We have two new SIE exit codes dealing with instructions.
104 (0x68) for a secure instruction interception, on which the SIE needs
hypervisor action to complete the instruction. We can piggy-back on the
existing instruction handlers.

108 which is merely a notification and provides data for tracking and
management. For example this is used to tell the host about a new value
for the prefix register. As there will be several special case handlers
in later patches, we handle this in a separate function.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>

Since there is no interception for load control and load psw
instruction in the protected mode, we need a new way to get notified
whenever we can inject an IRQ right after the guest has just enabled
the possibility for receiving them.

The new interception codes solve that problem by providing a
notification for changes to IRQ enablement relevant bits in CRs 0, 6
and 14, as well a the machine check mask bit in the PSW.

No special handling is needed for these interception codes, the KVM
pre-run code will consult all necessary CRs and PSW bits and inject
IRQs the guest is enabled for.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>

Before we destroy the secure configuration, we better make all
pages accessible again. This also happens during reboot, where we reboot
into a non-secure guest that then can go again into secure mode. As
this "new" secure guest will have a new ID we cannot reuse the old page
state.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>

KSM will not work on secure pages, because when the kernel reads a
secure page, it will be encrypted and hence no two pages will look the
same.

Let's mark the guest pages as unmergeable when we transition to secure
mode.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>

This contains 3 main changes:
1. changes in SIE control block handling for secure guests
2. helper functions for create/destroy/unpack secure guests
3. KVM_S390_PV_COMMAND ioctl to allow userspace dealing with secure
machines
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>

This adds two new helper functions for doing UV CALLs.

The first variant handles UV CALLs that might have longer busy
conditions or just need longer when doing partial completion. We should
schedule when necessary.

The second variant handles UV CALLs that only need the handle but have
no payload (e.g. destroying a VM). We can provide a simple wrapper for
those.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>

Let's have some debug traces which stay around for longer than the
guest.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>

The adapter interrupt page containing the indicator bits is currently
pinned. That means that a guest with many devices can pin a lot of
memory pages in the host. This also complicates the reference tracking
which is needed for memory management handling of protected virtual
machines. It might also have some strange side effects for madvise
MADV_DONTNEED and other things.

We can simply try to get the userspace page set the bits and free the
page. By storing the userspace address in the irq routing entry instead
of the guest address we can actually avoid many lookups and list walks
so that this variant is very likely not slower.

If userspace messes around with the memory slots the worst thing that
can happen is that we write to some other memory within that process.
As we get the the page with FOLL_WRITE this can also not be used to
write to shared read-only pages.
Signed-off-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[borntraeger@de.ibm.com: patch simplification]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>

s390 base parts (non kvm) for protvirt

That information, e.g. the maximum number of guests or installed
Ultravisor facilities, is interesting for QEMU, Libvirt and
administrators.

Let's provide an easily parsable API to get that information.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>

Add exceptions handlers performing transparent transition of non-secure
pages to secure (import) upon guest access and secure pages to
non-secure (export) upon hypervisor access.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
[frankja@linux.ibm.com: adding checks for failures]
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
[imbrenda@linux.ibm.com:  adding a check for gmap fault]
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>

This provides the basic ultravisor calls and page table handling to cope
with secure guests:
- provide arch_make_page_accessible
- make pages accessible after unmapping of secure guests
- provide the ultravisor commands convert to/from secure
- provide the ultravisor commands pin/unpin shared
- provide callbacks to make pages secure (inacccessible)
 - we check for the expected pin count to only make pages secure if the
   host is not accessing them
 - we fence hugetlbfs for secure pages
- add missing radix-tree include into gmap.h

The basic idea is that a page can have 3 states: secure, normal or
shared. The hypervisor can call into a firmware function called
ultravisor that allows to change the state of a page: convert from/to
secure. The convert from secure will encrypt the page and make it
available to the host and host I/O. The convert to secure will remove
the host capability to access this page.
The design is that on convert to secure we will wait until writeback and
page refs are indicating no host usage. At the same time the convert
from secure (export to host) will be called in common code when the
refcount or the writeback bit is already set. This avoids races between
convert from and to secure.

Then there is also the concept of shared pages. Those are kind of secure
where the host can still access those pages. We need to be notified when
the guest "unshares" such a page, basically doing a convert to secure by
then. There is a call "pin shared page" that we use instead of convert
from secure when possible.

We do use PG_arch_1 as an optimization to minimize the convert from
secure/pin shared.

