Clear device initiated resume variables once device is fully up and running
in U0 state.

Resume needs to be signaled for 20ms for usb2 devices before they can be
moved to U0 state.

An interrupt is triggered if a device initiates resume. As we handle the
event in interrupt context we can not sleep for 20ms, so we instead set
a resume flag, a timestamp, and start the roothub polling.

The roothub code will later move the port to U0 when it finds a port in
resume state with the resume flag set, and timestamp passed by 20ms.

A host initiated resume is however not done in interrupt context, and
host initiated resume code will directly signal resume, wait 20ms and then
move the port to U0.

These two codepaths can race, if we are in the middle of a host initated
resume, while sleeping for 20ms, we may handle a port event and find the
port in resume state. The port event handling code will assume the resume
was device initiated and set the resume flag and timestamp.

Root hub code will however not catch the port in resume state again as the
host initated resume code has already moved the port to U0.
The resume flag and timestamp will remain set for this port preventing port
from suspending again  (LPM setting port to U3)

Fix this for now by always clearing the device initated resume parameters
once port is in U0

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Function ep_ring_is_processing() checks the dequeue pointer
in endpoint context to know whether an endpoint is busy with
processing TRBs. This is not correct since dequeue pointer
field in an endpoint context is only valid when the endpoint
is in Halted or Stopped states. This buggy code causes audio
noise when playing sound with USB headset connected to host
controllers which support CFC (one of xhci 1.1 features).

This patch should exist in stable kernel since v4.3.
Reported-and-tested-by: YD Tseng <yd_tseng@asmedia.com.tw>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable <stable@vger.kernel.org> # v4.3
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Existing Intel xHCI controllers require a delay of 1 mS,
after setting the CMD_RESET bit in command register, before
accessing any HC registers. This allows the HC to complete
the reset operation and be ready for HC register access.
Without this delay, the subsequent HC register access,
may result in a system hang, very rarely.

Verified CherryView / Braswell platforms go through over
5000 warm reboot cycles (which was not possible without
this patch), without any xHCI reset hang.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'usb-ci-v4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus

Peter writes:

USB Chipidea Fixes for v4.4-rc2

The first four fixes was for v4.3-rc7, but it is too late
at that time, and other two small fixes are for possible NULL
pointer issue.

of_match_device could return NULL, and so cause a NULL pointer
dereference later.

Reported-by: coverity (CID 1324138)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>

of_match_device could return NULL, and so cause a NULL pointer
dereference later. Renaming tmp_dev to of_id (like all others do) in the
process.

Reported-by: coverity (CID 1324135)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>

This patch is to support load and unload gadget driver in full OTG mode.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Jiada Wang <jiada_wang@mentor.com>
Cc: <stable@vger.kernel.org> #v4.0+

Since the ci->role will be set after the host role start is complete, there
will be nobody cared irq during start host if usb irq enabled. This error
can be reproduced on i.mx6 sololite EVK board by:
1. disable otg id irq(IDIE) and disable all real otg properties of usbotg1
   in dts.
2. boot up the board with ID cable and usb device connected.
3. echo gadget > /sys/kernel/debug/ci_hdrc.0/role
4. echo host > /sys/kernel/debug/ci_hdrc.0/role
5. irq 212: nobody cared.

Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>

For imx27, it needs three clocks to let the controller work,
the old code is wrong, and usbmisc has not included clock handling
code any more. Without this patch, it will cause below data
abort when accessing usbmisc registers.

