- 30 Dec, 2016 14 commits
-
-
Stanislaw Gruszka authored
We need to perform different actions (AGC and VCO calibrations and VGC tuning) periodically at different intervals. We don't need separate works for those, we can use link tuner work and just check for proper interval on it. This fixes performing AGC and VCO calibration when scanning on STA mode. We need to be on-channel to perform those calibrations. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Since we reset TX_PIN_CFG register, we have to finish recalibration. Warn if this is not possible. Signed-off-by:
-
Stanislaw Gruszka authored
We have different modes of adjusting freq offset on different chips. Call current adjustment similarly like vendor driver - mode1 . Signed-off-by:
-
Stanislaw Gruszka authored
MAX_LEN_CFG_MAX_PSDU specify maximum transmitted by HW AMPDU length (0 - 8kB, 1 - 16kB, 2 - 32kB, 3 - 64kB). Set this option according to remote stations capabilities (based on HT ampdu_factor). However limit the value based our hardware TX capabilities as some chips can not send more than 16kB (factor 1). Limit for all chips is currently 32kB (factor 2), but perhaps for some chips this could be increased to 64kB by setting drv_data->max_psdu to 3. Since MAX_LEN_CFG_MAX_PSDU is global setting, on multi stations modes (AP, IBSS, mesh) we limit according to less capable remote STA. We can not set bigger value to speed up communication with some stations and do not break communication with slow stations. Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Do not set ampdu_density and ba_size for frames without AMPDU bit i.e. frames that will not be aggregated to AMPDU. Signed-off-by:
-
Stanislaw Gruszka authored
Initalize max ampdu_factor supported by us based on rx chains, vendor driver do the same. Signed-off-by:
-
Andrew Lutomirski authored
Eric Biggers pointed out that the orinoco driver pointed scatterlists at the stack. Fix it by switching from ahash to shash. The result should be simpler, faster, and more correct. Cc: stable@vger.kernel.org # 4.9 only Reported-by:
Eric Biggers <ebiggers3@gmail.com> Signed-off-by:
Andy Lutomirski <luto@kernel.org> Signed-off-by:
-
Dan Carpenter authored
We accidentally return success when adm8211_alloc_rings() fails but we should preserve the error code. Fixes: cc0b88cf ("[PATCH] Add adm8211 802.11b wireless driver") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Johannes Berg authored
There's no need for this to be only __read_mostly, since it's only written in a single way depending on the module parameter, so that can be moved into the module's __init function, and the ops can be __ro_after_init. This is a little bit safer since it means the ops can't be overwritten (accidentally or otherwise), which would otherwise cause an arbitrary function or bad pointer to be called. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Acked-by:
-
Amitkumar Karwar authored
Enable dynamic bandwidth signalling by setting the corresponding bit in MAC control register. Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
-
Amitkumar Karwar authored
Firmware has started making use of reserved field. Accordingly change curr_pkt_filter from u16 to u32. Signed-off-by:
-
Amitkumar Karwar authored
If we have sdio work requests received when sdio card reset is happening, we may end up accessing older save_adapter pointer later which is already freed during card reset. This patch solves the problem by cancelling those pending requests. Signed-off-by:
-
- 05 Dec, 2016 2 commits
-
-
Alexey Khoroshilov authored
The driver does not check if mapping dma memory succeed. The patch adds the checks and failure handling. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
-
Dan Carpenter authored
These lines were indented one tab extra. Signed-off-by:
-
- 04 Dec, 2016 24 commits
-
-
Erik Nordmark authored
Implemented RFC7527 Enhanced DAD. IPv6 duplicate address detection can fail if there is some temporary loopback of Ethernet frames. RFC7527 solves this by including a random nonce in the NS messages used for DAD, and if an NS is received with the same nonce it is assumed to be a looped back DAD probe and is ignored. RFC7527 is enabled by default. Can be disabled by setting both of conf/{all,interface}/enhanced_dad to zero. Signed-off-by:Erik Nordmark <nordmark@arista.com> Signed-off-by:
Bob Gilligan <gilligan@arista.com> Reviewed-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Andrew Lunn says: ==================== mv88e6390 batch 3 More patches to support the MV88e6390. This is mostly refactoring existing code and adding implementations for the mv88e6390. This patchset set which reserved frames are sent to the cpu, the size of jumbo frames that will be accepted, turn off egress rate limiting, and configuration of pause frames. ==================== Signed-off-by: -
Andrew Lunn authored
The mv88e6390 has a number flow control registers accessed via the Flow Control register. Use these to set the pause control. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Andrew Lunn authored
The mv88e6390 has a different mechanism for configuring pause. Refactor the code into an ops function, and for the moment, don't add any mv88e6390 code yet. Signed-off-by:
-
Andrew Lunn authored
There are two different rate limiting configurations, depending on the switch generation. Refactor this into ops. Signed-off-by:
-
Andrew Lunn authored
