When multiple channel contexts are active, an offchannel
request will not be handled immediately, but will be
queued to be handled later. But, currently, the channel definition
is not copied to the local offchannel state. This
breaks operation like scanning when MCC is active.

Fix this by storing the offchannel parameters properly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Reduces code duplication.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently, the interface count is maintained globally,
but this causes problems in RX filter calculation.
Make the interface count a per-channel-context variable
to fix this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Maintain the RX filter on a per-channel-context
basis and not globally. Not doing so was resulting
in incorrect filter calculation.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ATH9K_RX_FILTER_COMP_BAR is used to receive BAR
completion frames and is set if the current channel
is HT. When channel contexts are enabled, instead of using
the mac80211 helpers, check if the current channel
definition is HT.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since ath_startrecv() doesn't return an error value,
cleanup the callsites.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If multiple channel contexts are active, then the opmode
can be different in each context. Since the RX filter is
calculated in ath_startrecv() before switching to the
new opmode, the wrong filters are chosen.

Fix this by calling ath9k_calculate_summary_state() before
the RX module is started.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since CTWindow can be used for improving discoverability,
fill this field in the NoA Attribute properly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently, different units are used for handling
sc->offchannel.duration. In scan mode, it contains jiffies and in RoC
mode, milliseconds is used. This causes confusion since in
ath_chanctx_switch(), TU_TO_USEC is used to determine the offchannel
duration, resulting in incorrect values. Fix this by using jiffies in
both modes.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The start time field in the NoA attribute needs to be
updated based on the TSF timer when an absence notification
is sent by the P2P GO. When two channel contexts are active,
continuous, cyclic NoA is announced by setting the count value to 255,
but the start time is updated only once, for one beacon and
the same value is sent in all subsequent beacons, even
though the timestamp keeps moving.

Fix this by removing the check for 'periodic_noa_duration'
and assign the interface's start_time/duration values directly
when there is more than one active context.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If a station interface is already assigned to a context
and is active and a second interface of type AP is added,
then beaconing on the new interface has to be begin only
after the BSS_CHANGED_BEACON_ENABLED flag is sent by mac80211
to the driver.

But, since we issue ATH_CHANCTX_EVENT_ENABLE_MULTICHANNEL as soon
as a new channel context is added, a switch occurs almost immediately
before BSS_CHANGED_BEACON_ENABLED is received. When a HW reset
is done for the new context, beacons are enabled for the
interface since "enable_beacon" in the BSS config maintained
in mac80211 is true - but the driver hasn't been notified yet.
This causes a panic, since the beacon interval is zero for this
interface and ath9k_cmn_beacon_config_ap() doesn't have a safety check.

Fix this panic by checking if the beacon params has been cached
for this context and use the "enable_beacon" flag maintained
locally in the driver. Also, recalculate the summary data
after the beacon params have been cached when BSS_CHANGED_BEACON_ENABLED
is received.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If the current opmode is managed, the ATH_OP_BEACONS flag
needs to be set only when there is a primary station interface
and it is associated/active.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In channel context mode, when a new context is added,
mac80211 issues a bss_info_changed() notfication when
preparing the connection for the new interface/context.

But, this is done prior to the mgd_prepare_tx() call which
is where we switch to the new context. Since the current
context will be different when the earlier bss_info_changed()
is handled, the beacon information for the VIF is not
updated, but discarded since the rules for the current context
disallows it.

In the subsequent association process for the new context/vif,
this becomes a problem because the beacon parameters are invalid.
This causes problems with the TSF timer, causing large jumps.

To fix this, check if the beacon info is being updated for a
different context and if so, allow it without any checks since
we limit the max. interfaces to two anyway.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

On Northstar (ARM arch) we will use MTD subsystem to access NVRAM and
SPROM. To get access to flash device we need to register these cores
first.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This cleans code a bit and will us to register cores in other places as
well. The only difference with this patch is using "core_index" for
setting device name.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch makes halbtcoutsrc.{c,h} work with the new pieces of the driver.
Also included are some modifications to various header files.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: troy_tan@realsil.com.cn
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This code comes from the V062414 version of the drivers from Realtek.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: troy_tan@realsil.com.cn
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds the code needed for the new rtl8821ae driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: troy_tan@realsil.com.cn
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds the routines found in the V062814 Realtek version.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: troy_tan@realsil.com.cn
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds the routines needed to support BT coexistence with the
new rtl8192ee driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: troy_tan@realsil.com.cn
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: troy_tan@realsil.com.cn
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch is the first of a set to bring this driver up to the latest Realtek code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: troy_tan@realsil.com.cn
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is required to split SoC bus init into two phases. The later one
(which includes scanning) should be called when kalloc is available.

Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This change is important for SoC host. In future we will want to know
chip ID (needed for early MIPS boot) before doing cores scanning.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Packets that are supposed to be delivered via the peer device need to
be checked and sent to correct device. This requires that user has set
the routes properly so that the 6lowpan module can then figure out
the destination gateway and the correct Bluetooth device.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 3.17.x

The peer IPv6 address contained wrong U/L bit in the EUI-64 part.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 3.17.x

Use the default connection timeout value defined in l2cap.h because
the current timeout was too short and most of the time the connection
attempts timed out.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 3.17.x

Suspend could fail for some platforms because
btusb_suspend==> btusb_stop_traffic ==> usb_kill_anchored_urbs.