Several comments have been added in the code to explain the logic in
the relevant places.
Co-developed-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Signed-off-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>

Before being able to host protected virtual machines, donate some of
the memory to the ultravisor. Besides that the ultravisor might impose
addressing limitations for memory used to back protected VM storage. Treat
that limit as protected virtualization host's virtual memory limit.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>

Add "prot_virt" command line option which controls if the kernel
protected VMs support is enabled at early boot time. This has to be
done early, because it needs large amounts of memory and will disable
some features like STP time sync for the lpar.

Extend ultravisor info definitions and expose it via uv_info struct
filled in during startup.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>

Pull IPMI update from Corey Minyard:
 "Minor bug fixes for IPMI

  I know this is late; I've been travelling and, well, I've been
  distracted.

  This is just a few bug fixes and adding i2c support to the IPMB
  driver, which is something I wanted from the beginning for it"

* tag 'for-linus-5.6-1' of https://github.com/cminyard/linux-ipmi:
  drivers: ipmi: fix off-by-one bounds check that leads to a out-of-bounds write
  ipmi:ssif: Handle a possible NULL pointer reference
  drivers: ipmi: Modify max length of IPMB packet
  drivers: ipmi: Support raw i2c packet in IPMB

Pull KVM fixes from Paolo Bonzini:
 "Bugfixes and improvements to selftests.

  On top of this, Mauro converted the KVM documentation to rst format,
  which was very welcome"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (44 commits)
  docs: virt: guest-halt-polling.txt convert to ReST
  docs: kvm: review-checklist.txt: rename to ReST
  docs: kvm: Convert timekeeping.txt to ReST format
  docs: kvm: Convert s390-diag.txt to ReST format
  docs: kvm: Convert ppc-pv.txt to ReST format
  docs: kvm: Convert nested-vmx.txt to ReST format
  docs: kvm: Convert mmu.txt to ReST format
  docs: kvm: Convert locking.txt to ReST format
  docs: kvm: Convert hypercalls.txt to ReST format
  docs: kvm: arm/psci.txt: convert to ReST
  docs: kvm: convert arm/hyp-abi.txt to ReST
  docs: kvm: Convert api.txt to ReST format
  docs: kvm: convert devices/xive.txt to ReST
  docs: kvm: convert devices/xics.txt to ReST
  docs: kvm: convert devices/vm.txt to ReST
  docs: kvm: convert devices/vfio.txt to ReST
  docs: kvm: convert devices/vcpu.txt to ReST
  docs: kvm: convert devices/s390_flic.txt to ReST
  docs: kvm: convert devices/mpic.txt to ReST
  docs: kvm: convert devices/arm-vgit.txt to ReST
  ...

Pull EDAC fixes from Borislav Petkov:
 "Two fixes for use-after-free and memory leaking in the EDAC core, by
  Robert Richter.

  Debug options like DEBUG_TEST_DRIVER_REMOVE, KASAN and DEBUG_KMEMLEAK
  unearthed issues with the lifespan of memory allocated by the EDAC
  memory controller descriptor due to misdesigned memory freeing, done
  partially by the EDAC core *and* the driver core, which is problematic
  to say the least.

  These two are minimal fixes to take care of stable - a proper rework
  is following which cleans up that mess properly"

* tag 'edac_urgent_for_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
  EDAC/sysfs: Remove csrow objects on errors
  EDAC/mc: Fix use-after-free and memleaks during device removal

Pull block fixes from Jens Axboe:
 "Not a lot here, which is great, basically just three small bcache
  fixes from Coly, and four NVMe fixes via Keith"

* tag 'block-5.6-2020-02-16' of git://git.kernel.dk/linux-block:
  nvme: fix the parameter order for nvme_get_log in nvme_get_fw_slot_info
  nvme/pci: move cqe check after device shutdown
  nvme: prevent warning triggered by nvme_stop_keep_alive
  nvme/tcp: fix bug on double requeue when send fails
  bcache: remove macro nr_to_fifo_front()
  bcache: Revert "bcache: shrink btree node cache after bch_btree_check()"
  bcache: ignore pending signals when creating gc and allocator thread

Pull btrfs fixes from David Sterba:
 "Two races fixed, memory leak fix, sysfs directory fixup and two new
  log messages:

   - two fixed race conditions: extent map merging and truncate vs
     fiemap

   - create the right sysfs directory with device information and move
     the individual device dirs under it

   - print messages when the tree-log is replayed at mount time or
     cannot be replayed on remount"