usbcore: registered new interface driver usb-storage
Unhandled fault: external abort on non-linefetch (0x008) at 0xf4424600
pgd = c0004000
[f4424600] *pgd=10000452(bad)
Internal error: : 8 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.1.0-next-20150701-dirty #3089
Hardware name: Freescale i.MX27 (Device Tree Support)
task: c7832b60 ti: c783e000 task.ti: c783e000
PC is at usbmisc_imx27_init+0x4c/0xbc
LR is at usbmisc_imx27_init+0x40/0xbc
pc : [<c03cb5c0>]    lr : [<c03cb5b4>]    psr: 60000093
sp : c783fe08  ip : 00000000  fp : 00000000
r10: c0576434  r9 : 0000009c  r8 : c7a773a0
r7 : 01000000  r6 : 60000013  r5 : c7a776f0  r4 : c7a773f0
r3 : f4424600  r2 : 00000000  r1 : 00000001  r0 : 00000001
Flags: nZCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 0005317f  Table: a0004000  DAC: 00000017
Process swapper (pid: 1, stack limit = 0xc783e190)
Stack: (0xc783fe08 to 0xc7840000)
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: <stable@vger.kernel.org> #v4.1+
Acked-by: Shawn Guo <shawnguo@kernel.org>

Some i.mx platforms need three clocks to let controller work, but
others only need one, refine clock operation to adapt for all
platforms, it fixes a regression found at i.mx27.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: <stable@vger.kernel.org> #v4.1+

Merge tag 'fixes-for-v4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

usb: fixes for v4.4-rc2

First round of fixes for this -rc cycle. We have the
usual set of miscellaneous fixes. The important
thing here is support for Intel Broxton SoC on dwc3,
some fixes for Rockchip SoCs on dwc2 and a fix on
dwc3 to let it report lower speeds than
USB_SPEED_SUPER.

Following changes that appeared in lk 4.0.0, the gadget udc driver for
some ARM based Atmel SoCs (e.g. at91sam9x5 and sama5d3 families)
incorrectly deduced full-speed USB link speed even when the hardware
had negotiated a high-speed link. The fix is to make sure that the
UDPHS Interrupt Enable Register value does not mask the SPEED bit
in the Interrupt Status Register.

For a mass storage gadget this problem lead to failures when the host
had a USB 3 port with the xhci_hcd driver. If the host was a USB 2
port using the ehci_hcd driver then the mass storage gadget worked
(but probably at a lower speed than it should have).
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org> #4.0+
Fixes: 9870d895 ("usb: atmel_usba_udc: Mask status with enabled irqs")
Signed-off-by: Felipe Balbi <balbi@ti.com>

Change the permission of usb_dma parameter so it can
be used for runtime debug without reboot.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

In some SoCs, dwc3 is implemented as a USB2.0 only
core, meaning that it can't ever achieve SuperSpeed.

Currect driver always sets gadget.max_speed to
USB_SPEED_SUPER unconditionally. This can causes
issues to some Host stacks where the host will issue
a GetBOS() request and we will reply with a BOS
containing Superspeed Capability Descriptor.

At least Windows seems to be upset by this fact and
prints a warning that we should connect $this device
to another port.

[ balbi@ti.com : rewrote entire commit, including
source code comment to make a lot clearer what the
problem is ]

Cc: <stable@vger.kernel.org>
Signed-off-by: Ben McCauley <ben.mccauley@garmin.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Here are a few changes in musb_h_tx_flush_fifo().

- It has been observed that sometimes (if not always) musb is unable
  to flush tx fifo during urb dequeue when disconnect a device. But
  it seems to be harmless, since the tx fifo flush is done again in
  musb_ep_program() when re-use the hw_ep.

  But the WARN() floods the console in the case when multiple tx urbs
  are queued, so change it to dev_WARN_ONCE().

- applications could queue up many tx urbs, then the 1ms delay could
  causes minutes of delay in device disconnect. So remove it to get
  better user experience. The 1ms delay does not help the flushing
  anyway.

- cleanup the debug code - related to lastcsr.

----
Note: The tx fifo flush issue has been observed during device disconnect
on AM335x.

To reproduce the issue, ensure tx urb(s) are queued when unplug the usb
device which is connected to AM335x usb host port.

I found using a usb-ethernet device and running iperf (client on AM335x)
has very high chance to trigger the problem.

Better to turn on dev_dbg() in musb_cleanup_urb() with CPPI enabled to
see the issue when aborting the tx channel.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The current code tries to allocate memory with GFP_KERNEL at
interrupt context, it would show below warning during the enumeration
when I test it with chipidea hardware, change GFP flag as GFP_ATOMIC
can fix this issue.

