- 26 Jul, 2019 40 commits
-
-
liaoweixiong authored
commit b83408b5 upstream. In case of the last page containing bitflips (ret > 0), spinand_mtd_read() will return that number of bitflips for the last page while it should instead return max_bitflips like it does when the last page read returns with 0. Signed-off-by:
Weixiong Liao <liaoweixiong@allwinnertech.com> Reviewed-by:
Boris Brezillon <boris.brezillon@collabora.com> Reviewed-by:
Frieder Schrempf <frieder.schrempf@kontron.de> Cc: stable@vger.kernel.org Fixes: 7529df46 ("mtd: nand: Add core infrastructure to support SPI NANDs") Signed-off-by:
Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Xiaolei Li authored
commit e1884ffd upstream. At present, the flow of calculating AC timing of read/write cycle in SDR mode is that: At first, calculate high hold time which is valid for both read and write cycle using the max value between tREH_min and tWH_min. Secondly, calculate WE# pulse width using tWP_min. Thridly, calculate RE# pulse width using the bigger one between tREA_max and tRP_min. But NAND SPEC shows that Controller should also meet write/read cycle time. That is write cycle time should be more than tWC_min and read cycle should be more than tRC_min. Obviously, we do not achieve that now. This patch corrects the low level time calculation to meet minimum read/write cycle time required. After getting the high hold time, WE# low level time will be promised to meet tWP_min and tWC_min requirement, and RE# low level time will be promised to meet tREA_max, tRP_min and tRC_min requirement. Fixes: edfee361 ("mtd: nand: mtk: add ->setup_data_interface() hook") Cc: stable@vger.kernel.org # v4.17+ Signed-off-by:
Xiaolei Li <xiaolei.li@mediatek.com> Reviewed-by:
-
Dan Carpenter authored
commit 0bdf8a82 upstream. ECRYPTFS_SIZE_AND_MARKER_BYTES is type size_t, so if "rc" is negative that gets type promoted to a high positive value and treated as success. Fixes: 778aeb42 ("eCryptfs: Cleanup and optimize ecryptfs_lookup_interpose()") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> [tyhicks: Use "if/else if" rather than "if/if"] Cc: stable@vger.kernel.org Signed-off-by:
Tyler Hicks <tyhicks@canonical.com> Signed-off-by:
-
Jorge Ramirez-Ortiz authored
commit 5e6b6651 upstream. mutexes can sleep and therefore should not be taken while holding a spinlock. move clk_get_rate (can sleep) outside the spinlock protected region. Fixes: 83736352 ("mmc: sdhci-msm: Update DLL reset sequence") Cc: stable@vger.kernel.org Signed-off-by:
Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org> Reviewed-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by:
Vinod Koul <vkoul@kernel.org> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Nathan Lynch authored
commit 0aa82c48 upstream. During post-migration device tree updates, we can oops in pseries_update_drconf_memory() if the source device tree has an ibm,dynamic-memory-v2 property and the destination has a ibm,dynamic_memory (v1) property. The notifier processes an "update" for the ibm,dynamic-memory property but it's really an add in this scenario. So make sure the old property object is there before dereferencing it. Fixes: 2b31e3ae ("powerpc/drmem: Add support for ibm, dynamic-memory-v2 property") Cc: stable@vger.kernel.org # v4.16+ Signed-off-by:
Nathan Lynch <nathanl@linux.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Alexey Kardashevskiy authored
commit 5636427d upstream. The powernv platform uses @dma_iommu_ops for non-bypass DMA. These ops need an iommu_table pointer which is stored in dev->archdata.iommu_table_base. It is initialized during pcibios_setup_device() which handles boot time devices. However when a device is taken from the system in order to pass it through, the default IOMMU table is destroyed but the pointer in a device is not updated; also when a device is returned back to the system, a new table pointer is not stored in dev->archdata.iommu_table_base either. So when a just returned device tries using IOMMU, it crashes on accessing stale iommu_table or its members. This calls set_iommu_table_base() when the default window is created. Note it used to be there before but was wrongly removed (see "fixes"). It did not appear before as these days most devices simply use bypass. This adds set_iommu_table_base(NULL) when a device is taken from the system to make it clear that IOMMU DMA cannot be used past that point. Fixes: c4e9d3c1 ("powerpc/powernv/pseries: Rework device adding to IOMMU groups") Cc: stable@vger.kernel.org # v5.0+ Signed-off-by:
Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by:
-
Greg Kurz authored
