- 13 May, 2022 26 commits
-
-
Jani Nikula authored
We'll need to propagate drm_edid everywhere. v2: Rebase Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Reviewed-by:
Ankit Nautiyal <ankit.k.nautiyal@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/a52a6882e87a4bb6b1670918f3aba13f9b52f6de.1652097712.git.jani.nikula@intel.com
-
Jani Nikula authored
We'll need to propagate drm_edid everywhere. v2: Handle NULL EDID pointer (Ville, CI) Signed-off-by:
-
Jani Nikula authored
We'll need to propagate drm_edid everywhere. v2: Rebase Signed-off-by:
-
Jani Nikula authored
We'll need to propagate drm_edid everywhere. v2: Handle NULL drm_edid Signed-off-by:
-
Jani Nikula authored
We'll need to propagate drm_edid everywhere. v2: Handle NULL EDID pointer (Ville, CI) Signed-off-by:
-
Jani Nikula authored
We'll need to propagate drm_edid everywhere. v2: Handle NULL EDID pointer (Ville, CI) Signed-off-by:
-
Jani Nikula authored
We'll need to propagate drm_edid everywhere.' v2: Handle NULL EDID pointer (Ville, CI) Signed-off-by:
-
Jani Nikula authored
We'll need to propagate drm_edid everywhere. v2: Handle NULL EDID pointer (Ville, CI) Signed-off-by:
-
Jani Nikula authored
We'll need to propagate drm_edid everywhere. v2: Fix checkpatch warning on superfluous parens Signed-off-by:
-
Jani Nikula authored
We'll need to propagate drm_edid everywhere. v2: Drop incorrect NULL name check (Dan Carpenter) Signed-off-by:
-
Jani Nikula authored
We'll need to propagate drm_edid everywhere. Signed-off-by:
-
Jani Nikula authored
We'll need to propagate drm_edid everywhere. Signed-off-by:
-
Jani Nikula authored
We'll need to propagate drm_edid everywhere. Signed-off-by:
-
Jani Nikula authored
We'll need to propagate drm_edid everywhere. Signed-off-by:
-
Jani Nikula authored
We'll need to propagate drm_edid everywhere. Signed-off-by:
-
Jani Nikula authored
We'll need to propagate drm_edid everywhere. Signed-off-by:
-
Jani Nikula authored
We'll need to propagate drm_edid everywhere. Signed-off-by:
-
Jani Nikula authored
We'll need to propagate drm_edid everywhere. v3: s/edid/drm_edid/ in comment too (Ankit) Signed-off-by:
-
Jani Nikula authored
We'll need to propagate drm_edid everywhere. v3: Rebase Signed-off-by:
-
Jani Nikula authored
We'll need to propagate drm_edid everywhere. v3: Update comment to refer to update_display_info() (Ankit) v2: Use drm_edid_legacy_init() Signed-off-by:
-
Jani Nikula authored
We'll need to propagate drm_edid everywhere. This is a clunky start, but a start nonetheless. We'll eventually convert all of the EDID parsing to struct drm_edid. Initially, we'll just create the struct drm_edid in stack. This will be the compat layer for legacy struct edid code. In the future, we'll have EDID read return drm_edid objects. v2: Add legacy init helper. Signed-off-by:
-
Jani Nikula authored
Introduce new opaque type struct drm_edid to encapsulate the EDID data and the size allocated for it. The contents will be private to drm_edid.c. There are a number of reasons for adding a container around struct edid: * struct edid is a raw blob pointer to data that usually originates outside of the kernel. Its size is contained within the structure. * There's no way to attach meta information (such as allocated memory size) to struct edid. * Validation of the EDID blob and its size become crucial, and it's spread all over the subsystem, with varying levels of accuracy. * HDMI Forum has introduced an HF-EEODB extension that defines an override EDID size within an EDID extension. The size allocated for an EDID depends on whether the allocator understands the HF-EEODB extension. Given a struct edid *, it's impossible to know how much memory was actually allocated for it. There are also some reasons for making the container type struct drm_edid opaque and private to drm_edid.c: * Have only one place for creating and parsing the EDID, to avoid duplicating bugs. * Prepare for reading a pure DisplayID 2.0 from its own DDC address, and adding it within the same struct drm_edid container, transparently, and for all drivers. * With the idea that the drm_edid objects are immutable during their lifetimes, it will be possible to refcount them and reduce EDID copying everywhere (this is left for future work). Initially, just add the type. In follow-up, we'll start converting the guts of drm_edid.c to use it, and finally add interfaces around it. Signed-off-by:
-
Jani Nikula authored
We have an iterator for this, use it. It does include the base block, but its tag is 0 and will be skipped. Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/a68718819a3dbfbdaaaddca7f73afa5ac6b33d07.1652097712.git.jani.nikula@intel.com
-
Jani Nikula authored
Only one of the conditions can be true. Suggested-by:
-
Javier Martinez Canillas authored
The driver has runtime but no build time dependency with X86, so it can be built for testing purposes if the COMPILE_TEST option is enabled. This is useful to have more build coverage and make sure that the driver is not affected by changes that could cause build regressions. Signed-off-by:
Javier Martinez Canillas <javierm@redhat.com> Acked-by:
Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220505120419.314136-1-javierm@redhat.com
-
Javier Martinez Canillas authored