[   40.438237] zero gadget: high-speed config #2: loopback
[   40.444924] ------------[ cut here ]------------
[   40.449609] WARNING: CPU: 0 PID: 0 at kernel/locking/lockdep.c:2755 lockdep_trace_alloc+0x108/0x128()
[   40.461715] DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
[   40.467130] Modules linked in:
[   40.470216]  usb_f_ss_lb g_zero libcomposite evbug
[   40.473822] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.3.0-rc5-00168-gb730aaf #604
[   40.481496] Hardware name: Freescale i.MX6 SoloX (Device Tree)
[   40.487345] Backtrace:
[   40.489857] [<80014e94>] (dump_backtrace) from [<80015088>] (show_stack+0x18/0x1c)
[   40.497445]  r6:80b67a80 r5:00000000 r4:00000000 r3:00000000
[   40.503234] [<80015070>] (show_stack) from [<802e27b4>] (dump_stack+0x8c/0xa4)
[   40.510503] [<802e2728>] (dump_stack) from [<8002cfe8>] (warn_slowpath_common+0x80/0xbc)
[   40.518612]  r6:8007510c r5:00000009 r4:80b49c88 r3:00000001
[   40.524396] [<8002cf68>] (warn_slowpath_common) from [<8002d05c>] (warn_slowpath_fmt+0x38/0x40)
[   40.533109]  r8:bcfdef80 r7:bdb705cc r6:000080d0 r5:be001e80 r4:809cc278
[   40.539965] [<8002d028>] (warn_slowpath_fmt) from [<8007510c>] (lockdep_trace_alloc+0x108/0x128)
[   40.548766]  r3:809d0128 r2:809cc278
[   40.552401]  r4:600b0193
[   40.554990] [<80075004>] (lockdep_trace_alloc) from [<801093d4>] (kmem_cache_alloc+0x28/0x15c)
[   40.563618]  r4:000080d0 r3:80b4aa8c
[   40.567270] [<801093ac>] (kmem_cache_alloc) from [<804d95e4>] (ep_alloc_request+0x58/0x68)
[   40.575550]  r10:7f01f104 r9:00000001 r8:bcfdef80 r7:bdb705cc r6:bc178700 r5:00000000
[   40.583512]  r4:bcfdef80 r3:813c0a38
[   40.587183] [<804d958c>] (ep_alloc_request) from [<7f01f7ec>] (loopback_set_alt+0x114/0x21c [usb_f_ss_lb])
[   40.596929] [<7f01f6d8>] (loopback_set_alt [usb_f_ss_lb]) from [<7f006910>] (composite_setup+0xbd0/0x17e8 [libcomposite])
[   40.607902]  r10:bd3a2c0c r9:00000000 r8:bcfdef80 r7:bc178700 r6:bdb702d0 r5:bcfdefdc
[   40.615866]  r4:7f0199b4 r3:00000002
[   40.619542] [<7f005d40>] (composite_setup [libcomposite]) from [<804dae88>] (udc_irq+0x784/0xd1c)
[   40.628431]  r10:80bb5619 r9:c0876140 r8:00012001 r7:bdb71010 r6:bdb70568 r5:00010001
[   40.636392]  r4:bdb70014
[   40.638985] [<804da704>] (udc_irq) from [<804d64f8>] (ci_irq+0x5c/0x118)
[   40.645702]  r10:80bb5619 r9:be11e000 r8:00000117 r7:00000000 r6:bdb71010 r5:be11e060
[   40.653666]  r4:bdb70010
[   40.656261] [<804d649c>] (ci_irq) from [<8007f638>] (handle_irq_event_percpu+0x7c/0x13c)
[   40.664367]  r6:00000000 r5:be11e060 r4:bdb05cc0 r3:804d649c
[   40.670149] [<8007f5bc>] (handle_irq_event_percpu) from [<8007f740>] (handle_irq_event+0x48/0x6c)
[   40.679036]  r10:00000000 r9:be008000 r8:00000001 r7:00000000 r6:bdb05cc0 r5:be11e060
[   40.686998]  r4:be11e000
[   40.689581] [<8007f6f8>] (handle_irq_event) from [<80082850>] (handle_fasteoi_irq+0xd4/0x1b0)
[   40.698120]  r6:80b56a30 r5:be11e060 r4:be11e000 r3:00000000
[   40.703898] [<8008277c>] (handle_fasteoi_irq) from [<8007ec04>] (generic_handle_irq+0x28/0x3c)
[   40.712524]  r7:00000000 r6:80b4aaf4 r5:00000117 r4:80b445fc
[   40.718304] [<8007ebdc>] (generic_handle_irq) from [<8007ef20>] (__handle_domain_irq+0x6c/0xe8)
[   40.727033] [<8007eeb4>] (__handle_domain_irq) from [<800095d4>] (gic_handle_irq+0x48/0x94)
[   40.735402]  r9:c080f100 r8:80b4ac6c r7:c080e100 r6:80b67d40 r5:80b49f00 r4:c080e10c
[   40.743290] [<8000958c>] (gic_handle_irq) from [<80015d38>] (__irq_svc+0x58/0x78)
[   40.750791] Exception stack(0x80b49f00 to 0x80b49f48)
[   40.755873] 9f00: 00000001 00000001 00000000 80024320 80b48000 80b4a9d0 80b4a984 80b433e4
[   40.764078] 9f20: 00000001 807f4680 00000000 80b49f5c 80b49f20 80b49f50 80071ca4 800113fc
[   40.772272] 9f40: 200b0013 ffffffff
[   40.775776]  r9:807f4680 r8:00000001 r7:80b49f34 r6:ffffffff r5:200b0013 r4:800113fc
[   40.783677] [<800113d4>] (arch_cpu_idle) from [<8006c5bc>] (default_idle_call+0x28/0x38)
[   40.791798] [<8006c594>] (default_idle_call) from [<8006c6dc>] (cpu_startup_entry+0x110/0x1b0)
[   40.800445] [<8006c5cc>] (cpu_startup_entry) from [<807e95dc>] (rest_init+0x12c/0x168)
[   40.808376]  r7:80b4a8c0 r3:807f4b7c
[   40.812030] [<807e94b0>] (rest_init) from [<80ad7cc0>] (start_kernel+0x360/0x3d4)
[   40.819528]  r5:80bcb000 r4:80bcb050
[   40.823171] [<80ad7960>] (start_kernel) from [<8000807c>] (0x8000807c)