commit 02c5f539 upstream. Since 902bdc57, get_pci_dev() calls pci_get_domain_bus_and_slot(). This has the effect of incrementing the reference count of the PCI device, as explained in drivers/pci/search.c: * Given a PCI domain, bus, and slot/function number, the desired PCI * device is located in the list of PCI devices. If the device is * found, its reference count is increased and this function returns a * pointer to its data structure. The caller must decrement the * reference count by calling pci_dev_put(). If no device is found, * %NULL is returned. Nothing was done to call pci_dev_put() and the reference count of GPU and NPU PCI devices rockets up. A natural way to fix this would be to teach the callers about the change, so that they call pci_dev_put() when done with the pointer. This turns out to be quite intrusive, as it affects many paths in npu-dma.c, pci-ioda.c and vfio_pci_nvlink2.c. Also, the issue appeared in 4.16 and some affected code got moved around since then: it would be problematic to backport the fix to stable releases. All that code never cared for reference counting anyway. Call pci_dev_put() from get_pci_dev() to revert to the previous behavior. Fixes: 902bdc57 ("powerpc/powernv/idoa: Remove unnecessary pcidev from pci_dn") Cc: stable@vger.kernel.org # v4.16 Signed-off-by:
Greg Kurz <groug@kaod.org> Reviewed-by:
-
Ravi Bangoria authored
commit f474c28f upstream. powerpc hardware triggers watchpoint before executing the instruction. To make trigger-after-execute behavior, kernel emulates the instruction. If the instruction is 'load something into non-volatile register', exception handler should restore emulated register state while returning back, otherwise there will be register state corruption. eg, adding a watchpoint on a list can corrput the list: # cat /proc/kallsyms | grep kthread_create_list c00000000121c8b8 d kthread_create_list Add watchpoint on kthread_create_list->prev: # perf record -e mem:0xc00000000121c8c0 Run some workload such that new kthread gets invoked. eg, I just logged out from console: list_add corruption. next->prev should be prev (c000000001214e00), \ but was c00000000121c8b8. (next=c00000000121c8b8). WARNING: CPU: 59 PID: 309 at lib/list_debug.c:25 __list_add_valid+0xb4/0xc0 CPU: 59 PID: 309 Comm: kworker/59:0 Kdump: loaded Not tainted 5.1.0-rc7+ #69 ... NIP __list_add_valid+0xb4/0xc0 LR __list_add_valid+0xb0/0xc0 Call Trace: __list_add_valid+0xb0/0xc0 (unreliable) __kthread_create_on_node+0xe0/0x260 kthread_create_on_node+0x34/0x50 create_worker+0xe8/0x260 worker_thread+0x444/0x560 kthread+0x160/0x1a0 ret_from_kernel_thread+0x5c/0x70 List corruption happened because it uses 'load into non-volatile register' instruction: Snippet from __kthread_create_on_node: c000000000136be8: addis r29,r2,-19 c000000000136bec: ld r29,31424(r29) if (!__list_add_valid(new, prev, next)) c000000000136bf0: mr r3,r30 c000000000136bf4: mr r5,r28 c000000000136bf8: mr r4,r29 c000000000136bfc: bl c00000000059a2f8 <__list_add_valid+0x8> Register state from WARN_ON(): GPR00: c00000000059a3a0 c000007ff23afb50 c000000001344e00 0000000000000075 GPR04: 0000000000000000 0000000000000000 0000001852af8bc1 0000000000000000 GPR08: 0000000000000001 0000000000000007 0000000000000006 00000000000004aa GPR12: 0000000000000000 c000007ffffeb080 c000000000137038 c000005ff62aaa00 GPR16: 0000000000000000 0000000000000000 c000007fffbe7600 c000007fffbe7370 GPR20: c000007fffbe7320 c000007fffbe7300 c000000001373a00 0000000000000000 GPR24: fffffffffffffef7 c00000000012e320 c000007ff23afcb0 c000000000cb8628 GPR28: c00000000121c8b8 c000000001214e00 c000007fef5b17e8 c000007fef5b17c0 Watchpoint hit at 0xc000000000136bec. addis r29,r2,-19 => r29 = 0xc000000001344e00 + (-19 << 16) => r29 = 0xc000000001214e00 ld r29,31424(r29) => r29 = *(0xc000000001214e00 + 31424) => r29 = *(0xc00000000121c8c0) 0xc00000000121c8c0 is where we placed a watchpoint and thus this instruction was emulated by emulate_step. But because handle_dabr_fault did not restore emulated register state, r29 still contains stale value in above register state. Fixes: 5aae8a53 ("powerpc, hw_breakpoints: Implement hw_breakpoints for 64-bit server processors") Signed-off-by:
Ravi Bangoria <ravi.bangoria@linux.ibm.com> Cc: stable@vger.kernel.org # 2.6.36+ Signed-off-by:
-
Andreas Schwab authored
commit 46c2478a upstream. Move a misplaced paren that makes the condition always true. Fixes: 63b2bc61 ("powerpc/mm/32s: Use BATs for STRICT_KERNEL_RWX") Cc: stable@vger.kernel.org # v5.1+ Signed-off-by:
Andreas Schwab <schwab@linux-m68k.org> Reviewed-by:
Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by:
-
Christophe Leroy authored
commit 6ecb78ef upstream. Previously, only IBAT1 and IBAT2 were used to map kernel linear mem. Since commit 63b2bc61 ("powerpc/mm/32s: Use BATs for STRICT_KERNEL_RWX"), we may have all 8 BATs used for mapping kernel text. But the suspend/restore functions only save/restore BATs 0 to 3, and clears BATs 4 to 7. Make suspend and restore functions respectively save and reload the 8 BATs on CPUs having MMU_FTR_USE_HIGH_BATS feature. Reported-by:
-
Helge Deller authored
