Merge tag 'renesas-arm64-dt-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/late

Pull "Renesas ARM64 Based SoC DT Updates for v4.9" from Simon Horman:

Clean up:
* Remove unnecessary cap-mmc-highspeed property from SDHI nodes on r8a7795 SoC
* Add SoC-specific compatible property to audio-dmac nodes on r8a7795 SoC

New Board:
* Add r8a7794/h3ulcb board

Enablement:
* Add PFC and GPIO to r8a7796 SoC
* Enable DU and USB 2.0 on r8a7795/salvator-x board
* Add VTP, FCPV, FCPF and FDP1 to r8a7795 SoC
* Set maximum frequency for SDHI clocks on r8a7795 SoC

* tag 'renesas-arm64-dt-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (43 commits)
  arm64: dts: r8a7796: Add GPIO device nodes
  arm64: dts: r8a7796: salvator-x: add serial console pins
  arm64: dts: r8a7796: Add pinctrl device node
  arm64: dts: r8a7795: salvator-x: Configure pins for the DU RGB output
  arm64: dts: h3ulcb: enable GPIO leds
  arm64: dts: h3ulcb: Sound SSI support
  arm64: dts: h3ulcb: enable SDHI0
  arm64: dts: h3ulcb: enable GPIO keys
  arm64: dts: r8a7795: remove unnecessary cap-mmc-highspeed property
  arm64: dts: h3ulcb: enable USB2.0 Host channel 1
  arm64: dts: h3ulcb: enable USB2 PHY of channel 1
  arm64: dts: h3ulcb: enable WDT
  arm64: dts: h3ulcb: enable EXTALR clk
  arm64: dts: h3ulcb: enable I2C2
  arm64: dts: h3ulcb: enable EthernetAVB
  arm64: dts: h3ulcb: enable SCIF clk and pins
  arm64: dts: h3ulcb: initial device tree
  arm64: dts: h3ulcb: add H3ULCB board DT bindings
  arm64: dts: r8a7795: Add SoC-specific compatible property to audio-dmac nodes
  arm64: dts: r8a7795: renesas: salvator-x: Enable DU
  ...

Merge tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/late

Pull "Amlogic 64-bit DT changes for v4.9" from Kevin Hilman:

- add watchdog, reset, IR remote, PWM
- add secure monitor and eFuse
- add always-on (AO) domain clock and reset

* tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM64: dts: amlogic: gxbb: Enable NVMEM
  documentation: Add nvmem bindings documentation
  ARM64: dts: amlogic: gxbb: Enable secure monitor
  documentation: Add secure monitor bindings documentation
  ARM64: dts: meson-gxbb: Add PWM pinctrl nodes
  ARM64: dts: meson-gxbb: Enable the the IR decoder on supported boards
  ARM64: dts: meson-gxbb: Add Infrared Remote Controller decoder
  dt-bindings: media: meson-ir: Add Meson8b and GXBB compatible strings
  ARM64: dts: amlogic: add the input pin for the IR remote
  ARM64: dts: meson-gxbb: Add GXBB AO Clock and Reset node
  clk: meson: Fix invalid use of sizeof in gxbb_aoclkc_probe()
  clk: meson: Add GXBB AO Clock and Reset controller driver
  dt-bindings: clock: reset: Add GXBB AO Clock and Reset Bindings
  ARM64: DTS: meson-gxbb: switch ethernet to real clock
  ARM64: dts: amlogic: meson-gxbb: Add watchdog node

Merge tag 'sunxi-dt-for-4.9-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/late

Merge "Allwinner DT changes for 4.9, take 2" from Maxime Ripard:

A second set of device tree changes, this time switching a few SoCs to the
new sunxi-ng clock framework. We also added the support for a new SoC
(NextThing GR8 and its evaluation board), and the support for the DRM
driver in the A33.

To maintain bisectability, while avoiding some un-trivial merge
conflicts, I had to merge the clk branch that I've sent a PR to Mike
and Stephen. This branch will of course be stable.