It fixes commit 91c42b0d ("usb: gadget: loopback: Fix looping back
logic implementation").

Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

In commit 734643df ("usb: dwc2: host: add flag to reflect bus
state") we changed dwc2_port_suspend() not to set the lx_state
anymore (instead it sets the new bus_suspended variable).  This
introduced a bug where we would fail to detect device insertions if:

1. Plug empty hub into dwc2
2. Plug USB flash drive into the empty hub.
3. Wait a few seconds
4. Unplug USB flash drive
5. Less than 2 seconds after step 4, plug the USB flash drive in again.

The dwc2_hcd_rem_wakeup() function should have been changed to look at
the new bus_suspended variable.

Let's fix it.  Since commit b46146d5 ("usb: dwc2: host: resume root
hub on remote wakeup") talks about needing the root hub resumed if the
bus was suspended, we'll include it in our test.

It appears that the "port_l1_change" should only be set to 1 if we were
in DWC2_L1 (the driver currently never sets this), so we'll update the
former "else" case based on this test.

Fixes: 734643df ("usb: dwc2: host: add flag to reflect bus state")
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Gregory Herrero <gregory.herrero@intel.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The comment for ahbcfg for rk3066 parameters (also used for rk3288)
claimed that ahbcfg was INCR16, but it wasn't.  Since the bits weren't
shifted properly, the 0x7 ended up being masked and we ended up
programming 0x3 for the HBstLen.  Let's set it to INCR16 properly.