commit 10835c85 upstream. On parisc the privilege level of a process is stored in the lowest two bits of the instruction pointers (IAOQ0 and IAOQ1). On Linux we use privilege level 0 for the kernel and privilege level 3 for user-space. So userspace should not be allowed to modify IAOQ0 or IAOQ1 of a ptraced process to change it's privilege level to e.g. 0 to try to gain kernel privileges. This patch prevents such modifications by always setting the two lowest bits to one (which relates to privilege level 3 for user-space) if IAOQ0 or IAOQ1 are modified via ptrace calls in the native and compat ptrace paths. Link: https://bugs.gentoo.org/481768Reported-by:
Jeroen Roovers <jer@gentoo.org> Cc: <stable@vger.kernel.org> Tested-by:
Rolf Eike Beer <eike-kernel@sf-tec.de> Signed-off-by:
Helge Deller <deller@gmx.de> Signed-off-by:
-
Helge Deller authored
commit 34c32fc6 upstream. On parisc the privilege level of a process is stored in the lowest two bits of the instruction pointers (IAOQ0 and IAOQ1). On Linux we use privilege level 0 for the kernel and privilege level 3 for user-space. So userspace should not be allowed to modify IAOQ0 or IAOQ1 of a ptraced process to change it's privilege level to e.g. 0 to try to gain kernel privileges. This patch prevents such modifications in the regset support functions by always setting the two lowest bits to one (which relates to privilege level 3 for user-space) if IAOQ0 or IAOQ1 are modified via ptrace regset calls. Link: https://bugs.gentoo.org/481768 Cc: <stable@vger.kernel.org> # v4.7+ Tested-by:
-
Steve Longerbeam authored
commit 3d1f62c6 upstream. The saturation bit was being set at bit 9 in the second 32-bit word of the TPMEM CSC. This isn't correct, the saturation bit is bit 42, which is bit 10 of the second word. Fixes: 1aa8ea0d ("gpu: ipu-v3: Add Image Converter unit") Signed-off-by:
Steve Longerbeam <slongerbeam@gmail.com> Reviewed-by:
Philipp Zabel <p.zabel@pengutronix.de> Cc: stable@vger.kernel.org Signed-off-by:
-
Darrick J. Wong authored
[ Upstream commit 1fdeaea4 ] Dave Chinner noticed that xfs_file_dio_aio_write returns EAGAIN without dropping the IOLOCK when its deciding not to wait, which means that we leak the IOLOCK there. Since we now make unaligned directio always wait, we have the opportunity to bail out before trying to take the lock, which should reduce the overhead of this never-gonna-work case considerably while also solving the dropped lock problem. Reported-by:
Dave Chinner <david@fromorbit.com> Signed-off-by:
Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by:
Brian Foster <bfoster@redhat.com> Reviewed-by:
Dave Chinner <dchinner@redhat.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Nadav Amit authored
commit 49f17c26 upstream. Since resources can be removed, locking should ensure that the resource is not removed while accessing it. However, find_next_iomem_res() does not hold the lock while copying the data of the resource. Keep holding the lock while the data is copied. While at it, change the return value to a more informative value. It is disregarded by the callers. [akpm@linux-foundation.org: fix find_next_iomem_res() documentation] Link: http://lkml.kernel.org/r/20190613045903.4922-2-namit@vmware.com Fixes: ff3cc952 ("resource: Add remove_resource interface") Signed-off-by:
Nadav Amit <namit@vmware.com> Reviewed-by:
Andrew Morton <akpm@linux-foundation.org> Reviewed-by:
Dan Williams <dan.j.williams@intel.com> Cc: Borislav Petkov <bp@suse.de> Cc: Toshi Kani <toshi.kani@hpe.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Drew Davenport authored
commit 6b15f678 upstream. For architectures using __WARN_TAINT, the WARN_ON macro did not print out the "cut here" string. The other WARN_XXX macros would print "cut here" inside __warn_printk, which is not called for WARN_ON since it doesn't have a message to print. Link: http://lkml.kernel.org/r/20190624154831.163888-1-ddavenport@chromium.org Fixes: a7bed27a ("bug: fix "cut here" location for __WARN_TAINT architectures") Signed-off-by:
Drew Davenport <ddavenport@chromium.org> Acked-by:
Kees Cook <keescook@chromium.org> Tested-by:
-
Jan Harkes authored
commit 7fa0a1da upstream. Patch series "Coda updates". The following patch series is a collection of various fixes for Coda, most of which were collected from linux-fsdevel or linux-kernel but which have as yet not found their way upstream. This patch (of 22): Various file systems expect that vma->vm_file points at their own file handle, several use file_inode(vma->vm_file) to get at their inode or use vma->vm_file->private_data. However the way Coda wrapped mmap on a host file broke this assumption, vm_file was still pointing at the Coda file and the host file systems would scribble over Coda's inode and private file data. This patch fixes the incorrect expectation and wraps vm_ops->open and vm_ops->close to allow Coda to track when the vm_area_struct is destroyed so we still release the reference on the Coda file handle at the right time. Link: http://lkml.kernel.org/r/0e850c6e59c0b147dc2dcd51a3af004c948c3697.1558117389.git.jaharkes@cs.cmu.eduSigned-off-by:
Jan Harkes <jaharkes@cs.cmu.edu> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Colin Ian King <colin.king@canonical.com> Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: David Howells <dhowells@redhat.com> Cc: Fabian Frederick <fabf@skynet.be> Cc: Mikko Rapeli <mikko.rapeli@iki.fi> Cc: Sam Protsenko <semen.protsenko@linaro.org> Cc: Yann Droneaud <ydroneaud@opteya.com> Cc: Zhouyang Jia <jiazhouyang09@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Dan Williams authored
commit 7e3e888d upstream. At namespace creation time there is the potential for the "expected to be zero" fields of a 'pfn' info-block to be filled with indeterminate data. While the kernel buffer is zeroed on allocation it is immediately overwritten by nd_pfn_validate() filling it with the current contents of the on-media info-block location. For fields like, 'flags' and the 'padding' it potentially means that future implementations can not rely on those fields being zero. In preparation to stop using the 'start_pad' and 'end_trunc' fields for section alignment, arrange for fields that are not explicitly initialized to be guaranteed zero. Bump the minor version to indicate it is safe to assume the 'padding' and 'flags' are zero. Otherwise, this corruption is expected to benign since all other critical fields are explicitly initialized. Note The cc: stable is about spreading this new policy to as many kernels as possible not fixing an issue in those kernels. It is not until the change titled "libnvdimm/pfn: Stop padding pmem namespaces to section alignment" where this improper initialization becomes a problem. So if someone decides to backport "libnvdimm/pfn: Stop padding pmem namespaces to section alignment" (which is not tagged for stable), make sure this pre-requisite is flagged. Link: http://lkml.kernel.org/r/156092356065.979959.6681003754765958296.stgit@dwillia2-desk3.amr.corp.intel.com Fixes: 32ab0a3f ("libnvdimm, pmem: 'struct page' for pmem") Signed-off-by:
-
Aneesh Kumar K.V authored
commit 9bd3bb67 upstream. Architectures like powerpc use different address range to map ioremap and vmalloc range. The memunmap() check used by the nvdimm layer was wrongly using is_vmalloc_addr() to check for ioremap range which fails for ppc64. This result in ppc64 not freeing the ioremap mapping. The side effect of this is an unbind failure during module unload with papr_scm nvdimm driver Link: http://lkml.kernel.org/r/20190701134038.14165-1-aneesh.kumar@linux.ibm.comSigned-off-by:
Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Fixes: b5beae5e ("powerpc/pseries: Add driver for PAPR SCM regions") Cc: Dan Williams <dan.j.williams@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Aaron Armstrong Skomra authored
commit 68c20cc2 upstream. This affects the 2nd-gen Intuos Pro Medium and Large when using their Bluetooth connection. Fixes: 4922cd26 ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface") Cc: <stable@vger.kernel.org> # v4.11+ Signed-off-by:
Aaron Armstrong Skomra <aaron.skomra@wacom.com> Reviewed-by:
Jason Gerecke <jason.gerecke@wacom.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Aaron Armstrong Skomra authored
commit d4b8efeb upstream. Only sync the pad once per report, not once per collection. Also avoid syncing the pad on battery reports. Fixes: f8b6a747 ("HID: wacom: generic: Support multiple tools per report") Cc: <stable@vger.kernel.org> # v4.17+ Signed-off-by:
-
Aaron Armstrong Skomra authored
commit d8e98060 upstream. Currently, the driver will attempt to set the mode on all devices with a center button, but some devices with a center button lack LEDs, and attempting to set the LEDs on devices without LEDs results in the kernel error message of the form: "leds input8::wacom-0.1: Setting an LED's brightness failed (-32)" This is because the generic codepath erroneously assumes that the BUTTON_CENTER usage indicates that the device has LEDs, the previously ignored TOUCH_RING_SETTING usage is a more accurate indication of the existence of LEDs on the device. Fixes: 10c55cac ("HID: wacom: generic: support LEDs") Cc: <stable@vger.kernel.org> # v4.11+ Signed-off-by:
-
Danit Goldberg authored
commit 89705e92 upstream. Userspace expects the IB_TM_CAP_RC bit to indicate that the device supports RC transport tag matching with rendezvous offload. However the firmware splits this into two capabilities for eager and rendezvous tag matching. Only if the FW supports both modes should userspace be told the tag matching capability is available. Cc: <stable@vger.kernel.org> # 4.13 Fixes: eb761894 ("IB/mlx5: Fill XRQ capabilities") Signed-off-by:
Danit Goldberg <danitg@mellanox.com> Reviewed-by:
Yishai Hadas <yishaih@mellanox.com> Reviewed-by:
Artemy Kovalyov <artemyko@mellanox.com> Signed-off-by:
Leon Romanovsky <leonro@mellanox.com> Signed-off-by:
Jason Gunthorpe <jgg@mellanox.com> Signed-off-by:
-
Filipe Manana authored
commit 17900668 upstream. If the range for which we are punching a hole covers only part of a page, we end up updating the inode item but we skip the update of the inode's iversion, mtime and ctime. Fix that by ensuring we update those properties of the inode. A patch for fstests test case generic/059 that tests this as been sent along with this fix. Fixes: 2aaa6655 ("Btrfs: add hole punching") Fixes: e8c1c76e ("Btrfs: add missing inode update when punching hole") CC: stable@vger.kernel.org # 4.4+ Signed-off-by:
Filipe Manana <fdmanana@suse.com> Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
Filipe Manana authored
commit 803f0f64 upstream. In order to avoid searches on a log tree when unlinking an inode, we check if the inode being unlinked was logged in the current transaction, as well as the inode of its parent directory. When any of the inodes are logged, we proceed to delete directory items and inode reference items from the log, to ensure that if a subsequent fsync of only the inode being unlinked or only of the parent directory when the other is not fsync'ed as well, does not result in the entry still existing after a power failure. That check however is not reliable when one of the inodes involved (the one being unlinked or its parent directory's inode) is evicted, since the logged_trans field is transient, that is, it is not stored on disk, so it is lost when the inode is evicted and loaded into memory again (which is set to zero on load). As a consequence the checks currently being done by btrfs_del_dir_entries_in_log() and btrfs_del_inode_ref_in_log() always return true if the inode was evicted before, regardless of the inode having been logged or not before (and in the current transaction), this results in the dentry being unlinked still existing after a log replay if after the unlink operation only one of the inodes involved is fsync'ed. Example: $ mkfs.btrfs -f /dev/sdb $ mount /dev/sdb /mnt $ mkdir /mnt/dir $ touch /mnt/dir/foo $ xfs_io -c fsync /mnt/dir/foo # Keep an open file descriptor on our directory while we evict inodes. # We just want to evict the file's inode, the directory's inode must not # be evicted. $ ( cd /mnt/dir; while true; do :; done ) & $ pid=$! # Wait a bit to give time to background process to chdir to our test # directory. $ sleep 0.5 # Trigger eviction of the file's inode. $ echo 2 > /proc/sys/vm/drop_caches # Unlink our file and fsync the parent directory. After a power failure # we don't expect to see the file anymore, since we fsync'ed the parent # directory. $ rm -f $SCRATCH_MNT/dir/foo $ xfs_io -c fsync /mnt/dir <power failure> $ mount /dev/sdb /mnt $ ls /mnt/dir foo $ --> file still there, unlink not persisted despite explicit fsync on dir Fix this by checking if the inode has the full_sync bit set in its runtime flags as well, since that bit is set everytime an inode is loaded from disk, or for other less common cases such as after a shrinking truncate or failure to allocate extent maps for holes, and gets cleared after the first fsync. Also consider the inode as possibly logged only if it was last modified in the current transaction (besides having the full_fsync flag set). Fixes: 3a5f1d45 ("Btrfs: Optimize btree walking while logging inodes") CC: stable@vger.kernel.org # 4.4+ Signed-off-by:
-
Filipe Manana authored
commit d1d832a0 upstream. When we log an inode, regardless of logging it completely or only that it exists, we always update it as logged (logged_trans and last_log_commit fields of the inode are updated). This is generally fine and avoids future attempts to log it from having to do repeated work that brings no value. However, if we write data to a file, then evict its inode after all the dealloc was flushed (and ordered extents completed), rename the file and fsync it, we end up not logging the new extents, since the rename may result in logging that the inode exists in case the parent directory was logged before. The following reproducer shows and explains how this can happen: $ mkfs.btrfs -f /dev/sdb $ mount /dev/sdb /mnt $ mkdir /mnt/dir $ touch /mnt/dir/foo $ touch /mnt/dir/bar # Do a direct IO write instead of a buffered write because with a # buffered write we would need to make sure dealloc gets flushed and # complete before we do the inode eviction later, and we can not do that # from user space with call to things such as sync(2) since that results # in a transaction commit as well. $ xfs_io -d -c "pwrite -S 0xd3 0 4K" /mnt/dir/bar # Keep the directory dir in use while we evict inodes. We want our file # bar's inode to be evicted but we don't want our directory's inode to # be evicted (if it were evicted too, we would not be able to reproduce # the issue since the first