Pull sound fixes from Takashi Iwai:
 "Only a few small HD-audio fixes:
   - Addition of new Conexant codec IDs
   - Two one-liners to add fixups for Realtek codecs
   - A last-minute regression fix for auto-mute with power-saving mode
     (regressed since 3.8-rc1)"

* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Fix inconsistent pin states after resume
  ALSA: hda - Add Conexant CX20755/20756/20757 codec IDs
  ALSA: hda - Add fixup for Acer AO725 laptop
  ALSA: hda - Fix mute led for another HP machine

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The commit [26a6cb6c: ALSA: hda - Implement a poll loop for jacks as a
module parameter] introduced the polling jack detection code, but it
also moved the call of snd_hda_jack_set_dirty_all() in the resume path
after resume/init ops call.  This caused a regression when the jack
state has been changed during power-down (e.g. in the power save
mode).  Since the driver doesn't probe the new jack state but keeps
using the cached value due to no dirty flag, the pin state remains
also as if the jack is still plugged.

The fix is simply moving snd_hda_jack_set_dirty_all() to the original
position.
Reported-by: Manolo Díaz <diaz.manolo@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Pull PCI updates from Bjorn Helgaas:
 "The most important is a fix for a pciehp deadlock that occurs when
  unplugging a Thunderbolt adapter.  We also applied the same fix to
  shpchp, removed CONFIG_EXPERIMENTAL dependencies, fixed a
  pcie_aspm=force problem, and fixed a refcount leak.

  Details:

   - Hotplug
      PCI: pciehp: Use per-slot workqueues to avoid deadlock
      PCI: shpchp: Make shpchp_wq non-ordered
      PCI: shpchp: Handle push button event asynchronously
      PCI: shpchp: Use per-slot workqueues to avoid deadlock

   - Power management
      PCI: Allow pcie_aspm=force even when FADT indicates it is unsupported

   - Misc
      PCI/AER: pci_get_domain_bus_and_slot() call missing required pci_dev_put()
      PCI: remove depends on CONFIG_EXPERIMENTAL"

* tag '3.8-pci-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: remove depends on CONFIG_EXPERIMENTAL
  PCI: Allow pcie_aspm=force even when FADT indicates it is unsupported
  PCI: shpchp: Use per-slot workqueues to avoid deadlock
  PCI: shpchp: Handle push button event asynchronously
  PCI: shpchp: Make shpchp_wq non-ordered
  PCI/AER: pci_get_domain_bus_and_slot() call missing required pci_dev_put()
  PCI: pciehp: Use per-slot workqueues to avoid deadlock

Commit 083b804c ("async: use workqueue for worker pool") made it
possible that async jobs are moved from pending to running out-of-order.
While pending async jobs will be queued and dispatched for execution in
the same order, nothing guarantees they'll enter "1) move self to the
running queue" of async_run_entry_fn() in the same order.

Before the conversion, async implemented its own worker pool.  An async
worker, upon being woken up, fetches the first item from the pending
list, which kept the executing lists sorted.  The conversion to
workqueue was done by adding work_struct to each async_entry and async
just schedules the work item.  The queueing and dispatching of such work
items are still in order but now each worker thread is associated with a
specific async_entry and moves that specific async_entry to the
executing list.  So, depending on which worker reaches that point
earlier, which is non-deterministic, we may end up moving an async_entry
with larger cookie before one with smaller one.

This broke __lowest_in_progress().  running->domain may not be properly
sorted and is not guaranteed to contain lower cookies than pending list
when not empty.  Fix it by ensuring sort-inserting to the running list
and always looking at both pending and running when trying to determine
the lowest cookie.

Over time, the async synchronization implementation became quite messy.
We better restructure it such that each async_entry is linked to two
lists - one global and one per domain - and not move it when execution
starts.  There's no reason to distinguish pending and running.  They
behave the same for synchronization purposes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull perf/urgent fixes from Arnaldo Carvalho de Melo:

 . revert 20b279 - require exclude_guest to use PEBS - kernel side, now
   older binaries will continue working for things like cycles:pp
   without needing to pass extra modifiers, from David Ahern.