As per Wu Liang Feng at Rockchip this may increase transmission
efficiency.  I did blackbox tests with writing 0s to a USB-based SD
reader (forcefully capping CPU Freq to try to measure efficiency):
  cd /sys/devices/system/cpu/cpu0/cpufreq
  echo userspace > scaling_governor
  echo 126000 > scaling_setspeed
  for i in $(seq 10); do
    dd if=/dev/zero of=/dev/sdb bs=1M count=750
  done

With the above tests I found that speeds went from ~15MB/s to ~18MB/s.
Note that most other tests I did (including reading from the same USB
reader) didn't show any difference in performance.
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: John Youn <johnyoun@synopsys.com>
Reviewed-by: Liangfeng Wu <wulf@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

otg_dev->extcon was referenced before otg_dev was initialized. Fix.

Cc: <stable@vger.kernel.org> # v4.3
Fixes: a2fd2423 ("usb: phy: omap-otg: Replace deprecated API of extcon")
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>

There is a bit of a mess in the order of arguments to the ulpi write
callback. There is

	int ulpi_write(struct ulpi *ulpi, u8 addr, u8 val)

in drivers/usb/common/ulpi.c;

	struct usb_phy_io_ops {
		...
		int (*write)(struct usb_phy *x, u32 val, u32 reg);
	}

in include/linux/usb/phy.h.

The callback registered by the musb driver has to comply to the latter,
but up to now had "offset" first which effectively made the function
broken for correct users. So flip the order and while at it also
switch to the parameter names of struct usb_phy_io_ops's write.

Fixes: ffb865b1 ("usb: musb: add ulpi access operations")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

PCI IDs for Broxton based platforms.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Pull perf updates from Thomas Gleixner:
 "Mostly updates to the perf tool plus two fixes to the kernel core code:

   - Handle tracepoint filters correctly for inherited events (Peter
     Zijlstra)

   - Prevent a deadlock in perf_lock_task_context (Paul McKenney)

   - Add missing newlines to some pr_err() calls (Arnaldo Carvalho de
     Melo)

   - Print full source file paths when using 'perf annotate --print-line
     --full-paths' (Michael Petlan)

   - Fix 'perf probe -d' when just one out of uprobes and kprobes is
     enabled (Wang Nan)

   - Add compiler.h to list.h to fix 'make perf-tar-src-pkg' generated
     tarballs, i.e. out of tree building (Arnaldo Carvalho de Melo)

   - Add the llvm-src-base.c and llvm-src-kbuild.c files, generated by
     the 'perf test' LLVM entries, when running it in-tree, to
     .gitignore (Yunlong Song)

   - libbpf error reporting improvements, using a strerror interface to
     more precisely tell the user about problems with the provided
     scriptlet, be it in C or as a ready made object file (Wang Nan)

   - Do not be case sensitive when searching for matching 'perf test'
     entries (Arnaldo Carvalho de Melo)

   - Inform the user about objdump failures in 'perf annotate' (Andi
     Kleen)

   - Improve the LLVM 'perf test' entry, introduce a new ones for BPF
     and kbuild tests to check the environment used by clang to compile
     .c scriptlets (Wang Nan)"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
  perf/x86/intel/rapl: Remove the unused RAPL_EVENT_DESC() macro
  tools include: Add compiler.h to list.h
  perf probe: Verify parameters in two functions
  perf session: Add missing newlines to some pr_err() calls
  perf annotate: Support full source file paths for srcline fix
  perf test: Add llvm-src-base.c and llvm-src-kbuild.c to .gitignore
  perf: Fix inherited events vs. tracepoint filters
  perf: Disable IRQs across RCU RS CS that acquires scheduler lock
  perf test: Do not be case sensitive when searching for matching tests
  perf test: Add 'perf test BPF'
  perf test: Enhance the LLVM tests: add kbuild test
  perf test: Enhance the LLVM test: update basic BPF test program
  perf bpf: Improve BPF related error messages
  perf tools: Make fetch_kernel_version() publicly available
  bpf tools: Add new API bpf_object__get_kversion()
  bpf tools: Improve libbpf error reporting
  perf probe: Cleanup find_perf_probe_point_from_map to reduce redundancy
  perf annotate: Inform the user about objdump failures in --stdio
  perf stat: Make stat options global
  perf sched latency: Fix thread pid reuse issue
  ...