fsync below, of file foo, would result in a # transaction commit. $ ( cd /mnt/dir; while true; do :; done ) & $ pid=$! # Wait a bit to give time for the background process to chdir. $ sleep 0.1 # Evict all inodes, except the inode for the directory dir because it is # currently in use by our background process. $ echo 2 > /proc/sys/vm/drop_caches # fsync file foo, which ends up persisting information about the parent # directory because it is a new inode. $ xfs_io -c fsync /mnt/dir/foo # Rename bar, this results in logging that this inode exists (inode item, # names, xattrs) because the parent directory is in the log. $ mv /mnt/dir/bar /mnt/dir/baz # Now fsync baz, which ends up doing absolutely nothing because of the # rename operation which logged that the inode exists only. $ xfs_io -c fsync /mnt/dir/baz <power failure> $ mount /dev/sdb /mnt $ od -t x1 -A d /mnt/dir/baz 0000000 --> Empty file, data we wrote is missing. Fix this by not updating last_sub_trans of an inode when we are logging only that it exists and the inode was not yet logged since it was loaded from disk (full_sync bit set), this is enough to make btrfs_inode_in_log() return false for this scenario and make us log the inode. The logged_trans of the inode is still always setsince that alone is used to track if names need to be deleted as part of unlink operations. Fixes: 257c62e1 ("Btrfs: avoid tree log commit when there are no changes") CC: stable@vger.kernel.org # 4.4+ Signed-off-by:
-
Niklas Cassel authored
commit 64adde31 upstream. Currently, there is only a 1 ms sleep after asserting PERST. Reading the datasheets for different endpoints, some require PERST to be asserted for 10 ms in order for the endpoint to perform a reset, others require it to be asserted for 50 ms. Several SoCs using this driver uses PCIe Mini Card, where we don't know what endpoint will be plugged in. The PCI Express Card Electromechanical Specification r2.0, section 2.2, "PERST# Signal" specifies: "On power up, the deassertion of PERST# is delayed 100 ms (TPVPERL) from the power rails achieving specified operating limits." Add a sleep of 100 ms before deasserting PERST, in order to ensure that we are compliant with the spec. Fixes: 82a82383 ("PCI: qcom: Add Qualcomm PCIe controller driver") Signed-off-by:
Niklas Cassel <niklas.cassel@linaro.org> Signed-off-by:
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by:
Stanimir Varbanov <svarbanov@mm-sol.com> Cc: stable@vger.kernel.org # 4.5+ Signed-off-by:
-
Mika Westerberg authored
commit 000dd531 upstream. PME polling does not take into account that a device that is directly connected to the host bridge may go into D3cold as well. This leads to a situation where the PME poll thread reads from a config space of a device that is in D3cold and gets incorrect information because the config space is not accessible. Here is an example from Intel Ice Lake system where two PCIe root ports are in D3cold (I've instrumented the kernel to log the PMCSR register contents): [ 62.971442] pcieport 0000:00:07.1: Check PME status, PMCSR=0xffff [ 62.971504] pcieport 0000:00:07.0: Check PME status, PMCSR=0xffff Since 0xffff is interpreted so that PME is pending, the root ports will be runtime resumed. This repeats over and over again essentially blocking all runtime power management. Prevent this from happening by checking whether the device is in D3cold before its PME status is read. Fixes: 71a83bd7 ("PCI/PM: add runtime PM support to PCIe port") Signed-off-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by:
Lukas Wunner <lukas@wunner.de> Cc: 3.6+ <stable@vger.kernel.org> # v3.6+ Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Dexuan Cui authored
commit 4df591b2 upstream. Fix a use-after-free in hv_eject_device_work(). Fixes: 05f151a7 ("PCI: hv: Fix a memory leak in hv_eject_device_work()") Signed-off-by:
Dexuan Cui <decui@microsoft.com> Signed-off-by:
Michael Kelley <mikelley@microsoft.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Alexander Shishkin authored
commit 4aa5aed2 upstream. This adds Ice Lake NNPI support to the Intel(R) Trace Hub. Signed-off-by:
Alexander Shishkin <alexander.shishkin@linux.intel.com> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190621161930.60785-5-alexander.shishkin@linux.intel.comSigned-off-by:
-
Bart Van Assche authored
commit bcef5b72 upstream. The function srp_parse_in() is used both for parsing source address specifications and for target address specifications. Target addresses must have a port number. Having to specify a port number for source addresses is inconvenient. Make sure that srp_parse_in() supports again parsing addresses with no port number. Cc: <stable@vger.kernel.org> Fixes: c62adb7d ("IB/srp: Fix IPv6 address parsing") Signed-off-by:
Bart Van Assche <bvanassche@acm.org> Signed-off-by:
-
Damien Le Moal authored
