This argument of ath10k_htt_rx_h_frag_pn_check() is always set to 0 so
drop this.
Signed-off-by: Zhi-Jun You <hujy652@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221110164025.14418-1-hujy652@gmail.com

This driver is attempting to register to support two different buses.
if either of these is successful then ath10k_pci_init() should return 0
so that hardware attached to the successful bus can be probed and
supported. only if both of these are unsuccessful should ath10k_pci_init()
return an errno.

Fixes: 0b523ced ("ath10k: add basic skeleton to support ahb")
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221110061926.18163-1-xiujianfeng@huawei.com

Use IEEE80211_SEQ_TO_SN() macro to convert seq_ctrl to sn for better
readability.
Signed-off-by: Zhi-Jun You <hujy652@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221106162227.1119-1-hujy652@gmail.com

Variable mismatch is just being incremented and it's never used anywhere
else. The variable and the increment are redundant so remove it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221104140723.226857-1-colin.i.king@gmail.com

Currently after the hardware restart triggered from the driver, the
station interface connection remains intact, since a disconnect trigger
is not sent to userspace. This can lead to a problem in targets where
the wifi mac sequence is added by the firmware.

After the target restart, its wifi mac sequence number gets reset to
zero. Hence AP to which our device is connected will receive frames with
a  wifi mac sequence number jump to the past, thereby resulting in the
AP dropping all these frames, until the frame arrives with a wifi mac
sequence number which AP was expecting.

To avoid such frame drops, its better to trigger a station disconnect
upon target hardware restart which can be done with API
ieee80211_reconfig_disconnect exposed to mac80211.

The other targets are not affected by this change, since the hardware
params flag is not set.
Reported-by: kernel test robot <lkp@intel.com>

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Youghandhar Chintala <quic_youghand@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221104085403.11025-1-quic_youghand@quicinc.com

Commit ff6d3658 ("soc: qcom: qmi: use const for struct
qmi_elem_info") allows QMI message encoding/decoding rules to be
const, so do that for ath11k.

Compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220915002303.12206-1-quic_jjohnson@quicinc.com

Commit ff6d3658 ("soc: qcom: qmi: use const for struct
qmi_elem_info") allows QMI message encoding/decoding rules
to be const, so do that for ath10k.

Compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220915002612.13394-1-quic_jjohnson@quicinc.com

ath11k_mac_he_gi_to_nl80211_he_gi() generates a valid warning with gcc-13:
  drivers/net/wireless/ath/ath11k/mac.c:321:20: error: conflicting types for 'ath11k_mac_he_gi_to_nl80211_he_gi' due to enum/integer mismatch; have 'enum nl80211_he_gi(u8)'
  drivers/net/wireless/ath/ath11k/mac.h:166:5: note: previous declaration of 'ath11k_mac_he_gi_to_nl80211_he_gi' with type 'u32(u8)'

I.e. the type of the return value ath11k_mac_he_gi_to_nl80211_he_gi() in
the declaration is u32, while the definition spells enum nl80211_he_gi.
Synchronize them to the latter.

Cc: Martin Liska <mliska@suse.cz>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: ath11k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221031114341.10377-1-jirislaby@kernel.org

qmi_msg_handler is required to be null terminated by QMI module.
There might be a case where a handler for a msg id is not present in the
handlers array which can lead to infinite loop while searching the handler
and therefore out of bound access in qmi_invoke_handler().
Hence update the initialization in qmi_msg_handler data structure.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Rahul Bhattacharjee <quic_rbhattac@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221021090126.28626-1-quic_rbhattac@quicinc.com

Variable sent is just being incremented and it's never used
anywhere else. The variable and the increment are redundant so
remove it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221024153954.2168503-1-colin.i.king@gmail.com

ath.git patches for v6.2. Major changes:

ath11k

* support configuring channel dwell time during scan

In the event of a Tx hang it can be useful to read a variety of hardware
registers to capture some state about why the transmit queue got stuck.