 . Fix building from 'make perf-*-src-pkg' tarballs, broken by UAPI,
   from Sebastian Andrzej Siewior

[ Pulling directly, Ingo would normally pull but has been unresponsive ]

* tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
  perf tools: Fix building from 'make perf-*-src-pkg' tarballs
  perf x86: revert 20b279 - require exclude_guest to use PEBS - kernel side

Pull parisc fixes from Helge Deller:
 "Improve the stability of the linux kernel on the parisc architecture"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: sigaltstack doesn't round ss.ss_sp as required
  parisc: improve ptrace support for gdb single-step
  parisc: don't claim cpu irqs more than once
  parisc: avoid undefined shift in cnv_float.h

Pull fuse fixes from Miklos Szeredi:
 "This contain a bugfix for CUSE and miscellaneous small fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: remove unused variable in fuse_try_move_page()
  fuse: make fuse_file_fallocate() static
  fuse: Move CUSE Kconfig entry from fs/Kconfig into fs/fuse/Kconfig
  cuse: fix uninitialized variable warnings
  cuse: do not register multiple devices with identical names
  cuse: use mutex as registration lock instead of spinlocks

Pull GPIO fixes from Linus Walleij:
 "Here are some GPIO fixes I stacked up in my GPIO tree:

   - Remove a bad #include from the Samsung driver
   - Some Kconfig hazzle for the Samsungs
   - Skip gpiolib registration on EXYNOS5440
   - Don't free the MVEBU label"

* tag 'fixes-for-v3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: mvebu: Don't free chip label memory
  gpio: samsung: skip gpio lib registration for EXYNOS5440
  gpio: samsung: silent build warning for EXYNOS5 SoCs
  gpio: samsung: fix pinctrl condition for exynos and exynos5440
  gpio: samsung: remove inclusion <mach/regs-clock.h>

Pull f2fs fixes from Jaegeuk Kim:
 o Support swap file and link generic_file_remap_pages
 o Enhance the bio streaming flow and free section control
 o Major bug fix on recovery routine
 o Minor bug/warning fixes and code cleanups

* tag 'f2fs-for-3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (22 commits)
  f2fs: use _safe() version of list_for_each
  f2fs: add comments of start_bidx_of_node
  f2fs: avoid issuing small bios due to several dirty node pages
  f2fs: support swapfile
  f2fs: add remap_pages as generic_file_remap_pages
  f2fs: add __init to functions in init_f2fs_fs
  f2fs: fix the debugfs entry creation path
  f2fs: add global mutex_lock to protect f2fs_stat_list
  f2fs: remove the blk_plug usage in f2fs_write_data_pages
  f2fs: avoid redundant time update for parent directory in f2fs_delete_entry
  f2fs: remove redundant call to set_blocksize in f2fs_fill_super
  f2fs: move f2fs_balance_fs to punch_hole
  f2fs: add f2fs_balance_fs in several interfaces
  f2fs: revisit the f2fs_gc flow
  f2fs: check return value during recovery
  f2fs: avoid null dereference in f2fs_acl_from_disk
  f2fs: initialize newly allocated dnode structure
  f2fs: update f2fs partition info about SIT/NAT layout
  f2fs: update f2fs document to reflect SIT/NAT layout correctly
  f2fs: remove unneeded INIT_LIST_HEAD at few places
  ...

Pull vfio fix from Alex Williamson.
 "vfio-pci: Fix buffer overfill"

* tag 'vfio-for-v3.8-rc5' of git://github.com/awilliam/linux-vfio:
  vfio-pci: Fix buffer overfill

Pull ftrace fix from Steven Rostedt:
 "Kprobes now uses the function tracer if it can.  That is, if a probe
  is placed on a function mcount/nop location, and the arch supports it,
  instead of adding a breakpoint, kprobes will register a function
  callback as that is much more efficient.

  The function tracer requires to update modules before they run, and
  uses the module notifier to do so.  But if something else in the
  module notifiers registers a kprobe at one of these locations, before
  ftrace can get to it, then the system could fail.

  The function tracer must be initialized early, otherwise module
  notifiers that probe will only work by chance."

* tag 'trace-3.8-rc4-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ftrace: Be first to run code modification on modules

Pull libata fixes from Jeff Garzik:

 1) ahci: Fix typo that caused erronenous error handling.

    Thought: I wonder if sparse could have caught this, somehow.

 2) ahci: support a slightly odd Enmotus variant

 3) core: fix a drive detection problem by correcting the logic by which
    the DevSlp timing variables are obtained and used.

* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [libata] replace sata_settings with devslp_timing
  [libata] ahci: Add support for Enmotus Bobcat device.
  [libata] ahci: Fix lack of command retry after a success error handler.

Pull security subsystem bugfixes from James Morris.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  security/device_cgroup: lock assert fails in dev_exception_clean()
  evm: checking if removexattr is not a NULL

wake_up_process() should never wakeup a TASK_STOPPED/TRACED task.
Change it to use TASK_NORMAL and add the WARN_ON().

TASK_ALL has no other users, probably can be killed.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

putreg() assumes that the tracee is not running and pt_regs_access() can
safely play with its stack.  However a killed tracee can return from
ptrace_stop() to the low-level asm code and do RESTORE_REST, this means
that debugger can actually read/modify the kernel stack until the tracee
does SAVE_REST again.

set_task_blockstep() can race with SIGKILL too and in some sense this
race is even worse, the very fact the tracee can be woken up breaks the
logic.

As Linus suggested we can clear TASK_WAKEKILL around the arch_ptrace()
call, this ensures that nobody can ever wakeup the tracee while the
debugger looks at it.  Not only this fixes the mentioned problems, we
can do some cleanups/simplifications in arch_ptrace() paths.

Probably ptrace_unfreeze_traced() needs more callers, for example it
makes sense to make the tracee killable for oom-killer before
access_process_vm().

While at it, add the comment into may_ptrace_stop() to explain why
ptrace_stop() still can't rely on SIGKILL and signal_pending_state().
Reported-by: Salman Qazi <sqazi@google.com>
Reported-by: Suleiman Souhlal <suleiman@google.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Cleanup and preparation for the next change.

signal_wake_up(resume => true) is overused. None of ptrace/jctl callers
actually want to wakeup a TASK_WAKEKILL task, but they can't specify the
necessary mask.

Turn signal_wake_up() into signal_wake_up_state(state), reintroduce
signal_wake_up() as a trivial helper, and add ptrace_signal_wake_up()
which adds __TASK_TRACED.

This way ptrace_signal_wake_up() can work "inside" ptrace_request()
even if the tracee doesn't have the TASK_WAKEKILL bit set.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This is calling list_del() inside a loop which is a problem when we try
move to the next item on the list.  I've converted it to use the _safe
version.  And also, as a cleanup, I've converted it to use
list_for_each_entry instead of list_for_each.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>

The caller of start_bidx_of_node() should give proper node offsets which
point only direct node blocks. Otherwise, it is a caller's bug.
This patch adds comments to make it clear.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>

If some small bios of dirty node pages are supposed to be issued during the
sequential data writes, there-in well-produced consecutive data bios are able
to be split by the small node bios, resulting in performance degradation.
So, let's collect a number of dirty node pages until reaching a threshold.
And, by default, I set the threshold as 2MB, a segment size.

This improves sequential write performance on i5, 512GB SSD (830 w/ SATA2) as
follows.
Before: 231 MB/s -> After: 255 MB/s
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>

This patch adds f2fs_bmap operation to the data address space.
This enables f2fs to support swapfile.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>

This was added for all the file systems before.

See the following commit.

commit id: 0b173bc4

[PATCH] mm: kill vma flag VM_CAN_NONLINEAR

This patch moves actual ptes filling for non-linear file mappings
into special vma operation: ->remap_pages().

File system must implement this method to get non-linear mappings support,
if it uses filemap_fault() then generic_file_remap_pages() can be used.

Now device drivers can implement this method and obtain nonlinear vma support."
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>

Add __init to functions in init_f2fs_fs for code consistency.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>

If some other kernel subsystem has a module notifier, and adds a kprobe
to a ftrace mcount point (now that kprobes work on ftrace points),
when the ftrace notifier runs it will fail and disable ftrace, as well
as kprobes that are attached to ftrace points.