* tag 'for-5.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: sysfs, move device id directories to UUID/devinfo
  btrfs: sysfs, add UUID/devinfo kobject
  Btrfs: fix race between shrinking truncate and fiemap
  btrfs: log message when rw remount is attempted with unclean tree-log
  btrfs: print message when tree-log replay starts
  Btrfs: fix race between using extent maps and merging them
  btrfs: ref-verify: fix memory leaks

Pull cifs fixes from Steve French:
 "Four small CIFS/SMB3 fixes. One (the EA overflow fix) for stable"

* tag '5.6-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: make sure we do not overflow the max EA buffer size
  cifs: enable change notification for SMB2.1 dialect
  cifs: Fix mode output in debugging statements
  cifs: fix mount option display for sec=krb5i

Pull ext4 fixes from Ted Ts'o:
 "Miscellaneous ext4 bug fixes (all stable fodder)"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: improve explanation of a mount failure caused by a misconfigured kernel
  jbd2: do not clear the BH_Mapped flag when forgetting a metadata buffer
  jbd2: move the clearing of b_modified flag to the journal_unmap_buffer()
  ext4: add cond_resched() to ext4_protect_reserved_inode
  ext4: fix checksum errors with indexed dirs
  ext4: fix support for inode sizes > 1024 bytes
  ext4: simplify checking quota limits in ext4_statfs()
  ext4: don't assume that mmp_nodename/bdevname have NUL

Pull input updates from Dmitry Torokhov:

 - a few drivers have been updated to use flexible-array syntax instead
   of GCC extension

 - ili210x touchscreen driver now supports the 2120 protocol flavor

 - a couple more of Synaptics devices have been switched over to RMI4

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: cyapa - replace zero-length array with flexible-array member
  Input: tca6416-keypad - replace zero-length array with flexible-array member
  Input: gpio_keys_polled - replace zero-length array with flexible-array member
  Input: synaptics - remove the LEN0049 dmi id from topbuttonpad list
  Input: synaptics - enable SMBus on ThinkPad L470
  Input: synaptics - switch T470s to RMI4 by default
  Input: gpio_keys - replace zero-length array with flexible-array member
  Input: goldfish_events - replace zero-length array with flexible-array member
  Input: psmouse - switch to using i2c_new_scanned_device()
  Input: ili210x - add ili2120 support
  Input: ili210x - fix return value of is_visible function

Pull rdma fixes from Jason Gunthorpe:
 "Not too much going on here, though there are about four fixes related
  to stuff merged during the last merge window.

  We also see the return of a syzkaller instance with access to RDMA
  devices, and a few bugs detected by that squished.

   - Fix three crashers and a memory memory leak for HFI1

   - Several bugs found by syzkaller

   - A bug fix for the recent QP counters feature on older mlx5 HW

   - Locking inversion in cxgb4

   - Unnecessary WARN_ON in siw

   - A umad crasher regression during unload, from a bug fix for
     something else

   - Bugs introduced in the merge window:
       - Missed list_del in uverbs file rework, core and mlx5 devx
       - Unexpected integer math truncation in the mlx5 VAR patches
       - Compilation bug fix for the VAR patches on 32 bit"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  IB/mlx5: Use div64_u64 for num_var_hw_entries calculation
  RDMA/core: Fix protection fault in get_pkey_idx_qp_list
  RDMA/rxe: Fix soft lockup problem due to using tasklets in softirq
  RDMA/mlx5: Prevent overflow in mmap offset calculations
  IB/umad: Fix kernel crash while unloading ib_umad
  RDMA/mlx5: Fix async events cleanup flows
  RDMA/core: Add missing list deletion on freeing event queue
  RDMA/siw: Remove unwanted WARN_ON in siw_cm_llp_data_ready()
  RDMA/iw_cxgb4: initiate CLOSE when entering TERM
  IB/mlx5: Return failure when rts2rts_qp_counters_set_id is not supported
  RDMA/core: Fix invalid memory access in spec_filter_size
  IB/rdmavt: Reset all QPs when the device is shut down
  IB/hfi1: Close window for pq and request coliding
  IB/hfi1: Acquire lock to release TID entries when user file is closed
  RDMA/hfi1: Fix memory leak in _dev_comp_vect_mappings_create

Pull ARM SoC fixes from Olof Johansson:
 "A handful of fixes that have come in since the merge window:

   - Fix of PCI interrupt map on arm64 fast model (SW emulator)

   - Fixlet for sound on ST platforms and a small cleanup of deprecated
     DT properties