When btusb_bulk_complete returns before system suspend and resubmits
an URB, the system cannot enter suspend state.
Signed-off-by: Champion Chen <champion_chen@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

Whether through HCI with BR/EDR or SMP with LE when authentication fails
we should also notify any pending Pair Device mgmt command. This patch
updates the mgmt_auth_failed function to take the actual hci_conn object
and makes sure that any pending pairing command is notified and cleaned
up appropriately.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch fixes the following type of static analyzer warning (and
probably a real bug as well as the NULL check should be there for a
reason):

net/bluetooth/smp.c:1182 smp_conn_security() warn: variable dereferenced before check 'conn' (see line 1174)
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Replaced the use of a Variable Length Array In Struct (VLAIS) with a C99
compliant equivalent. This patch allocates the appropriate amount of memory
using an char array.

The new code can be compiled with both gcc and clang.

struct shash_desc contains a flexible array member member ctx declared with
CRYPTO_MINALIGN_ATTR, so sizeof(struct shash_desc) aligns the beginning
of the array declared after struct shash_desc with long long.

No trailing padding is required because it is not a struct type that can
be used in an array.

The CRYPTO_MINALIGN_ATTR is required so that desc is aligned with long long
as would be the case for a struct containing a member with
CRYPTO_MINALIGN_ATTR.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Signed-off-by: Mark Charlebois <charlebm@gmail.com>
Signed-off-by: Jan-Simon Möller <dl9pf@gmx.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

SMP defines quite clearly when certain PDUs are to be expected/allowed
and when not, but doesn't have any explicit request/response definition.
So far the code has relied on each PDU handler to behave correctly if
receiving PDUs at an unexpected moment, however this requires many
different checks and is prone to errors.

This patch introduces a generic way to keep track of allowed PDUs and
thereby reduces the responsibility & load on individual command
handlers. The tracking is implemented using a simple bit-mask where each
opcode maps to its own bit. If the bit is set the corresponding PDU is
allow and if the bit is not set the PDU is not allowed.

As a simple example, when we send the Pairing Request we'd set the bit
for Pairing Response, and when we receive the Pairing Response we'd
clear the bit for Pairing Response.

Since the disallowed PDU rejection is now done in a single central place
we need to be a bit careful of which action makes most sense to all
cases. Previously some, such as Security Request, have been simply
ignored whereas others have caused an explicit disconnect.

The only PDU rejection action that keeps good interoperability and can
be used for all the applicable use cases is to drop the data. This may
raise some concerns of us now being more lenient for misbehaving (and
potentially malicious) devices, but the policy of simply dropping data
has been a successful one for many years e.g. in L2CAP (where this is
the *only* policy for such cases - we never request disconnection in
l2cap_core.c because of bad data). Furthermore, we cannot prevent
connected devices from creating the SMP context (through a Security or
Pairing Request), and once the context exists looking up the
corresponding bit for the received opcode and deciding to reject it is
essentially an equally lightweight operation as the kind of rejection
that l2cap_core.c already successfully does.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When we're in the process of receiving keys in phase 3 of SMP we keep
track of which keys are still expected in the smp->remote_key_dist
variable. If we still have some key bits set we need to continue waiting
for more PDUs and not needlessly call smp_distribute_keys(). This patch
fixes two such cases in the smp_cmd_master_ident() and
smp_cmd_ident_addr_info() handler functions.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds a define for the allowed bits of the key distribution
mask so we don't have to have magic 0x07 constants throughout the code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Before the move the l2cap_chan the SMP context (smp_chan) didn't have
any kind of proper locking. The best there existed was the
HCI_CONN_LE_SMP_PEND flag which was used to enable mutual exclusion for
potential multiple creators of the SMP context.

Now that SMP has been converted to use the l2cap_chan infrastructure and
since the SMP context is directly mapped to a corresponding l2cap_chan
we get the SMP context locking essentially for free through the
l2cap_chan lock. For all callbacks that l2cap_core.c makes for each
channel implementation (smp.c in the case of SMP) the l2cap_chan lock is
held through l2cap_chan_lock(chan).

Since the calls from l2cap_core.c to smp.c are covered the only missing
piece to have the locking implemented properly is to ensure that the
lock is held for any other call path that may access the SMP context.
This means user responses through mgmt.c, requests to elevate the
security of a connection through hci_conn.c, as well as any deferred
work through workqueues.

This patch adds the necessary locking to all these other code paths that
try to access the SMP context. Since mutual exclusion for the l2cap_chan
access is now covered from all directions the patch also removes
unnecessary HCI_CONN_LE_SMP_PEND flag (once we've acquired the chan lock
we can simply check whether chan->smp is set to know if there's an SMP
context).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Now that the identity address update happens through its own deferred
work there's no need to have smp_distribute_keys anymore behind a second
deferred work. This patch removes this extra construction and makes the
code do direct calls to smp_distribute_keys() again.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The identity address update of all channels for an l2cap_conn needs to
take the lock for each channel, i.e. it's safest to do this by a
separate workqueue callback.

Previously this was partially solved by moving the entire SMP key
distribution behind a workqueue. However, if we want SMP context locking
to be correct and safe we should always use the l2cap_chan lock when
accessing it, meaning even smp_distribute_keys needs to take that lock
which would once again create a dead lock when updating the identity
address.

The simplest way to solve this is to have l2cap_conn manage the deferred
work which is what this patch does. A subsequent patch will remove the
now unnecessary SMP key distribution work struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When smp_resume_cb is called if we're not encrypted (i.e. the callback
wasn't called because the connection became encrypted) we shouldn't take
any action at all. This patch moves also the security_timer cancellation
behind this condition.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The SMP security timer used to be able to modify the SMP context state
but now days it simply calls hci_disconnect(). It is therefore
unnecessary to have extra sanity checks for the SMP context after
canceling the timer.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The "pending" L2CAP response value is not defined for LE CoC. This patch
adds a clarifying comment to the code so that the reader will not think
there is a bug in trying to use this value for LE CoC.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>