Here's the error:

 WARNING: at kernel/trace/ftrace.c:1618 ftrace_bug+0x239/0x280()
 Hardware name: Bochs
 Modules linked in: fat(+) stap_56d28a51b3fe546293ca0700b10bcb29__8059(F) nfsv4 auth_rpcgss nfs dns_resolver fscache xt_nat iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack lockd sunrpc ppdev parport_pc parport microcode virtio_net i2c_piix4 drm_kms_helper ttm drm i2c_core [last unloaded: bid_shared]
 Pid: 8068, comm: modprobe Tainted: GF            3.7.0-0.rc8.git0.1.fc19.x86_64 #1
 Call Trace:
  [<ffffffff8105e70f>] warn_slowpath_common+0x7f/0xc0
  [<ffffffff81134106>] ? __probe_kernel_read+0x46/0x70
  [<ffffffffa0180000>] ? 0xffffffffa017ffff
  [<ffffffffa0180000>] ? 0xffffffffa017ffff
  [<ffffffff8105e76a>] warn_slowpath_null+0x1a/0x20
  [<ffffffff810fd189>] ftrace_bug+0x239/0x280
  [<ffffffff810fd626>] ftrace_process_locs+0x376/0x520
  [<ffffffff810fefb7>] ftrace_module_notify+0x47/0x50
  [<ffffffff8163912d>] notifier_call_chain+0x4d/0x70
  [<ffffffff810882f8>] __blocking_notifier_call_chain+0x58/0x80
  [<ffffffff81088336>] blocking_notifier_call_chain+0x16/0x20
  [<ffffffff810c2a23>] sys_init_module+0x73/0x220
  [<ffffffff8163d719>] system_call_fastpath+0x16/0x1b
 ---[ end trace 9ef46351e53bbf80 ]---
 ftrace failed to modify [<ffffffffa0180000>] init_once+0x0/0x20 [fat]
  actual: cc:bb:d2:4b:e1

A kprobe was added to the init_once() function in the fat module on load.
But this happened before ftrace could have touched the code. As ftrace
didn't run yet, the kprobe system had no idea it was a ftrace point and
simply added a breakpoint to the code (0xcc in the cc:bb:d2:4b:e1).

Then when ftrace went to modify the location from a call to mcount/fentry
into a nop, it didn't see a call op, but instead it saw the breakpoint op
and not knowing what to do with it, ftrace shut itself down.

The solution is to simply give the ftrace module notifier the max priority.
This should have been done regardless, as the core code ftrace modification
also happens very early on in boot up. This makes the module modification
closer to core modification.

Link: http://lkml.kernel.org/r/20130107140333.593683061@goodmis.org

Cc: stable@vger.kernel.org
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Reported-by: Frank Ch. Eigler <fche@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

These are just compatible with other CX2075x codecs.

Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

devcgroup_css_free() calls dev_exception_clean() without the devcgroup_mutex being locked.

Shutting down a kvm virt was giving me the following trace:

[36280.732764] ------------[ cut here ]------------
[36280.732778] WARNING: at /home/snits/dev/linux/security/device_cgroup.c:172 dev_exception_clean+0xa9/0xc0()
[36280.732782] Hardware name: Studio XPS 8100
[36280.732785] Modules linked in: xt_REDIRECT fuse ebtable_nat ebtables ipt_MASQUERADE iptable_nat nf_nat_ipv4 nf_nat xt_CHECKSUM iptable_mangle bridge stp llc nf_conntrack_ipv4 ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 nf_defrag_ipv4 ip6table_filter it87 hwmon_vid xt_state nf_conntrack ip6_tables snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_intel snd_hda_codec snd_hwdep snd_seq coretemp snd_seq_device crc32c_intel snd_pcm snd_page_alloc snd_timer snd broadcom tg3 serio_raw i7core_edac edac_core ptp pps_core lpc_ich pcspkr mfd_core soundcore microcode i2c_i801 nfsd auth_rpcgss nfs_acl lockd vhost_net sunrpc tun macvtap macvlan kvm_intel kvm uinput binfmt_misc autofs4 usb_storage firewire_ohci firewire_core crc_itu_t radeon drm_kms_helper ttm
[36280.732921] Pid: 933, comm: libvirtd Tainted: G        W    3.8.0-rc3-00307-g4c217de #1
[36280.732922] Call Trace:
[36280.732927]  [<ffffffff81044303>] warn_slowpath_common+0x93/0xc0
[36280.732930]  [<ffffffff8104434a>] warn_slowpath_null+0x1a/0x20
[36280.732932]  [<ffffffff812deaf9>] dev_exception_clean+0xa9/0xc0
[36280.732934]  [<ffffffff812deb2a>] devcgroup_css_free+0x1a/0x30
[36280.732938]  [<ffffffff810ccd76>] cgroup_diput+0x76/0x210
[36280.732941]  [<ffffffff8119eac0>] d_delete+0x120/0x180
[36280.732943]  [<ffffffff81195cff>] vfs_rmdir+0xef/0x130
[36280.732945]  [<ffffffff81195e47>] do_rmdir+0x107/0x1c0
[36280.732949]  [<ffffffff8132d17e>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[36280.732951]  [<ffffffff81198646>] sys_rmdir+0x16/0x20
[36280.732954]  [<ffffffff8173bd82>] system_call_fastpath+0x16/0x1b
[36280.732956] ---[ end trace ca39dced899a7d9f ]---
Signed-off-by: Jerry Snitselaar <jerry.snitselaar@oracle.com>
Cc: stable@kernel.org
Signed-off-by: James Morris <james.l.morris@oracle.com>

