Implement the extended HE-MU info type decoding to show the HE-SIG-B
common contents in the HE-MU radiotap field.

The DW4 data is partially overwritten by the hardware in all cases, so
only the higher 16 bits can be used.  To be able to use it for the HE
SIG-B common data anyway, move the bits around in the following way:

  SIG-B common 0: DW 4 -> DW 7
  SIG-B common 1: DW 7 -> DW 8
  SIG-B common 2: DW 8 -> DW 4 (upper half)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The Free Software Foundation address is superfluous and causes
checkpatch to issue a warning when present.  Remove all paragraphs
with FSF's address to prevent that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

We offloaded all the RX configuration of init to firmware. However,
the configuration of interrupt coalescing was left hanging - it wasn't
offloaded nor was it written by host.

This write to the CSR is allowed in gen2, so the host can do it.
Without it we have various issues with RX fullness.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The parameter that indicated whether the LQ command should be sent
as sync or async was removed, causing the LQ command to be sent as
sync from interrupt context (e.g. from the RX path). This resulted
in a kernel warning: "scheduling while atomic" and failing to send
the LQ command, which ultimately leads to a queue hang.

Fix it by adding back the required parameter to send the command as
sync only when it is allowed.

Fixes: d94c5a82 ("iwlwifi: mvm: open BA session only when sta is authorized")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

When we receive TX response, we may release a few packets
due to a hole that was closed in the transmission window.

However, if that frame failed, we will mark all the released
frames as failed and will send multiple BARs.

This affects statistics badly, and cause unnecessary frames
transmission.

Instead, mark all the following packets as success, with the
desired result of sending a bar for the failed frame only.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

There is a bug in FW where the sequence control may be
incorrect, and the driver overrides it with the value
of the ieee80211 header.

However, in BAR there is no sequence control in the header,
which result with arbitrary sequence.

This access to an unknown location is bad and it makes the
logs very confusing - so fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

When the NIC is disconnected, we just can't do anything
besides seeking for help from the bus driver.  Dumping the
device's memory is not necessary and just bloats the logs
with unusable data.  Moreover, asking mac80211 to restart
the hardware is also useless.  Bypass all this.

Also, use the STATUS_TRANS_DEAD status bit instead of a
bool inside the transport layer. The advantage of this is
that now, the transport and the op_mode can know what is the
situation and bypass the useless recovery steps mentioned
above.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The new coex schema requires moving to SISO only when BT AG is 4.
Adjust the SISO criteria according to the coex schema version reported
by firmware.
Signed-off-by: Erel Geron <erelx.geron@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

When the NIC is disconnected from PCI bus, we are not
able to access it anymore. Check the status to avoid
some unnecessary work so can improve the performance.
It will help to make PCI bus rescan to bring back the
device much faster.

The real test is able to improve 7 seconds.

[w/o patch] It takes around 9 seconds
..
2018-04-20T01:22:39.691929-07:00 WARNING kernel:
[   66.335881] Timeout waiting for hardware access (CSR_GP_CNTRL 0xffffffff)
..
2018-04-20T01:22:48.101094-07:00 INFO kernel:
[   74.747364] iwlwifi 0000:01:00.0: loaded firmware version 29.610311.0 op_mode iwlmvm

[w/a patch] It takes about 2 seconds.
..
2018-04-20T01:18:16.454087-07:00 WARNING kernel:
[   75.966860] Timeout waiting for hardware access (CSR_GP_CNTRL 0xffffffff)
..
2018-04-20T01:18:18.602717-07:00 INFO kernel:
[   78.116132] iwlwifi 0000:01:00.0: loaded firmware version 29.610311.0 op_mode iwlmvm
..

Fixes: 49564a80 ("iwlwifi: pcie: remove non-responsive device")
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

There's no point in warning here, the user will just get an
error back to the debugfs file write, and warning just makes
it seem like there's an internal consistency problem when in
reality the user just happened to hit this at a bad time.
Remove the warning.

Fixes: f45f979d ("iwlwifi: mvm: disable dbg data collect when fw isn't alive")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Every rx mpdu cmd is built from cmd_hdr | 80211_hdr.  The problem is
that the size of cmd_hdr changes with API changes and we don't know
where the 80211_hdr starts.