   - A stack buffer overflow fix for moxtet

   - Fuse driver build fix for Tegra194

   - A few config updates to turn on new drivers merged this cycle"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  bus: moxtet: fix potential stack buffer overflow
  soc/tegra: fuse: Fix build with Tegra194 configuration
  ARM: dts: sti: fixup sound frame-inversion for stihxxx-b2120.dtsi
  ARM: dts: sti: Remove deprecated snps PHY properties for stih410-b2260
  arm64: defconfig: Enable DRM_SUN6I_DSI
  arm64: defconfig: Enable CONFIG_SUN8I_THERMAL
  ARM: sunxi: Enable CONFIG_SUN8I_THERMAL
  arm64: defconfig: Set bcm2835-dma as built-in
  ARM: configs: Cleanup old Kconfig options
  ARM: npcm: Bring back GPIOLIB support
  arm64: dts: fast models: Fix FVP PCI interrupt-map property

Pull s390 updates from Vasily Gorbik:

 - Enable paes-s390 cipher selftests in testmgr (acked-by Herbert Xu).

 - Fix protected key length update in PKEY_SEC2PROTK ioctl and increase
   card/queue requests counter to 64-bit in crypto code.

 - Fix clang warning in get_tod_clock.

 - Fix ultravisor info length extensions handling.

 - Fix style of SPDX License Identifier in vfio-ccw.

 - Avoid unnecessary GFP_ATOMIC and simplify ACK tracking in qdio.

* tag 's390-5.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  crypto/testmgr: enable selftests for paes-s390 ciphers
  s390/time: Fix clk type in get_tod_clock
  s390/uv: Fix handling of length extensions
  s390/qdio: don't allocate *aob array with GFP_ATOMIC
  s390/qdio: simplify ACK tracking
  s390/zcrypt: fix card and queue total counter wrap
  s390/pkey: fix missing length of protected key on return
  vfio-ccw: Use the correct style for SPDX License Identifier

Merge tag 'hwmon-for-v5.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:
 "Fix compatible string typos in the xdpe12284 driver, and a wrong bit
  value in the ltc2978 driver"

* tag 'hwmon-for-v5.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (pmbus/xdpe12284) fix typo in compatible strings
  hwmon: (pmbus/ltc2978) Fix PMBus polling of MFR_COMMON definitions.

Pull scheduler fixes from Ingo Molnar:
 "Misc fixes all over the place:

   - Fix NUMA over-balancing between lightly loaded nodes. This is
     fallout of the big load-balancer rewrite.

   - Fix the NOHZ remote loadavg update logic, which fixes anomalies
     like reported 150 loadavg on mostly idle CPUs.

   - Fix XFS performance/scalability

   - Fix throttled groups unbound task-execution bug

   - Fix PSI procfs boundary condition

   - Fix the cpu.uclamp.{min,max} cgroup configuration write checks

   - Fix DocBook annotations

   - Fix RCU annotations

   - Fix overly CPU-intensive housekeeper CPU logic loop on large CPU
     counts"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/fair: Fix kernel-doc warning in attach_entity_load_avg()
  sched/core: Annotate curr pointer in rq with __rcu
  sched/psi: Fix OOB write when writing 0 bytes to PSI files
  sched/fair: Allow a per-CPU kthread waking a task to stack on the same CPU, to fix XFS performance regression
  sched/fair: Prevent unlimited runtime on throttled group
  sched/nohz: Optimize get_nohz_timer_target()
  sched/uclamp: Reject negative values in cpu_uclamp_write()
  sched/fair: Allow a small load imbalance between low utilisation SD_NUMA domains
  timers/nohz: Update NOHZ load in remote tick
  sched/core: Don't skip remote tick for idle CPUs

Pull perf fixes from Ingo Molnar:
 "Fixes and HW enablement patches:

   - Tooling fixes, most of which are tooling header synchronization
     with v5.6 changes

   - Fix kprobes fallout on ARM

   - Add Intel Elkhart Lake support and extend Tremont support, these
     are relatively simple and should only affect those models