Some switches support jumbo frames. Refactor this code into operations in the ops structure. Signed-off-by:
-
Andrew Lunn authored
Older devices have a couple of registers in global2. The mv88e6390 family has a single register in global1 behind which hides similar configuration. Implement and op for this. Signed-off-by:
-
David S. Miller authored
Andrew Lunn says: ==================== MV88E6390 batch two This is the second batch of patches adding support for the MV88e6390. They are not sufficient to make it work properly. The mv88e6390 has a much expanded set of priority maps. Refactor the existing code, and implement basic support for the new device. Similarly, the monitor control register has been reworked. The mv88e6390 has something odd in its EDSA tagging implementation, which means it is not possible to use it. So we need to use DSA tagging. This is the first device with EDSA support where we need to use DSA, and the code does not support this. So two patches refactor the existing code. The two different register definitions are separated out, and using DSA on an EDSA capable device is added. v2: Add port prefix Add helper function for 6390 Add _IEEE_ into #defines Split monitor_ctrl into a number of separate ops. Remove 6390 code which is management, used in a later patch s/EGREES/EGRESS/. Broke up setup_port_dsa() and set_port_dsa() into a number of ops v3: Verify mandatory ops for port setup Don't set ether type for DSA port. ==================== Signed-off-by: -
Andrew Lunn authored
Older chips only support DSA tagging. Newer chips have both DSA and EDSA tagging. Refactor the code by adding port functions for setting the frame mode, egress mode, and if to forward unknown frames. This results in the helper mv88e6xxx_6065_family() becoming unused, so remove it. Signed-off-by:
-
Andrew Lunn authored
Older chips support a single tagging protocol, DSA. New chips support both DSA and EDSA, an enhanced version. Having both as an option changes the register layouts. Up until now, it has been assumed that if EDSA is supported, it will be used. Hence the register layout has been determined by which protocol should be used. However, mv88e6390 has a different implementation of EDSA, which requires we need to use the DSA tagging. Hence separate the selection of the protocol from the register layout. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
-
Andrew Lunn authored
The mv88e6390 changes the monitor control register into the Monitor and Management control, which is an indirection register to various registers. Add ops to set the CPU port and the ingress/egress port for both register layouts, to global1 Signed-off-by:
-
Andrew Lunn authored
The mv88e6390 does not have the two registers to set the frame priority map. Instead it has an indirection registers for setting a number of different priority maps. Refactor the old code into an function, implement the mv88e6390 version, and use an op to call the right one. Signed-off-by:
-
David S. Miller authored
Jiri Pirko says: ==================== ipv4: fib: Replay events when registering FIB notifier Ido says: In kernel 4.9 the switchdev-specific FIB offload mechanism was replaced by a new FIB notification chain to which modules could register in order to be notified about the addition and deletion of FIB entries. The motivation for this change was that switchdev drivers need to be able to reflect the entire FIB table and not only FIBs configured on top of the port netdevs themselves. This is useful in case of in-band management. The fundamental problem with this approach is that upon registration listeners lose all the information previously sent in the chain and thus have an incomplete view of the FIB tables, which can result in packet loss. This patchset fixes that by dumping the FIB tables and replaying notifications previously sent in the chain for the registered notification block. The entire dump process is done under RCU and thus the FIB notification chain is converted to be atomic. The listeners are modified accordingly. This is done in the first eight patches. The ninth patch adds a change sequence counter to ensure the integrity of the FIB dump. The last patch adds the dump itself to the FIB chain registration function and modifies existing listeners to pass a callback to be executed in case dump was inconsistent. --- v3->v4: - Register the notification block after the dump and protect it using the change sequence counter (Hannes Frederic Sowa). - Since we now integrate the dump into the registration function, drop the sysctl to set maximum number of retries and instead set it to a fixed number. Lets see if it's really a problem before adding something we can never remove. - For the same reason, dump FIB tables for all net namespaces. - Add a comment regarding guarantees provided by mutex semantics. v2->v3: - Add sysctl to set the number of FIB dump retries (Hannes Frederic Sowa). - Read the sequence counter under RTNL to ensure synchronization between the dump process and other processes changing the routing tables (Hannes Frederic Sowa). - Pass a callback to the dump function to be executed prior to a retry. - Limit the dump to a single net namespace. v1->v2: - Add a sequence counter to ensure the integrity of the FIB dump (David S. Miller, Hannes Frederic Sowa). - Protect notifications from re-ordering in listeners by using an ordered workqueue (Hannes Frederic Sowa). - Introduce fib_info_hold() (Jiri Pirko). - Relieve rocker from the need to invoke the FIB dump by registering to the FIB notification chain prior to ports creation. ==================== Signed-off-by: -
