 'kbuild-fixes-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - fix scripts/config to properly handle ':' in string type CONFIG
   options

 - fix unneeded rebuilds of DT schema check rule

 - git rid of ordering dependency between <linux/vermagic.h> and
   <linux/module.h> to fix build errors in some network drivers

 - clean up generated headers of host arch with 'make ARCH=um mrproper'

* tag 'kbuild-fixes-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  h8300: ignore vmlinux.lds
  Documentation: kbuild: fix the section title format
  um: ensure `make ARCH=um mrproper` removes arch/$(SUBARCH)/include/generated/
  arch: split MODULE_ARCH_VERMAGIC definitions out to <asm/vermagic.h>
  kbuild: fix DT binding schema rule again to avoid needless rebuilds
  scripts/config: allow colons in option strings for sed

Pull misc AFS fixes from David Howells:
 "Three miscellaneous fixes to the afs filesystem:

   - Remove some struct members that aren't used, aren't set or aren't
     read, plus a wake up that nothing ever waits for.

   - Actually set the AFS_SERVER_FL_HAVE_EPOCH flag so that the code
     that depends on it can work.

   - Make a couple of waits uninterruptible if they're done for an
     operation that isn't supposed to be interruptible"

* tag 'afs-fixes-20200424' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  afs: Make record checking use TASK_UNINTERRUPTIBLE when appropriate
  afs: Fix to actually set AFS_SERVER_FL_HAVE_EPOCH
  afs: Remove some unused bits

Pull sound fixes from Takashi Iwai:
 "This became a slightly big pull request, as the accumulated ASoC fixes
  are included here. Some highlights:

   - Revert of ASoC DAI startup changes that caused regression on some
     x86 platforms

   - Regression fix in HD-audio power management and driver blacklist

   - A collection of ASoC DAPM and topology fixes

   - Continued USB-audio fixes and quirks

   - Lots of small device-specific fixes

   - Rockchip S/PDIF DT stuff update for validation issues"

* tag 'sound-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (51 commits)
  ALSA: hda: Always use jackpoll helper for jack update after resume
  ALSA: hda/realtek - Add new codec supported for ALC245
  ALSA: usb-audio: Fix usb audio refcnt leak when getting spdif
  ALSA: usb-audio: Add connector notifier delegation
  ALSA: usb-audio: Apply async workaround for Scarlett 2i4 2nd gen
  ASoC: wm8960: Fix wrong clock after suspend & resume
  ALSA: usx2y: Fix potential NULL dereference
  ALSA: usb-audio: Add quirk for Focusrite Scarlett 2i2
  ASoC: wm89xx: Add missing dependency
  ASoC: dapm: fixup dapm kcontrol widget
  ASoC: rsnd: Fix "status check failed" spam for multi-SSI
  ASoC: rsnd: Don't treat master SSI in multi SSI setup as parent
  ASoC: meson: gx-card: fix codec-to-codec link setup
  ASoC: meson: axg-card: fix codec-to-codec link setup
  ALSA: usb-audio: Add static mapping table for ALC1220-VB-based mobos
  ALSA: hda: Remove ASUS ROG Zenith from the blacklist
  ALSA: hda/realtek - Fix unexpected init_amp override
  ALSA: usb-audio: Filter out unsupported sample rates on Focusrite devices
  ASoC: SOF: Intel: add min/max channels for SSP on Baytrail/Broadwell
  ASoC: stm32: sai: fix sai probe
  ...

Pull drm fixes from Dave Airlie:
 "Weekly regular fixes for drm, The usual rc3 uptick here, but nothing
  too crazy or notable.

  core:
   - mst: zero pbn when releasing vcpi slots

  amdgpu:
   - Fix resume issue on renoir
   - Thermal fix for older CI dGPUs
   - Fix some fallout from dropping drm load/unload callbacks

  i915:
   - Tigerlake Workaround - disabling media recompression (Matt)
   - Fix RPS interrupts for right GPU frequency (Chris)
   - HDCP fix prime check (Oliver)
   - Tigerlake Thunderbolt power well fix (Matt)
   - Tigerlake DP link training fixes (Jose)
   - Documentation sphinx build fix (Jani)
   - Fix enable_dpcd_backlight modparam (Lyude)

  analogix-dp:
   - binding fix

  meson:
   - remove unneeded error message

  bindings:
   - fix warnings
   - fix lvds binding

  scheduler:
   - thread racing fix

  tidss:
   - use after free fix"