   - Fix the AMD family 17h generic event table"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (30 commits)
  perf llvm: Fix script used to obtain kernel make directives to work with new kbuild
  tools headers kvm: Sync linux/kvm.h with the kernel sources
  tools headers kvm: Sync kvm headers with the kernel sources
  tools arch x86: Sync asm/cpufeatures.h with the kernel sources
  tools headers x86: Sync disabled-features.h
  tools include UAPI: Sync sound/asound.h copy
  tools headers UAPI: Sync asm-generic/mman-common.h with the kernel
  perf tools: Add arm64 version of get_cpuid()
  tools headers UAPI: Sync drm/i915_drm.h with the kernel sources
  tools headers uapi: Sync linux/fscrypt.h with the kernel sources
  tools headers UAPI: Sync sched.h with the kernel
  perf trace: Resolve prctl's 'option' arg strings to numbers
  perf beauty prctl: Export the 'options' strarray
  tools headers UAPI: Sync prctl.h with the kernel sources
  tools headers UAPI: Sync copy of arm64's asm/unistd.h with the kernel sources
  perf maps: Move kmap::kmaps setup to maps__insert()
  perf maps: Fix map__clone() for struct kmap
  perf maps: Mark ksymbol DSOs with kernel type
  perf maps: Mark module DSOs with kernel type
  tools include UAPI: Sync x86's syscalls_64.tbl, generic unistd.h and fcntl.h to pick up openat2 and pidfd_getfd
  ...

The input_read function declares the size of the hex array relative to
sizeof(buf), but buf is a pointer argument of the function. The hex
array is meant to contain hexadecimal representation of the bin array.

Link: https://lore.kernel.org/r/20200215142130.22743-1-marek.behun@nic.cz
Fixes: 5bc7f990 ("bus: Add support for Moxtet bus")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reported-by: sohu0106 <sohu0106@126.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

If CONFIG_QFMT_V2 is not enabled, but CONFIG_QUOTA is enabled, when a
user tries to mount a file system with the quota or project quota
enabled, the kernel will emit a very confusing messsage:

    EXT4-fs warning (device vdc): ext4_enable_quotas:5914: Failed to enable quota tracking (type=0, err=-3). Please run e2fsck to fix.
    EXT4-fs (vdc): mount failed

We will now report an explanatory message indicating which kernel
configuration options have to be enabled, to avoid customer/sysadmin
confusion.

Link: https://lore.kernel.org/r/20200215012738.565735-1-tytso@mit.edu
Google-Bug-Id: 149093531
Fixes: 7c319d32 ("ext4: make quota as first class supported feature")
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org

Merge tag 'perf-urgent-for-mingo-5.6-20200214' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent

Pull perf/urgent fixes from Arnaldo Carvalho de Melo:

BPF:

  Arnaldo Carvalho de Melo:

  - Fix script used to obtain kernel make directives to work with new kbuild
    used for building BPF programs.

maps:

  Jiri Olsa:

  - Fixup kmap->kmaps backpointer in kernel maps.

arm64:

  John Garry:

  - Add arm64 version of get_cpuid() to get proper, arm64 specific output from
    'perf list' and other tools.

perf top:

  Kim Phillips:

  - Update kernel idle symbols so that output in AMD systems is in line with
    other systems.

perf stat:

  Kim Phillips:

  - Don't report a null stalled cycles per insn metric.

tools headers:

  Arnaldo Carvalho de Melo:

  - Sync tools/ headers with the kernel sources to get things like syscall
    numbers and new arguments so that 'perf trace' can decode and use them in
    tracepoint filters, e.g. prctl's new PR_{G,S}ET_IO_FLUSHER options.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200214172132.GA28389@embeddedorSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200214172022.GA27490@embeddedorSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200214171907.GA26588@embeddedorSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Pull NFS client bugfixes from Anna Schumaker:
 "The only stable fix this time is the DMA scatter-gather list bug fixed
  by Chuck.

  The rest fix up races and refcounting issues that have been found
  during testing.

  Stable fix:
   - fix DMA scatter-gather list mapping imbalance

  The rest:
   - fix directory verifier races
   - fix races between open and dentry revalidation
   - fix revalidation of dentries with delegations
   - fix "cachethis" setting for writes
   - fix delegation and delegation cred pinning"

* tag 'nfs-for-5.6-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
  NFSv4: Ensure the delegation cred is pinned when we call delegreturn
  NFSv4: Ensure the delegation is pinned in nfs_do_return_delegation()
  NFSv4.1 make cachethis=no for writes
  xprtrdma: Fix DMA scatter-gather list mapping imbalance
  NFSv4: Fix revalidation of dentries with delegations
  NFSv4: Fix races between open and dentry revalidation
  NFS: Fix up directory verifier races

Pull ceph fixes from Ilya Dryomov:

 - make O_DIRECT | O_APPEND combination work better

 - redo the server path canonicalization patch that went into -rc1

 - fix the 'noacl' mount option that got broken by the conversion to the
   new mount API in 5.5

* tag 'ceph-for-5.6-rc2' of https://github.com/ceph/ceph-client:
  ceph: noacl mount option is effectively ignored
  ceph: canonicalize server path in place
  ceph: do not execute direct write in parallel if O_APPEND is specified

Pull io_uring fixes from Jens Axboe:
 "Here's a set of fixes for io_uring:

   - Various fixes with cleanups from Pavel, fixing corner cases where
     we're not correctly dealing with iovec cleanup.