By adding the size of cmd_hdr dynamically, we can ensure that we always
know how to parse mpdu frames, without dependending on the API changes.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

This will allow using the same init in future generations.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Store the default rxq number in a variable, so we won't need
to use the actual number in the code.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Update reduce tx power command API to be compatible with new FW API.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

While associated in low latency mode, or when traffic load is high,
don't enable EBS in scan request if fragmented EBS is not supported
by the FW.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The Free Software Foundation's address shouldn't be in the license
notice anymore, and some of our check scripts complain about it
(via checkpatch.pl).  Remove the address to silence it.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

This is used only within PCIe, and there's no reason to go through
the transport methods for a function call within PCIe itself.
Remove the dump_regs() method and call the function directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Allow other device generations to use the utilities that
are used to send and reclaim host commands and to allocate
rx, by making it non-static.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

We would like to allow using tx init code for other queues but
the command queue - for newer devices.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

We need to drop packets with errors (such as replay,
MIC, ICV, conversion, duplicate and so on).

Drop invalid packets, put the status bits in the metadata and
move the enum definition to the correct place (FW API header).
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The user can validate what was written to the file by reading it,
and check what is the default value before changing it.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The HE code is bloating the RX handling, and makes it too big.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The HE code is bloating the RX handling, and makes it too big.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Current implementation turns this bit on only for HE MU.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Add BSS color to the HE radiotap.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Some variables are used in iwl-fh.h, but their type's definition
isn't included. This may break compilation when using the file
without including the necessary dependencies first.

Add the required include to iwl-fh.h.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

A probe response built by a P2P GO should contain:
1. CSA/eCSA IE when relevant
2. If the corresponding probe request had P2P IE, then
need to add P2P IE with NOA attributes.

However, the NOA attributes and the updated channel switch
counter are known only to the FW. The solution is that FW
will send a notification with the relevant probe response
data and the driver will save it and update the probe
response accordingly.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

A new FW API has been added for WOWLAN_GET_STATUSES to support
multiple GTK keys and IGTK keys.  Check the respective TLV and use the
new API when it is set.

Let most of the code use the new version (v7) and convert the old
version (v6) to the new one when needed.

Also refactor some functions a bit so that they can be reused more
easily.  Particularly the part that calls WOWLAN_GET_STATUSES which is
reused in D3 and D0i3.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Runtime PM can only be used if CONFIG_PM is set.  Move all the d0i3
code (which is essentially runtime PM) behind the CONFIG_PM flag.

This prevents undefined usage of some functions when CONFIG_PM is not
defined.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

We repeated the same if twice in a row.  Remove the second one and
move the code block into the previous one.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

During d3, the firmware records debug data into internal buffer
if debug data collection occurs, collect the data that was written to the
buffer
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The tid for Non-QOS frames is set to IWL_MAX_TID_COUNT. This value
is also used for configuring the queue for non-QOS data. However, this
tid is used by the FW for management queues. As a result, the FW
does not encrypt non-QOS data frames.

Fix this by setting the tid for non-QOS data frames to zero, which
is a valid value for data frames in the FW.

This also fixes a bug in sending multicast frames, where the queues
are allocated with tid == 0, but are sent with tid == 8, which may
lead to unexpected behavior.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Upon first calling read() on a debugfs file, invoke
iwl_dbgfs_##name##_read and store the response buffer on the heap, so
subsequent read() calls don't need to invoke said function again.

This is done because cat etc will call read() repeatedly until EOF is
reached (or read() returns 0), which in the current implementation will
cause said function to be invoked multiple times.

With the current implementation this can also cause buggy behavior in
some weird edge cases where the first invocation returns a string of
length n, and the second of length m>n: The last m-n characters of
the second invocation will be printed to screen.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The iwl_dhc_tlc_cmd struct is not used, so remove it, including the
iwl_tcl_debug_flags enumeration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Don't enable debugging timestamps by default, so we save power by not
waking up the FW with timestamp commands.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

ath.git patches for 4.20. Major changes:

ath10k

* limit available channels via DT ieee80211-freq-limit

wil6210

* add 802.11r Fast Roaming support for AP and station modes

* add support for channel 4

Tri-band devices (1x 2.4GHz + 2x 5GHz) often incorporate special filters in
the RX and TX path. These filtered channel can in theory still be used by
the hardware but the signal strength is reduced so much that it makes no
sense.

There is already a DT property to limit the available channels but ath10k
has to manually call this functionality to limit the currrently set wiphy
channels further.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Check rx_buff_mgmt is allocated before accessing its internal fields.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This feature is needed for enterprise APs and clients to enable
fast roaming as defined in 802.11r between APs in the same ESS.

On AP side, this feature is supported only when disable_ap_sme
is enabled.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

RX SKBs are released in both wil6210 rmmod and RX handle.
As there is no lock to protect the buffers DMA unmap,
the SKB pointer in buff_arr is used to check if the buffer
memory was already released.
Setting wil->rx_buff_mgmt.buff_arr[buff_id].skb to NULL before the DMA
memory unmap will prevent duplicate unmapping of the same memory.
Move the buffer ID to the free list also in case the SKB is NULL.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>