The following lines of code produce a kernel oops.

fd = socket(PF_FILE, SOCK_STREAM|SOCK_CLOEXEC|SOCK_NONBLOCK, 0);
fchmod(fd, 0666);

[  139.922364] BUG: unable to handle kernel NULL pointer dereference at   (null)
[  139.924982] IP: [<  (null)>]   (null)
[  139.924982] *pde = 00000000
[  139.924982] Oops: 0000 [#5] SMP
[  139.924982] Modules linked in: fuse dm_crypt dm_mod i2c_piix4 serio_raw evdev binfmt_misc button
[  139.924982] Pid: 3070, comm: acpid Tainted: G      D      3.8.0-rc2-kds+ #465 Bochs Bochs
[  139.924982] EIP: 0060:[<00000000>] EFLAGS: 00010246 CPU: 0
[  139.924982] EIP is at 0x0
[  139.924982] EAX: cf5ef000 EBX: cf5ef000 ECX: c143d600 EDX: c15225f2
[  139.924982] ESI: cf4d2a1c EDI: cf4d2a1c EBP: cc02df10 ESP: cc02dee4
[  139.924982]  DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[  139.924982] CR0: 80050033 CR2: 00000000 CR3: 0c059000 CR4: 000006d0
[  139.924982] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[  139.924982] DR6: ffff0ff0 DR7: 00000400
[  139.924982] Process acpid (pid: 3070, ti=cc02c000 task=d7705340 task.ti=cc02c000)
[  139.924982] Stack:
[  139.924982]  c1203c88 00000000 cc02def4 cf4d2a1c ae21eefa 471b60d5 1083c1ba c26a5940
[  139.924982]  e891fb5e 00000041 00000004 cc02df1c c1203964 00000000 cc02df4c c10e20c3
[  139.924982]  00000002 00000000 00000000 22222222 c1ff2222 cf5ef000 00000000 d76efb08
[  139.924982] Call Trace:
[  139.924982]  [<c1203c88>] ? evm_update_evmxattr+0x5b/0x62
[  139.924982]  [<c1203964>] evm_inode_post_setattr+0x22/0x26
[  139.924982]  [<c10e20c3>] notify_change+0x25f/0x281
[  139.924982]  [<c10cbf56>] chmod_common+0x59/0x76
[  139.924982]  [<c10e27a1>] ? put_unused_fd+0x33/0x33
[  139.924982]  [<c10cca09>] sys_fchmod+0x39/0x5c
[  139.924982]  [<c13f4f30>] syscall_call+0x7/0xb
[  139.924982] Code:  Bad EIP value.

This happens because sockets do not define the removexattr operation.
Before removing the xattr, verify the removexattr function pointer is
not NULL.
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Morris <james.l.morris@oracle.com>

Pull drm fixes from Dave Airlie:
 "A bunch of intel and radeon fixes, along with two fixes to TTM code.

  The correct fix for the Intel ironlake failure is in this, and should
  make things more stable, along with some misc radeon fixes."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  ttm: on move memory failure don't leave a node dangling
  ttm: don't destroy old mm_node on memcpy failure
  Revert "drm/radeon: do not move bo to different placement at each cs"
  drm/i915: fix FORCEWAKE posting reads
  drm/i915: Invalidate the relocation presumed_offsets along the slow path
  drm/i915/eDP: do not write power sequence registers for ghost eDP
  drm/radeon: improve semaphore debugging on lockup
  drm/radeon: allow FP16 color clear registers on r500
  drm/radeon: clear reset flags if engines are idle
  drm/i915: Record DERRMR, FORCEWAKE and RING_CTL in error-state

Commit 1fb9341a ("module: put modules in list much earlier") moved
some of the module initialization code around, and in the process
changed the exit paths too.  But for the duplicate export symbol error
case the change made the ddebug_cleanup path jump to after the module
mutex unlock, even though it happens with the mutex held.