Drivers that want to remove registered conflicting framebuffers prior to register their own framebuffer, call to remove_conflicting_framebuffers(). This function takes the registration_lock mutex, to prevent a race when drivers register framebuffer devices. But if a conflicting framebuffer device is found, the underlaying platform device is unregistered and this will lead to the platform driver .remove callback to be called. Which in turn will call to unregister_framebuffer() that takes the same lock. To prevent this, a struct fb_info.forced_out field was used as indication to unregister_framebuffer() whether the mutex has to be grabbed or not. But this could be unsafe, since the fbdev core is making assumptions about what drivers may or may not do in their .remove callbacks. Allowing to run these callbacks with the registration_lock held can cause deadlocks, since the fbdev core has no control over what drivers do in their removal path. A better solution is to drop the lock before platform_device_unregister(), so unregister_framebuffer() can take it when called from the fbdev driver. The lock is acquired again after the device has been unregistered and at this point the removal loop can be restarted. Since the conflicting framebuffer device has already been removed, the loop would just finish when no more conflicting framebuffers are found. Suggested-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
- 12 May, 2022 6 commits
-
-
Marek Vasut authored
Implement DSI-to-e(DP) mode, which is a mix of currently supported DSI-to-DPI and DPI-to-(e)DP modes. The input side is configured as either DSI or DPI, the DP AUX channel is registered for both input side options, and the DSI host is attached for both DPI and (e)DP output side options. One notable detail is that the DSI-to-(e)DP mode requires the Pixel PLL to be always enabled, which is not needed for DPI-to-(e)DP mode which gets the matching clock direct from DPI Pixel Clock instead. Signed-off-by:
Marek Vasut <marex@denx.de> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Marek Vasut <marex@denx.de> Cc: Maxime Ripard <maxime@cerno.tech> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Robert Foss <robert.foss@linaro.org> Cc: Sam Ravnborg <sam@ravnborg.org> Signed-off-by:
Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220429205644.245480-2-marex@denx.de
-
Marek Vasut authored
Factor out register programming to configure the chip video RX side for reception of video data from DSI or DPI. This is particularly useful in the (e)DP output mode, where the video data can be received from either DPI or DSI. While only the former is supported in (e)DP output mode so far, this patch is added in preparation for addition of the later. There is a change in the order or register programming in case of the DSI-to-DPI mode. The DSI RX side is now programmed and enabled all in one place after the output mode has been configured. Before this change, the DSI RX has been programmed before the output mode has been set and only enabled afterward. The order makes no difference however, since the DSI RX is only enabled at the end either way. Signed-off-by:
-
Jocelyn Falempe authored
Some MGA200 hardware is broken and can't use a start address > 0. v2: Warn if startaddr is not 0, and hw doesn't support it. (instead of removing MGAG200_FLAG_HW_BUG_NO_STARTADD) Signed-off-by:
Jocelyn Falempe <jfalempe@redhat.com> Reviewed-by:
-
Jocelyn Falempe authored
When there are multiple damage clips, previous code merged them into one big rectangle. As the Matrox memory is very slow, it's faster to copy each damage clip. Signed-off-by:
Lyude Paul <lyude@redhat.com> Reviewed-by:
-
Jocelyn Falempe authored
The driver does support damage clips, but doesn't advertise it. So when running gnome/wayland on Matrox hardware, the full frame is copied to the slow Matrox memory, which leads to very poor performances. Add drm_plane_enable_fb_damage_clips() to advertise this capability to userspace. With this patch, gnome/wayland becomes usable on Matrox GPU. Suggested-by:
Jonas Ådahl <jadahl@gmail.com> Signed-off-by:
-
Melissa Wen authored
I've been contributing to v3d through improvements, reviews, testing, debugging, etc. So, I'm adding myself as a co-maintainer of the V3D driver. Signed-off-by:
Melissa Wen <mwen@igalia.com> Acked-by:
Juan A. Suarez <jasuarez@igalia.com> Acked-by:
Iago Toral Quiroga <itoral@igalia.com> Signed-off-by:
Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20220429193317.ol3u4e5jpt5jucox@mail.igalia.com
-
- 11 May, 2022 6 commits
-
-
Jayshri Pawar authored
Add support for pre_enable and post_enable drm bridge control functions. Making sure that host to be prepared before panel is powered up, for the panels like TC358762. Signed-off-by:
Jayshri Pawar <jpawar@cadence.com> Reviewed-by:
-
Javier Martinez Canillas authored
Many of the kselftests in DRM can be converted to kunit tests instead, since that framework is more suitable for unit testing. Suggested-by:
-
Javier Martinez Canillas authored
Thomas asked me to serve as co-maintainer for the simpledrm driver. Signed-off-by:
-
Christian König authored
No need to have those in the header. Signed-off-by:
Christian König <christian.koenig@amd.com> Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Reviewed-by:
Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220510113649.879821-2-christian.koenig@amd.com
-
Christian König authored
We still need to calculate a virtual start address for the resource to aid checking of it is visible or not. Only matters on small BAR systems, but better save than sorry. Signed-off-by:
-
Christian König authored
This gives us the standard atomic implicit and explicit fencing rules. v2: move the wait to amdgpu_dm_atomic_commit_tail Signed-off-by:
-
- 10 May, 2022 2 commits
-
-
Minghao Chi authored
Simplify the return expression. Reported-by:
Zeal Robot <zealci@zte.com.cn> Signed-off-by:
Minghao Chi <chi.minghao@zte.com.cn> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Signed-off-by:
-
Yuanzheng Song authored
'cat /sys/kernel/debug/dma_buf/bufinfo' will print the Dma-buf Objects' information when the CONFIG_DEBUG_FS=y. However, the printed table header information does not contain the name field. So we need to add the name field to the table header and use the '<none>' to replace the empty buf_obj->name. Signed-off-by:
Yuanzheng Song <songyuanzheng@huawei.com> Reviewed-by:
Sumit Semwal <sumit.semwal@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220428063924.3570409-1-songyuanzheng@huawei.com
-