* tag 'sunxi-dt-for-4.9-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (53 commits)
  ARM: dts: gr8: Add support for the GR8 evaluation board
  ARM: dts: Add NextThing GR8 dtsi
  ARM: dts: sun8i: Move A23/A33 usbphy and usb_otg nodes to common dtsi
  ARM: sun8i: a23/a33: Add RGB666 pins
  ARM: sun8i: a33: Add display pipeline
  ARM: sun8i: Convert the A23 and A33 to the CCU
  ARM: dts: sun6i: switch A31/A31s to new CCU clock bindings
  clk: sunxi-ng: Add hardware dependency
  clk: sunxi-ng: Add A23 CCU
  clk: sunxi-ng: Add A33 CCU support
  clk: sunxi-ng: Add N-class clocks support
  clk: sunxi-ng: mux: Add mux table macro
  clk: sunxi-ng: div: Allow to set a maximum
  clk: sunxi-ng: div: Add kerneldoc for the _ccu_div structure
  clk: sunxi-ng: div: Add mux table macros
  devicetree: Add vendor prefix for FriendlyARM
  ARM: dts: sun8i: Add dts file for the NanoPi NEO SBC
  ARM: dts: sun8i-q8-common: Add support for SDIO wifi controllers
  ARM: dts: sun8i: Add dts file for the Orange Pi Plus2E SBC
  ARM: dts: sun8i: Orange Pi Plus dts is for the Plus and Plus 2
  ...

The GR8-EVB is a small board with an NextThing GR8, an Hynix MLC NAND,
an AXP209 PMIC, USB host and OTG, an SPDIF output and a connectors for CSI,
I2S and LCD.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The GR8 is an SoC made by Nextthing loosely based on the sun5i family.

Since it's not clear yet what we can factor out and merge with the A10s and
A13 support, let's keep it out of the sun5i.dtsi include tree. We will
figure out what can be shared when things settle down.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The usbphy and usb_otg nodes in the A23 and A33 dts files only differ
by compatible, and for the usbphy, the size of one of its register
regions.

Move all the common bits to the A23/A33 common dtsi file.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The LCD output needs to be muxed. Add the proper pinctrl node.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

Add all the needed blocks to the A33 DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

Now that we have support for the CCU driver in sunxi-ng, convert the A23
and A33 DTs to that driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

Now that we have a different clock representation, switch to it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The sunxi-ng clock driver is useless for other architectures.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add support for the clock unit found in the A23. Due to the similarities
with the A33, it also shares its clock IDs to allow sharing the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

This commit introduces the clocks found in the Allwinner A33 CCU.

Since this SoC is very similar to the A23, and we share a significant share
of the DTSI, the clock IDs that are going to be used will also be shared
with the A23, hence the name of the various header files.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

Add support for the class with a single factor, N, being a multiplier.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

Add a new macro to declare muxes based on a table and a gate.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

Some dividers might have a maximum value that is lower than the width of
the register.

Add a field to _ccu_div to handle those case properly. If the field is set
to 0, the code will assume that the maximum value is the maximum one that
can be used with the field register width.

Otherwise, we'll use whatever value has been set.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The internal _ccu_div structure is meant to be embedded into other
structures to combine the various dividers and to form the clock classes
support.

Start to document those structures by using kerneldoc.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add some macros to ease the declaration of clocks that are using them.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

Add GPIO device nodes to the DT of the r8a7796 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Adds pin control for SCIF2.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds pinctrl device node for R8A7796 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This supports GPIO leds on H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This supports SSI sound for H3ULCB board.
SSI DMA mode used. CS2000 used as AUDIO_CLK_B.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This supports SDHI0 on H3ULCB board SD card slot
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This supports GPIO keys on H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Remove cap-mmc-highspeed property from SDHI2 and SDHI3.

This property is unnecessary as the driver automatically sets
the highspeed capability. Furthermore its use is inconsistent with SDHI0
and SDHI1 which are also highspeed capable but do not have this property
present.

Found by inspection.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This supports USB2.0 Host channel 1 on H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This supports USB2 PHY channel #1 on H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This supports watchdog timer for H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This enables EXTALR clock that can be used for the watchdog.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This supports I2C2 bus on H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This supports Ethernet AVB on H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This enables the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the initial device tree for the R8A7795 SoC based H3ULCB low cost
board.

This commit supports the following peripherals:
- SCIF (console)
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add H3ULCB Device tree bindings Documentation, listing it as a supported
board.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The audio-dmac nodes used the generic compatible property only.
Add the SoC-specific one, to make it future proof.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Only the VGA output is supported for now.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the DU device to r8a7795.dtsi in a disabled state.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>