commit 113ab72e upstream. For large values of the number of zones reported and/or large zone sizes, the sector increment calculated with blk_queue_zone_sectors(q) * n in blk_report_zones() loop can overflow the unsigned int type used for the calculation as both "n" and blk_queue_zone_sectors() value are unsigned int. E.g. for a device with 256 MB zones (524288 sectors), overflow happens with 8192 or more zones reported. Changing the return type of blk_queue_zone_sectors() to sector_t, fixes this problem and avoids overflow problem for all other callers of this helper too. The same change is also applied to the bdev_zone_sectors() helper. Fixes: e76239a3 ("block: add a report_zones method") Cc: stable@vger.kernel.org Signed-off-by:
Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Damien Le Moal authored
commit b4c5875d upstream. To allow the SCSI subsystem scsi_execute_req() function to issue requests using large buffers that are better allocated with vmalloc() rather than kmalloc(), modify bio_map_kern() to allow passing a buffer allocated with vmalloc(). To do so, detect vmalloc-ed buffers using is_vmalloc_addr(). For vmalloc-ed buffers, flush the buffer using flush_kernel_vmap_range(), use vmalloc_to_page() instead of virt_to_page() to obtain the pages of the buffer, and invalidate the buffer addresses with invalidate_kernel_vmap_range() on completion of read BIOs. This last point is executed using the function bio_invalidate_vmalloc_pages() which is defined only if the architecture defines ARCH_HAS_FLUSH_KERNEL_DCACHE_PAGE, that is, if the architecture actually needs the invalidation done. Fixes: 515ce606 ("scsi: sd_zbc: Fix sd_zbc_report_zones() buffer allocation") Fixes: e76239a3 ("block: add a report_zones method") Cc: stable@vger.kernel.org Reviewed-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Reviewed-by:
Ming Lei <ming.lei@redhat.com> Signed-off-by:
-
Andres Rodriguez authored
commit e28ad544 upstream. DisplayID blocks allow embedding of CEA blocks. The payloads are identical to traditional top level CEA extension blocks, but the header is slightly different. This change allows the CEA parser to find a CEA block inside a DisplayID block. Additionally, it adds support for parsing the embedded CTA header. No further changes are necessary due to payload parity. This change fixes audio support for the Valve Index HMD. Signed-off-by:
Andres Rodriguez <andresx7@gmail.com> Reviewed-by:
Dave Airlie <airlied@redhat.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: <stable@vger.kernel.org> # v4.15 Signed-off-by:
-
Kim Phillips authored
commit 2f217d58 upstream. Fill in the L3 performance event select register ThreadMask bitfield, to enable per hardware thread accounting. Signed-off-by:
Kim Phillips <kim.phillips@amd.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: <stable@vger.kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Gary Hook <Gary.Hook@amd.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Martin Liska <mliska@suse.cz> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Pu Wen <puwen@hygon.cn> Cc: Stephane Eranian <eranian@google.com> Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Link: https://lkml.kernel.org/r/20190628215906.4276-2-kim.phillips@amd.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Kim Phillips authored
commit 16f46411 upstream. The following commit: d7cbbe49 ("perf/x86/amd/uncore: Set ThreadMask and SliceMask for L3 Cache perf events") enables L3 PMC events for all threads and slices by writing 1's in 'ChL3PmcCfg' (L3 PMC PERF_CTL) register fields. Those bitfields overlap with high order event select bits in the Data Fabric PMC control register, however. So when a user requests raw Data Fabric events (-e amd_df/event=0xYYY/), the two highest order bits get inadvertently set, changing the counter select to events that don't exist, and for which no counts are read. This patch changes the logic to write the L3 masks only when dealing with L3 PMC counters. AMD Family 16h and below Northbridge (NB) counters were not affected. Signed-off-by:
-
Kan Liang authored
commit e4557c1a upstream. If a user first sample a PEBS event on a fixed counter, then sample a non-PEBS event on the same fixed counter on Icelake, it will trigger spurious NMI. For example: perf record -e 'cycles:p' -a perf record -e 'cycles' -a The error message for spurious NMI: [June 21 15:38] Uhhuh. NMI received for unknown reason 30 on CPU 2. [ +0.000000] Do you have a strange power saving mode enabled? [ +0.000000] Dazed and confused, but trying to continue The bug was introduced by the following commit: commit 6f55967a ("perf/x86/intel: Fix race in intel_pmu_disable_event()") The commit moves the intel_pmu_pebs_disable() after intel_pmu_disable_fixed(), which returns immediately. The related bit of PEBS_ENABLE MSR will never be cleared for the fixed counter. Then a non-PEBS event runs on the fixed counter, but the bit on PEBS_ENABLE is still set, which triggers spurious NMIs. Check and disable PEBS for fixed counters after intel_pmu_disable_fixed(). Reported-by:
Yi, Ammy <ammy.yi@intel.com> Signed-off-by:
Kan Liang <kan.liang@linux.intel.com> Signed-off-by:
Jiri Olsa <jolsa@kernel.org> Cc: <stable@vger.kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Fixes: 6f55967a ("perf/x86/intel: Fix race in intel_pmu_disable_event()") Link: https://lkml.kernel.org/r/20190625142135.22112-1-kan.liang@linux.intel.comSigned-off-by:
-
David Rientjes authored
commit e74bd969 upstream. When default_get_smp_config() is called with early == 1 and mpf->feature1 is non-zero, mpf is leaked because the return path does not do early_memunmap(). Fix this and share a common exit routine. Fixes: 5997efb9 ("x86/boot: Use memremap() to map the MPF and MPC data") Reported-by:
Cfir Cohen <cfir@google.com> Signed-off-by:
David Rientjes <rientjes@google.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1907091942570.28240@chino.kir.corp.google.comSigned-off-by:
-
Soeren Moch authored
commit 41a531ff upstream. Since commit ed194d13 ("usb: core: remove local_irq_save() around ->complete() handler") the handler rt2x00usb_interrupt_rxdone() is not running with interrupts disabled anymore. So this completion handler is not guaranteed to run completely before workqueue processing starts for the same queue entry. Be sure to set all other flags in the entry correctly before marking this entry ready for workqueue processing. This way we cannot miss error conditions that need to be signalled from the completion handler to the worker thread. Note that rt2x00usb_work_rxdone() processes all available entries, not only such for which queue_work() was called. This patch is similar to what commit df71c9cf ("rt2x00: fix order of entry flags modification") did for TX processing. This fixes a regression on a RT5370 based wifi stick in AP mode, which suddenly stopped data transmission after some period of heavy load. Also stopping the hanging hostapd resulted in the error message "ieee80211 phy0: rt2x00queue_flush_queue: Warning - Queue 14 failed to flush". Other operation modes are probably affected as well, this just was the used testcase. Fixes: ed194d13 ("usb: core: remove local_irq_save() around ->complete() handler") Cc: stable@vger.kernel.org # 4.20+ Signed-off-by:
Soeren Moch <smoch@web.de> Acked-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
YueHaibing authored
commit d4548543 upstream. KASAN report this: BUG: unable to handle kernel paging request at ffffffffa0097000 PGD 3870067 P4D 3870067 PUD 3871063 PMD 2326e2067 PTE 0 Oops: 0000 [#1 CPU: 0 PID: 5340 Comm: modprobe Not tainted 5.1.0-rc7+ #25 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014 RIP: 0010:__list_add_valid+0x10/0x70 Code: c3 48 8b 06 55 48 89 e5 5d 48 39 07 0f 94 c0 0f b6 c0 c3 90 90 90 90 90 90 90 55 48 89 d0 48 8b 52 08 48 89 e5 48 39 f2 75 19 <48> 8b 32 48 39 f0 75 3a RSP: 0018:ffffc90000e23c68 EFLAGS: 00010246 RAX: ffffffffa00ad000 RBX: ffffffffa009d000 RCX: 0000000000000000 RDX: ffffffffa0097000 RSI: ffffffffa0097000 RDI: ffffffffa009d000 RBP: ffffc90000e23c68 R08: 0000000000000001 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: ffffffffa0097000 R13: ffff888231797180 R14: 0000000000000000 R15: ffffc90000e23e78 FS: 00007fb215285540(0000) GS:ffff888237a00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffa0097000 CR3: 000000022f144000 CR4: 00000000000006f0 Call Trace: v9fs_register_trans+0x2f/0x60 [9pnet ? 0xffffffffa0087000 p9_virtio_init+0x25/0x1000 [9pnet_virtio do_one_initcall+0x6c/0x3cc ? kmem_cache_alloc_trace+0x248/0x3b0 do_init_module+0x5b/0x1f1 load_module+0x1db1/0x2690 ? m_show+0x1d0/0x1d0 __do_sys_finit_module+0xc5/0xd0 __x64_sys_finit_module+0x15/0x20 do_syscall_64+0x6b/0x1d0 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x7fb214d8e839 Code: 00 f3 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 RSP: 002b:00007ffc96554278 EFLAGS: 00000246 ORIG_RAX: 0000000000000139 RAX: ffffffffffffffda RBX: 000055e67eed2aa0 RCX: 00007fb214d8e839 RDX: 0000000000000000 RSI: 000055e67ce95c2e RDI: 0000000000000003 RBP: 000055e67ce95c2e R08: 0000000000000000 R09: 000055e67eed2aa0 R10: 0000000000000003 R11: 0000000000000246 R12: 0000000000000000 R13: 000055e67eeda500 R14: 0000000000040000 R15: 000055e67eed2aa0 Modules linked in: 9pnet_virtio(+) 9pnet gre rfkill vmw_vsock_virtio_transport_common vsock [last unloaded: 9pnet_virtio CR2: ffffffffa0097000 ---[ end trace 4a52bb13ff07b761 If register_virtio_driver() fails in p9_virtio_init, we should call v9fs_unregister_trans() to do cleanup. Link: http://lkml.kernel.org/r/20190430115942.41840-1-yuehaibing@huawei.com Cc: stable@vger.kernel.org Reported-by:
Hulk Robot <hulkci@huawei.com> Fixes: b530cc79 ("9p: add virtio transport") Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
Dominique Martinet <dominique.martinet@cea.fr> Signed-off-by:
-