Rusty has some patches to split this function up into some helper
functions, hopefully the mess of complex goto targets will go away
eventually.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

if we have a move notify callback, when moving fails, we call move notify
the opposite way around, however this ends up with *mem containing the mm_node
from the bo, which means we double free it. This is a follow on to the previous
fix.
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

When we are using memcpy to move objects around, and we fail to memcpy
due to lack of memory to populate or failure to finish the copy, we don't
want to destroy the mm_node that has been copied into old_copy.

While working on a new kms driver that uses memcpy, if I overallocated bo's
up to the memory limits, and eviction failed, then machine would oops soon
after due to having an active bo with an already freed drm_mm embedded in it,
freeing it a second time didn't end well.
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

More important fixes for 3.9:
- error_state improvements to help debug the new scanline wait code added
  for gen6+ - bug reports started popping up :( patch from Chris Wilson.
- fix a panel power sequence confusion between the eDP and lvds detection
  code resulting in black screens - regression introduce in 3.8 (Jani
  Nikula)
- Chris fixed the root-cause of the ilk relocation vs. evict bug.
- Another piece of cargo-culted rc6 lore from Jani, fixes up a regression
  where a system refused to go into rc6 after suspend sometimes.

* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
  drm/i915: fix FORCEWAKE posting reads
  drm/i915: Invalidate the relocation presumed_offsets along the slow path
  drm/i915/eDP: do not write power sequence registers for ghost eDP
  drm/i915: Record DERRMR, FORCEWAKE and RING_CTL in error-state

A number of fixes, and one revert for a patch having some wierd side effects.

* 'drm-fixes-3.8' of git://people.freedesktop.org/~agd5f/linux:
  Revert "drm/radeon: do not move bo to different placement at each cs"
  drm/radeon: improve semaphore debugging on lockup
  drm/radeon: allow FP16 color clear registers on r500
  drm/radeon: clear reset flags if engines are idle

Pull module fixes and a virtio block fix from Rusty Russell:
 "Various minor fixes, but a slightly more complex one to fix the
  per-cpu overload problem introduced recently by kvm id changes."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
  module: put modules in list much earlier.
  module: add new state MODULE_STATE_UNFORMED.
  module: prevent warning when finit_module a 0 sized file
  virtio-blk: Don't free ida when disk is in use

Pull misc syscall fixes from Al Viro:

 - compat syscall fixes (discussed back in December)

 - a couple of "make life easier for sigaltstack stuff by reducing
   inter-tree dependencies"

 - fix up compiler/asmlinkage calling convention disagreement of
   sys_clone()

 - misc

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
  sys_clone() needs asmlinkage_protect
  make sure that /linuxrc has std{in,out,err}
  x32: fix sigtimedwait
  x32: fix waitid()
  switch compat_sys_wait4() and compat_sys_waitid() to COMPAT_SYSCALL_DEFINE
  switch compat_sys_sigaltstack() to COMPAT_SYSCALL_DEFINE
  CONFIG_GENERIC_SIGALTSTACK build breakage with asm-generic/syscalls.h
  Ensure that kernel_init_freeable() is not inlined into non __init code

The ia64 function "thread_matches()" has no users since commit
e868a55c ("[IA64] remove find_thread_for_addr()").  Remove it.

This allows us to make ptrace_check_attach() static to kernel/ptrace.c,
which is good since we'll need to change the semantics of it and fix up
all the callers.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Acer AO725 needs the same fixup as AO756.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=52181Signed-off-by: Takashi Iwai <tiwai@suse.de>

Pull USB fixes from Greg Kroah-Hartman:
 "Here are 3 USB patches for 3.8-rc4.  Two of them are new device id
  patches, and the third fixes a reported oops in the io_ti USB serial
  driver"

* tag 'usb-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: io_ti: Fix NULL dereference in chase_port()
  USB: option: add TP-LINK HSUPA Modem MA180
  USB: option: blacklist network interface on ONDA MT8205 4G LTE