Pull scheduler fix from Thomas Gleixner:
 "A single fix to prevent math underflow in the numa balancing code"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/numa: Fix math underflow in task_tick_numa()

Pull liblockdep fixes from Thomas Gleixner:
 "Three small patches to synchronize liblockdep with the latest core
  changes"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tools/liblockdep: explicitly declare lockdep API we call from liblockdep
  tools/liblockdep: add userspace versions of WRITE_ONCE and RCU_INIT_POINTER
  tools/liblockdep: remove task argument from debug_check_no_locks_held

Pull x86 fixes from Thomas Gleixner:
 "A couple of fixes and updates related to x86:

   - Fix the W+X check regression on XEN

   - The real fix for the low identity map trainwreck

   - Probe legacy PIC early instead of unconditionally allocating legacy
     irqs

   - Add cpu verification to long mode entry

   - Adjust the cache topology to AMD Fam17H systems

   - Let Merrifield use the TSC across S3"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu: Call verify_cpu() after having entered long mode too
  x86/setup: Fix low identity map for >= 2GB kernel range
  x86/mm: Skip the hypervisor range when walking PGD
  x86/AMD: Fix last level cache topology for AMD Fam17h systems
  x86/irq: Probe for PIC presence before allocating descs for legacy IRQs
  x86/cpu/intel: Enable X86_FEATURE_NONSTOP_TSC_S3 for Merrifield

Merge branches 'irq-urgent-for-linus' and 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull irq and timer fixes from Thomas Gleixner:

 - An irq regression fix to restore the wakeup behaviour of chained
   interrupts.

 - A timer fix for a long standing race versus timers scheduled on a
   target cpu which got exposed by recent changes in the workqueue
   implementation.

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/PM: Restore system wake up from chained interrupts

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timers: Use proper base migration in add_timer_on()

Pull MIPS updates from Ralf Baechle:
 "These are the highlists of the main MIPS pull request for 4.4:

   - Add latencytop support
   - Support appended DTBs
   - VDSO support and initially use it for gettimeofday.
   - Drop the .MIPS.abiflags and ELF NOTE sections from vmlinux
   - Support for the 5KE, an internal test core.
   - Switch all MIPS platfroms to libata drivers.
   - Improved support, cleanups for ralink and Lantiq platforms.
   - Support for the new xilfpga platform.
   - A number of DTB improvments for BMIPS.
   - Improved support for CM and CPS.
   - Minor JZ4740 and BCM47xx enhancements"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (120 commits)
  MIPS: idle: add case for CPU_5KE
  MIPS: Octeon: Support APPENDED_DTB
  MIPS: vmlinux: create a section for appended DTB
  MIPS: Clean up compat_siginfo_t
  MIPS: Fix PAGE_MASK definition
  MIPS: BMIPS: Enable GZIP ramdisk and timed printks
  MIPS: Add xilfpga defconfig
  MIPS: xilfpga: Add mipsfpga platform code
  MIPS: xilfpga: Add xilfpga device tree files.
  dt-bindings: MIPS: Document xilfpga bindings and boot style
  MIPS: Make MIPS_CMDLINE_DTB default
  MIPS: Make the kernel arguments from dtb available
  MIPS: Use USE_OF as the guard for appended dtb
  MIPS: BCM63XX: Use pr_* instead of printk
  MIPS: Loongson: Cleanup CONFIG_LOONGSON_SUSPEND.
  MIPS: lantiq: Disable xbar fpi burst mode
  MIPS: lantiq: Force the crossbar to big endian
  MIPS: lantiq: Initialize the USB core on boot
  MIPS: lantiq: Return correct value for fpi clock on ar9
  MIPS: ralink: Add missing clock on rt305x
  ...