Extend the ETHTOOL_GREGS dump provided by the ice driver with several CSR
registers that provide such relevant information regarding the hardware Tx
state. This enables capturing relevant data to enable debugging such a Tx
hang.
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Link: https://lore.kernel.org/r/20221027104239.1691549-1-jacob.e.keller@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Russell King says:

====================
Clean up SFP register definitions

This two-part patch series cleans up the SFP register definitions by
1. converting them from hex to decimal, as all the definitions in the
   documents use decimal, this makes it easier to cross-reference.
2. moving the bit definitions for each register along side their
   register address definition
====================

Link: https://lore.kernel.org/r/Y1qFvaDlLVM1fHdG@shell.armlinux.org.ukSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Just as we do for the A2h enum, arrange the A0h enum to have the
field definitions next to their corresponding register index.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The register indexes in the standards are in decimal rather than hex,
so lets specify them in decimal in the header file so we can easily
cross-reference without converting between hex and decimal.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Russell King says:

====================
net: mtk_eth_soc: improve PCS implementation

As a result of invesigations from Frank Wunderlich, we know a lot more
about the Mediatek "SGMII" PCS block, and can implement the PCS support
correctly. This series achieves that, and Frank has tested the final
result and reports that it works for him. The series could do with
further testing by others, but I suspect that is unlikely to happen
until it is merged based on past performances with this driver.

Briefly, the patches in order:

1. Add a new helper to get the link timer duration in nanoseconds
2. Add definitions for the newly discovered registers and updates to
   bit definitions, including bitmasks for the BMCR, BMSR and two
   advertisement registers.
3. Remove unnecessary/unused error handling (functions always returning
   zero.)
4. Adding the missing pcs_get_state() implementation.
5. Converting the code to use regmap_update_bits() rather than
   open-coding read-modify-write sequences.
6. Adding out-of-band speed and duplex forcing for all non-inband modes
   not just the 802.3z link modes the code currently does.
7. Moving the release of the PHY power down to the main pcs_config()
   function.
8. Moving the interface speed selection to the main pcs_config()
   function.
9. Adding advertisement programming.
10. Adding correct link timer programming using the new helper in the
    first patch.
11. Adding support for 802.3z negotiation.

There is one remaining issue - when configuring the PCS for in-band,
for some reason the AN restart bit is always set. This should not be
necessary, but requires further investigation with the hardware to
find out whether it is really necessary. I suspect this was a work
around for a previous poor implementation.
====================

Link: https://lore.kernel.org/r/Y1qDMw+DJLAJHT40@shell.armlinux.org.ukSigned-off-by: Jakub Kicinski <kuba@kernel.org>

As a result of help from Frank Wunderlich to investigate and test, we
now know how to program this PCS for in-band 802.3z negotiation. Add
support for this by moving the contents of the two functions into the
common mtk_pcs_config() function and adding the register settings for
802.3z negotiation.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Program the link timer appropriately for the interface mode being
used, using the newly introduced phylink helper that provides the
nanosecond link timer interval.

The intervals are 1.6ms for SGMII based protocols and 10ms for
802.3z based protocols.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Program the advertisement into the mtk PCS block.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Move the selection of the underlying interface speed to the pcs_config
function, so we always program the interface speed.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The PHY power up is common to both configuration paths, so move it into
the parent function. We need to do this for all serdes modes.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add support for forcing the link speed and duplex setting in the
pcs_link_up() method for out of band modes, which will be useful when
we finish converting the pcs_config() method. Until then, we still have
to force duplex for 802.3z modes to work correctly.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mtk_sgmii does a lot of read-modify-write operations, for which there
is a specific regmap function. Use this function instead of open-coding
the operations.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add a pcs_get_state() implementation which uses the advertisements
to compute the resulting link modes, and BMSR contents to determine
negotiation and link status.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The functions called by the pcs_config() method always return zero, so
there is no point trying to handle an error from these functions. Make
these functions void, eliminate the "err" variable and simply return
zero from the pcs_config() function itself.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

As a result of help from Frank Wunderlich to investigate and test, we
know a bit more about the PCS on the Mediatek platforms. Update the
definitions from this investigation.

This PCS appears similar, but not identical to the Lynx PCS.

Although not included in this patch, but for future reference, the PHY
ID registers at offset 4 read as 0x4d544950 'MTIP'.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add a helper to convert the PHY interface mode to the required link
timer setting as stated by the appropriate standard. Inappropriate
interface modes return an error.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Sebastian Andrzej Siewior says:

====================
net: Remove the obsolte u64_stats_fetch_*_irq()

This is the removal of u64_stats_fetch_*_irq() users in networking. The
prerequisites are part of v6.1-rc1.

The spi and bpf bits are not part of the series and have been routed
directly.
====================

Link: https://lore.kernel.org/r/20221026132215.696950-1-bigeasy@linutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Now that the 32bit UP oddity is gone and 32bit uses always a sequence
count, there is no need for the fetch_irq() variants anymore.

Convert to the regular interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Now that the 32bit UP oddity is gone and 32bit uses always a sequence
count, there is no need for the fetch_irq() variants anymore.