Ido Schimmel authored
Commit b90eb754 ("fib: introduce FIB notification infrastructure") introduced a new notification chain to notify listeners (f.e., switchdev drivers) about addition and deletion of routes. However, upon registration to the chain the FIB tables can already be populated, which means potential listeners will have an incomplete view of the tables. Solve that by dumping the FIB tables and replaying the events to the passed notification block. The dump itself is done using RCU in order not to starve consumers that need RTNL to make progress. The integrity of the dump is ensured by reading the FIB change sequence counter before and after the dump under RTNL. This allows us to avoid the problematic situation in which the dumping process sends a ENTRY_ADD notification following ENTRY_DEL generated by another process holding RTNL. Callers of the registration function may pass a callback that is executed in case the dump was inconsistent with current FIB tables. The number of retries until a consistent dump is achieved is set to a fixed number to prevent callers from looping for long periods of time. In case current limit proves to be problematic in the future, it can be easily converted to be configurable using a sysctl. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Ido Schimmel authored
The next patch will enable listeners of the FIB notification chain to request a dump of the FIB tables. However, since RTNL isn't taken during the dump, it's possible for the FIB tables to change mid-dump, which will result in inconsistency between the listener's table and the kernel's. Allow listeners to know about changes that occurred mid-dump, by adding a change sequence counter to each net namespace. The counter is incremented just before a notification is sent in the FIB chain. Signed-off-by:
-
Ido Schimmel authored
In order not to hold RTNL for long periods of time we're going to dump the FIB tables using RCU. Convert the FIB notification chain to be atomic, as we can't block in RCU critical sections. Signed-off-by:
-
Ido Schimmel authored
We can miss FIB notifications sent between the time the ports were created and the FIB notification block registered. Instead of receiving these notifications only when they are replayed for the FIB notification block during registration, just register the notification block before the ports are created. Signed-off-by:
-
Ido Schimmel authored
Convert rocker to offload FIBs in deferred work in a similar fashion to mlxsw, which was converted in the previous commits. Signed-off-by:
-
Ido Schimmel authored
As explained in the previous commits, we need to process FIB entries addition / deletion events in FIFO order or otherwise we can have a mismatch between the kernel's FIB table and the device's. Create an ordered workqueue for rocker to which these work items will be submitted to. Signed-off-by:
-
Ido Schimmel authored
FIB offload is currently done in process context with RTNL held, but we're about to dump the FIB tables in RCU critical section, so we can no longer sleep. Instead, defer the operation to process context using deferred work. Make sure fib info isn't freed while the work is queued by taking a reference on it and releasing it after the operation is done. Deferring the operation is valid because the upper layers always assume the operation was successful. If it's not, then the driver-specific abort mechanism is called and all routed traffic is directed to slow path. The work items are submitted to an ordered workqueue to prevent a mismatch between the kernel's FIB table and the device's. Signed-off-by:
-
Ido Schimmel authored
We're going to start processing FIB entries addition / deletion events in deferred work. These work items must be processed in the order they were submitted or otherwise we can have differences between the kernel's FIB table and the device's. Solve this by creating an ordered workqueue to which these work items will be submitted to. Note that we can't simply convert the current workqueue to be ordered, as EMADs re-transmissions are also processed in deferred work. Later on, we can migrate other work items to this workqueue, such as FDB notification processing and nexthop resolution, since they all take the same lock anyway. Signed-off-by:
-
Ido Schimmel authored
As explained in the previous commit, modules are going to need to take a reference on fib info and then drop it using fib_info_put(). Add the fib_info_hold() helper to make the code more readable and also symmetric with fib_info_put(). Signed-off-by:
-
Ido Schimmel authored
The FIB notification chain is going to be converted to an atomic chain, which means switchdev drivers will have to offload FIB entries in deferred work, as hardware operations entail sleeping. However, while the work is queued fib info might be freed, so a reference must be taken. To release the reference (and potentially free the fib info) fib_info_put() will be called, which in turn calls free_fib_info(). Export free_fib_info() so that modules will be able to invoke fib_info_put(). Signed-off-by:
-
WANG Cong authored
Fixes: 255cb304 ("net/sched: act_mirred: Add new tc_action_ops get_dev()") Cc: Hadar Hen Zion <hadarh@mellanox.com> Cc: Jiri Pirko <jiri@mellanox.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