Pull sound fixes from Takashi Iwai:
 "Here are a collection of small fixes tha have been gathered for
  4.4-rc1.  The only significant changes are those in PCI drivers
  Kconfig, to use "depends on" instead of "select" for CONFIG_ZONE_DMA.
  A reverse select is often more user-friendly, but in this case, it
  makes hard to manage with the conflict with ZONE_DEVICE, so changed in
  such a way for now.

  Others are all small fixes and quirks: an error check in soundcore
  reigster_chrdev(), HD-audio HDMI/DP phantom jack fix, Intel Broxton DP
  quirk, USB-audio DSD device quirk, some constifications, etc"

* tag 'sound-fix-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: pci: depend on ZONE_DMA
  ALSA: hda - Simplify phantom jack handling for HDMI/DP
  ALSA: hda/hdmi - apply Skylake fix-ups to Broxton display codec
  ALSA: ctxfi: constify rsc ops structures
  ALSA: usb: Add native DSD support for Aune X1S
  ALSA: oxfw: add an comment to Kconfig for TASCAM FireOne
  sound: fix check for error condition of register_chrdev()

Pull ARC fixes from Vineet Gupta:
 "Found a couple of brown paper bag bugs with the prev pull request
  (including a SMP build breakage report from Guenter).  Since these are
  urgent I also decided to send over a bunch of other pending fixes
  which could have otherwise waited an rc or two.

  Summary:

   - A bunch of brown paper bag bugs (MAINTAINERS list email, SMP build
     failure)
   - cpu_relax() now compiler barrier for UP as well
   - handling of userspace Bus Errors for ARCompact builds"

* tag 'arc-4.4-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: Fix silly typo in MAINTAINERS file
  ARC: cpu_relax() to be compiler barrier even for UP
  ARC: use ASL assembler mnemonic
  ARC: [arcompact] Handle bus error from userspace as Interrupt not exception
  ARC: remove extraneous header include
  ARCv2: lib: memcpy: use local symbols

cpu_relax() on ARC has been barrier only for SMP (and no-op for UP). Per
recent discussions, it is safer to make it a compiler barrier
unconditionally.

Link: http://lkml.kernel.org/r/53A7D3AA.9020100@synopsys.comAcked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

ARCompact and ARCv2 only have ASL, while binutils used to support LSL as
a alias mnemonic.

Newer binutils (upstream) don't want to do that so replace it.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Bus errors from userspace on ARCompact based cores are handled by core
as a high priority L2 interrupt but current code treated it as interrupt
Handling an interrupt like exception is certainly not going to go unnoticed.
(and it worked so far as we never saw a Bus error from userspace until
IPPK guys tested a DDR controller with ECC error detection etc hence
needed to explicitly trigger/handle such errors)

 - So move mem_service exception handler from common code into ARCv2 code.
 - In ARCompact code, define  mem_service as L2 interrupt handler which
   just drops down to pure kernel mode and goes of to enqueue SIGBUS
Reported-by: Nelson Pereira <npereira@synopsys.com>
Tested-by: Ana Martins <amartins@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Merge tag 'chrome-platform-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform

Pull chrome platform updates from Olof Johansson:
 "Here's the branch of chrome platform changes for v4.4.  Some have been
  queued up for the full 4.3 release cycle since I forgot to send them
  in for that round (rebased early on to deal with fixes conflicts).

  Most of these enable EC communication stuff -- Pixel 2015 support,
  enabling building for ARM64 platforms, and a few fixes for memory
  leaks.