Convert to the regular interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

====================
pull-request: wireless-next-2022-10-28

First set of patches v6.2. mac80211 refactoring continues for Wi-Fi 7.
All mac80211 driver are now converted to use internal TX queues, this
might cause some regressions so we wanted to do this early in the
cycle.

Note: wireless tree was merged[1] to wireless-next to avoid some
conflicts with mac80211 patches between the trees. Unfortunately there
are still two smaller conflicts in net/mac80211/util.c which Stephen
also reported[2]. In the first conflict initialise scratch_len to
"params->scratch_len ?: 3 * params->len" (note number 3, not 2!) and
in the second conflict take the version which uses elems->scratch_pos.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next.git/commit/?id=dfd2d876b3fda1790bc0239ba4c6967e25d16e91
[2] https://lore.kernel.org/all/20221020032340.5cf101c0@canb.auug.org.au/

mac80211
 - preparation for Wi-Fi 7 Multi-Link Operation (MLO) continues
 - add API to show the link STAs in debugfs
 - all mac80211 drivers are now using mac80211 internal TX queues (iTXQs)

rtw89
 - support 8852BE

rtl8xxxu
 - support RTL8188FU

brmfmac
 - support two station interfaces concurrently

bcma
 - support SPROM rev 11
====================

Link: https://lore.kernel.org/r/20221028132943.304ECC433B5@smtp.kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

During firmware recovery, the monitor interface is not
getting created in the driver and firmware since
the respective flags are not updated properly.

So after firmware recovery is successful, when monitor
interface is brought down manually, firmware assertion
is observed, since we are trying to bring down the
interface which is not yet created in the firmware.

Fix this by updating the monitor flags properly per
phy#, during firmware recovery.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221014155054.11471-1-quic_nmaran@quicinc.com

Because we enable the clock immediately after acquiring it in probe,
we can combine the 2 operations and use devm_clk_get_optional_enabled()
helper.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiawen Wu says:

====================
net: WangXun txgbe ethernet driver

This patch series adds support for WangXun 10 gigabit NIC, to initialize
hardware, set mac address, and register netdev.

Change log:
v6: address comments:
    Jakub Kicinski: check with scripts/kernel-doc
v5: address comments:
    Jakub Kicinski: clean build with W=1 C=1
v4: address comments:
    Andrew Lunn: https://lore.kernel.org/all/YzXROBtztWopeeaA@lunn.ch/
v3: address comments:
    Andrew Lunn: remove hw function ops, reorder functions, use BIT(n)
                 for register bit offset, move the same code of txgbe
                 and ngbe to libwx
v2: address comments:
    Andrew Lunn: https://lore.kernel.org/netdev/YvRhld5rD%2FxgITEg@lunn.ch/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add MAC address related operations, and register netdev.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reset and initialize the hardware by configuring the MAC layer.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Get PCI config space info, set LAN id and check flash status.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mubashir Adnan Qureshi says:

====================
net: Add PLB functionality to TCP

This patch series adds PLB (Protective Load Balancing) to TCP and hooks
it up to DCTCP. PLB is disabled by default and can be enabled using
relevant sysctls and support from underlying CC.

PLB (Protective Load Balancing) is a host based mechanism for load
balancing across switch links. It leverages congestion signals(e.g. ECN)
from transport layer to randomly change the path of the connection
experiencing congestion. PLB changes the path of the connection by
changing the outgoing IPv6 flow label for IPv6 connections (implemented
in Linux by calling sk_rethink_txhash()). Because of this implementation
mechanism, PLB can currently only work for IPv6 traffic. For more
information, see the SIGCOMM 2022 paper:
  https://doi.org/10.1145/3544216.3544226
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

rcv_wnd can be useful to diagnose TCP performance where receiver window
becomes the bottleneck. rehash reports the PLB and timeout triggered
rehash attempts by the TCP connection.
Signed-off-by: Mubashir Adnan Qureshi <mubashirq@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A u32 counter is added to tcp_sock for counting the number of PLB
triggered rehashes for a TCP connection. An SNMP counter is also
added to count overall PLB triggered rehash events for a host. These
counters are hooked up to PLB implementation for DCTCP.

TCP_NLA_REHASH is added to SCM_TIMESTAMPING_OPT_STATS that reports
the rehash attempts triggered due to PLB or timeouts. This gives
a historical view of sustained congestion or timeouts experienced
by the TCP connection.
Signed-off-by: Mubashir Adnan Qureshi <mubashirq@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>