* tag 'drm-fixes-2020-04-24' of git://anongit.freedesktop.org/drm/drm:
  drm/i915/dpcd_bl: Unbreak enable_dpcd_backlight modparam
  drm/i915: fix Sphinx build duplicate label warning
  drm/i915/display: Load DP_TP_CTL/STATUS offset before use it
  drm/i915/tgl: TBT AUX should use TC power well ops
  drm/i915: HDCP: fix Ri prime check done during link check
  drm/i915/gt: Update PMINTRMSK holding fw
  drm/i915/tgl: Add Wa_14010477008:tgl
  drm/tidss: fix crash related to accessing freed memory
  drm/dp_mst: Zero assigned PBN when releasing VCPI slots
  drm/amdgpu/display: give aux i2c buses more meaningful names
  drm/amdgpu/display: fix aux registration (v2)
  drm/amdgpu: Correctly initialize thermal controller for GPUs with Powerplay table v0 (e.g Hawaii)
  drm/amd/powerplay: fix resume failed as smu table initialize early exit
  drm/scheduler: fix drm_sched_get_cleanup_job
  drm/meson: Delete an error message in meson_dw_hdmi_bind()
  drm/bridge: anx6345: set correct BPC for display_info of connector
  dt-bindings: display: allow port and ports in panel-lvds
  dt-bindings: display: xpp055c272: Remove the reg property
  dt-bindings: display: ltk500hd1829: Remove the reg property
  drm/bridge: analogix_dp: Split bind() into probe() and real bind()

When an operation is meant to be done uninterruptibly (such as
FS.StoreData), we should not be allowing volume and server record checking
to be interrupted.

Fixes: d2ddc776 ("afs: Overhaul volume and server record caching and fileserver rotation")
Signed-off-by: David Howells <dhowells@redhat.com>

AFS keeps track of the epoch value from the rxrpc protocol to note (a) when
a fileserver appears to have restarted and (b) when different endpoints of
a fileserver do not appear to be associated with the same fileserver
(ie. all probes back from a fileserver from all of its interfaces should
carry the same epoch).

However, the AFS_SERVER_FL_HAVE_EPOCH flag that indicates that we've
received the server's epoch is never set, though it is used.

Fix this to set the flag when we first receive an epoch value from a probe
sent to the filesystem client from the fileserver.

Fixes: 3bf0fb6f ("afs: Probe multiple fileservers simultaneously")
Signed-off-by: David Howells <dhowells@redhat.com>

Remove three bits:

 (1) afs_server::no_epoch is neither set nor used.

 (2) afs_server::have_result is set and a wakeup is applied to it, but
     nothing looks at it or waits on it.

 (3) afs_vl_dump_edestaddrreq() prints afs_addr_list::probed, but nothing
     sets it for VL servers.
Signed-off-by: David Howells <dhowells@redhat.com>

The function sta_info_get_by_idx() uses RCU list primitive.
It is called with  local->sta_mtx held from mac80211/cfg.c.
Add lockdep expression to avoid any false positive RCU list warnings.
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Link: https://lore.kernel.org/r/20200409082906.27427-1-madhuparnabhowmik10@gmail.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>

When fixing the initialization race, we neglected to account for
the fact that debugfs is initialized in wiphy_register(), and
some debugfs things went missing (or rather were rerooted to the
global debugfs root).

Fix this by adding debugfs entries only after wiphy_register().
This requires some changes in the rate control code since it
currently adds debugfs at alloc time, which can no longer be
done after the reordering.
Reported-by: Jouni Malinen <j@w1.fi>
Reported-by: kernel test robot <rong.a.chen@intel.com>
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Felix Fietkau <nbd@nbd.name>
Cc: stable@vger.kernel.org
Fixes: 52e04b4c ("mac80211: fix race in ieee80211_register_hw()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/20200423111344.0e00d3346f12.Iadc76a03a55093d94391fc672e996a458702875d@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>