  There's also a patch in here to allow reading/writing the verified
  boot context, which depends on a sysfs patch acked by Greg"

* tag 'chrome-platform-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
  platform/chrome: Fix i2c-designware adapter name
  platform/chrome: Support reading/writing the vboot context
  sysfs: Support is_visible() on binary attributes
  platform/chrome: cros_ec: Fix possible leak in led_rgb_store()
  platform/chrome: cros_ec: Fix leak in sequence_store()
  platform/chrome: Enable Chrome platforms on 64-bit ARM
  platform/chrome: cros_ec_dev - Add a platform device ID table
  platform/chrome: cros_ec_lpc - Add support for Google Pixel 2
  platform/chrome: cros_ec_lpc - Use existing function to check EC result
  platform/chrome: Make depends on MFD_CROS_EC instead CROS_EC_PROTO
  Revert "platform/chrome: Don't make CHROME_PLATFORMS depends on X86 || ARM"

Merge tag 'platform-drivers-x86-v4.4-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86

Pull another x86 platform driver update from Darren Hart:
 "Support for the unfortunately rather unique ESC key on the Ideapad
  Yoga 3 and two DMI matches for rfkill support.  Solitary fix for
  potential missed errors for asus-wmi.  Downgrade a thinkpad_acpi
  message to info.

  asus-wmi:
   - fix error handling in store_sys_wmi()

  ideapad-laptop:
   - Add Lenovo Yoga 900 to no_hw_rfkill dmi list
   - include Yoga 3 1170 in add rfkill whitelist
   - add support for Yoga 3 ESC key

  thinkpad_acpi:
   - Don't yell on unsupported brightness interfaces"

* tag 'platform-drivers-x86-v4.4-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
  asus-wmi: fix error handling in store_sys_wmi()
  ideapad-laptop: Add Lenovo Yoga 900 to no_hw_rfkill dmi list
  ideapad-laptop: include Yoga 3 1170 in add rfkill whitelist
  ideapad-laptop: add support for Yoga 3 ESC key
  thinkpad_acpi: Don't yell on unsupported brightness interfaces

Pull more input updates from Dmitry Torokhov:
 "An update to the tsc2005 driver that allows it to also support tsc2004
  (basically the same controller, but uses i2c instead of spi bus), and
  a couple of bug fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: parkbd - drop bogus __init from parkbd_allocate_serio()
  Input: elantech - add Fujitsu Lifebook U745 to force crc_enabled
  Input: tsc2004 - add support for tsc2004
  Input: tsc200x-core - rename functions and variables
  Input: tsc2005 - separate SPI and core functions

Pull final round of SCSI updates from James Bottomley:
 "Sorry for the delay in this patch which was mostly caused by getting
  the merger of the mpt2/mpt3sas driver, which was seen as an essential
  item of maintenance work to do before the drivers diverge too much.
  Unfortunately, this caused a compile failure (detected by linux-next),
  which then had to be fixed up and incubated.

  In addition to the mpt2/3sas rework, there are updates from pm80xx,
  lpfc, bnx2fc, hpsa, ipr, aacraid, megaraid_sas, storvsc and ufs plus
  an assortment of changes including some year 2038 issues, a fix for a
  remove before detach issue in some drivers and a couple of other minor
  issues"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
  mpt3sas: fix inline markers on non inline function declarations
  sd: Clear PS bit before Mode Select.
  ibmvscsi: set max_lun to 32
  ibmvscsi: display default value for max_id, max_lun and max_channel.
  mptfusion: don't allow negative bytes in kbuf_alloc_2_sgl()
  scsi: pmcraid: replace struct timeval with ktime_get_real_seconds()
  mvumi: 64bit value for seconds_since1970
  be2iscsi: Fix bogus WARN_ON length check
  scsi_scan: don't dump trace when scsi_prep_async_scan() is called twice
  mpt3sas: Bump mpt3sas driver version to 09.102.00.00
  mpt3sas: Single driver module which supports both SAS 2.0 & SAS 3.0 HBAs
  mpt2sas, mpt3sas: Update the driver versions
  mpt3sas: setpci reset kernel oops fix
  mpt3sas: Added OEM Gen2 PnP ID branding names
  mpt3sas: Refcount fw_events and fix unsafe list usage
  mpt3sas: Refcount sas_device objects and fix unsafe list usage
  mpt3sas: sysfs attribute to report Backup Rail Monitor Status
  mpt3sas: Ported WarpDrive product SSS6200 support
  mpt3sas: fix for driver fails EEH, recovery from injected pci bus error
  mpt3sas: Manage MSI-X vectors according to HBA device type
  ...