   - Clarify that statx/openat/openat2 don't accept fixed files

   - Buffered raw device write EOPTNOTSUPP fix

   - Ensure async workers grab current->fs

   - A few task exit fixes with pending requests that grab the file
     table

   - send/recvmsg async load fix

   - io-wq offline node setup fix

   - CQ overflow flush in poll"

* tag 'io_uring-5.6-2020-02-14' of git://git.kernel.dk/linux-block: (21 commits)
  io_uring: prune request from overflow list on flush
  io-wq: don't call kXalloc_node() with non-online node
  io_uring: retain sockaddr_storage across send/recvmsg async punt
  io_uring: cancel pending async work if task exits
  io-wq: add io_wq_cancel_pid() to cancel based on a specific pid
  io-wq: make io_wqe_cancel_work() take a match handler
  io_uring: fix openat/statx's filename leak
  io_uring: fix double prep iovec leak
  io_uring: fix async close() with f_op->flush()
  io_uring: allow AT_FDCWD for non-file openat/openat2/statx
  io_uring: grab ->fs as part of async preparation
  io-wq: add support for inheriting ->fs
  io_uring: retry raw bdev writes if we hit -EOPNOTSUPP
  io_uring: add cleanup for openat()/statx()
  io_uring: fix iovec leaks
  io_uring: remove unused struct io_async_open
  io_uring: flush overflowed CQ events in the io_uring_poll()
  io_uring: statx/openat/openat2 don't support fixed files
  io_uring: fix deferred req iovec leak
  io_uring: fix 1-bit bitfields to be unsigned
  ...

Pull networking fixes from David Miller:

 1) Fix interrupt name truncation in mv88e6xxx dsa driver, from Andrew
    Lunn.

 2) Process generic XDP even if SKB is cloned, from Toke Høiland-Jørgensen.

 3) Fix leak of kernel memory to userspace in smc, from Eric Dumazet.

 4) Add some missing netlink attribute validation to matchall and
    flower, from Davide Caratti.

 5) Send icmp responses properly when NAT has been applied to the frame
    before we get to the tunnel emitting the icmp, from Jason Donenfeld.

 6) Make sure there is enough SKB headroom when adding dsa tags for qca
    and ar9331. From Per Forlin.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (62 commits)
  netdevice.h: fix all kernel-doc and Sphinx warnings
  net: dsa: tag_ar9331: Make sure there is headroom for tag
  net: dsa: tag_qca: Make sure there is headroom for tag
  net, ip6_tunnel: enhance tunnel locate with link check
  net/smc: no peer ID in CLC decline for SMCD
  net/smc: transfer fasync_list in case of fallback
  net: hns3: fix a copying IPv6 address error in hclge_fd_get_flow_tuples()
  net: hns3: fix VF bandwidth does not take effect in some case
  net: hns3: add management table after IMP reset
  mac80211: fix wrong 160/80+80 MHz setting
  cfg80211: add missing policy for NL80211_ATTR_STATUS_CODE
  xfrm: interface: use icmp_ndo_send helper
  wireguard: device: use icmp_ndo_send helper
  sunvnet: use icmp_ndo_send helper
  gtp: use icmp_ndo_send helper
  icmp: introduce helper for nat'd source address in network device context
  net/sched: flower: add missing validation of TCA_FLOWER_FLAGS
  net/sched: matchall: add missing validation of TCA_MATCHALL_FLAGS
  net/flow_dissector: remove unexist field description
  page_pool: refill page when alloc.count of pool is zero
  ...

Pull power management fixes from Rafael Wysocki:
 "Fix three issues related to the handling of wakeup events signaled
  through the ACPI SCI while suspended to idle (Rafael Wysocki) and
  unexport an internal cpufreq variable (Yangtao Li)"

* tag 'pm-5.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: PM: s2idle: Prevent spurious SCIs from waking up the system
  ACPICA: Introduce acpi_any_gpe_status_set()
  ACPI: PM: s2idle: Avoid possible race related to the EC GPE
  ACPI: EC: Fix flushing of pending work
  cpufreq: Make cpufreq_global_kobject static